An LED scoreboard for Major League Baseball. Displays a live scoreboard for your team's game on that day.
Requires a Raspberry PI and an LED board hooked up via the GPIO pins.
It can display live games in action, and optionally rotate every 15 seconds through each game of the day.
The board refreshes the list of games every 15 minutes.
Sometimes you don't get baseball though :(
If a game hasn't started yet, a pregame screen will be displayed with the probable starting pitchers.
It can display standings for the provided division. Since the 32x32 board is too small to display wins and losses together, the wins and losses are alternated on the board every 5 seconds.
Note: The installation steps are very much a WIP as I'm having more people test this out. This will update as more people adopt this software.
git clone --recursive https://github.com/ajbowler/mlb-led-scoreboard
cd matrix/bindings/python
Then follow the instructions in that directory. The README there will guide you through building the necessary binaries to run the Python samples (stuff like pulsing colors, running text on the screen, etc.)
You cannot run this program until you have built the RGBMatrix binaries per the instructions in that README.
A very important note not to forget is setting up the hardware you use. Make sure to edit the Makefile in the lib/ directory to the right hardware description. I'm using adafruit-hat since I built this with an Adafruit HAT.
Then do the following:
cd .. # you should be in matrix/bindings now
sudo pip install -e python/
cd ../../ # you should be in mlb-led-scoreboard/ now
sudo pip install mlbgame
make
Basically, you're going to go back above the python binding directory, then run a pip install on that directory to create your own rgbmatrix module. Then go back up to the project directory and install mlbgame, the API this software uses to get baseball stats.
Install anything else your Pi yells at you for. I needed python-dev and a few native extensions for other stuff. Outside of scope of this project but this should at least help point people in the right direction.
sudo python main.py Running as root is 100% an absolute must, or the matrix won't render.
A default config.json.example file is included for reference. Copy this file to config.json and modify the values as needed.
"preferred_team" String Pick a team to display a game for. Example: "Cubs"
"preferred_division" String Pick a division to display standings for when display_standings is true. Example: "NL Central"
"display_standings" Bool Display standings for the provided preferred_division.
"rotate_games" Bool Rotate through each game of the day every 15 seconds.
"debug_enabled" Bool Game and other debug data is written to your console.
You can configure your LED matrix with the same flags used in the rpi-rgb-led-matrix library. More information on these arguments can be found in the library documentation.
--led-rows Display rows. 16 for 16x32, 32 for 32x32. (Default: 32)
--led-cols Panel columns. Typically 32 or 64. (Default: 32)
--led-chain Daisy-chained boards. (Default: 1)
--led-parallel For Plus-models or RPi2: parallel chains. 1..3. (Default: 1)
--led-pwm-bits Bits used for PWM. Range 1..11. (Default: 11)
--led-brightness Sets brightness level. Range: 1..100. (Default: 100)
--led-gpio-mapping Hardware Mapping: regular, adafruit-hat, adafruit-hat-pwm
--led-scan-mode Progressive or interlaced scan. 0 = Progressive, 1 = Interlaced. (Default: 1)
--led-pwm-lsb-nanosecond Base time-unit for the on-time in the lowest significant bit in nanoseconds. (Default: 130)
--led-show-refresh Shows the current refresh rate of the LED panel.
--led-slowdown-gpio Slow down writing to GPIO. Range: 0..4. (Default: 1)
--led-no-hardware-pulse Don't use hardware pin-pulse generation.
--led-rgb-sequence Switch if your matrix has led colors swapped. (Default: RGB)
--led-row-addr-type 0 = default; 1 = AB-addressed panels. (Default: 0)
--led-multiplexing Multiplexing type: 0 = direct; 1 = strip; 2 = checker; 3 = spiral. (Default: 0)
This project relies on two libraries:
MLBGame is the Python library used for retrieving live game data.
rpi-rgb-led-matrix is the library used for making everything work with the LED board and is included as a submodule, so when cloning, make sure you add --recursive.
The scoreboard is dependent on MLB having their data correct and up to date. If you see any weird data such as wrong pitches or scores or whatever else, MLB is drunk.
If you run into any issues and have steps to reproduce, open an issue. If you have a feature request, open an issue. If you want to contribute a small to medium sized change, open a pull request. If you want to contribute a new feature, open an issue first before opening a PR.
If you just want to talk, join the Slack channel, see the badge at the top of the README