The Neighborhood Discovery Watch daemon maps global scope temporary IPv6 addresses to recognizable names in local DNS databases, so that in tools like iftop, nmap, netstat, etc... hostnames are shown even when machines instead of a sea of temporary addresses. The daemon logs its actions to syslog, so that records can be maintained for long term maintenance.

If you are using Active Directory on a corporate network, and only PC's that join the domain properly are in use, then this daemon is not useful to you. If your network has many different operating systems on it (mac, linux, android, ios) that do not necessarily get plugged in by admins (little physical security) and you need to inventory things to help you get a handle on what is plugged in, and "their" stuff has to work, then this is a reasonably unobtrusive way to have an idea what is being used.

It is good practice to statically assign addresses to things on the network so that when you use tools like iftop, or netstat, you have some idea why given exchanges are taking place. You will be able to identify which devices are active, and if their MAC's are unknown, you can at least ask a few questions such as via nmap, to add them to the known list. It allows building an network inventory.

In IPv4 networks where stricter management is wanted, addresses are given out by the Dynamic Host Configuration Protocol (DHCP.) In IPv6, Stateless Address AutoConfiguration (SLAAC) was originally supposed to replace DHCP, but it turns out that SLAAC did not really do the same thing, so people wanted DHCP back, and they started work on DHCP for IPv6 (DHCPv6.) DHCPv6 initially had a number of gaps, and the implementations have been evolving to fix them. The result is that DHCPv6 does not work reliably with a wide variety of end point devices today. SLAAC is what "just works." With SLAAC, the network guesses addresses, whereas DHCP, in managed networks, they can be assigned.

When using SLAAC, there are "privacy extensions" that change the addresses used by hosts every few hours to prevent tracking of equipment globally. For local network security and management however, it is very practical to know which end points are using which addresses, at a given time.

While it is great to have the addresses mapped to human readable names, it is cumbersome to map them to the ordinary, permanent addresses, as this can cause problems when temporary addresses expire. So a suffix is used to identify them: "anon" by default.

This daemon reads the router advertisements to determine what network it is attached to, then it watches neighborhood discovery protocol messages used by end points to claim addresses, and registers the names claimed into forward and reverse DNS records for the domain and subnet.

The purpose here is to understand your own network, not let your users be tracked by others. While there is nothing to force it, it is assumed that DNS is split-horizon and that the zones updated are only internally visible, as sharing the temporary addresses publically may allow others to track end-point device use on your network.

Since neighborhood discovery is the same protocol used to be able to communicate over IPv6 at all, the daemon should work in any network with any combination of end points, and should be difficult to avoid or subvert.

If an unknown end-point connects to the network, the daemon will create DNS entries for it, so that folks can do further auditing work to identify it.

• clean up of records is not fully thought out yet. things get cleaned out by si46ib9d whenever static changes made. have dns_clean which only removes reverse addresses. need to add fwd as well.
• not trying to find those trying to use other devices' IP's yet. (ie. mac/host mismatch.)
• should link level addresses be registered?
• worry about mac spoofing? same as nbd or arp today... don't see why. if they use a different MAC they will be given an UNKNOWN, but remaint identifiable by MAC, would have to rotate MACs.
• should we identify static addresses, and register those without the suffix? avoid need to create any host entries in IPv6, just create them on the fly as MACs show up.

on ubuntu 12.04 or Debian 7.1:

python < 3

apt-get install python-pcapy python-dpkt python-dnspython

mkdir /etc/ndwatch/

cp ndwatch.conf.sample /etc/ndwatch/ndwatch.conf

You need to have a working IPv6 network, which usually means that SLAAC (Stateless Address Auto Configuration) is used to assign addresses. In an IPv6 network without DHCPv6, a router needs to be sending advertisements out.

You also need a fully configured DNS for dynamic updates, including the IPv6 reverse zone that will be updated. For a small network starting from scratch, si46ib9d ( https://github.com/petersilva/si46ib9d ) is what I use (sets up ipv4 and ipv6 bind9 dns, as well as dhcp server for ipv4, and the configuration file for ndwatch from a single configuration file.) still a little unix filtering on a dhcp configuration file should give you mac to host name mappings.

Edit /etc/ndwatch/ndwatch.conf

domain <set your domain.>
# <setup for dynamic updates to your DNS.>
dnsmaster <the master dns server host.>
dnskey  
	-- obtain user name and key 

for each host on the net
host <name preferrd in DNS> mac-address

put that in this file.

If you assign IPv4 addresses to machines via dhcp, then bring that information over into host declarations.

python ndwatch.py >watch.out 2>&1 &

Start up the daemon, and it should create reverse records for known MACs that point to the same server. there is also a sample init script and crontab entry included.

Once it is set up, one can refer to all hosts by their host names, and administer network traffic rules by applying them to all the addresses for each host. An example of blocking a series of hosts is given by the block_hosts.sample.

• added records, but cleanup of old ones is incomplete. not a problem if used in conjunction with si46ib9d which re-writes the entire db every time there is a change to permanent addresses.
• did not bother tracking why, but it crashes after some undefined period of time. you need to install the cronjob to restart it. the cronjob checks every hour and restarts if it has died. Since the neighbor table is still good within an hour or two, no addresses should be missed. actually, this might be fixed... found some link address patterns I wasn't expecting... have to see after a while.