def bar(width, thick, diameter, tolerance, amount=0, stem=1, twist=False, tneck=0.5, tthick=0.01, twist_keep=False,
twist_line=False, twist_line_amount=2, which='MF'):
# width = length of the bar
# thick = thickness of the bar
# diameter = diameter of the tool for joint creation
# tolerance = Tolerance in the joint
# amount = amount of fingers in the joint 0 means auto generate
# stem = amount of radius the stem or neck of the joint will have
# twist = twist lock addition
# tneck = percentage the twist neck will have compared to thick
# tthick = thicknest of the twist material
# Which M,F, MF, MM, FF
global DT
if amount == 0:
amount = round(thick / ((4 + 2 * (stem - 1)) * diameter * DT)) - 1
bpy.ops.curve.simple(align='WORLD', location=(0, 0, 0), rotation=(0, 0, 0), Simple_Type='Rectangle',
Simple_width=width, Simple_length=thick, use_cyclic_u=True, edit_mode=False)
simple.active_name('tmprect')
fingers(diameter, tolerance, amount, stem=stem)
if which == 'MM' or which == 'M' or which == 'MF':
simple.rename('fingers', '_tmpfingers')
simple.rotate(-math.pi / 2)
simple.move(x=width / 2)
simple.rename('tmprect', '_tmprect')
simple.union('_tmp')
simple.active_name("tmprect")
twistm('tmprect', thick, diameter, tolerance, twist, tneck, tthick, -math.pi / 2,
x=width / 2, twist_keep=twist_keep)
twistf('receptacle', thick, diameter, tolerance, twist, tneck, tthick, twist_keep=twist_keep)
simple.rename('receptacle', '_tmpreceptacle')
if which == 'FF' or which == 'F' or which == 'MF':
simple.rotate(-math.pi / 2)
simple.move(x=-width / 2)
simple.rename('tmprect', '_tmprect')
simple.difference('_tmp', '_tmprect')
simple.active_name("tmprect")
if twist_keep:
simple.make_active('twist_keep_f')
simple.rotate(-math.pi / 2)
simple.move(x=-width / 2)
simple.remove_multiple("_") # Remove temporary base and holes
simple.remove_multiple("fingers") # Remove temporary base and holes
if twist_line:
joinery.twist_line(thick, tthick, tolerance, tneck, twist_line_amount, width)
if twist_keep:
simple.duplicate()
simple.active_name('tmptwist')
simple.difference('tmp', 'tmprect')
simple.rename('tmprect', 'Puzzle_bar')
simple.remove_multiple("tmp") # Remove temporary base and holes
simple.make_active('Puzzle_bar')
def twist_separator_slot(length,
thickness,
finger_play=0.00005,
percentage=0.5):
simple.add_rectangle(thickness + finger_play / 2, length, center_y=False)
simple.move(y=((length * percentage - finger_play / 2) / 2))
simple.duplicate()
simple.mirrory()
simple.join_multiple('simple_rectangle')
simple.active_name('_separator_slot')
def arcbararc(length, radius, thick, angle, angleb, diameter, tolerance, amount=0, stem=1, twist=False,
tneck=0.5, tthick=0.01, which='MF', twist_keep=False, twist_line=False, twist_line_amount=2):
# length is the total width of the segments including 2 * radius and thick
# radius = radius of the curve
# thick = thickness of the bar
# angle = angle of the female part
# angleb = angle of the male part
# diameter = diameter of the tool for joint creation
# tolerance = Tolerance in the joint
# amount = amount of fingers in the joint 0 means auto generate
# stem = amount of radius the stem or neck of the joint will have
# twist = twist lock addition
# tneck = percentage the twist neck will have compared to thick
# tthick = thicknest of the twist material
# which = which joint to generate, Male Female MaleFemale M, F, MF
length -= (radius * 2 + thick) # adjust length to include 2x radius + thick
# generate base rectangle
bpy.ops.curve.simple(align='WORLD', location=(0, 0, 0), rotation=(0, 0, 0), Simple_Type='Rectangle',
Simple_width=length * 1.005, Simple_length=thick, use_cyclic_u=True, edit_mode=False)
simple.active_name("tmprect")
# Generate male section and join to the base
if which == 'M' or which == 'MF':
arc(radius, thick, angleb, diameter, tolerance, amount=amount, stem=stem, twist=twist, tneck=tneck,
tthick=tthick, which='M')
simple.move(x=length / 2)
simple.active_name('tmp_male')
simple.select_multiple('tmp')
bpy.ops.object.curve_boolean(boolean_type='UNION')
simple.active_name('male')
simple.remove_multiple('tmp')
simple.rename('male', 'tmprect')
# Generate female section and join to base
if which == 'F' or which == 'MF':
arc(radius, thick, angle, diameter, tolerance, amount=amount, stem=stem, twist=twist, tneck=tneck,
tthick=tthick, which='F')
simple.move(x=-length / 2)
simple.active_name('tmp_receptacle')
simple.union('tmp')
simple.active_name('tmprect')
if twist_line:
joinery.twist_line(thick, tthick, tolerance, tneck, twist_line_amount, length)
if twist_keep:
simple.duplicate()
simple.active_name('tmptwist')
simple.difference('tmp', 'tmprect')
simple.active_name('arcBarArc')
simple.make_active('arcBarArc')
def rack(mm_per_tooth=0.01,
number_of_teeth=11,
height=0.012,
pressure_angle=0.3488,
backlash=0.0,
hole_diameter=0.003175,
tooth_per_hole=4):
simple.deselect()
pi = math.pi
mm_per_tooth *= 1000
a = mm_per_tooth / pi # addendum
t = (a * math.sin(pressure_angle)
) # tooth side is tilted so top/bottom corners move this amount
a /= 1000
mm_per_tooth /= 1000
t /= 1000
shapely_gear = Polygon([(-mm_per_tooth * 2 / 4 * 1.001, a - height),
(-mm_per_tooth * 2 / 4 * 1.001 - backlash, -a),
(-mm_per_tooth * 1 / 4 + backlash - t, -a),
(-mm_per_tooth * 1 / 4 + backlash + t, a),
(mm_per_tooth * 1 / 4 - backlash - t, a),
(mm_per_tooth * 1 / 4 - backlash + t, -a),
(mm_per_tooth * 2 / 4 * 1.001 + backlash, -a),
(mm_per_tooth * 2 / 4 * 1.001, a - height)])
utils.shapelyToCurve('_tooth', shapely_gear, 0.0)
i = number_of_teeth
while i > 1:
simple.duplicate(x=mm_per_tooth)
i -= 1
simple.union('_tooth')
simple.move(y=height / 2)
if hole_diameter > 0:
bpy.ops.curve.simple(align='WORLD',
location=(mm_per_tooth / 2, 0, 0),
rotation=(0, 0, 0),
Simple_Type='Circle',
Simple_radius=hole_diameter / 2,
shape='3D',
use_cyclic_u=True,
edit_mode=False)
simple.active_name('_hole')
distance = (number_of_teeth - 1) * mm_per_tooth
while distance > tooth_per_hole * mm_per_tooth:
simple.duplicate(x=tooth_per_hole * mm_per_tooth)
distance -= tooth_per_hole * mm_per_tooth
simple.difference('_', '_tooth')
name = 'rack-' + str(round(mm_per_tooth * 1000, 1))
name += '-PA-' + str(round(math.degrees(pressure_angle), 1))
simple.active_name(name)
def finger(diameter, stem=2):
# diameter = diameter of the tool for joint creation
# DT = Bit diameter tolerance
# stem = amount of radius the stem or neck of the joint will have
global DT
RESOLUTION = 12 # Data resolution
cube_sx = diameter * DT * (2 + stem - 1)
cube_ty = diameter * DT
cube_sy = 2 * diameter * DT
circle_radius = diameter * DT / 2
c1x = cube_sx / 2
c2x = cube_sx / 2
c2y = 3 * circle_radius
c1y = circle_radius
bpy.ops.curve.simple(align='WORLD', location=(0, cube_ty, 0), rotation=(0, 0, 0), Simple_Type='Rectangle',
Simple_width=cube_sx, Simple_length=cube_sy, use_cyclic_u=True, edit_mode=False)
bpy.context.active_object.name = "ftmprect"
bpy.ops.curve.simple(align='WORLD', location=(c2x, c2y, 0), rotation=(0, 0, 0), Simple_Type='Ellipse',
Simple_a=circle_radius,
Simple_b=circle_radius, Simple_sides=4, use_cyclic_u=True, edit_mode=False, shape='3D')
bpy.context.active_object.name = "ftmpcirc_add"
bpy.context.object.data.resolution_u = RESOLUTION
bpy.ops.object.origin_set(type='ORIGIN_CURSOR', center='MEDIAN')
simple.duplicate()
simple.mirrorx()
simple.union('ftmp')
simple.rename('ftmp', '_sum')
rc1 = circle_radius
bpy.ops.curve.simple(align='WORLD', location=(c1x, c1y, 0), rotation=(0, 0, 0), Simple_Type='Ellipse',
Simple_a=circle_radius, Simple_b=rc1, Simple_sides=4, use_cyclic_u=True, edit_mode=False,
shape='3D')
bpy.context.active_object.name = "_circ_delete"
bpy.context.object.data.resolution_u = RESOLUTION
bpy.ops.object.origin_set(type='ORIGIN_CURSOR', center='MEDIAN')
simple.duplicate()
simple.mirrorx()
simple.union('_circ')
simple.difference('_', '_sum')
bpy.ops.object.curve_remove_doubles()
simple.rename('_sum', "_puzzle")
def twistf(name, length, diameter, tolerance, twist, tneck, tthick, twist_keep=False):
# add twist lock to receptacle
if twist:
joinery.interlock_twist(length, tthick, tolerance, cx=0, cy=0, rotation=0, percentage=tneck)
simple.rotate(math.pi / 2)
simple.move(y=-tthick / 2 + 2 * diameter + 2 * tolerance)
simple.active_name('xtemptwist')
if twist_keep:
simple.duplicate()
simple.active_name('twist_keep_f')
simple.make_active(name)
simple.active_name('xtemp')
simple.union('xtemp')
simple.active_name(name)
def t(length, thick, diameter, tolerance, amount=0, stem=1, twist=False, tneck=0.5, tthick=0.01, combination='MF',
base_gender='M', corner=False):
if corner:
if combination == 'MF':
base_gender = 'M'
combination = 'f'
elif combination == 'F':
base_gender = 'F'
combination = 'f'
elif combination == 'M':
base_gender = 'M'
combination = 'm'
bar(length, thick, diameter, tolerance, amount=amount, stem=stem, twist=twist, tneck=tneck,
tthick=tthick, which=base_gender)
simple.active_name('tmp')
fingers(diameter, tolerance, amount=amount, stem=stem)
if combination == 'MF' or combination == 'M' or combination == 'm':
simple.make_active('fingers')
simple.move(y=thick / 2)
simple.duplicate()
simple.active_name('tmp')
simple.union('tmp')
if combination == 'M':
simple.make_active('fingers')
simple.mirrory()
simple.active_name('tmp')
simple.union('tmp')
if combination == 'MF' or combination == 'F' or combination == 'f':
simple.make_active('receptacle')
simple.move(y=-thick / 2)
simple.duplicate()
simple.active_name('tmp')
simple.difference('tmp', 'tmp')
if combination == 'F':
simple.make_active('receptacle')
simple.mirrory()
simple.active_name('tmp')
simple.difference('tmp', 'tmp')
simple.remove_multiple('receptacle')
simple.remove_multiple('fingers')
simple.rename('tmp', 't')
simple.make_active('t')
def multiangle(radius, thick, angle, diameter, tolerance, amount=0, stem=1, twist=False,
tneck=0.5, tthick=0.01, combination='MFF'):
# length is the total width of the segments including 2 * radius and thick
# radius = radius of the curve
# thick = thickness of the bar
# angle = angle of the female part
# diameter = diameter of the tool for joint creation
# tolerance = Tolerance in the joint
# amount = amount of fingers in the joint 0 means auto generate
# stem = amount of radius the stem or neck of the joint will have
# twist = twist lock addition
# tneck = percentage the twist neck will have compared to thick
# tthick = thicknest of the twist material
# which = which joint to generate, Male Female MaleFemale M, F, MF
r_exterior = radius + thick / 2
r_interior = radius - thick / 2
height = math.sqrt(r_exterior * r_exterior - radius * radius) + r_interior / 4
bpy.ops.curve.simple(align='WORLD', location=(0, height, 0),
rotation=(0, 0, 0), Simple_Type='Rectangle',
Simple_width=r_interior, Simple_length=r_interior / 2, use_cyclic_u=True,
edit_mode=False, shape='3D')
simple.active_name('tmp_rect')
bpy.ops.curve.simple(align='WORLD', location=(0, 0, 0), rotation=(0, 0, 0), Simple_Type='Circle', Simple_sides=4,
Simple_radius=r_interior, shape='3D', use_cyclic_u=True, edit_mode=False)
simple.move(y=radius * math.tan(angle))
simple.active_name('tmpCircle')
arc(radius, thick, angle, diameter, tolerance, amount=amount, stem=stem, twist=twist, tneck=tneck, tthick=tthick,
which='MF')
simple.active_name('tmp_arc')
if combination == 'MFF':
simple.duplicate()
simple.mirrorx()
elif combination == 'MMF':
arc(radius, thick, angle, diameter, tolerance, amount=amount, stem=stem, twist=twist, tneck=tneck,
tthick=tthick,
which='M')
simple.active_name('tmp_arc')
simple.mirrory()
simple.rotate(math.pi / 2)
simple.union("tmp_")
simple.difference('tmp', 'tmp_')
simple.active_name('multiAngle60')
def twistm(name, length, diameter, tolerance, twist, tneck, tthick, angle, twist_keep=False, x=0, y=0):
# add twist lock to male connector
global DT
if twist:
joinery.interlock_twist(length, tthick, tolerance, cx=0, cy=0, rotation=0, percentage=tneck)
simple.rotate(math.pi / 2)
simple.move(y=-tthick / 2 + 2 * diameter * DT)
simple.rotate(angle)
simple.move(x=x, y=y)
simple.active_name('_twist')
if twist_keep:
simple.duplicate()
simple.active_name('twist_keep_m')
simple.make_active(name)
simple.active_name('_tmp')
simple.difference('_', '_tmp')
simple.active_name(name)
def interlock_twist_separator(length,
thickness,
amount,
spacing,
edge_distance,
finger_play=0.00005,
percentage=0.5,
start='rounded',
end='rounded'):
amount -= 1
base_width = 2 * edge_distance + spacing * amount + thickness
simple.add_rectangle(base_width, length - finger_play * 2, center_x=False)
simple.active_name('_base')
twist_separator_slot(length, thickness, finger_play, percentage)
while amount > 0:
simple.duplicate(x=spacing)
amount -= 1
simple.join_multiple('_separator_slot')
simple.move(x=edge_distance + thickness / 2)
simple.difference('_', '_base')
simple.active_name('twist_separator')
def curved_t(length, thick, radius, diameter, tolerance, amount=0, stem=1, twist=False, tneck=0.5, tthick=0.01,
combination='MF', base_gender='M'):
bar(length, thick, diameter, tolerance, amount=amount, stem=stem, twist=twist, tneck=tneck,
tthick=tthick, which=combination)
simple.active_name('tmpbar')
bpy.ops.curve.simple(align='WORLD', location=(0, 0, 0), rotation=(0, 0, 0), Simple_Type='Rectangle',
Simple_width=3 * radius, Simple_length=thick, use_cyclic_u=True, edit_mode=False)
simple.active_name("tmp_rect")
if base_gender == 'MF':
arc(radius, thick, math.pi / 2, diameter, tolerance,
amount=amount, stem=stem, twist=twist, tneck=tneck, tthick=tthick, which='M')
simple.move(-radius)
simple.active_name('tmp_arc')
arc(radius, thick, math.pi / 2, diameter, tolerance,
amount=amount, stem=stem, twist=twist, tneck=tneck, tthick=tthick, which='F')
simple.move(radius)
simple.mirrory()
simple.active_name('tmp_arc')
simple.union('tmp_arc')
simple.duplicate()
simple.mirrorx()
simple.union('tmp_arc')
simple.difference('tmp_', 'tmp_arc')
else:
arc(radius, thick, math.pi / 2, diameter, tolerance,
amount=amount, stem=stem, twist=twist, tneck=tneck, tthick=tthick, which=base_gender)
simple.active_name('tmp_arc')
simple.difference('tmp_', 'tmp_arc')
if base_gender == 'M':
simple.move(-radius)
else:
simple.move(radius)
simple.duplicate()
simple.mirrorx()
simple.union('tmp')
simple.active_name('curved_t')
def open_curve(line, thick, diameter, tolerance, amount=0, stem=1, twist=False, t_neck=0.5, t_thick=0.01,
twist_amount=1, which='MF', twist_keep=False):
# puts puzzle connectors at the end of an open curve
# optionally puts twist lock connectors at the puzzle connection
# optionally puts twist lock connectors along the open curve
# line = shapely linestring
# thick = thickness of the bar
# diameter = diameter of the tool for joint creation
# tolerance = Tolerance in the joint
# amount = amount of fingers in the joint 0 means auto generate
# stem = amount of radius the stem or neck of the joint will have
# twist = twist lock addition
# twist_amount = twist amount distributed on the curve not counting the joint twist locks
# tneck = percentage the twist neck will have compared to thick
# tthick = thicknest of the twist material
# Which M,F, MF, MM, FF
coords = list(line.coords)
start_angle = joinery.angle(coords[0], coords[1]) + math.pi/2
end_angle = joinery.angle(coords[-1], coords[-2]) + math.pi/2
p_start = coords[0]
p_end = coords[-1]
print('start angle', start_angle)
print('end angle', end_angle)
bpy.ops.curve.simple(align='WORLD', location=(0, 0, 0), rotation=(0, 0, 0), Simple_Type='Rectangle',
Simple_width=thick*2, Simple_length=thick * 2, use_cyclic_u=True, edit_mode=False, shape='3D')
simple.active_name('tmprect')
simple.move(y=thick)
simple.duplicate()
simple.rotate(start_angle)
simple.move(x=p_start[0], y=p_start[1])
simple.make_active('tmprect')
simple.rotate(end_angle)
simple.move(x=p_end[0], y=p_end[1])
simple.union('tmprect')
dilated = line.buffer(thick/2) # expand shapely object to thickness
utils.shapelyToCurve('tmp_curve', dilated, 0.0)
simple.difference('tmp', 'tmp_curve') # truncate curve at both ends with the rectangles
fingers(diameter, tolerance, amount, stem=stem)
simple.make_active('fingers')
simple.rotate(end_angle)
simple.move(x=p_end[0], y=p_end[1])
simple.active_name('tmp_fingers')
simple.union('tmp_')
simple.active_name('tmp_curve')
twistm('tmp_curve', thick, diameter, tolerance, twist, t_neck, t_thick, end_angle, x=p_end[0], y=p_end[1],
twist_keep=twist_keep)
twistf('receptacle', thick, diameter, tolerance, twist, t_neck, t_thick, twist_keep=twist_keep)
simple.rename('receptacle', 'tmp')
simple.rotate(start_angle+math.pi)
simple.move(x=p_start[0], y=p_start[1])
simple.difference('tmp', 'tmp_curve')
if twist_keep:
simple.make_active('twist_keep_f')
simple.rotate(start_angle + math.pi)
simple.move(x=p_start[0], y=p_start[1])
if twist_amount > 0 and twist:
twist_start = line.length / (twist_amount+1)
joinery.distributed_interlock(line, line.length, thick, t_thick, tolerance, twist_amount,
tangent=math.pi/2, fixed_angle=0, start=twist_start, end=twist_start,
closed=False, type='TWIST', twist_percentage=t_neck)
if twist_keep:
simple.duplicate()
simple.active_name('twist_keep')
simple.join_multiple('twist_keep')
simple.make_active('interlock')
simple.active_name('tmp_twist')
simple.difference('tmp', 'tmp_curve')
simple.active_name('puzzle_curve')
def mitre(length, thick, angle, angleb, diameter, tolerance, amount=0, stem=1, twist=False,
tneck=0.5, tthick=0.01, which='MF'):
# length is the total width of the segments including 2 * radius and thick
# radius = radius of the curve
# thick = thickness of the bar
# angle = angle of the female part
# angleb = angle of the male part
# diameter = diameter of the tool for joint creation
# tolerance = Tolerance in the joint
# amount = amount of fingers in the joint 0 means auto generate
# stem = amount of radius the stem or neck of the joint will have
# twist = twist lock addition
# tneck = percentage the twist neck will have compared to thick
# tthick = thicknest of the twist material
# which = which joint to generate, Male Female MaleFemale M, F, MF
# generate base rectangle
bpy.ops.curve.simple(align='WORLD', location=(0, -thick / 2, 0), rotation=(0, 0, 0), Simple_Type='Rectangle',
Simple_width=length * 1.005 + 4 * thick, Simple_length=thick, use_cyclic_u=True,
edit_mode=False,
shape='3D')
simple.active_name("tmprect")
# generate cutout shapes
bpy.ops.curve.simple(align='WORLD', location=(0, 0, 0), rotation=(0, 0, 0), Simple_Type='Rectangle',
Simple_width=4 * thick, Simple_length=6 * thick, use_cyclic_u=True, edit_mode=False,
shape='3D')
simple.move(x=2 * thick)
simple.rotate(angle)
simple.move(x=length / 2)
simple.active_name('tmpmitreright')
bpy.ops.curve.simple(align='WORLD', location=(0, 0, 0), rotation=(0, 0, 0), Simple_Type='Rectangle',
Simple_width=4 * thick, Simple_length=6 * thick, use_cyclic_u=True, edit_mode=False,
shape='3D')
simple.move(x=2 * thick)
simple.rotate(angleb)
simple.move(x=length / 2)
simple.mirrorx()
simple.active_name('tmpmitreleft')
simple.difference('tmp', 'tmprect')
simple.make_active('tmprect')
fingers(diameter, tolerance, amount, stem=stem)
# Generate male section and join to the base
if which == 'M' or which == 'MF':
simple.make_active('fingers')
simple.duplicate()
simple.active_name('tmpfingers')
simple.rotate(angle - math.pi / 2)
h = thick / math.cos(angle)
h /= 2
simple.move(x=length / 2 + h * math.sin(angle), y=-thick / 2)
if which == 'M':
simple.rename('fingers', 'tmpfingers')
simple.rotate(angleb - math.pi / 2)
h = thick / math.cos(angleb)
h /= 2
simple.move(x=length / 2 + h * math.sin(angleb), y=-thick / 2)
simple.mirrorx()
simple.union('tmp')
simple.active_name('tmprect')
# Generate female section and join to base
if which == 'MF' or which == 'F':
simple.make_active('receptacle')
simple.mirrory()
simple.duplicate()
simple.active_name('tmpreceptacle')
simple.rotate(angleb - math.pi / 2)
h = thick / math.cos(angleb)
h /= 2
simple.move(x=length / 2 + h * math.sin(angleb), y=-thick / 2)
simple.mirrorx()
if which == 'F':
simple.rename('receptacle', 'tmpreceptacle2')
simple.rotate(angle - math.pi / 2)
h = thick / math.cos(angle)
h /= 2
simple.move(x=length / 2 + h * math.sin(angle), y=-thick / 2)
simple.difference('tmp', 'tmprect')
simple.remove_multiple('receptacle')
simple.remove_multiple('fingers')
simple.rename('tmprect', 'mitre')
def gear(mm_per_tooth=0.003,
number_of_teeth=5,
hole_diameter=0.003175,
pressure_angle=0.3488,
clearance=0.0,
backlash=0.0,
rim_size=0.0005,
hub_diameter=0.006,
spokes=4):
simple.deselect()
pi = math.pi
p = mm_per_tooth * number_of_teeth / pi / 2 # radius of pitch circle
c = p + mm_per_tooth / pi - clearance # radius of outer circle
b = p * math.cos(pressure_angle) # radius of base circle
r = p - (c - p) - clearance # radius of root circle
t = mm_per_tooth / 2 - backlash / 2 # tooth thickness at pitch circle
k = -gear_iang(
b, p
) - t / 2 / p # angle to where involute meets base circle on each side of tooth
shapely_gear = Polygon([(0, 0),
gear_polar(r,
k if r < b else -pi / number_of_teeth),
gear_q7(0, r, b, c, k, 1),
gear_q7(0.1, r, b, c, k, 1),
gear_q7(0.2, r, b, c, k, 1),
gear_q7(0.3, r, b, c, k, 1),
gear_q7(0.4, r, b, c, k, 1),
gear_q7(0.5, r, b, c, k, 1),
gear_q7(0.6, r, b, c, k, 1),
gear_q7(0.7, r, b, c, k, 1),
gear_q7(0.8, r, b, c, k, 1),
gear_q7(0.9, r, b, c, k, 1),
gear_q7(1.0, r, b, c, k, 1),
gear_q7(1.0, r, b, c, k, -1),
gear_q7(0.9, r, b, c, k, -1),
gear_q7(0.8, r, b, c, k, -1),
gear_q7(0.7, r, b, c, k, -1),
gear_q7(0.6, r, b, c, k, -1),
gear_q7(0.5, r, b, c, k, -1),
gear_q7(0.4, r, b, c, k, -1),
gear_q7(0.3, r, b, c, k, -1),
gear_q7(0.2, r, b, c, k, -1),
gear_q7(0.1, r, b, c, k, -1),
gear_q7(0.0, r, b, c, k, -1),
gear_polar(r,
-k if r < b else pi / number_of_teeth)])
utils.shapelyToCurve('tooth', shapely_gear, 0.0)
i = number_of_teeth
while i > 1:
simple.duplicate()
simple.rotate(2 * math.pi / number_of_teeth)
i -= 1
simple.join_multiple('tooth')
simple.active_name('_teeth')
bpy.ops.curve.simple(align='WORLD',
location=(0, 0, 0),
rotation=(0, 0, 0),
Simple_Type='Circle',
Simple_radius=r,
shape='3D',
use_cyclic_u=True,
edit_mode=False)
simple.active_name('_hub')
simple.union('_')
simple.active_name('_gear')
simple.remove_doubles()
if spokes > 0:
bpy.ops.curve.simple(align='WORLD',
location=(0, 0, 0),
rotation=(0, 0, 0),
Simple_Type='Circle',
Simple_radius=r - rim_size,
shape='3D',
use_cyclic_u=True,
edit_mode=False)
simple.active_name('_hole')
simple.difference('_', '_gear')
bpy.ops.curve.simple(align='WORLD',
location=(0, 0, 0),
rotation=(0, 0, 0),
Simple_Type='Circle',
Simple_radius=hub_diameter / 2,
shape='3D',
use_cyclic_u=True,
edit_mode=False)
simple.active_name('_hub')
bpy.ops.curve.simple(align='WORLD',
location=(0, 0, 0),
rotation=(0, 0, 0),
Simple_Type='Circle',
Simple_radius=hole_diameter / 2,
shape='3D',
use_cyclic_u=True,
edit_mode=False)
simple.active_name('_hub_hole')
simple.difference('_hub', '_hub')
simple.join_multiple('_')
simple.add_rectangle(
r - rim_size -
((hub_diameter - hole_diameter) / 4 + hole_diameter / 2),
hub_diameter / 2,
center_x=False)
simple.move(x=(hub_diameter - hole_diameter) / 4 + hole_diameter / 2)
simple.active_name('_spoke')
angle = 2 * pi / spokes
while spokes > 0:
simple.duplicate()
simple.rotate(angle)
spokes -= 1
simple.union('_spoke')
simple.remove_doubles()
simple.union('_')
else:
bpy.ops.curve.simple(align='WORLD',
location=(0, 0, 0),
rotation=(0, 0, 0),
Simple_Type='Circle',
Simple_radius=hole_diameter,
shape='3D',
use_cyclic_u=True,
edit_mode=False)
simple.active_name('_hole')
simple.difference('_', '_gear')
name = 'gear-' + str(round(mm_per_tooth * 1000, 1))
name += 'mm-pitch-' + str(number_of_teeth)
name += 'teeth-PA-' + str(round(math.degrees(pressure_angle), 1))
simple.active_name(name)