• The current SD card image has everything you need!
• Read the Low-cost-LoRa-device leaflet
• Read the Low-cost-LoRa-GW leaflet
• Look at the Low-cost-LoRa-GW web admin interface tutorial. For most end-users, the web admin interface is sufficient to configure and manage the gateway. For instance, to configure a new gateway, it is recommended to use the web admin interface to update the gateway software and to run the basic configuration procedure as described here.
• The rest of this README file contains additional information to better understand the proposed low-cost IoT framework.

Also consult the following web page: http://cpham.perso.univ-pau.fr/LORA/RPIgateway.html

3 tutorial videos on YouTube: video of all the steps to build the whole framework from scratch:

• Build your low-cost, long-range IoT device with WAZIUP
• Extreme low-cost & low-power LoRa IoT for real-world deployment
• Build your low-cost LoRa gateway with WAZIUP

Go to https://github.com/CongducPham/tutorials for all tutorials and particularly look for:

• Low-cost-LoRa-GW leaflet
• Low-cost-LoRa-device leaflet
• Low-cost-LoRa-IoT-step-by-step tutorial
• Low-cost-LoRa-GW-step-by-step tutorial
• Low-cost-LoRa-GW web admin interface tutorial
• Low-cost-LoRa-IoT-antennaCable tutorial

Look also at our FAQ!

• a simple, user-friendly web admin interface to configure and update your gateway
  • open a browser and go to http://gw_ip_address/admin
  • README
  • Tutorial
  • raspap-webgui from https://github.com/billz/raspap-webgui has been integrated and can be accessed at http://gw_ip_address/raspap-webgui. When the gateway is configured as a WiFi client, raspap-webgui is especially useful to dynamically discover and configure additional WiFi networks. Read this section prior to use raspap-webgui.
• simple, flexible and generic cloud management approach
  • README
  • Look at the provided cloud script examples to see how IoT clouds such as ThingSpeak, GroveStreams, MQTT,... are supported
  • a cloud script can be used to generalize the upload of data using SMS, ftp, file, MQTT, Node-Red flow,...
• encryption and native LoRaWAN frame format
  • see README
  • end-device can send native LoRaWAN packets (for instance using a LoRaWAN radio chip such as RN2483)
  • low-level gateway provides raw output for post_processing_gw.py to handle LoRaWAN packets
• downlink features: to send from gateway to end-device
  • README
• an alert mail can be sent to a list of contact email addresses to notify when gateway is starting and when the radio module has been reset
• periodic status report to monitor whether the post-processing stage of the gateway is up or not
• support for an embedded DHT22 temperature/humidity sensor to monitor the condition inside the gateway case
• there is a NoSQL MongoDB support and received data can be saved in the local database if this feature is activated. See here for more information on the local MongoDB structure.
• the gateway acts as the WiFi access-point. The SSID is WAZIUP_PI_GW_XXXXXXXXXX where XXXXXXXXXX is the last 5 hex bytes of gateway ID: WAZIUP_PI_GW_27EB27F90F for instance. It has IP address 192.168.200.1 and will lease IP addresses in the range of 192.168.200.100 and 192.168.200.120.
• there is an Apache web server with basic PHP forms to visualize graphically the received data of the MongoDB with any web browser. Just connect to http://192.168.200.1 with a web browser (could be from a smartphone) to get the graphic visualization of the data stored in the gateway's MongoDB database.
• there is the support of Bluetooth connection. A simple Android App running on Android smartphone displays the data stored in the gateway's MongoDB database.
• by default, incoming data are uploaded to our LoRa ThingSpeak test channel
• works out-of-the-box with the Arduino_LoRa_Simple_temp sketch

You have to connect a LoRa radio module to the Raspberry's GPIO header. Just connect the corresponding SPI pin (MOSI, MISO, CLK, CS).

      RPI            Radio module
   GND pin 25----------GND   (ground in)
   3V3 pin 17----------3.3V  (3.3V in)
CS/CE0 pin 24----------NSS   (CS chip select in)
   SCK pin 23----------SCK   (SPI clock in)
  MOSI pin 19----------MOSI  (SPI Data in)
  MISO pin 21----------MISO  (SPI Data out)

You can have a look at the "Low-cost-LoRa-GW-step-by-step" tutorial in our tutorial repository https://github.com/CongducPham/tutorials.

The full, latest distribution of the low-cost gateway is available in the gw_full_latest folder of the github repository: https://github.com/CongducPham/LowCostLoRaGw. It contains all the gateway control and post-processing software.

However, the simplest and recommended way to install a new gateway is to use our zipped SD card image based on the Jessie Raspbian OS and perform a new install of the gateway from this image. In this way you don't need to install the various additional packages that are required (as explained in an additional README describing all manual installation steps if you want to install from scratch). Once you have burnt the SD image on a 8GB (minimum) SD card, insert it in your Raspberry and power it.

The distribution supports Raspberry 1B+, RPI2, RPI3, RPI0 and RPI0W. For RPI1, RPI0 and RPI0W you need to run make lora_gateway as the default version is built for RPI2&RPI3. There is out-of-the-box WiFi support for RPI3 and RPI0W. For RPI1 and RPI2 see here for modifications to support some WiFi dongles.

Download our zipped SD card image. The current image has everything you need including:

• the simple gateway web admin interface for easy configuration and management
• mosquitto-clients package installed to have mosquitto_pub and mosquitto_sub commands
• Node-Red and npm upgraded with node-red-contrib-thingspeak42 installed
• a ready-to-use Node-Red flow to show how received data can be uploaded to MQTT brokers and ThingSpeak

It is not a MacOS X DMG package as the extension may be misleading, simply unzip the file and burn the dmg file to an SD card. Use an SD card of a minimum of 8GB. Take also a class 10. If you have bigger SD card, e.g. 16GB, then after boot, use raspi-config (see tutorial here) to resize the partition in order to use the extra space available (you will need to reboot but raspi-config will ask you for that). You can use df -h to verify that you have more space after reboot.

You can look at various tutorials on how to burn an image to an SD card. There is one here from raspberrypi.org and here from elinux.org. I use a Mac to do so and this is my preferred solution. The Linux version is not very different. The Etcher tool is nice and you don't even need to unzip the SD card image.

Important notice: the LoRa gateway program starts automatically when the Raspberry is powered on.

You can try your gateway right away now by building your end-device and jump directly to this section.

If you want to connect (ssh) to the gateway and perform update procedure, read the rest of the section.

The SD card image defines a pi user:

- login: pi
- password: loragateway

With the default gateway configuration, the gateway acts as a WiFi access point. If you see the WiFi network WAZIUP_PI_GW_XXXXXXXXXX then connect to this WiFi network. The WiFi password is loragateway. It is strongly advise to change this WiFi password. The address of the Raspberry is then 192.168.200.1.

If you see no WiFi access point (e.g. RP1/RPI2/RPI0 without WiFi dongle), then plug your Raspberry into a DHCP-enabled box/router/network to get an IP address or shared your laptop internet connection to make your laptop acting as a DHCP server. On a Mac, there is a very simple solution here. For Windows, you can follow this tutorial or this one. You can then use Angry IP Scanner available on Windows/Mac/Linux/Android to determine the assigned IP address for the Raspberry.

We will use in this example 192.168.2.8 for the gateway address (DHCP option in order to have Internet access from the Raspberry)

> ssh pi@192.168.2.8
pi@192.168.200.1's password: 

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
Last login: Thu Aug  4 18:04:41 2016

For the Raspberry Zero, our SD card image set the RPI in access point mode. However, when in access-point mode, Ethernet over USB with dtoverlay=dwc2 in /boot/config.txt and modules-load=dwc2,g_ether in /boot/cmdline.txt is not working. As the usage of the Raspberry Zero is mainly with Internet connection through a cellular network (using for instance the LORANGA board from La Fabrica Alegre) the easiest way to have Internet through Ethernet sharing with our SD card image is to use a USB-Ethernet adapter that will add an eth0 interface on the RPI0. These USB-Ethernet adapter are quite cheap and are really useful on the RPI0 as you can then connect it to a DHCP-enabled router/box just like the other RPI boards. Alternatively, you can set your gateway as a WiFi client to connect to an existing WiFi network, see here.

Once you have your SD card flashed with our image, to get directly to the full, latest gateway version, you can either use (i) the web admin interface, or (ii) the provided update script to be run from the gateway, or (iii) download (git clone) the whole repository and copy the entire content of the gw_full_latest folder on your Raspberry, in a folder named lora_gateway or, (iv) get only (svn checkout) the gw_full_latest folder in a folder named lora_gateway. Option (i) is recommended and simple while (ii) is basically an automatization of option (iii) in command line mode. Both options (i) and (ii) however need Internet connectivity on the gateway while option (iii) and (iv) can be done on a computer prior to copy the files on the Raspberry.

It is the recommended option but the Raspberry must have Internet connection.

Choose the Gateway Update menu on the left. Then, if you install a brand new gateway with our SD card image, use New installation. For future updates, use Full update.

After New installation or Full update, run Basic config.

When using the web interface, you don't need to perform the manual Configuring your gateway after update step below.

It is also recommended to run Update web admin interface to update the web interface to the last version, after New installation or Full update.

Then reboot.

The full LoRa gateway with post-processing stage starts automatically when the Raspberry is powered on. By default, incoming data are uploaded to our LoRa ThingSpeak test channel. It will work out-of-the-box with the Arduino_LoRa_Simple_temp sketch.

If your gateway has Internet connectivity (DHCP with Internet sharing on your laptop for instance), you can use our update_gw.sh script. Even if the SD card image has a recent version of the gateway software with the update_gw.sh script in the lora_gateway/scripts folder it is safer to get the latest version of this script. Simply do:

> cd /home/pi
> wget https://raw.githubusercontent.com/CongducPham/LowCostLoRaGw/master/gw_full_latest/scripts/update_gw.sh
> chmod +x update_gw.sh
> ./update_gw.sh

Note that if you have customized configuration files (i.e. key_*, gateway_conf.json, clouds.json and radio.makefile) in the existing /home/pi/lora_gateway folder, then update_gw.sh will preserve all these configuration files. As the repository does not have a gateway_id.txt file, it will also preserve your gateway id.

Otherwise, if it is really the first time you install the gateway, then you can delete the lora_gateway folder before running the script:

> rm -rf lora_gateway
> ./update_gw.sh

This upgrade solution can be done on the Raspberry if it has Internet connectivity or on your laptop which is assumed to have Internet connectivity. If you don't have git installed on your laptop, you have to install it first. Then get all the repository:

> cd /home/pi
> git clone https://github.com/CongducPham/LowCostLoRaGw.git

You will get the entire repository:

pi@raspberrypi:~ $ ls -l LowCostLoRaGw/
total 32
drwxr-xr-x 7 pi pi  4096 Apr  1 15:38 Arduino
-rw-r--r-- 1 pi pi 15522 Apr  1 15:38 README.md	
drwxr-xr-x 2 pi pi  4096 Apr  1 15:38 gw_full_latest	
drwxr-xr-x 2 pi pi  4096 Apr  1 15:38 tutorials

Create a folder named lora_gateway (or if you already have one, then delete all its content) then copy all the files of the LowCostLoRaGw/gw_full_latest folder in it.

> mkdir lora_gateway
> cd lora_gateway
> cp -R ../LowCostLoRaGw/gw_full_latest/* .

Or if you want to "move" the LowCostLoRaGw/gw_full_latest folder, simply do (without creating the lora_gateway folder before):

> mv LowCostLoRaGw/gw_full_latest ./lora_gateway  

If you download the repository from your laptop, then rename gw_full_latest into lora_gateway and copy the entire lora_gateway folder into the Raspberry using scp for instance. In the example below, the laptop has wired Internet connectivity and use the gateway's advertised WiFi to connect to the gateway. Therefore the IP address of the gateway is 192.168.200.1.

> scp -r lora_gateway pi@192.168.200.1:/home/pi

If you don't want to use/install git, use your laptop to get the .zip file of the entire github with the "Clone or download" option, unzip the package, rename the gw_full_latest folder as lora_gateway and perform the scp command.

This upgrade solution can be done on the Raspberry if it has Internet connectivity or on your laptop which is assumed to have Internet connectivity. If you don't have svn installed on your laptop, you have to install it first. Then get only the gateway part:

> cd /home/pi
> svn checkout https://github.com/CongducPham/LowCostLoRaGw/trunk/gw_full_latest lora_gateway

That will create the lora_gateway folder and get all the file of (GitHub) LowCostLoRaGw/gw_full_latest in it.

To install svn on the Raspberry:

> sudo apt-get install subversion	

Here, again, you can do all these steps on your laptop and then use scp to copy to the Raspberry.

After gateway update with option (ii), (iii) or (iv), you need to configure your new gateway with basic_config_gw.sh, that mainly assigns the gateway id so that it is uniquely identified (the gateway's WiFi access point SSID is based on that gateway id for instance). The gateway id will be the last 5 bytes of the Rapberry eth0 MAC address (or wlan0 on an RPI0W without Ethernet adapter) and the configuration script will extract this information for you. There is an additional script called test_gwid.sh in the script folder to test whether the gateway id can be easily determined. In the scripts folder, simply run test_gwid.sh:

> cd /home/pi/lora_gateway/scripts
> ./test_gwid.sh
Detecting gw id as 00000027EBBEDA21

If you don't see something similar to 00000027EBBEDA21 (8 bytes in hex format) then you have to explicitly provide the last 5 bytes of the gw id to basic_config_gw.sh. Otherwise, in the scripts folder, simply run basic_config_gw.sh to automatically configure your gateway.

> cd /home/pi/lora_gateway/scripts
> ./basic_config_gw.sh

or

> ./basic_config_gw.sh 27EBBEDA21

If you need more advanced configuration, then run config_gw.sh as described here. However, basic_config_gw.sh should be sufficient for most of the cases. The script also compile the low-level gateway program corresponding to you Raspberry model. After configuration, reboot your Raspberry.

By default gateway_conf.json configures the gateway with a simple behavior: LoRa mode 1 (BW125SF12), no DHT sensor in gateway (so no MongoDB for DHT sensor), no downlink, no AES, no raw mode. clouds.json enables only the ThingSpeak demo channel (even the local MongoDB storage is disabled). You can customize your gateway later when you have more cloud accounts and when you know better what features you want to enable.

The LoRa gateway starts automatically when RPI is powered on. Then use cmd.sh to execute the main operations on the gateway as described here.

To have an end-device, you have to connect a LoRa radio module to an Arduino board. Just connect the corresponding SPI pin (MOSI, MISO, CLK, CS/SS). On the Uno, Pro Mini, Mini, Nano, Teensy the mapping is as follows:

       Arduino      Radio module
         GND----------GND   (ground in)
         3V3----------3.3V  (3.3V in)
  SS pin D10----------NSS   (CS chip select in)
 SCK pin D13----------SCK   (SPI clock in)
MOSI pin D11----------MOSI  (SPI Data in)
MISO pin D12----------MISO  (SPI Data out)

On the MEGA, the SPI pin are as follows: 50 (MISO), 51 (MOSI), 52 (SCK). Starting from November 3rd, 2017, the CS pin is always pin number 10 on Arduino and Teensy boards. You can have a look at the Low-cost-LoRa-IoT-step-by-step tutorial in the tutorial repository https://github.com/CongducPham/tutorials.

There is an important issue regarding the radio modules. The Semtech SX1272/76 has actually 2 lines of RF power amplification (PA): a high efficiency PA up to 14dBm (RFO) and a high power PA up to 20dBm (PA_BOOST). Setting transmission power to L (Low), H (High), and M (Max) only uses the RFO and delivers 2dBm, 6dBm and 14dBm respectively. x (extreme) and X (eXtreme) use the PA_BOOST and deliver 14dBm and 20dBm respectively.

However even if the SX1272/76 chip has the PA_BOOST and the 20dBm features, not all radio modules (integrating these SX1272/76) do have the appropriate wiring and circuits to enable these features: it depends on the choice of the reference design that itself is guided by the main intended frequency band usage, and sometimes also by the target country's regulations (such as maximum transmitted power). So you have to check with the datasheet whether your radio module has PA_BOOST (usually check whether the PA_BOOST pin is wired) and 20dBm capability before using x or X. Some other radio modules only wire the PA_BOOST and not the RFO resulting in very bad range when trying to use the RFO mode (L, H, and M). In this case, one has to use x to indicate PA_BOOST usage to get 14dBm.

Practically, we only use either M (Max) or x (extreme) to have maximum range. They both deliver 14dBm but the difference is whether the RFO pin is used or the PA_BOOST. Therefore, when uploading a sketch on your board, you have to check whether your radio module needs the PA_BOOST in order to get significant output level in which case x should be used instead of M. All the examples start with:

// IMPORTANT
///////////////////////////////////////////////////////////////////////////////////////////////////////////
//
// uncomment if your radio is an HopeRF RFM92W, HopeRF RFM95W, Modtronix inAir9B, NiceRF1276
// or you known from the circuit diagram that output use the PABOOST line instead of the RFO line
//#define PABOOST
///////////////////////////////////////////////////////////////////////////////////////////////////////////  

Uncomment PABOOST if you have a HopeRF RFM92W or RFM95W, or a Modtronix inAir9B (if inAir9, leave commented) or a NiceRF1276. If you have another non listed radio module, try first by leaving PABOOST commented, then see whether the packet reception is correct with a reasonably high SNR (such as 6 to 10 dB) at some meters of the gateway. If not, then try with PABOOST uncommented.

As suggested by some people, we provide here a simple Ping-Pong program to upload on an Arduino board. First, install the Arduino IDE. You can use the latest one (we tested with 1.8.3). But then, check (see the board manager) that the Arduino AVR board library is not above 1.6.11 as there might be some compilation issues because of the change of the GCC AVR compiler. Then, in your sketch folder, copy the content of the Arduino folder of the distribution.

Run the gateway with:

> sudo ./lora_gateway

With the Arduino IDE, open the Arduino_LoRa_Ping_Pong sketch compile it and upload to an Arduino board. Check your radio module first, see Connect a radio module to your end-device above.

The end-device runs in LoRa mode 1 and has address 8. Open the Serial Monitor (38400 bauds) to see the output of the Arduino. It will send "Ping" to the gateway by requesting an ACK every 10s. If the ACK is received then it will display "Pong received from gateway!" otherwise it displays "No Pong from gw!". There is a version using an OLED display, Arduino_LoRa_Ping_Pong_LCD, that can be compiled for the Heltec ESP32 WiFi LoRa OLED board or a regular Arduino Pro Mini board (we use a Pro Mini or a Nano) with a 0.96inch OLED I2C display. Such device can be used as a very convenient simple range tester.

Note that in most operational scenarios, requesting ACK from the gateway is costly. Look at the next examples to see how we usually send data without requesting ACK.

Notice for low-cost/clone Arduino boards. If you get a low-cost Arduino board, such as those sold by most of Chinese manufacturer, the USB connectivity is probably based on the CH340 or CH341. To make your low-cost Arduino visible to your Arduino IDE, you need the specific driver. Look at http://sparks.gogo.co.nz/ch340.html or http://www.microcontrols.org/arduino-uno-clone-ch340-ch341-chipset-usb-drivers/. For MacOS, you can look at http://www.mblock.cc/posts/run-makeblock-ch340-ch341-on-mac-os-sierra which works for MacOS up to Sierra. For MacOS user that have the previous version of CH34x drivers and encountering kernel panic with Sierra, don't forget to delete previous driver installation: sudo rm -rf /System/Library/Extensions/usb.kext.

See the video here.

First, install the Arduino IDE. You can use the latest one (we tested with 1.8.3). But then, check (see the board manager) that the Arduino AVR board library is not above 1.6.11 as there might be some compilation issues because of the change of the GCC AVR compiler. Then, in your sketch folder, copy the content of the Arduino folder of the distribution.

With the Arduino IDE, open the Arduino_LoRa_Simple_temp sketch, compile it and upload to an Arduino board. Check your radio module first, see Connect a radio module to your end-device above.

The end-device runs in LoRa mode 1 and has address 6. It will send data to the gateway.

The default configuration uses an application key filter set to [5, 6, 7, 8].

Use a temperature sensor (e.g. LM35DZ) and plugged in pin A0 (analog 0). You can use a power pin to power your temperature sensor if you are not concerned about power saving. Otherwise, you can use digital 9 (the sketch set this pin HIGH when reading value, then sets it back to LOW) and activate low power mode (uncomment #define LOW_POWER), see below.

For low-power applications the Pro Mini from Sparkfun is certainly a good choice. This board can be either in the 5V or 3.3V version. With the Pro Mini, it is better to really use the 3.3V version running at 8MHz as power consumption will be reduced. Power for the radio module can be obtained from the VCC pin which is powered in 3.3v when USB power is used or when unregulated power is connected to the RAW pin. If you power your Pro Mini with the RAW pin you can use for instance 4 AA batteries to get 6V. If you use a rechargeable battery you can easily find 3.7V Li-Ion packs. In this case, you can inject directly into the VCC pin but make sure that you've unsoldered the power isolation jumper (Sparkfun Pro Mini) or removed the voltage regulator, see Pro Mini schematic on the Arduino web page. To greatly save power, you should remove the power led.

The current low-power version for Arduino board use the RocketScream Low Power library (https://github.com/rocketscream/Low-Power) and can support most Arduino platforms although the Pro Mini platform will probably exhibit the best energy saving (we measured 54uA current in sleep mode with the power led removed and 12uA when the voltage regulator is removed). You can buid the low-power version by uncommenting the LOW_POWER compilation define statement. Then set int idlePeriodInMin = 10; to the number of minutes between 2 wake-up. By default it is 10 minutes. There are good web site describing low-power optimization for the pro Mini: http://www.home-automation-community.com/arduino-low-power-how-to-run-atmega328p-for-a-year-on-coin-cell-battery/ or https://andreasrohner.at/posts/Electronics/How-to-modify-an-Arduino-Pro-Mini-clone-for-low-power-consumption/.

For the special case of Teensy boards (LC/31/32/35/36), the power saving mode uses the excellent work of Collin Duffy with the Snooze library included by the Teensyduino package. You can upgrade the Snooze library from the github https://github.com/duff2013/Snooze as version 6 is required to handle the new Teensy 35/36 boards. With the Teensy, you can further use the HIBERNATE mode by uncommenting LOW_POWER_HIBERNATE in the temperature example.

For the special of the Arduino Zero, waking up the board from deep sleep mode is done with the RTC. Therefore the RTCZero library from https://github.com/arduino-libraries/RTCZero is used and you need to install it before being able to compile the example for the Arduino Zero.

Depending on the sensor type, the computation to get the real temperature may be changed accordingly. Here is the instruction for the LM35DZ: http://www.instructables.com/id/ARDUINO-TEMPERATURE-SENSOR-LM35/

The default configuration also use the EEPROM to store the last packet sequence number in order to get it back when the sensor is restarted/rebooted. If you want to restart with a packet sequence number of 0, just comment the line #define WITH_EEPROM

Once flashed, the Arduino temperature sensor will send to the gateway the following message \!#3#TC/20.4 (TC is used as the nomenclature code and 20.4 is the measured temperature so you may not have the same value) prefixed by the application key every 10 minutes (with some randomization interval). This will trigger at the processing stage of the gateway the logging on the default ThinkSpeak channel (the test channel we provide) in field 3. At the gateway, 20.4 will be recorded on the provided ThingSpeak test channel in field 3 of the channel. If you go to https://thingspeak.com/channels/66794 you should see the reported value.

At the gateway side, the cloud script that handles the ThingSpeak cloud is CloudThingSpeak.py. As ThingSpeak is a simple and very popular IoT cloud, we enhanced CloudThingSpeak.py to be able to assign a specific channel write key and a specific chart (field index) depending on the sensor source address. It is also possible to assign a specific field offset depending on the nomenclature. For more detail, read the examples provided in the CloudThingSpeak.py script.

The program has been tested on Arduino Uno, Mega2560, Nano, Pro Mini, Mini, Due, Zero. We also tested on the TeensyLC/3.1/3.2, the Ideetron Nexus and the Feather32u4/M0. Starting from November 3rd, 2017, the SPI_SS pin (CS pin) is always pin number 10 on all Arduino and Teensy boards.

Notice for low-cost/clone Arduino boards. If you get a low-cost Arduino board, such as those sold by most of Chinese manufacturer, the USB connectivity is probably based on the CH340 or CH341. To make your low-cost Arduino visible to your Arduino IDE, you need the specific driver. Look at http://sparks.gogo.co.nz/ch340.html or http://www.microcontrols.org/arduino-uno-clone-ch340-ch341-chipset-usb-drivers/. For MacOS, you can look at http://www.mblock.cc/posts/run-makeblock-ch340-ch341-on-mac-os-sierra which works for MacOS up to Sierra. For MacOS user that have the previous version of CH34x drivers and encountering kernel panic with Sierra, don't forget to delete previous driver installation: sudo rm -rf /System/Library/Extensions/usb.kext.

With the Arduino IDE, open the Arduino_LoRa_InteractiveDevice sketch. Then compile it and upload to an Arduino board. It is better to use a more powerful Arduino platform for building the interactive device otherwise stability issues can occur (and especially with more RAM memory such as a MEGA, the Uno, ATMega328P, will be very unstable because of the small amount of memory).

By default, the interactive end-device has address 6 and runs in LoRa mode 1.

Enter \!SGSH52UGPVAUYG3S#1#21.6 in the input window and press RETURN

The command will be sent to the gateway and you should see the gateway pushing the data to the ThingSpeak test channel. If you go to https://thingspeak.com/channels/66794 you should see the reported value.

When testing with the interactive end-device, you should not use the --wappkey option for the post_processing_gw.py post-processing Python script otherwise your command will not be accepted as only text string without logging services will be received and displayed when --wappkey is set.

> sudo ./lora_gateway | python ./post_processing_gw.py | python ./log_gw

The gateway can also be based on an Arduino board, as described in the web page. With the Arduino IDE, open the Arduino_LoRa_Gateway sketch, compile the code and upload to an Arduino board. Then follow instructions on how to use the Arduino board as a gateway. It is better to use a more powerful (and with more RAM memory such as the MEGA) Arduino platform for building the gateway.

When your radio module can run in the 433MHz band (for instance when the radio is based on SX1276 or SX1278 chip, such as the inAir4 from Modtronics) then you can test running at 433MHz as follows:

• select line #define BAND433 in Arduino_LoRa_temp or Arduino_LoRa_Simple_temp
• compile the lora_gateway.cpp with #define BAND433
• or simply run your gateway with lora_gateway --mode 1 --freq 433.3 to be on the same setting than Arduino_LoRa_temp and Arduino_LoRa_Simple_temp
• there are 4 channels in the 433MHz band: 433.3MHz as CH_00_433, 433.6MHz as CH_01_433, 433.9MHz as CH_02_433 and 434.3MHz as CH_03_433. CH_00_433=433.3MHz is the default channel in the 433MHz band.

For 900MHz band the procedure is similar:

• select line #define BAND900 in Arduino_LoRa_temp or Arduino_LoRa_Simple_temp
• compile the lora_gateway.cpp with #define BAND900
• or simply run your gateway with lora_gateway --mode 1 --freq 913.88 to be on the same setting than Arduino_LoRa_temp and Arduino_LoRa_Simple_temp
• there are 13 channels in the 900MHz band: from CH_00_900 to CH_12_900. CH_05_900=913.88MHz is the default channel in the 900MHz band.

With sshfs:

• look at http://mitchtech.net/dropbox-on-raspberry-pi-via-sshfs/. No need of sudo gpasswd -a pi fuse on Jessie.

  sudo apt-get install sshfs

• then allow option user_allow_other in /etc/fuse.conf

with Dropbox uploader:

• look at http://anderson69s.com/2014/02/18/raspberry-pi-dropbox/
• look at http://raspi.tv/2013/how-to-use-dropbox-with-raspberry-pi
• look at https://github.com/andreafabrizi/Dropbox-Uploader
• but not tested yet and not supported yet

Pre-defined LoRa modes (from initial Libelium SX1272.h)

Pre-defined channels in 868MHz, 915MHz and 433MHz band (most of them from initial Libelium SX1272.h, except those marked with *). Frequencies in bold are those used by default in each band.

Verify if the low-level gateway program detects your radio module and if the radio module is working by simply run the low-level gateway program with:

> sudo ./lora_gateway

You should see the following output

SX1276 detected, starting.
SX1276 LF/HF calibration
...
^$**********Power ON: state 0
^$Default sync word: 0x12
^$LoRa mode 1
^$Setting mode: state 0
^$Channel CH_10_868: state 0
^$Set LoRa power dBm to 14
^$Power: state 0
^$Get Preamble Length: state 0
^$Preamble Length: 8
^$LoRa addr 1: state 0
^$SX1272/76 configured as LR-BS. Waiting RF input for transparent RF-serial bridge	

If one of the state result is different from 0 then it might be a power/current issue. If the Preamble Length is different from 8 then it can also be a power/current issue but also indicate more important failure of the radio module. Get the "faulty" radio module and connect it to an Arduino board running the interactive end-device sketch. If the Preamble Length is now correct, then retry again with the Raspberry gateway. If the problem on the Raspberry persists, try with another radio module.

• There is currently no control on the transmit time for both gateway and end-device. When using the library to create devices, you have to ensure that the transmit time of your device is not exceeding the legal maximum transmit time defined in the regulation of your country (for instance ETSI define 1% duty-cycle, i.e. 36s/hour).

• Although 900MHz band is supported (mostly for the US ISM band), the library does not implement the frequency hopping mechanism nor the limited dwell time (e.g. 400ms per transmission).

Enjoy! C. Pham