def open(self, port_index=0):
"Connect to bus adapter"
_i2c_bus.open(self)
# TODO, need to support multiple instances of bus_aadvark_i2c with single adapter.
# This way it is possible to connect multiple i2c slaves to same bus.
self._handle = aa.aa_open(port_index)
if self._handle < 0:
if (self._handle == -7):
raise BusException(
'bus_aadvark_i2c.open failed with error code %d (Aardvark disconnected)'
% self._handle)
else:
raise BusException(
'bus_aadvark_i2c.open failed with error code %d' %
self._handle)
# IO direction now all input, do this before AA_CONFIG_GPIO_I2C
aa.aa_gpio_direction(
self._handle,
int(evkit_config.get('aardvark_i2c', 'aa_gpio_direction'), 16))
## select pullup or floating
#aa.aa_gpio_pullup(self._handle, aa.AA_GPIO_SCK | aa.AA_GPIO_MOSI) # pullup for gpio lines
aa.aa_gpio_pullup(
self._handle,
int(evkit_config.get('aardvark_i2c', 'aa_gpio_pullup'), 16))
#todo slave address selection GPIO to output
# Ensure that the I2C subsystem is enabled
aa.aa_configure(self._handle, aa.AA_CONFIG_GPIO_I2C)
# Enable the I2C bus pullup resistors (2.2k resistors).
# This command is only effective on v2.0 hardware or greater.
# The pullup resistors on the v1.02 hardware are enabled by default.
aa.aa_i2c_pullup(
self._handle,
self.aa_i2c_pullup[evkit_config.get('aardvark_i2c',
'aa_i2c_pullup')])
# Power the board using the Aardvark adapter's power supply.
# This command is only effective on v2.0 hardware or greater.
# The power pins on the v1.02 hardware are not enabled by default.
aa.aa_target_power(
self._handle,
self.aa_target_power[evkit_config.get('aardvark_i2c',
'aa_target_power')])
# Set the bitrate
requested = self._bitrate
self._bitrate = aa.aa_i2c_bitrate(self._handle, self._bitrate)
if requested != self._bitrate:
logger.warning('Bitrate set to %d kHz. Wanted to set %d kHz' %
(self._bitrate, requested))
def open(self, port_index=0):
assert evkit_config.get(
'spi', 'ss_polarity') in ['ACTIVE_LOW', 'ACTIVE_HIGH']
assert evkit_config.get('spi', 'bitorder') in ['MSB', 'LSB']
_spi_bus.open(self)
self._handle = aa.aa_open(port_index)
if self._handle < 0:
if (self._handle == -7):
raise BusException(
'bus_aadvark_spi.open failed with error code %d (Aardvark disconnected)'
% self._handle)
else:
raise BusException(
'bus_aadvark_spi.open failed with error code %d' %
self._handle)
aa.aa_gpio_direction(self._handle,
int(
evkit_config.get('aardvark_spi',
'aa_gpio_direction'),
16)) # IO direction
## select pullup or floating
#aa.aa_gpio_pullup(self._handle, aa.AA_GPIO_SCL | aa.AA_GPIO_SDA) # pullup
aa.aa_gpio_pullup(
self._handle,
int(evkit_config.get('aardvark_spi', 'aa_gpio_pullup'), 16))
aa.aa_configure(self._handle,
aa.AA_CONFIG_SPI_GPIO) # SPI subsystem is enabled
aa.aa_target_power(
self._handle,
self._aa_target_power[evkit_config.get('aardvark_spi',
'aa_target_power')])
aa.aa_spi_configure(
self._handle, self._cpol, self._cpha,
self._bitorder[evkit_config.get('spi', 'bitorder')])
aa.aa_spi_master_ss_polarity(
self._handle,
self._ss_polarity[evkit_config.get('spi', 'ss_polarity')])
requested = self._bitrate
self._bitrate = aa.aa_spi_bitrate(self._handle,
self._bitrate) # Set the bitrate
if requested != self._bitrate:
logger.warning(
"Warning Bitrate set to %d kHz. Wanted to set %d kHz" %
(self._bitrate, requested))
def spi_mode(self, value):
if not isinstance(value, bool):
raise TypeError("invalid SPI mode state: %s (must be boolean)" % value)
config = aardvark_py.aa_configure(self._aardvark_handle, aardvark_py.AA_CONFIG_QUERY)
_validate_status(config)
if value:
config |= aardvark_py.AA_CONFIG_SPI_MASK
else:
config &= ~aardvark_py.AA_CONFIG_SPI_MASK
current_config = aardvark_py.aa_configure(self._aardvark_handle, config)
_validate_status(current_config)
if not (config == current_config):
raise AardvarkError("unable to configure Aardvark for SPI mode")
def spi_mode(self, value):
if not isinstance(value, bool):
raise TypeError("invalid SPI mode state: %s (must be boolean)" %
value)
config = aardvark_py.aa_configure(self._aardvark_handle,
aardvark_py.AA_CONFIG_QUERY)
_validate_status(config)
if value:
config |= aardvark_py.AA_CONFIG_SPI_MASK
else:
config &= ~aardvark_py.AA_CONFIG_SPI_MASK
current_config = aardvark_py.aa_configure(self._aardvark_handle,
config)
_validate_status(current_config)
if not (config == current_config):
raise AardvarkError("unable to configure Aardvark for SPI mode")
def spi_mode(self):
"""Enable or disable SPI mode on the Aardvark adapter.
True - Enable SPI mode
False - Disable SPI mode
If SPI is disabled, the pins can be used as GPIO instead.
"""
config = aardvark_py.aa_configure(self._aardvark_handle, aardvark_py.AA_CONFIG_QUERY)
_validate_status(config)
return bool(config & aardvark_py.AA_CONFIG_SPI_MASK)
def spi_mode(self):
"""Enable or disable SPI mode on the Aardvark adapter.
True - Enable SPI mode
False - Disable SPI mode
If SPI is disabled, the pins can be used as GPIO instead.
"""
config = aardvark_py.aa_configure(self._aardvark_handle,
aardvark_py.AA_CONFIG_QUERY)
_validate_status(config)
return bool(config & aardvark_py.AA_CONFIG_SPI_MASK)
def __init__(self, uid = None): (num, ports, unique_ids) = aa_py.aa_find_devices_ext(16, 16) if num > 0: ix = 0 if uid: if uid in unique_ids: ix = unique_ids.index(uid) port = ports[ix] if port & aa_py.AA_PORT_NOT_FREE: raise ValueError else: raise ValueError else: while ix < num: port = ports[ix] if port & aa_py.AA_PORT_NOT_FREE: ix += 1 continue break if ix == num: print "No Free Device" raise IndexError else: print "No devices connected" raise IndexError self.aa = aa_py.aa_open(port) self.get_serial_number() aa_py.aa_configure(self.aa, aa_py.AA_CONFIG_GPIO_I2C) aa_py.aa_configure(self.aa, aa_py.AA_TARGET_POWER_NONE) aa_py.aa_configure(self.aa, aa_py.AA_CONFIG_GPIO_I2C)
def __init__(self): """Initialize a new instance of the Bus class. This will access the Aardvark API and open the first available Aardvark USB device. If no device is available, an exception will be raised. """ self._port = _find_aardvark() self._open = False self._handle = _check_result(api.aa_open(self._port)) self._open = True _check_result(api.aa_configure(self._handle, api.AA_CONFIG_GPIO_I2C)) # AA_CONFIG_SPI_I2C _check_result(api.aa_i2c_pullup(self._handle, api.AA_I2C_PULLUP_BOTH)) _check_result(api.aa_i2c_bitrate(self._handle, 100)) _check_result(api.aa_gpio_set(self._handle, 0x00)) # Initialize to zeros _check_result(api.aa_gpio_direction(self._handle, 0xFF)) # All outputs
def __init__(self):
"""Initialize a new instance of the Bus class. This will access the
Aardvark API and open the first available Aardvark USB device. If no
device is available, an exception will be raised.
"""
self._port = _find_aardvark()
self._open = False
self._handle = _check_result(api.aa_open(self._port))
self._open = True
_check_result(api.aa_configure(
self._handle, api.AA_CONFIG_GPIO_I2C)) # AA_CONFIG_SPI_I2C
_check_result(api.aa_i2c_pullup(self._handle, api.AA_I2C_PULLUP_BOTH))
_check_result(api.aa_i2c_bitrate(self._handle, 100))
_check_result(api.aa_gpio_set(self._handle,
0x00)) # Initialize to zeros
_check_result(api.aa_gpio_direction(self._handle, 0xFF)) # All outputs
def configure_aardvark():
"""
Function to configure the aardvark for pySCPI operation if there is one
available.
@return (aardvark_py.aardvark) The handle of the aardvark to be used
'None' if there is not one available
"""
# define the handle to return
Aardvark_in_use = None
# find all connected aardvarks
AA_Devices = aardvark_py.aa_find_devices(1)
# define a port mask
Aardvark_port = 8<<7
# assume that an aardvark can be found until proved otherwise
Aardvark_free = True
# Check if there is an Aardvark present
if (AA_Devices[0] < 1):
# there is no aardvark to be found
print '*** No Aardvark is present ***'
Aardvark_free = False
else:
# there is an aardvark connected to select the first one if there
# are many
Aardvark_port = AA_Devices[1][0]
# end if
# If there is an Aardvark there is it free?
if Aardvark_port >= 8<<7 and Aardvark_free:
# the aardvark is not free
print '*** Aardvark is being used, '\
'disconnect other application or Aardvark device ***'
# close the aardvark
aardvark_py.aa_close(Aardvark_port)
Aardvark_free = False
elif Aardvark_free:
# Aardvark is available so configure it
# open the connection with the aardvark
Aardvark_in_use = aardvark_py.aa_open(Aardvark_port)
# set it up in teh mode we need for pumpkin modules
aardvark_py.aa_configure(Aardvark_in_use,
aardvark_py.AA_CONFIG_SPI_I2C)
# default to both pullups on
aardvark_py.aa_i2c_pullup(Aardvark_in_use,
aardvark_py.AA_I2C_PULLUP_BOTH)
# set the bit rate to be the default
aardvark_py.aa_i2c_bitrate(Aardvark_in_use, Bitrate)
# free the bus
aardvark_py.aa_i2c_free_bus(Aardvark_in_use)
# delay to allow the config to be registered
aardvark_py.aa_sleep_ms(200)
print "Starting Aardvark communications\n"
# end if
return Aardvark_in_use
#==========================================================================
# MAIN PROGRAM
#==========================================================================
port = 0
# Open the device.
handle = aa_open(port)
if (handle <= 0):
print "Unable to open Aardvark device on port %d" % port
print "Error code = %d" % handle
sys.exit()
# Enable I2C subsystem.
aa_configure(handle, AA_CONFIG_SPI_I2C)
# Enable the I2C bus pullup resistors (2.2k resistors).
#aa_i2c_pullup(handle, AA_I2C_PULLUP_BOTH)
# Power the board using the Aardvark adapter's power supply.
aa_target_power(handle, AA_TARGET_POWER_BOTH)
# Set the bitrate.
aa_i2c_bitrate(handle, I2C_BITRATE)
# positive tests
if get_version(handle) <= 0:
exit()
exit()