def regsetup():
print("ran setup")
global alarmTime
global wakeSounds
global sensor
global i2c
global dist
global stopMusic
alarmTime = int(input("enter wake up time eg. 6, 15 for 6:25 "))
wakeSounds = input("what do you want me to say? ")
i2c = busio.I2C(board.SCL, board.SDA)
sensor = adafruit_vcnl4010.VCNL4010(i2c)
dist = sensor.proximity
stopMusic = False
# SPDX-FileCopyrightText: 2017 Tony DiCola for Adafruit Industries
# SPDX-License-Identifier: MIT
# Simple demo of the VCNL4010 proximity and light sensor.
# Will print the proximity and ambient light every second.
import time
import board
import busio
import adafruit_vcnl4010
# Initialize I2C bus and VCNL4010 module.
i2c = busio.I2C(board.SCL, board.SDA)
sensor = adafruit_vcnl4010.VCNL4010(i2c)
# You can optionally adjust the sensor LED current. The default is 200mA
# which is the maximum value. Note this is only set in 10mA increments.
# sensor.led_current_mA = 120 # Set 120 mA LED current
# You can also adjust the measurement frequency for the sensor. The default
# is 390.625 khz, but these values are possible to set too:
# - FREQUENCY_3M125: 3.125 Mhz
# - FREQUENCY_1M5625: 1.5625 Mhz
# - FREQUENCY_781K25: 781.25 Khz
# - FREQUENCY_390K625: 390.625 Khz (default)
# sensor.frequency = adafruit_vcnl4010.FREQUENCY_3M125 # 3.125 Mhz
# Main loop runs forever printing the proximity and light level.
while True:
proximity = sensor.proximity # Proximity has no units and is a 16-bit
help="Delete images after classifcation if true")
args = parser.parse_args()
_USE_TEST_MODE = args.test
_USE_BLOB_STORAGE = args.blobstorage
_DELETE_IMAGES = args.deleteimages
if (_USE_TEST_MODE):
log.info("Starting in TEST Mode")
if (_USE_BLOB_STORAGE):
log.info("Blob Storage Enabled.")
connect_storage_account()
if (_DELETE_IMAGES):
log.info("Deleting images after classification.")
if args.sensor == 'vcnl4010':
log.info("Calibrating VCNL4010 motion sensor")
i2c = busio.I2C(board.SCL, board.SDA)
vcnl = adafruit_vcnl4010.VCNL4010(i2c)
percent = calibratePSensor(vcnl)
flash_led = LED(23) #LED connected on GPIO pin 23
if args.sensor == 'vcnl4040':
log.info("Calibrating VCNL4040 motion sensor")
i2c = busio.I2C(board.SCL, board.SDA)
vcnl = adafruit_vcnl4040.VCNL4040(i2c)
percent = calibratePSensor(vcnl)
flash_led = LED(23) #LED connected on GPIO pin 23
if args.sensor == 'motion':
log.info("Using Motion Sensor")
move_sensor = MotionSensor(
17) #Motion Sensor control connected to GPIO pin 17
red_led = LED(18) #LED connected to GPIO pin 18
try:
def _setup(neopixels):
i2c = busio.I2C(board.SCL, board.SDA)
prox_sensor = adafruit_vcnl4010.VCNL4010(i2c)
pixels = neopixel.NeoPixel(*neopixels)
return i2c, prox_sensor, pixels
