Beispiel #1
0
def sort_edges_into_order(occedgelist, isclosed=False):
    from OCC.TopoDS import topods
    from OCC.TopExp import topexp
    from OCC.BRep import BRep_Tool
    from OCC.ShapeAnalysis import ShapeAnalysis_WireOrder
    from OCC.Precision import precision

    sawo_statusdict = {
        0: "all edges are direct and in sequence",
        1: "all edges are direct but some are not in sequence",
        2: "unresolved gaps remain",
        -1: "some edges are reversed, but no gaps remain",
        -2: "some edges are reversed and some gaps remain",
        -10: "failure on reorder"
    }

    mode3d = True
    SAWO = ShapeAnalysis_WireOrder(mode3d, precision.PConfusion())

    for occedge in occedgelist:
        V1 = topexp.FirstVertex(topods.Edge(occedge))
        V2 = topexp.LastVertex(topods.Edge(occedge))
        pnt1 = BRep_Tool().Pnt(V1)
        pnt2 = BRep_Tool().Pnt(V2)
        SAWO.Add(pnt1.XYZ(), pnt2.XYZ())
        SAWO.SetKeepLoopsMode(True)

    SAWO.Perform(isclosed)
    #print "SAWO.Status()", SAWO.Status()
    if not SAWO.IsDone():
        raise RuntimeError, "build wire: Unable to reorder edges: \n" + sawo_statusdict[
            SAWO.Status()]
    else:
        if SAWO.Status() not in [0, -1]:
            pass  # not critical, wirebuilder will handle this
        SAWO.SetChains(precision.PConfusion())
        sorted_edge2dlist = []
        #print "Number of chains: ", SAWO.NbChains()
        for i in range(SAWO.NbChains()):
            sorted_edges = []
            estart, eend = SAWO.Chain(i + 1)
            #print "Number of edges in chain", i, ": ", eend - estart + 1
            if (eend - estart + 1) == 0:
                continue
            for j in range(estart, eend + 1):
                idx = abs(SAWO.Ordered(j))
                edge2w = occedgelist[idx - 1]
                if SAWO.Ordered(j) < 0:
                    edge2w.Reverse()
                sorted_edges.append(edge2w)

            sorted_edge2dlist.append(sorted_edges)

    return sorted_edge2dlist
Beispiel #2
0
def arrange_edges_2_wires(occedgelist, isclosed=False):
    from OCC.TopoDS import topods
    from OCC.TopExp import topexp
    from OCC.BRep import BRep_Tool
    from OCC.ShapeAnalysis import ShapeAnalysis_WireOrder
    from OCC.Precision import precision
    from OCC.BRepBuilderAPI import BRepBuilderAPI_WireDone, BRepBuilderAPI_EmptyWire, BRepBuilderAPI_DisconnectedWire, BRepBuilderAPI_NonManifoldWire

    wb_errdict = {
        BRepBuilderAPI_WireDone: "No error",
        BRepBuilderAPI_EmptyWire: "Empty wire",
        BRepBuilderAPI_DisconnectedWire: "disconnected wire",
        BRepBuilderAPI_NonManifoldWire: "non-manifold wire"
    }

    sawo_statusdict = {
        0: "all edges are direct and in sequence",
        1: "all edges are direct but some are not in sequence",
        2: "unresolved gaps remain",
        -1: "some edges are reversed, but no gaps remain",
        -2: "some edges are reversed and some gaps remain",
        -10: "failure on reorder"
    }

    mode3d = True
    SAWO = ShapeAnalysis_WireOrder(mode3d, precision.PConfusion())

    for edge in occedgelist:
        V1 = topexp.FirstVertex(topods.Edge(edge))
        V2 = topexp.LastVertex(topods.Edge(edge))
        pnt1 = BRep_Tool().Pnt(V1)
        pnt2 = BRep_Tool().Pnt(V2)
        SAWO.Add(pnt1.XYZ(), pnt2.XYZ())
        SAWO.SetKeepLoopsMode(True)

    SAWO.Perform(isclosed)
    #print "SAWO.Status()", SAWO.Status()
    if not SAWO.IsDone():
        raise RuntimeError, "build wire: Unable to reorder edges: \n" + sawo_statusdict[
            SAWO.Status()]
    else:
        if SAWO.Status() not in [0, -1]:
            pass  # not critical, wirebuilder will handle this
        SAWO.SetChains(precision.PConfusion())
        wirelist = []
        #print "Number of chains: ", SAWO.NbChains()

        for i in range(SAWO.NbChains()):
            wirebuilder = BRepBuilderAPI_MakeWire()
            estart, eend = SAWO.Chain(i + 1)
            #print "Number of edges in chain", i, ": ", eend - estart + 1
            if (eend - estart + 1) == 0:
                continue
            for j in range(estart, eend + 1):
                idx = abs(
                    SAWO.Ordered(j)
                )  # wirebuilder = s_addToWireBuilder(wirebuilder, edgelist[idx-1])
                edge2w = occedgelist[idx - 1]
                wirebuilder.Add(edge2w)
                if wirebuilder is None:
                    raise RuntimeError, " build wire: Error adding edge number " + str(
                        j + 1) + " to Wire number " + str(i)
                    err = wirebuilder.Error()
                    if err != BRepBuilderAPI_WireDone:
                        raise RuntimeError, "Overlay2D: build wire: Error adding edge number " + str(
                            j + 1) + " to Wire number " + str(
                                i) + ": \n" + wb_errdict[err]
                        try:
                            wirebuilder.Build()
                            aWire = wirebuilder.Wire()
                            wirelist.append(aWire)
                        except Exception, err:
                            raise RuntimeError, "Overlay2D: build wire: Creation of Wire number " + str(
                                i) + " from edge(s) failed. \n" + str(err)

            wirebuilder.Build()
            aWire = wirebuilder.Wire()
            wirelist.append(aWire)