def catboard_blinky_host(clock, led, uart_tx, uart_rx):
"""
The LEDs are controlled from the RPi over the UART
to the FPGA.
"""
glbl = Global(clock, None)
ledreg = Signal(intbv(0)[8:])
# create the timer tick instance
tick_inst = glbl_timer_ticks(glbl, include_seconds=True)
# create the interfaces to the UART
fbustx = FIFOBus(width=8, size=4)
fbusrx = FIFOBus(width=8, size=4)
uart_fifo = FIFOBus(width=8, size=4)
# create the memmap (CSR) interface
memmap = Barebone(glbl, data_width=32, address_width=32)
# create the UART instance.
uart_inst = uartlite(glbl, uart_fifo,
serial_in=uart_rx,
serial_out=uart_tx)
#map uart_fifo to separate readpath and writepath
assign_rw = uart_fifo.assign_read_write_paths(fbusrx,fbustx)
# create the packet command instance
cmd_inst = command_bridge(glbl, fbusrx, fbustx, memmap)
@always_seq(clock.posedge, reset=None)
def beh_led_control():
memmap.done.next = not (memmap.write or memmap.read)
if memmap.write and memmap.mem_addr == 0x20:
ledreg.next = memmap.write_data
@always_comb
def beh_led_read():
if memmap.read and memmap.mem_addr == 0x20:
memmap.read_data.next = ledreg
else:
memmap.read_data.next = 0
# blink one of the LEDs
tone = Signal(intbv(0)[8:])
@always_seq(clock.posedge, reset=None)
def beh_assign():
if glbl.tick_sec:
tone.next = (~tone) & 0x1
led.next = ledreg | tone[5:]
return (tick_inst, uart_inst, cmd_inst, assign_rw,
beh_led_control, beh_led_read, beh_assign)
def catboard_blinky_host(clock, led, uart_tx, uart_rx):
"""
The LEDs are controlled from the RPi over the UART
to the FPGA.
"""
glbl = Global(clock, None)
ledreg = Signal(intbv(0)[8:])
# create the timer tick instance
tick_inst = glbl_timer_ticks(glbl, include_seconds=True)
# create the interfaces to the UART
fbustx = FIFOBus(width=8, size=4)
fbusrx = FIFOBus(width=8, size=4)
# create the memmap (CSR) interface
memmap = Barebone(glbl, data_width=32, address_width=32)
# create the UART instance.
uart_inst = uartlite(glbl,
fbustx,
fbusrx,
serial_in=uart_rx,
serial_out=uart_tx)
# create the packet command instance
cmd_inst = command_bridge(glbl, fbusrx, fbustx, memmap)
@always_seq(clock.posedge, reset=None)
def beh_led_control():
memmap.done.next = not (memmap.write or memmap.read)
if memmap.write and memmap.mem_addr == 0x20:
ledreg.next = memmap.write_data
@always_comb
def beh_led_read():
if memmap.read and memmap.mem_addr == 0x20:
memmap.read_data.next = ledreg
else:
memmap.read_data.next = 0
# blink one of the LEDs
tone = Signal(intbv(0)[8:])
@always_seq(clock.posedge, reset=None)
def beh_assign():
if glbl.tick_sec:
tone.next = (~tone) & 0x1
led.next = ledreg | tone[5:]
return (tick_inst, uart_inst, cmd_inst, beh_led_control, beh_led_read,
beh_assign)
def xula2_blinky_host(clock, reset, led, bcm14_txd, bcm15_rxd):
"""
The LEDs are controlled from the RPi over the UART
to the FPGA.
"""
glbl = Global(clock, reset)
ledreg = Signal(intbv(0)[8:])
# create the timer tick instance
tick_inst = glbl_timer_ticks(glbl, include_seconds=True)
# create the interfaces to the UART
uart_fifo = FIFOBus(width=8)
# create the memmap (CSR) interface
memmap = Barebone(glbl, data_width=32, address_width=32)
# create the UART instance.
uart_inst = uartlite(
glbl, uart_fifo, serial_in=bcm14_txd, serial_out=bcm15_rxd,
fifosize=4
)
# create the packet command instance
cmd_inst = command_bridge(glbl, uart_fifo, memmap)
@always_seq(clock.posedge, reset=reset)
def beh_led_control():
memmap.done.next = not (memmap.write or memmap.read)
if memmap.write and memmap.mem_addr == 0x20:
ledreg.next = memmap.write_data
@always_comb
def beh_led_read():
if memmap.read and memmap.mem_addr == 0x20:
memmap.read_data.next = ledreg
else:
memmap.read_data.next = 0
# blink one of the LEDs
tone = Signal(intbv(0)[8:])
@always_seq(clock.posedge, reset=None)
def beh_assign():
if glbl.tick_sec:
tone.next = (~tone) & 0x1
led.next = ledreg | tone[5:]
return myhdl.instances()
def _bench_command_bridge():
tbclk = clock.gen()
tbdut = command_bridge(glbl, fbtx, fbrx, memmap)
tbfii = fifo_fast(clock, reset, fbtx)
tbfio = fifo_fast(clock, reset, fbrx)
# @todo: add other bus types
tbmem = memmap_peripheral_bb(clock, reset, memmap)
# save the data read ...
read_value = []
@instance
def tbstim():
yield reset.pulse(32)
try:
# test a single address
pkt = CommandPacket(True, 0x0000)
yield pkt.put(fbtx)
yield pkt.get(fbrx, read_value, [0])
pkt = CommandPacket(False, 0x0000, [0x5555AAAA])
yield pkt.put(fbtx)
yield pkt.get(fbrx, read_value, [0x5555AAAA])
# test a bunch of random addresses
for ii in range(nloops):
randaddr = randint(0, (2**20) - 1)
randdata = randint(0, (2**32) - 1)
pkt = CommandPacket(False, randaddr, [randdata])
yield pkt.put(fbtx)
yield pkt.get(fbrx, read_value, [randdata])
except Exception as err:
print("Error: {}".format(str(err)))
traceback.print_exc()
yield delay(2000)
raise StopSimulation
return tbclk, tbdut, tbfii, tbfio, tbmem, tbstim
def bench_command_bridge():
tbclk = clock.gen()
tbdut = command_bridge(glbl, fbtx, fbrx, memmap)
tbfii = fifo_fast(clock, reset, fbtx)
tbfio = fifo_fast(clock, reset, fbrx)
# @todo: add other bus types
tbmem = memmap_peripheral_bb(clock, reset, memmap)
# save the data read ...
read_value = []
@instance
def tbstim():
yield reset.pulse(32)
try:
# test a single address
pkt = CommandPacket(True, 0x0000)
yield pkt.put(fbtx)
yield pkt.get(fbrx, read_value, [0])
pkt = CommandPacket(False, 0x0000, [0x5555AAAA])
yield pkt.put(fbtx)
yield pkt.get(fbrx, read_value, [0x5555AAAA])
# test a bunch of random addresses
for ii in range(nloops):
randaddr = randint(0, (2**20)-1)
randdata = randint(0, (2**32)-1)
pkt = CommandPacket(False, randaddr, [randdata])
yield pkt.put(fbtx)
yield pkt.get(fbrx, read_value, [randdata])
except Exception as err:
print("Error: {}".format(str(err)))
traceback.print_exc()
yield delay(2000)
raise StopSimulation
return tbclk, tbdut, tbfii, tbfio, tbmem, tbstim
def uart_blinky(clock, led, uart_tx, uart_rx):
"""
Uses UART module to control LEDs while blinking the first LED.
LEDs used are pins 0-7 on wing A.
Expected behavior after upload is that LED[0] blinks on/off.
When sending
0xDE 0x02 0x00 0x00 0x00 0x20 0x04 0xCA 0x00 0x00 0x00 0xFF
via serial connection, all LEDs should turn on.
For details about the message format see
/rhea/cores/memmap/command_bridge.py
"""
reset = ResetSignal(0, active=0, async=True)
glbl = Global(clock, reset)
ledreg = Signal(intbv(0)[8:])
# create the timer tick instance
tick_inst = glbl_timer_ticks(glbl, include_seconds=True)
# create the interfaces to the UART
fifobus = FIFOBus(width=8)
# create the memmap (CSR) interface
memmap = Barebone(glbl, data_width=32, address_width=32)
# create the UART instance.
uart_inst = uartlite(glbl,
fifobus,
serial_in=uart_rx,
serial_out=uart_tx,
fifosize=4)
# create the packet command instance
cmd_inst = command_bridge(glbl, fifobus, memmap)
@always_seq(clock.posedge, reset=reset)
def beh_led_control():
memmap.done.next = not (memmap.write or memmap.read)
if memmap.write and memmap.mem_addr == 0x20:
ledreg.next = memmap.write_data
@always_comb
def beh_led_read():
if memmap.read and memmap.mem_addr == 0x20:
memmap.read_data.next = ledreg
else:
memmap.read_data.next = 0
# blink one of the LEDs
tone = Signal(intbv(0)[8:])
reset_dly_cnt = Signal(intbv(0)[5:])
@always_seq(clock.posedge, reset=None)
def beh_assign():
if glbl.tick_sec:
tone.next = (~tone) & 0x1
led.next = ledreg | tone[5:]
@always(clock.posedge)
def reset_tst():
'''
For the first 4 clocks the reset is forced to lo
for clock 6 to 31 the reset is set hi
then the reset is lo
'''
if (reset_dly_cnt < 31):
reset_dly_cnt.next = reset_dly_cnt + 1
if (reset_dly_cnt <= 4):
reset.next = 1
if (reset_dly_cnt >= 5):
reset.next = 0
else:
reset.next = 1
return (tick_inst, cmd_inst, uart_inst, beh_led_control, beh_led_read,
beh_assign, reset_tst)
def atlys_blinky_host(clock, reset, led, sw, pmod,
uart_tx, uart_rx):
"""
This example is similar to the other examples in this directory but
the LEDs are controlled externally via command packets sent from a
host via the UART on the icestick.
"""
glbl = Global(clock, reset)
ledreg = Signal(intbv(0)[8:])
# create the timer tick instance
tick_inst = glbl_timer_ticks(glbl, include_seconds=True)
# create the interfaces to the UART
fifobus = FIFOBus(width=8)
# create the memmap (CSR) interface
memmap = Barebone(glbl, data_width=32, address_width=32)
# create the UART instance, cmd_tx is an internal loopback
# for testing (see below)
cmd_tx = Signal(bool(0))
uart_inst = uartlite(glbl, fifobus, uart_rx, cmd_tx)
# create the packet command instance
cmd_inst = command_bridge(glbl, fifobus, memmap)
@always_seq(clock.posedge, reset=reset)
def beh_led_control():
memmap.done.next = not (memmap.write or memmap.read)
if memmap.write and memmap.mem_addr == 0x20:
ledreg.next = memmap.write_data
@always_comb
def beh_led_read():
if memmap.read and memmap.mem_addr == 0x20:
memmap.read_data.next = ledreg
else:
memmap.read_data.next = 0
# blink one of the LEDs
status = [Signal(bool(0)) for _ in range(8)]
statusbv = ConcatSignal(*reversed(status))
@always_seq(clock.posedge, reset=reset)
def beh_assign():
# status / debug signals
if glbl.tick_sec:
status[0].next = not status[0]
status[1].next = memmap.mem_addr == 0x20
status[2].next = uart_rx
status[3].next = uart_tx
led.next = ledreg | statusbv | sw
pmod.next = 0
if sw[0]:
uart_tx.next = uart_rx
else:
uart_tx.next = cmd_tx
# @todo: PMOD OLED memmap control
return (tick_inst, uart_inst, cmd_inst,
beh_led_control, beh_led_read, beh_assign)
def catboard_blinky_host(clock, reset, led, uart_tx, uart_rx):
"""
The LEDs are controlled from the RPi over the UART
to the FPGA.
"""
glbl = Global(clock, None)
ledreg = Signal(intbv(0)[8:])
# create the timer tick instance
tick_inst = glbl_timer_ticks(glbl, include_seconds=True)
# create the interfaces to the UART
uart_fifo = FIFOBus(width=8, size=4)
# create the memmap (CSR) interface
memmap = Barebone(glbl, data_width=32, address_width=32)
# create the UART instance.
uart_inst = uartlite(glbl, uart_fifo,
serial_in=uart_rx,
serial_out=uart_tx)
# create the packet command instance
cmd_inst = command_bridge(glbl, uart_fifo, memmap)
@always(clock.posedge)
def beh_led_control():
memmap.done.next = not (memmap.write or memmap.read)
if memmap.write and memmap.mem_addr == 0x80:
ledreg.next = memmap.write_data
@always_comb
def set_data():
data_to_host0.next = z1 << 16 | z0
data_to_host1.next = z3 << 16 | z2
data_to_host2.next = z5 << 16 | z4
data_to_host3.next = z7 << 16 | z6
data_to_host4.next = z9 << 16 | z8
data_to_host5.next = z11 << 16 | z10
data_to_host6.next = z13 << 16 | z12
data_to_host7.next = z15 << 16 | z14
# blink one of the LEDs
tone = Signal(intbv(0)[8:])
@always(clock.posedge)
def beh_assign():
if glbl.tick_sec:
tone.next = (~tone) & 0x1
led.next = ledreg | tone[5:]
@always(clock.posedge)
def beh_my_ret_reg():
if memmap.read:
if (memmap.mem_addr == 72):
memmap.read_data.next = data_to_host0
if (memmap.mem_addr == 76):
memmap.read_data.next = data_to_host1
if (memmap.mem_addr == 80):
memmap.read_data.next = data_to_host2
if (memmap.mem_addr == 84):
memmap.read_data.next = data_to_host3
if (memmap.mem_addr == 88):
memmap.read_data.next = data_to_host4
if (memmap.mem_addr == 92):
memmap.read_data.next = data_to_host5
if (memmap.mem_addr == 96):
memmap.read_data.next = data_to_host6
if (memmap.mem_addr == 100):
memmap.read_data.next = data_to_host7
@always(clock.posedge)
def beh_my_registers():
if memmap.write:
if memmap.mem_addr == 0:
myregister0.next = memmap.write_data
elif memmap.mem_addr == 4:
myregister1.next = memmap.write_data
elif memmap.mem_addr == 8:
myregister2.next = memmap.write_data
elif memmap.mem_addr == 12:
myregister3.next = memmap.write_data
if memmap.mem_addr == 16:
myregister4.next = memmap.write_data
elif memmap.mem_addr == 20:
myregister5.next = memmap.write_data
elif memmap.mem_addr == 24:
myregister6.next = memmap.write_data
elif memmap.mem_addr == 28:
myregister7.next = memmap.write_data
if memmap.mem_addr == 32:
myregister8.next = memmap.write_data
elif memmap.mem_addr == 36:
myregister9.next = memmap.write_data
elif memmap.mem_addr == 40:
myregister10.next = memmap.write_data
elif memmap.mem_addr == 44:
myregister11.next = memmap.write_data
if memmap.mem_addr == 48:
myregister12.next = memmap.write_data
elif memmap.mem_addr == 52:
myregister13.next = memmap.write_data
elif memmap.mem_addr == 56:
myregister14.next = memmap.write_data
elif memmap.mem_addr == 60:
myregister15.next = memmap.write_data
elif memmap.mem_addr == 64:
upd0.next = 1
upd1.next = 1
upd2.next = 1
upd3.next = 1
upd4.next = 1
upd5.next = 1
upd6.next = 1
upd7.next = 1
upd8.next = 1
upd9.next = 1
upd10.next = 1
upd11.next = 1
upd12.next = 1
upd13.next = 1
upd14.next = 1
upd15.next = 1
elif memmap.mem_addr == 68:
upd0.next = 0
upd1.next = 0
upd2.next = 0
upd3.next = 0
upd4.next = 0
upd5.next = 0
upd6.next = 0
upd7.next = 0
upd8.next = 0
upd9.next = 0
upd10.next = 0
upd11.next = 0
upd12.next = 0
upd13.next = 0
upd14.next = 0
upd15.next = 0
jpeg0 = dwt(flgs0, upd0, lft0, sam0, rht0, lift0, done0, clock)
l2res0 = lift2res1(lift0,res0)
sign0 = signed2twoscomplement(res0, z0)
jpeg1 = dwt(flgs1, upd1, lft1, sam1, rht1, lift1, done1, clock)
l2res1 = lift2res1(lift1,res1)
sign1 = signed2twoscomplement(res1, z1)
jpeg2 = dwt(flgs2, upd2, lft2, sam2, rht2, lift2, done2, clock)
l2res2 = lift2res1(lift2,res2)
sign2 = signed2twoscomplement(res2, z2)
jpeg3 = dwt(flgs3, upd3, lft3, sam3, rht3, lift3, done3, clock)
l2res3 = lift2res1(lift3,res3)
sign3 = signed2twoscomplement(res3, z3)
jpeg4 = dwt(flgs4, upd4, lft4, sam4, rht4, lift4, done4, clock)
l2res4 = lift2res1(lift4,res4)
sign4 = signed2twoscomplement(res4, z4)
jpeg5 = dwt(flgs5, upd5, lft5, sam5, rht5, lift5, done5, clock)
l2res5 = lift2res1(lift5,res5)
sign5 = signed2twoscomplement(res5, z5)
jpeg6 = dwt(flgs6, upd6, lft6, sam6, rht6, lift6, done6, clock)
l2res6 = lift2res1(lift6,res6)
sign6 = signed2twoscomplement(res6, z6)
jpeg7 = dwt(flgs7, upd7, lft7, sam7, rht7, lift7, done7, clock)
l2res7 = lift2res1(lift7,res7)
sign7 = signed2twoscomplement(res7, z7)
inst_sig0 = toSig(clock, myregister0,flgs0,lft0,sam0,rht0)
inst_sig1 = toSig(clock, myregister1,flgs1,lft1,sam1,rht1)
inst_sig2 = toSig(clock, myregister2,flgs2,lft2,sam2,rht2)
inst_sig3 = toSig(clock, myregister3,flgs3,lft3,sam3,rht3)
inst_sig4 = toSig(clock, myregister4,flgs4,lft4,sam4,rht4)
inst_sig5 = toSig(clock, myregister5,flgs5,lft5,sam5,rht5)
inst_sig6 = toSig(clock, myregister6,flgs6,lft6,sam6,rht6)
inst_sig7 = toSig(clock, myregister7,flgs7,lft7,sam7,rht7)
jpeg8 = dwt(flgs8, upd8, lft8, sam8, rht8, lift8, done8, clock)
l2res8 = lift2res1(lift8,res8)
sign8 = signed2twoscomplement(res8, z8)
jpeg9 = dwt(flgs9, upd9, lft9, sam9, rht9, lift9, done9, clock)
l2res9 = lift2res1(lift9,res9)
sign9 = signed2twoscomplement(res9, z9)
jpeg10= dwt(flgs10, upd10, lft10, sam10, rht10, lift10, done10, clock)
l2res10= lift2res1(lift10,res10)
sign10= signed2twoscomplement(res10, z10)
jpeg11 = dwt(flgs11, upd11, lft11, sam11, rht11, lift11, done11, clock)
l2res11 = lift2res1(lift11,res11)
sign11 = signed2twoscomplement(res11, z11)
jpeg12 = dwt(flgs12, upd12, lft12, sam12, rht12, lift12, done12, clock)
l2res12 = lift2res1(lift12,res12)
sign12 = signed2twoscomplement(res12, z12)
jpeg13 = dwt(flgs13, upd13, lft13, sam13, rht13, lift13, done13, clock)
l2res13 = lift2res1(lift13,res13)
sign13 = signed2twoscomplement(res13, z13)
jpeg14 = dwt(flgs14, upd14, lft14, sam14, rht14, lift14, done14, clock)
l2res14 = lift2res1(lift14,res14)
sign14 = signed2twoscomplement(res14, z14)
jpeg15 = dwt(flgs15, upd15, lft15, sam15, rht15, lift15, done15, clock)
l2res15 = lift2res1(lift15,res15)
sign15 = signed2twoscomplement(res15, z15)
inst_sig8 = toSig(clock, myregister8,flgs8,lft8,sam8,rht8)
inst_sig9 = toSig(clock, myregister9,flgs9,lft9,sam9,rht9)
inst_sig10 = toSig(clock, myregister10,flgs10,lft10,sam10,rht10)
inst_sig11 = toSig(clock, myregister11,flgs11,lft11,sam11,rht11)
inst_sig12 = toSig(clock, myregister12,flgs12,lft12,sam12,rht12)
inst_sig13 = toSig(clock, myregister13,flgs13,lft13,sam13,rht13)
inst_sig14 = toSig(clock, myregister14,flgs14,lft14,sam14,rht14)
inst_sig15 = toSig(clock,myregister15,flgs15,lft15,sam15,rht15)
return instances()
def bench_command_bridge():
tbclk = clock.gen()
tbdut = command_bridge(glbl, fifobus, memmap)
readpath, writepath = FIFOBus(), FIFOBus()
readpath.clock = writepath.clock = clock
tbmap = fifobus.assign_read_write_paths(readpath, writepath)
tbftx = fifo_fast(reset, clock, writepath) # user write path
tbfrx = fifo_fast(reset, clock, readpath) # user read path
# @todo: add other bus types
tbmem = memmap_peripheral_bb(clock, reset, memmap)
# save the data read ...
read_value = []
@instance
def tbstim():
yield reset.pulse(32)
fifobus.read.next = False
fifobus.write.next = False
assert not fifobus.full
assert fifobus.empty
assert fifobus.read_data == 0
fifobus.write_data.next = 0
try:
# test a single address
pkt = CommandPacket(True, 0x0000)
yield pkt.put(readpath)
yield pkt.get(writepath, read_value, [0])
pkt = CommandPacket(False, 0x0000, [0x5555AAAA])
yield pkt.put(readpath)
yield pkt.get(writepath, read_value, [0x5555AAAA])
# test a bunch of random addresses
for ii in range(nloops):
randaddr = randint(0, (2**20)-1)
randdata = randint(0, (2**32)-1)
pkt = CommandPacket(False, randaddr, [randdata])
yield pkt.put(readpath)
yield pkt.get(writepath, read_value, [randdata])
except Exception as err:
print("Error: {}".format(str(err)))
traceback.print_exc()
yield delay(2000)
raise StopSimulation
wp_read, wp_valid = Signals(bool(0), 2)
wp_read_data = Signal(intbv(0)[8:])
wp_empty, wp_full = Signals(bool(0), 2)
@always_comb
def tbmon():
wp_read.next = writepath.read
wp_read_data.next = writepath.read_data
wp_valid.next = writepath.read_valid
wp_full.next = writepath.full
wp_empty.next = writepath.empty
return tbclk, tbdut, tbmap, tbftx, tbfrx, tbmem, tbstim, tbmon
def atlys_blinky_host(clock, reset, led, sw, pmod,
uart_tx, uart_rx):
"""
This example is similar to the other examples in this directory but
the LEDs are controlled externally via command packets sent from a
host via the UART on the icestick.
"""
glbl = Global(clock, reset)
ledreg = Signal(intbv(0)[8:])
# create the timer tick instance
tick_inst = glbl_timer_ticks(glbl, include_seconds=True)
# create the interfaces to the UART
fbustx = FIFOBus(width=8, size=32)
fbusrx = FIFOBus(width=8, size=32)
# create the memmap (CSR) interface
memmap = Barebone(glbl, data_width=32, address_width=32)
# create the UART instance.
cmd_tx = Signal(bool(0))
uart_inst = uartlite(glbl, fbustx, fbusrx, uart_rx, cmd_tx)
# create the packet command instance
cmd_inst = command_bridge(glbl, fbusrx, fbustx, memmap)
@always_seq(clock.posedge, reset=reset)
def beh_led_control():
memmap.done.next = not (memmap.write or memmap.read)
if memmap.write: # and memmap.mem_addr == 0x20:
ledreg.next = memmap.write_data
@always_comb
def beh_led_read():
if memmap.read and memmap.mem_addr == 0x20:
memmap.read_data.next = ledreg
else:
memmap.read_data.next = 0
# blink one of the LEDs
status = [Signal(bool(0)) for _ in range(8)]
statusbv = ConcatSignal(*reversed(status))
@always_seq(clock.posedge, reset=reset)
def beh_assign():
# status / debug signals
if glbl.tick_sec:
status[0].next = not status[0]
status[1].next = memmap.mem_addr == 0x20
status[2].next = uart_rx
status[3].next = uart_tx
led.next = ledreg | statusbv | sw
pmod.next = 0
if sw[0]:
uart_tx.next = uart_rx
else:
uart_tx.next = cmd_tx
# @todo: PMOD OLED memmap control
return (tick_inst, uart_inst, cmd_inst,
beh_led_control, beh_led_read, beh_assign)
def uart_blinky(clock, led, uart_tx, uart_rx):
"""
Uses UART module to control LEDs while blinking the first LED.
LEDs used are pins 0-7 on wing A.
Expected behavior after upload is that LED[0] blinks on/off.
When sending
0xDE 0x02 0x00 0x00 0x00 0x20 0x04 0xCA 0x00 0x00 0x00 0xFF
via serial connection, all LEDs should turn on.
For details about the message format see
/rhea/cores/memmap/command_bridge.py
"""
reset = ResetSignal(0, active=0, async=True)
glbl = Global(clock, reset)
ledreg = Signal(intbv(0)[8:])
# create the timer tick instance
tick_inst = glbl_timer_ticks(glbl, include_seconds=True)
# create the interfaces to the UART
fifobus = FIFOBus(width=8)
# create the memmap (CSR) interface
memmap = Barebone(glbl, data_width=32, address_width=32)
# create the UART instance.
uart_inst = uartlite(
glbl, fifobus, serial_in=uart_rx, serial_out=uart_tx,
fifosize=4
)
# create the packet command instance
cmd_inst = command_bridge(glbl, fifobus, memmap)
@always_seq(clock.posedge, reset=reset)
def beh_led_control():
memmap.done.next = not (memmap.write or memmap.read)
if memmap.write and memmap.mem_addr == 0x20:
ledreg.next = memmap.write_data
@always_comb
def beh_led_read():
if memmap.read and memmap.mem_addr == 0x20:
memmap.read_data.next = ledreg
else:
memmap.read_data.next = 0
# blink one of the LEDs
tone = Signal(intbv(0)[8:])
reset_dly_cnt = Signal(intbv(0)[5:])
@always_seq(clock.posedge, reset=None)
def beh_assign():
if glbl.tick_sec:
tone.next = (~tone) & 0x1
led.next = ledreg | tone[5:]
@always(clock.posedge)
def reset_tst():
'''
For the first 4 clocks the reset is forced to lo
for clock 6 to 31 the reset is set hi
then the reset is lo
'''
if (reset_dly_cnt < 31):
reset_dly_cnt.next = reset_dly_cnt + 1
if (reset_dly_cnt <= 4):
reset.next = 1
if (reset_dly_cnt >= 5):
reset.next = 0
else:
reset.next = 1
return (tick_inst, cmd_inst, uart_inst,
beh_led_control, beh_led_read, beh_assign, reset_tst)
def xula2_blinky_host(clock, led, bcm14_txd, bcm15_rxd,a_dstb,a_astb,a_write,a_wait,to_rpi2B,fr_rpi2B):
"""
The LEDs are controlled from the RPi over the UART
to the FPGA.
"""
a_astb_sr = Signal(intbv(0)[3:])
a_dstb_sr = Signal(intbv(0)[3:])
a_addr_reg = Signal(intbv(0)[8:])
a_data_reg = Signal(intbv(0)[8:])
reset = ResetSignal(0, active=0,async=True)
glbl = Global(clock, reset)
ledreg = Signal(intbv(0)[8:])
# create the timer tick instance
tick_inst = glbl_timer_ticks(glbl, include_seconds=True)
# create the interfaces to the UART
uart_fifo = FIFOBus(width=8, size=4)
# create the memmap (CSR) interface
memmap = Barebone(glbl, data_width=32, address_width=32)
# create the UART instance.
uart_inst = uartlite(glbl, uart_fifo,
serial_in=bcm14_txd,
serial_out=bcm15_rxd)
# create the packet command instance
cmd_inst = command_bridge(glbl, uart_fifo, memmap)
@always_seq(clock.posedge, reset=reset)
def beh_led_control():
memmap.done.next = not (memmap.write or memmap.read)
if memmap.write and memmap.mem_addr == 0x20:
ledreg.next = memmap.write_data
@always_comb
def beh_led_read():
if memmap.read and memmap.mem_addr == 0x20:
memmap.read_data.next = ledreg
else:
memmap.read_data.next = 0
# blink one of the LEDs
tone = Signal(intbv(0)[8:])
reset_dly_cnt = Signal(intbv(0)[5:])
@always_seq(clock.posedge, reset=None)
def beh_assign():
if glbl.tick_sec:
tone.next = (~tone) & 0x1
led.next = ledreg | tone[5:]
@always(clock.posedge)
def reset_tst():
'''
For the first 4 clocks the reset is forced to lo
for clock 6 to 31 the reset is set hi
then the reset is lo
'''
if (reset_dly_cnt < 31):
reset_dly_cnt.next = reset_dly_cnt + 1
if (reset_dly_cnt <= 4):
reset.next = 1
if (reset_dly_cnt >= 5):
reset.next = 0
else:
reset.next = 1
@always_comb
def rtl1():
a_wait.next = (not a_astb) or (not a_dstb)
@always(clock.posedge)
def rtl2():
a_astb_sr.next = concat(a_astb_sr[2:0], a_astb)
a_dstb_sr.next = concat(a_dstb_sr[2:0], a_dstb)
@always(clock.posedge)
def rtl3():
if (~a_write and a_astb_sr == 4):
a_addr_reg.next = fr_rpi2B
@always(clock.posedge)
def rtl4():
if (~a_write and a_dstb_sr == 4):
a_data_reg.next = fr_rpi2B
@always(clock.posedge)
def rtl5():
if(a_write == 1):
to_rpi2B.next = a_data_reg
return (tick_inst, uart_inst, cmd_inst,
beh_led_control, beh_led_read, beh_assign, reset_tst,rtl1,rtl2,rtl3,rtl4,rtl5)
def bench_command_bridge():
tbclk = clock.gen()
tbdut = command_bridge(glbl, fifobus, memmap)
readpath, writepath = FIFOBus(), FIFOBus()
readpath.clock = writepath.clock = clock
tbmap = fifobus.assign_read_write_paths(readpath, writepath)
tbftx = fifo_fast(reset, clock, writepath) # user write path
tbfrx = fifo_fast(reset, clock, readpath) # user read path
# @todo: add other bus types
tbmem = memmap_peripheral_bb(clock, reset, memmap)
# save the data read ...
read_value = []
@instance
def tbstim():
yield reset.pulse(32)
fifobus.read.next = False
fifobus.write.next = False
assert not fifobus.full
assert fifobus.empty
assert fifobus.read_data == 0
fifobus.write_data.next = 0
try:
# test a single address
pkt = CommandPacket(True, 0x0000)
yield pkt.put(readpath)
yield pkt.get(writepath, read_value, [0])
pkt = CommandPacket(False, 0x0000, [0x5555AAAA])
yield pkt.put(readpath)
yield pkt.get(writepath, read_value, [0x5555AAAA])
# test a bunch of random addresses
for ii in range(nloops):
randaddr = randint(0, (2**20) - 1)
randdata = randint(0, (2**32) - 1)
pkt = CommandPacket(False, randaddr, [randdata])
yield pkt.put(readpath)
yield pkt.get(writepath, read_value, [randdata])
except Exception as err:
print("Error: {}".format(str(err)))
traceback.print_exc()
yield delay(2000)
raise StopSimulation
wp_read, wp_valid = Signals(bool(0), 2)
wp_read_data = Signal(intbv(0)[8:])
wp_empty, wp_full = Signals(bool(0), 2)
@always_comb
def tbmon():
wp_read.next = writepath.read
wp_read_data.next = writepath.read_data
wp_valid.next = writepath.read_valid
wp_full.next = writepath.full
wp_empty.next = writepath.empty
return tbclk, tbdut, tbmap, tbftx, tbfrx, tbmem, tbstim, tbmon
def icestick_blinky_host(clock, led, pmod, uart_tx, uart_rx,
uart_dtr, uart_rts):
"""
This example is similar to the other examples in this directory but
the LEDs are controlled externally via command packets sent from a
host via the UART on the icestick.
Ports:
clock:
led:
pmod:
uart_tx:
uart_rx:
"""
glbl = Global(clock, None)
ledreg = Signal(intbv(0)[8:])
# create the timer tick instance
tick_inst = glbl_timer_ticks(glbl, include_seconds=True)
# create the interfaces to the UART
fbustx = FIFOBus(width=8, size=4)
fbusrx = FIFOBus(width=8, size=4)
uart_fifo = FIFOBus(width=8, size=4)
# create the memmap (CSR) interface
memmap = Barebone(glbl, data_width=32, address_width=32)
# create the UART instance.
uart_inst = uartlite(glbl, uart_fifo, uart_rx, uart_tx)
#map uart_fifo to separate readpath and writepath
assign_rw = uart_fifo.assign_read_write_paths(fbusrx,fbustx)
# create the packet command instance
cmd_inst = command_bridge(glbl, fbusrx, fbustx, memmap)
@always_seq(clock.posedge, reset=None)
def beh_led_control():
memmap.done.next = not (memmap.write or memmap.read)
if memmap.write and memmap.mem_addr == 0x20:
ledreg.next = memmap.write_data
@always_comb
def beh_led_read():
if memmap.read and memmap.mem_addr == 0x20:
memmap.read_data.next = ledreg
else:
memmap.read_data.next = 0
# blink one of the LEDs
tone = Signal(intbv(0)[8:])
@always_seq(clock.posedge, reset=None)
def beh_assign():
if glbl.tick_sec:
tone.next = (~tone) & 0x1
led.next = ledreg | tone[5:]
pmod.next = 0
# @todo: PMOD OLED memmap control
return (tick_inst, uart_inst, assign_rw, cmd_inst,
beh_led_control, beh_led_read, beh_assign)
def icestick_blinky_host(clock, led, pmod, uart_tx, uart_rx, uart_dtr,
uart_rts):
"""
This example is similar to the other examples in this directory but
the LEDs are controlled externally via command packets sent from a
host via the UART on the icestick.
(arguments == ports)
Arguments:
clock:
led:
pmod:
uart_tx:
uart_rx:
"""
glbl = Global(clock, None)
ledreg = Signal(intbv(0)[8:])
# create the timer tick instance
tick_inst = glbl_timer_ticks(glbl, include_seconds=True)
# create the interfaces to the UART
fifobus = FIFOBus(width=8)
# create the memmap (CSR) interface
memmap = Barebone(glbl, data_width=32, address_width=32)
# create the UART instance.
uart_inst = uartlite(glbl, fifobus, uart_rx, uart_tx)
# create the packet command instance
cmd_inst = command_bridge(glbl, fifobus, memmap)
@always_seq(clock.posedge, reset=None)
def beh_led_control():
memmap.done.next = not (memmap.write or memmap.read)
if memmap.write and memmap.mem_addr == 0x20:
ledreg.next = memmap.write_data
@always_comb
def beh_led_read():
if memmap.read and memmap.mem_addr == 0x20:
memmap.read_data.next = ledreg
else:
memmap.read_data.next = 0
# blink one of the LEDs
tone = Signal(intbv(0)[8:])
@always_seq(clock.posedge, reset=None)
def beh_assign():
if glbl.tick_sec:
tone.next = (~tone) & 0x1
led.next = ledreg | tone[5:]
pmod.next = 0
# @todo: PMOD OLED memmap control
return myhdl.instances()
