def printerBedCommand():
if not printer.isOperational():
return make_response("Printer is not operational", 409)
valid_commands = {"target": ["target"], "offset": ["offset"]}
command, data, response = util.getJsonCommandFromRequest(request, valid_commands)
if response is not None:
return response
##~~ temperature
if command == "target":
target = data["target"]
# make sure the target is a number
if not isinstance(target, (int, long, float)):
return make_response("Not a number: %r" % target, 400)
# perform the actual temperature command
printer.setTemperature("bed", target)
##~~ temperature offset
elif command == "offset":
offset = data["offsets"]
# make sure the offset is valid
if not isinstance(offset, (int, long, float)):
return make_response("Not a number: %r" % offset, 400)
if not -50 <= offset <= 50:
return make_response("Offset not in range [-50, 50]: %f" % offset, 400)
# set the offsets
printer.setTemperatureOffset({"bed": offset})
return NO_CONTENT
def printerBedCommand():
if not printer.isOperational():
return make_response("Printer is not operational", 409)
valid_commands = {
"target": ["target"],
"offset": ["offset"]
}
command, data, response = util.getJsonCommandFromRequest(request, valid_commands)
if response is not None:
return response
##~~ temperature
if command == "target":
target = data["target"]
# make sure the target is a number
if not isinstance(target, (int, long, float)):
return make_response("Not a number: %r" % target, 400)
# perform the actual temperature command
printer.setTemperature("bed", target)
##~~ temperature offset
elif command == "offset":
offset = data["offset"]
# make sure the offset is valid
if not isinstance(offset, (int, long, float)):
return make_response("Not a number: %r" % offset, 400)
if not -50 <= offset <= 50:
return make_response("Offset not in range [-50, 50]: %f" % offset, 400)
# set the offsets
printer.setTemperatureOffset({"bed": offset})
return NO_CONTENT
def printerToolCommand():
if not printer.isOperational():
return make_response("Printer is not operational", 409)
valid_commands = {
"select": ["tool"],
"target": ["targets"],
"offset": ["offsets"],
"extrude": ["amount"]
}
command, data, response = util.getJsonCommandFromRequest(request, valid_commands)
if response is not None:
return response
validation_regex = re.compile("tool\d+")
##~~ tool selection
if command == "select":
tool = data["tool"]
if re.match(validation_regex, tool) is None:
return make_response("Invalid tool: %s" % tool, 400)
if not tool.startswith("tool"):
return make_response("Invalid tool for selection: %s" % tool, 400)
printer.changeTool(tool)
##~~ temperature
elif command == "target":
targets = data["targets"]
# make sure the targets are valid and the values are numbers
validated_values = {}
for tool, value in targets.iteritems():
if re.match(validation_regex, tool) is None:
return make_response("Invalid target for setting temperature: %s" % tool, 400)
if not isinstance(value, (int, long, float)):
return make_response("Not a number for %s: %r" % (tool, value), 400)
validated_values[tool] = value
# perform the actual temperature commands
for tool in validated_values.keys():
printer.setTemperature(tool, validated_values[tool])
##~~ temperature offset
elif command == "offset":
offsets = data["offsets"]
# make sure the targets are valid, the values are numbers and in the range [-50, 50]
validated_values = {}
for tool, value in offsets.iteritems():
if re.match(validation_regex, tool) is None:
return make_response("Invalid target for setting temperature: %s" % tool, 400)
if not isinstance(value, (int, long, float)):
return make_response("Not a number for %s: %r" % (tool, value), 400)
if not -50 <= value <= 50:
return make_response("Offset %s not in range [-50, 50]: %f" % (tool, value), 400)
validated_values[tool] = value
# set the offsets
printer.setTemperatureOffset(validated_values)
##~~ extrusion
elif command == "extrude":
if printer.isPrinting():
# do not extrude when a print job is running
return make_response("Printer is currently printing", 409)
amount = data["amount"]
if not isinstance(amount, (int, long, float)):
return make_response("Not a number for extrusion amount: %r" % amount, 400)
printer.extrude(amount, 250 if amount > 0 else 400)
return NO_CONTENT
def printerToolCommand():
if not printer.isOperational():
return make_response("Printer is not operational", 409)
valid_commands = {
"select": ["tool"],
"target": ["targets"],
"offset": ["offsets"],
"extrude": ["amount"]
}
command, data, response = util.getJsonCommandFromRequest(request, valid_commands)
if response is not None:
return response
validation_regex = re.compile("tool\d+")
##~~ tool selection
if command == "select":
tool = data["tool"]
if re.match(validation_regex, tool) is None:
return make_response("Invalid tool: %s" % tool, 400)
if not tool.startswith("tool"):
return make_response("Invalid tool for selection: %s" % tool, 400)
printer.changeTool(tool)
##~~ temperature
elif command == "target":
targets = data["targets"]
# make sure the targets are valid and the values are numbers
validated_values = {}
for tool, value in targets.iteritems():
if re.match(validation_regex, tool) is None:
return make_response("Invalid target for setting temperature: %s" % tool, 400)
if not isinstance(value, (int, long, float)):
return make_response("Not a number for %s: %r" % (tool, value), 400)
validated_values[tool] = value
# perform the actual temperature commands
for tool in validated_values.keys():
printer.setTemperature(tool, validated_values[tool])
##~~ temperature offset
elif command == "offset":
offsets = data["offsets"]
# make sure the targets are valid, the values are numbers and in the range [-50, 50]
validated_values = {}
for tool, value in offsets.iteritems():
if re.match(validation_regex, tool) is None:
return make_response("Invalid target for setting temperature: %s" % tool, 400)
if not isinstance(value, (int, long, float)):
return make_response("Not a number for %s: %r" % (tool, value), 400)
if not -50 <= value <= 50:
return make_response("Offset %s not in range [-50, 50]: %f" % (tool, value), 400)
validated_values[tool] = value
# set the offsets
printer.setTemperatureOffset(validated_values)
##~~ extrusion
elif command == "extrude":
if printer.isPrinting():
# do not extrude when a print job is running
return make_response("Printer is currently printing", 409)
amount = data["amount"]
speedTarget = data["speed"]
if not isinstance(amount, (int, long, float)):
return make_response("Not a number for extrusion amount: %r" % amount, 400)
#printer.extrude(amount)
print("speed=%s" % str(speedTarget))
printer.extrudeSpeed(amount, speedTarget)
return NO_CONTENT
