• Introduction
• Setup
  • Extractor
  • Database
  • Binaries
  • QEMU
• Usage
• FAQ
• Compiling from Source
  • Toolchain
  • console
  • libnvram
  • Kernel
    • ARM
    • MIPS
• Database
  • Data
  • Schema
• Paper

FIRMADYNE is an automated and scalable system for performing emulation and dynamic analysis of Linux-based embedded firmware. It includes the following components:

• modified kernels (MIPS: v2.6.32, ARM: v4.1, v3.10) for instrumentation of firmware execution;
• a userspace NVRAM library to emulate a hardware NVRAM peripheral;
• an extractor to extract a filesystem and kernel from downloaded firmware;
• a small console application to spawn an additional shell for debugging;
• and a scraper to download firmware from 42+ different vendors.

We have also written the following three basic automated analyses using the FIRMADYNE system.

• Accessible Webpages: This script iterates through each file within the filesystem of a firmware image that appears to be served by a webserver, and aggregates the results based on whether they appear to required authentication.
• SNMP Information: This script dumps the contents of the public and private SNMP v2c communities to disk using no credentials.
• Vulnerability Check: This script tests for the presence of 60 known vulnerabilities using exploits from Metasploit. In addition, it also checks for 14 previously-unknown vulnerbailities that we discovered. For more information, including affected products and CVE's, refer to analyses/README.md.

In our 2016 Network and Distributed System Security Symposium (NDSS) paper, titled Towards Automated Dynamic Analysis for Linux-based Embedded Firmware, we evaluated the FIRMADYNE system over a dataset of 23,035 firmware images, of which we were able to extract 9,486. Using 60 exploits from the Metasploit Framework, and 14 previously-unknown vulnerabilities that we discovered, we showed that 846 out of 1,971 (43%) firmware images were vulnerable to at least one exploit, which we estimate to affect 89+ different products. For more details, refer to our paper linked above.

Note: This project is a research tool, and is currently not production ready. In particular, some components are quite immature and rough. We suggest running the system within a virtual machine. No support is offered, but pull requests are greatly appreciated, whether for documentation, tests, or code!

The following has been tested on a Ubuntu 14.04 machine. Other Debian-based systems should also be compatible.

First, clone this repository recursively and install its dependencies.

1. sudo apt-get install busybox-static fakeroot git kpartx netcat-openbsd nmap python-psycopg2 python3-psycopg2 snmp uml-utilities util-linux vlan
2. git clone --recursive https://github.com/firmadyne/firmadyne.git

The extractor depends on the binwalk tool, so we need to install that and its dependencies.

1. git clone https://github.com/devttys0/binwalk.git
2. cd binwalk
3. sudo ./deps.sh
4. sudo python ./setup.py install

• For Python 2.x, sudo apt-get install python-lzma

4. sudo -H pip install git+https://github.com/ahupp/python-magic
5. sudo -H pip install git+https://github.com/sviehb/jefferson.
6. Optionally, instead of upstream sasquatch, our sasquatch fork can be used to prevent false positives by making errors fatal.

Next, install, set up, and configure the database.

1. sudo apt-get install postgresql
2. sudo -u postgres createuser -P firmadyne, with password firmadyne
3. sudo -u postgres createdb -O firmadyne firmware
4. sudo -u postgres psql -d firmware < ./firmadyne/database/schema

To download our pre-built binaries for all components, run the following script:

• cd ./firmadyne; ./download.sh

Alternatively, refer to the instructions below to compile from source.

To use QEMU provided by your distribution:

• sudo apt-get install qemu-system-arm qemu-system-mips qemu-system-x86 qemu-utils

Note that emulation of x86-based firmware is not currently supported, but installing qemu-system-x86 resolves a packaging issue on certain Debian-based distributions.

Alternatively, use our modified version of qemu-linaro for certain firmware with an alphafs webserver that assumes a fixed memory mapping (not recommended), or upstream qemu.

1. Set FIRMWARE_DIR in firmadyne.config to point to the root of this repository.
2. Download a firmware image, e.g. v2.0.3 for Netgear WNAP320.
   • wget http://www.downloads.netgear.com/files/GDC/WNAP320/WNAP320%20Firmware%20Version%202.0.3.zip
3. Use the extractor to recover only the filesystem, no kernel (-nk), no parallel operation (-np), populating the image table in the SQL server at 127.0.0.1 (-sql) with the Netgear brand (-b), and storing the tarball in images.
   • ./sources/extractor/extractor.py -b Netgear -sql 127.0.0.1 -np -nk "WNAP320 Firmware Version 2.0.3.zip" images
4. Identify the architecture of firmware 1 and store the result in the image table of the database.
   • ./scripts/getArch.sh ./images/1.tar.gz
5. Load the contents of the filesystem for firmware 1 into the database, populating the object and object_to_image tables.
   • ./scripts/tar2db.py -i 1 -f ./images/1.tar.gz
6. Create the QEMU disk image for firmware 1.
   • sudo ./scripts/makeImage.sh 1
7. Infer the network configuration for firmware 1. Kernel messages are logged to ./scratch/1/qemu.initial.serial.log.
   • ./scripts/inferNetwork.sh 1
8. Emulate firmware 1 with the inferred network configuration. This will modify the configuration of the host system by creating a TAP device and adding a route.
   • ./scratch/1/run.sh
9. The system should be available over the network, and is ready for analysis. Kernel messages are mirrored to ./scratch/1/qemu.final.serial.log.
   • ./analyses/snmpwalk.sh 192.168.0.100
   • ./analyses/webAccess.py 1 192.168.0.100 log.txt
   • mkdir exploits; ./analyses/runExploits.py -t 192.168.0.100 -o exploits/exploit -e x (requires Metasploit Framework)
   • sudo nmap -O -sV 192.168.0.100
10. The default console should be automatically connected to the terminal. Note that Ctrl-c is sent to the guest; use the QEMU monitor command Ctrl-a + x to terminate emulation. For the sample firmware above, you will first need to delete the file /etc/securetty from the filesystem to login as root with password password.
11. The following scripts can be used to mount/unmount the filesystem of firmware 1. Ensure that the emulated firmware is not running, and remember to unmount before performing any other operations.

• sudo ./scripts/mount.sh 1
• sudo ./scripts/umount.sh 1

This is a common error that is encountered when the network configuration is unable to be inferred. Follow the checklist below to figure out the cause.

1. inferNetwork.sh: Did this script find any network interfaces (e.g. Interfaces: [br0, 192.168.0.1])? If so, this is a bug; please report it. Otherwise, continue below.
2. qemu.initial.serial.log: Does this file end with Unable to mount root fs on unknown-block(8,1)? If so, the initial filesystem image was not generated correctly using kpartx. Try deleting the scratch directory corresponding to this firmware image, and restart at makeImage.sh. Otherwise, the initial emulation didn't produce any useful instrumentation. Try increasing the timeout in inferNetwork.sh from 60 to 120 and restarting at inferNetwork.sh.
3. qemu.initial.serial.log: Did the init process crash, and is this preceded by a failed NVRAM operation (e.g. nvram_get_buf: Unable to open key <foo>)? If so, a new NVRAM entry may need to be manually added to config.h in libnvram, with the expected value. Otherwise, it is likely that a disassembler will be needed to figure out why the boot process failed.

If you would like to compile the entire FIRMADYNE system from scratch without using our pre-built binaries, please follow the steps below.

In order to build any of the binaries used by FIRMADYNE, you will need three cross-compilation toolchains for the following architecture triples. Use only musl libc as the C runtime library for the toolchain; others have not been tested.

• arm-linux-musleabi
• mipseb-linux-musl
• mipsel-linux-musl

To simplify the process of building cross-compilation toolchains with musl, we recommend using the musl-cross project. Follow the below steps to build these toolchains from source, or alternatively click here to download our pre-built toolchains.

1. git clone https://github.com/GregorR/musl-cross.git

2. Modify or set the following variables in defs.sh

   • BINUTILS_URL=http://ftp.gnu.org/gnu/binutils/binutils-2.25.1.tar.bz2
   • GCC_VERSION=5.3.0
   • GMP_VERSION=6.0.0a
   • MPC_VERSION=1.0.2
   • MPFR_VERSION=3.1.3
   • LIBELF_VERSION=master
   • MUSL_DEFAULT_VERSION=1.1.12
   • MUSL_GIT_VERSION=615629bd6fcd6ddb69ad762e679f088c7bd878e2
   • LANG_CXX=no

3. Modify or set the following variables in config.sh

   • CFLAGS="-fPIC"

4. For little-endian MIPS, perform the following:

   • set TRIPLE=mipsel-linux-musl in config.sh
   • set LINUX_HEADERS_URL=https://kernel.org/pub/linux/kernel/v2.6/longterm/v2.6.32/linux-2.6.32.70.tar.xz in defs.sh
   • run ./clean.sh to clean out any previous builds
   • run ./build.sh to build and install the toolchain into /opt/cross

5. For big-endian MIPS, perform the following:

   • set TRIPLE=mipseb-linux-musl in config.sh
   • set LINUX_HEADERS_URL=https://kernel.org/pub/linux/kernel/v2.6/longterm/v2.6.32/linux-2.6.32.70.tar.xz in defs.sh
   • run ./clean.sh to clean out any previous builds
   • run ./build.sh to build and install the toolchain into /opt/cross

6. For little-endian ARM, perform the following:

   • set TRIPLE=arm-linux-musleabi, GCC_BOOTSTRAP_CONFFLAGS="--with-arch=armv6 --with-float=softfp", and GCC_CONFFLAGS="--with-arch=armv6 --with-float=softfp" in config.sh
   • set LINUX_HEADERS_URL=https://kernel.org/pub/linux/kernel/v4.x/linux-4.1.17.tar.xz in defs.sh
   • run ./clean.sh to clean out any previous builds
   • run ./build.sh to build and install the toolchain into /opt/cross

7. You should have the following directories, or wherever you installed the toolchains:

   • /opt/cross/arm-linux-musleabi
   • /opt/cross/mipseb-linux-musl
   • /opt/cross/mipsel-linux-musl

1. cd ./firmadyne/sources/console
2. make clean && CC=/opt/cross/arm-linux-musleabi/bin/arm-linux-musleabi-gcc make && mv console ../../binaries/console.armel
3. make clean && CC=/opt/cross/mipseb-linux-musl/bin/mipseb-linux-musl-gcc make && mv console ../../binaries/console.mipseb
4. make clean && CC=/opt/cross/mipsel-linux-musl/bin/mipsel-linux-musl-gcc make && mv console ../../binaries/console.mipsel

1. cd ./firmadyne/sources/libnvram
2. make clean && CC=/opt/cross/arm-linux-musleabi/bin/arm-linux-musleabi-gcc make && mv libnvram.so ../../binaries/libnvram.so.armel
3. make clean && CC=/opt/cross/mipseb-linux-musl/bin/mipseb-linux-musl-gcc make && mv libnvram.so ../../binaries/libnvram.so.mipseb
4. make clean && CC=/opt/cross/mipsel-linux-musl/bin/mipsel-linux-musl-gcc make && mv libnvram.so ../../binaries/libnvram.so.mipsel

1. git clone https://github.com/firmadyne/kernel-v4.1.git && cd kernel-v4.1
2. mkdir -p build/armel
3. cp config.armel build/armel/.config
4. make ARCH=arm CROSS_COMPILE=/opt/cross/arm-linux-musleabi/bin/arm-linux-musleabi- O=./build/armel zImage -j8
5. cp build/armel/arch/arm/boot/zImage ../firmadyne/binaries/zImage.armel

1. git clone https://github.com/firmadyne/kernel-v2.6.32.git && cd kernel-v2.6.32

2. For big-endian MIPS, perform the following:

   1. mkdir -p build/mipseb
   2. cp config.mipseb build/mipseb/.config
   3. make ARCH=mips CROSS_COMPILE=/opt/cross/mipseb-linux-musl/bin/mipseb-linux-musl- O=./build/mipseb -j8
   4. cp build/mipseb/vmlinux ../firmadyne/binaries/vmlinux.mipseb

3. For little-endian MIPS, perform the following:

   1. mkdir -p build/mipsel
   2. cp config.mipsel build/mipsel/.config
   3. make ARCH=mips CROSS_COMPILE=/opt/cross/mipsel-linux-musl/bin/mipsel-linux-musl- O=./build/mipsel -j8
   4. cp build/mipsel/vmlinux ../firmadyne/binaries/vmlinux.mipsel

During development, the database was stored on a PostgreSQL server.

Although we cannot redistribute binary firmware, the data used for our experiments is available here.

Below are descriptions of tables in the schema.

• brand: Stores brand names for each vendor.

• image: Stores information about each firmware image.

• object: Stores information about each file in a filesystem.

• object_to_image: Maps unique files to their firmware images.

• product

The results discussed in our paper were produced using pre-release versions of the following:

• toolchains:
  • BINUTILS_URL=http://ftp.gnu.org/gnu/binutils/binutils-2.25.1.tar.bz2, GCC_VERSION=4.9.3, GMP_VERSION=6.0.0a, MPC_VERSION=1.0.2, MPFR_VERSION=3.1.3, LIBELF_VERSION=71bf774909fd654d8167a475333fa8f37fbbcb5d, MUSL_DEFAULT_VERSION=1.1.10, MUSL_GIT_VERSION=996d148bf14b477b07fa3691bffeb930c67b2b62, LANG_CXX=no
  • ARM: LINUX_HEADERS_URL=https://kernel.org/pub/linux/kernel/v3.x/linux-3.10.84.tar.xz
  • MIPS: LINUX_HEADERS_URL=https://kernel.org/pub/linux/kernel/v2.6/longterm/v2.6.32/linux-2.6.32.67.tar.xz
• kernels:
  • ARM: firmadyne-v3.10.92
  • MIPS: firmadyne-v2.6.32.68 without e2b9f315547ea50a65baad4899a4780078ab273e and 26bb3636c987fc7e145af73ddea6c10fa93bdae9
• console: c36ae8553fa4e9c82e8a65752906641d81c2360c
• extractor: 5520c64bfa8554c5c17ab671aaed0fdeec91bf19
• libnvram: b60e7d4d576b39dd46107058adb635d43e80e00d
• qemu-linaro: 4753f5e8126a00cc0a8559bfd9b47d6340903323
• binwalk: f2ce2992695fae5477c46980148c89e9c91a5cce
  • jefferson: 090a33be0be4aac8eee8d825447c0eb18dc8b51a
  • sasquatch: 287e4a8e059d3ee7a5f643211fcf00c292cd6f4d