def countFails(scale, count):
zeros = 0
exceptions = 0
drone1 = sensors.thermometer()
drone2 = sensors.temperSensor()
switch1 = switches.coolerSwitch()
switch2 = switches.myX10('/dev/serial/by-id/usb-Prolific_Technology'
'_Inc._USB-Serial_Controller-if00-port0')
switch3 = switches.pumpUSB()
for x in range(0, count):
try:
d1 = drone1.getValue()
except:
sys.stdout.write('v')
try:
d2 = drone2.getValue()
except:
sys.stdout.write('t')
try:
s1 = switch1.off()
except:
sys.stdout.write('c')
try:
s2 = switch2.off()
except:
sys.stdout.write('x')
try:
s3 = switch3.off()
except:
sys.stdout.write('u')
try:
val = scale.getRaw()
if int(val) == 0:
zeros = zeros + 1
sys.stdout.write("0")
else:
sys.stdout.write(".")
except:
exceptions = exceptions + 1
sys.stdout.write("*")
sys.stdout.flush()
if x % 25 == 24:
print ""
print ""
print "Exceptions:", exceptions
print "Zeros :", zeros
def setupControllers(verbose, simulation, permissive, equipment):
controllers = ctrl.controllerList()
# The controllerinfo is a special snowflake that stores some extra global controller info
# It does not do anything intelligent itherwise and will always meet target
controllers.addController('controllerInfo', appliances.controllerinfo())
if equipment is None:
logging.error('Equipment is None')
return(None)
controllers['controllerInfo'].setEquipment(equipment)
# Timer is always required in all equipment
controllers.addController('delayTimer', appliances.hoptimer())
print "Try to find hw switches"
if not simulation:
logging.info("Initializing hardware")
x10 = None
try:
usbPumps = switches.pumpUSB()
except:
if permissive:
logging.info("**********USB pumps not found, simulating HW")
usbPumps = switches.simSwitchList()
else:
raise Exception("USB pumps not available")
else:
x10 = switches.simSwitchList()
usbPumps = switches.simSwitchList()
print("Setting up appliances")
hwTunSwitch = switches.powerSwitch(1)
boilerSwitch = switches.powerSwitch(2)
print 0
aeratorSwitch = switches.air8800Switch()
print 0.2
coolerSwitch = switches.coolerSwitch()
mashStirSwitch = switches.mashStirSwitch()
#mashStirSwitch = switches.mashStir8800Switch()
print 0.5
boilerValveSwitch = switches.boilerValveSwitch()
hotWaterPumpSwitch = usbPumps.getSwitch(1)
hwCirculationSwitch = usbPumps.getSwitch(0)
wortSwitch = usbPumps.getSwitch(2)
mashCirculationSwitch = usbPumps.getSwitch(3)
print 1
controllers.addController('waterHeater', appliances.hwt())
controllers['waterHeater'].connectSwitch(hwTunSwitch)
controllers['waterHeater'].setx(x10)
controllers.addController('boiler', appliances.boiler())
controllers['boiler'].connectSwitch(boilerSwitch)
controllers['boiler'].setx(x10)
controllers.addController('aerator', appliances.aerator())
controllers['aerator'].connectSwitch(aeratorSwitch)
print 2
controllers.addController('cooler', appliances.cooler())
controllers['cooler'].connectSwitch(coolerSwitch)
boilerSensor = controllers['boiler'].getSensor()
controllers['cooler'].connectSensor(boilerSensor)
# Reuse of same switch for plate cooler as immersion cooler
controllers.addController('plateValve', appliances.plateValve())
controllers['plateValve'].connectSwitch(coolerSwitch)
controllers.addController('mashStirrer', appliances.mashStirrer())
controllers['mashStirrer'].connectSwitch(mashStirSwitch)
controllers.addController('mashHeater', appliances.mashHeater())
controllers['mashHeater'].connectSwitch(mashCirculationSwitch)
print 5
controllers.addController('boilerValve', appliances.boilerValve())
controllers['boilerValve'].connectSwitch(boilerValveSwitch)
controllers.addController('hotWaterPump', appliances.hwPump())
controllers['hotWaterPump'].connectSwitch(hotWaterPumpSwitch)
controllers.addController('waterCirculationPump',
appliances.circulationPump())
controllers['waterCirculationPump'].connectSwitch(hwCirculationSwitch)
controllers.addController('wortPump', appliances.wortPump())
controllers['wortPump'].connectSwitch(wortSwitch)
controllers.addController('boilerVolume', appliances.boilerVolume())
controllers['boilerVolume'].attachHost(controllers['wortPump'])
# controllers.addController('mashCirculationPump', \
# appliances.circulationPump())
# controllers['mashCirculationPump'].connectSwitch(mashCirculationSwitch)
controllers.addController('dispenser1', appliances.dispenser(1))
controllers.addController('dispenser2', appliances.dispenser(2))
controllers.addController('dispenser3', appliances.dispenser(3))
controllers.addController('dispenser4', appliances.dispenser(4))
controllers.addController('envTemp', appliances.envTemp())
print("appliance setup done")
# Testing of sensor object Remove me later
for key, c1 in controllers.items():
c1.findOrAddSensor(controllers)
# print key
"returning..."
return(controllers)
