Exemple #1
0
 def Open(self,devname,adr,eosChar=10,eosMode=0x08|0x04):
     """
     Open(gpibdevice,address,eosChar,eosMode)
     Opens a connected device at the GPIB bus. gpibdevice means the
     controller, (mostly \"gpib1\"), address the address of the desired
     device in the range 1...31. The eosChar defines the EOS character
     (default is linefeed), eosMode may be a combination of bits ORed
     together. The following bits can be used:
     0x04: Terminate read when EOS is detected.
     0x08: Set EOI (End or identify line) with EOS on write function
     0x10: Compare all 8 bits of EOS byte rather than low 7 bits
           (all read and write functions). Default is 0x12
     For example:
     dev = wxGPIB()
     dev.Open(\"gpib1\",17)
     Opens the device with the address 17, linefeed as EOS (default)
     and eos mode with 0x04 and 0x08.
     Open returns >= 0 or a negativ value, if something going wrong.
     """
     self.device = wxctb.wxGPIB()
     dcs = wxctb.wxGPIB_DCS()
     dcs.m_address1 = adr
     dcs.m_eosChar = eosChar
     dcs.m_eosMode = eosMode
     result = self.device.Open(devname,dcs)
     return result
Exemple #2
0
 def Open(self, devname, adr, eosChar=10, eosMode=0x08 | 0x04):
     """
     Open(gpibdevice,address,eosChar,eosMode)
     Opens a connected device at the GPIB bus. gpibdevice means the
     controller, (mostly \"gpib1\"), address the address of the desired
     device in the range 1...31. The eosChar defines the EOS character
     (default is linefeed), eosMode may be a combination of bits ORed
     together. The following bits can be used:
     0x04: Terminate read when EOS is detected.
     0x08: Set EOI (End or identify line) with EOS on write function
     0x10: Compare all 8 bits of EOS byte rather than low 7 bits
           (all read and write functions). Default is 0x12
     For example:
     dev = wxGPIB()
     dev.Open(\"gpib1\",17)
     Opens the device with the address 17, linefeed as EOS (default)
     and eos mode with 0x04 and 0x08.
     Open returns >= 0 or a negativ value, if something going wrong.
     """
     self.device = wxctb.wxGPIB()
     dcs = wxctb.wxGPIB_DCS()
     dcs.m_address1 = adr
     dcs.m_eosChar = eosChar
     dcs.m_eosMode = eosMode
     result = self.device.Open(devname, dcs)
     return result
Exemple #3
0
 def Open(self, devname, adr):
     """
     Open(gpibdevice,address)
     Opens a connected device at the GPIB bus. gpibdevice means the
     controller, (mostly \"gpib1\"), address the address of the desired
     device in the range 1...31. For example:
     dev = wxGPIB()
     dev.Open(\"gpib1\",17)
     Opens the device with the address 17.
     Open returns >= 0 or a negativ value, if something going wrong.
     """
     self.device = wxctb.wxGPIB()
     dcs = wxctb.wxGPIB_DCS()
     dcs.m_address1 = adr
     result = self.device.Open(devname, dcs)
     return result
Exemple #4
0
 def Open(self, devname, adr):
     """
     Open(gpibdevice,address)
     Opens a connected device at the GPIB bus. gpibdevice means the
     controller, (mostly \"gpib1\"), address the address of the desired
     device in the range 1...31. For example:
     dev = wxGPIB()
     dev.Open(\"gpib1\",17)
     Opens the device with the address 17.
     Open returns >= 0 or a negativ value, if something going wrong.
     """
     self.device = wxctb.wxGPIB()
     dcs = wxctb.wxGPIB_DCS()
     dcs.m_address1 = adr
     result = self.device.Open(devname, dcs)
     return result