from pyA20Lime.gpio import gpio
from pyA20Lime.gpio import port
__author__ = "Stefan Mavrodiev"
__copyright__ = "Copyright 2014, Olimex LTD"
__credits__ = ["Stefan Mavrodiev"]
__license__ = "GPL"
__version__ = "2.0"
__maintainer__ = __author__
__email__ = "*****@*****.**"
led = port.PH2
gpio.init()
gpio.setcfg(led, gpio.OUTPUT)
try:
print ("Press CTRL+C to exit")
while True:
gpio.output(led, 1)
sleep(0.1)
gpio.output(led, 0)
sleep(0.1)
gpio.output(led, 1)
sleep(0.1)
gpio.output(led, 0)
sleep(0.1)
sleep(0.6)
from time import sleep
from pyA20Lime.gpio import gpio
from pyA20Lime.gpio import port
__author__ = "Stefan Mavrodiev"
__copyright__ = "Copyright 2014, Olimex LTD"
__credits__ = ["Stefan Mavrodiev"]
__license__ = "GPL"
__version__ = "2.0"
__maintainer__ = __author__
__email__ = "*****@*****.**"
led = port.PH2
gpio.init()
gpio.setcfg(led, gpio.OUTPUT)
try:
print("Press CTRL+C to exit")
while True:
gpio.output(led, 1)
sleep(0.1)
gpio.output(led, 0)
sleep(0.1)
gpio.output(led, 1)
sleep(0.1)
gpio.output(led, 0)
sleep(0.1)
sleep(0.6)
__author__ = "Stefan Mavrodiev"
__copyright__ = "Copyright 2014, Olimex LTD"
__credits__ = ["Stefan Mavrodiev"]
__license__ = "GPL"
__version__ = "2.0"
__maintainer__ = __author__
__email__ = "*****@*****.**"
led = connector.gpio0p0 # This is the same as port.PH2
button = connector.gpio3p40
"""Init gpio module"""
gpio.init()
"""Set directions"""
gpio.setcfg(led, gpio.OUTPUT)
gpio.setcfg(button, gpio.INPUT)
"""Enable pullup resistor"""
gpio.pullup(button, gpio.PULLUP)
#gpio.pullup(button, gpio.PULLDOWN) # Optionally you can use pull-down resistor
try:
print ("Press CTRL+C to exit")
while True:
state = gpio.input(button) # Read button state
"""Since we use pull-up the logic will be inverted"""
gpio.output(led, not state)
except KeyboardInterrupt:
from pyA20Lime.gpio import port
__author__ = "Stefan Mavrodiev"
__copyright__ = "Copyright 2014, Olimex LTD"
__credits__ = ["Stefan Mavrodiev"]
__license__ = "GPL"
__version__ = "2.0"
__maintainer__ = __author__
__email__ = "*****@*****.**"
led = connector.gpio0p0 # This is the same as port.PH2
button = connector.gpio3p40
"""Init gpio module"""
gpio.init()
"""Set directions"""
gpio.setcfg(led, gpio.OUTPUT)
gpio.setcfg(button, gpio.INPUT)
"""Enable pullup resistor"""
gpio.pullup(button, gpio.PULLUP)
#gpio.pullup(button, gpio.PULLDOWN) # Optionally you can use pull-down resistor
try:
print("Press CTRL+C to exit")
while True:
state = gpio.input(button) # Read button state
"""Since we use pull-up the logic will be inverted"""
gpio.output(led, not state)
except KeyboardInterrupt:
print("Goodbye.")