def test_roadm_target_power(prev_node_type, effective_pch_out_db, power_dbm):
''' Check that egress power of roadm is equal to target power if input power is greater
than target power else, that it is equal to input power. Use a simple two hops A-B-C topology
for the test where the prev_node in ROADM B is either an amplifier or a fused, so that the target
power can not be met in this last case.
'''
equipment = load_equipment(EQPT_LIBRARY_NAME)
json_network = load_json(TEST_DIR / 'data/twohops_roadm_power_test.json')
prev_node = next(n for n in json_network['elements']
if n['uid'] == 'west edfa in node B to ila2')
json_network['elements'].remove(prev_node)
if prev_node_type == 'edfa':
prev_node = {'uid': 'west edfa in node B to ila2', 'type': 'Edfa'}
elif prev_node_type == 'fused':
prev_node = {'uid': 'west edfa in node B to ila2', 'type': 'Fused'}
prev_node['params'] = {'loss': 0}
json_network['elements'].append(prev_node)
network = network_from_json(json_network, equipment)
p_total_db = power_dbm + lin2db(
automatic_nch(equipment['SI']['default'].f_min,
equipment['SI']['default'].f_max,
equipment['SI']['default'].spacing))
build_network(network, equipment, power_dbm, p_total_db)
params = {
'request_id': 0,
'trx_type': '',
'trx_mode': '',
'source': 'trx node A',
'destination': 'trx node C',
'bidir': False,
'nodes_list': ['trx node C'],
'loose_list': ['strict'],
'format': '',
'path_bandwidth': 100e9,
'effective_freq_slot': None,
}
trx_params = trx_mode_params(equipment)
params.update(trx_params)
req = PathRequest(**params)
req.power = db2lin(power_dbm - 30)
path = compute_constrained_path(network, req)
si = create_input_spectral_information(req.f_min, req.f_max, req.roll_off,
req.baud_rate, req.power,
req.spacing)
for i, el in enumerate(path):
if isinstance(el, Roadm):
carriers_power_in_roadm = min([
c.power.signal + c.power.nli + c.power.ase for c in si.carriers
])
si = el(si, degree=path[i + 1].uid)
if el.uid == 'roadm node B':
print('input', carriers_power_in_roadm)
# if previous was an EDFA, power level at ROADM input is enough for the ROADM to apply its
# target power (as specified in equipment ie -20 dBm)
# if it is a Fused, the input power to the ROADM is smaller than the target power, and the
# ROADM cannot apply this target. In this case, it is assumed that the ROADM has 0 dB loss
# so the output power will be the same as the input power, which for this particular case
# corresponds to -22dBm + power_dbm
# next step (for ROADM modelling) will be to apply a minimum loss for ROADMs !
if prev_node_type == 'edfa':
assert el.effective_pch_out_db == effective_pch_out_db
if prev_node_type == 'fused':
# then output power == input_power == effective_pch_out_db + power_dbm
assert effective_pch_out_db + power_dbm == \
pytest.approx(lin2db(carriers_power_in_roadm * 1e3), rel=1e-3)
assert el.effective_pch_out_db == effective_pch_out_db + power_dbm
for carrier in si.carriers:
print(carrier.power.signal + carrier.power.nli +
carrier.power.ase)
power = carrier.power.signal + carrier.power.nli + carrier.power.ase
if prev_node_type == 'edfa':
# edfa prev_node sets input power to roadm to a high enough value:
# Check that egress power of roadm is equal to target power
assert power == pytest.approx(
db2lin(effective_pch_out_db - 30), rel=1e-3)
elif prev_node_type == 'fused':
# fused prev_node does reamplfy power after fiber propagation, so input power
# to roadm is low.
# Check that egress power of roadm is equalized to the min carrier input power.
assert power == pytest.approx(carriers_power_in_roadm,
rel=1e-3)
else:
si = el(si)
def transmission_main_example(args=None):
parser = argparse.ArgumentParser(
description=
'Send a full spectrum load through the network from point A to point B',
epilog=_help_footer,
formatter_class=argparse.ArgumentDefaultsHelpFormatter,
)
_add_common_options(parser,
network_default=_examples_dir /
'edfa_example_network.json')
parser.add_argument('--show-channels',
action='store_true',
help='Show final per-channel OSNR summary')
parser.add_argument('-pl', '--plot', action='store_true')
parser.add_argument('-l',
'--list-nodes',
action='store_true',
help='list all transceiver nodes')
parser.add_argument('-po',
'--power',
default=0,
help='channel ref power in dBm')
parser.add_argument('source', nargs='?', help='source node')
parser.add_argument('destination', nargs='?', help='destination node')
args = parser.parse_args(args if args is not None else sys.argv[1:])
_setup_logging(args)
(equipment,
network) = load_common_data(args.equipment, args.topology,
args.sim_params,
args.save_network_before_autodesign)
if args.plot:
plot_baseline(network)
transceivers = {
n.uid: n
for n in network.nodes() if isinstance(n, Transceiver)
}
if not transceivers:
sys.exit('Network has no transceivers!')
if len(transceivers) < 2:
sys.exit('Network has only one transceiver!')
if args.list_nodes:
for uid in transceivers:
print(uid)
sys.exit()
# First try to find exact match if source/destination provided
if args.source:
source = transceivers.pop(args.source, None)
valid_source = True if source else False
else:
source = None
_logger.info('No source node specified: picking random transceiver')
if args.destination:
destination = transceivers.pop(args.destination, None)
valid_destination = True if destination else False
else:
destination = None
_logger.info(
'No destination node specified: picking random transceiver')
# If no exact match try to find partial match
if args.source and not source:
# TODO code a more advanced regex to find nodes match
source = next(
(transceivers.pop(uid)
for uid in transceivers if args.source.lower() in uid.lower()),
None)
if args.destination and not destination:
# TODO code a more advanced regex to find nodes match
destination = next((transceivers.pop(uid) for uid in transceivers
if args.destination.lower() in uid.lower()), None)
# If no partial match or no source/destination provided pick random
if not source:
source = list(transceivers.values())[0]
del transceivers[source.uid]
if not destination:
destination = list(transceivers.values())[0]
_logger.info(f'source = {args.source!r}')
_logger.info(f'destination = {args.destination!r}')
params = {}
params['request_id'] = 0
params['trx_type'] = ''
params['trx_mode'] = ''
params['source'] = source.uid
params['destination'] = destination.uid
params['bidir'] = False
params['nodes_list'] = [destination.uid]
params['loose_list'] = ['strict']
params['format'] = ''
params['path_bandwidth'] = 0
trx_params = trx_mode_params(equipment)
# Randomly generate input power
input_power = round(random.random(), 2)
input_power = -2 + (input_power * (8))
args.power = input_power
if args.power:
trx_params['power'] = db2lin(float(args.power)) * 1e-3
params.update(trx_params)
req = PathRequest(**params)
power_mode = equipment['Span']['default'].power_mode
print('\n'.join([
f'Power mode is set to {power_mode}',
f'=> it can be modified in eqpt_config.json - Span'
]))
pref_ch_db = lin2db(req.power *
1e3) # reference channel power / span (SL=20dB)
pref_total_db = pref_ch_db + lin2db(
req.nb_channel) # reference total power / span (SL=20dB)
try:
build_network(network, equipment, pref_ch_db, pref_total_db)
except exceptions.NetworkTopologyError as e:
print(
f'{ansi_escapes.red}Invalid network definition:{ansi_escapes.reset} {e}'
)
sys.exit(1)
except exceptions.ConfigurationError as e:
print(
f'{ansi_escapes.red}Configuration error:{ansi_escapes.reset} {e}')
sys.exit(1)
path = compute_constrained_path(network, req)
spans = [
s.params.length for s in path
if isinstance(s, RamanFiber) or isinstance(s, Fiber)
]
print(
f'\nThere are {len(spans)} fiber spans over {sum(spans)/1000:.0f} km between {source.uid} '
f'and {destination.uid}')
print(f'\nNow propagating between {source.uid} and {destination.uid}:')
try:
p_start, p_stop, p_step = equipment['SI']['default'].power_range_db
p_num = abs(int(round(
(p_stop - p_start) / p_step))) + 1 if p_step != 0 else 1
power_range = list(linspace(p_start, p_stop, p_num))
except TypeError:
print(
'invalid power range definition in eqpt_config, should be power_range_db: [lower, upper, step]'
)
power_range = [0]
if not power_mode:
# power cannot be changed in gain mode
power_range = [0]
for dp_db in power_range:
req.power = db2lin(pref_ch_db + dp_db) * 1e-3
if power_mode:
print(
f'\nPropagating with input power = {ansi_escapes.cyan}{lin2db(req.power*1e3):.2f} dBm{ansi_escapes.reset}:'
)
else:
print(
f'\nPropagating in {ansi_escapes.cyan}gain mode{ansi_escapes.reset}: power cannot be set manually'
)
infos = propagate(path, req, equipment)
if len(power_range) == 1:
for elem in path:
print(elem)
if power_mode:
print(
f'\nTransmission result for input power = {lin2db(req.power*1e3):.2f} dBm:'
)
else:
print(f'\nTransmission results:')
# print('-------------')
# print(destination.snr_01nm)
# print('-------------')
print(
f' Final SNR total (0.1 nm): {ansi_escapes.cyan}{mean(destination.snr_01nm):.02f} dB{ansi_escapes.reset}'
)
else:
print(path[-1])
if args.save_network is not None:
save_network(network, args.save_network)
print(
f'{ansi_escapes.blue}Network (after autodesign) saved to {args.save_network}{ansi_escapes.reset}'
)
if args.show_channels:
print('\nThe total SNR per channel at the end of the line is:')
print('{:>5}{:>26}{:>26}{:>28}{:>28}{:>28}'.format(
'Ch. #', 'Channel frequency (THz)', 'Channel power (dBm)',
'OSNR ASE (signal bw, dB)', 'SNR NLI (signal bw, dB)',
'SNR total (signal bw, dB)'))
# print(dir(info))
for final_carrier, ch_osnr, ch_snr_nl, ch_snr in zip(
infos.carriers, path[-1].osnr_ase, path[-1].osnr_nli,
path[-1].snr):
ch_freq = final_carrier.frequency * 1e-12
ch_power = lin2db(final_carrier.power.signal * 1e3)
print('{:5}{:26.2f}{:26.2f}{:28.2f}{:28.2f}{:28.2f}'.format(
final_carrier.channel_number, round(ch_freq, 2),
round(ch_power, 2), round(ch_osnr, 2), round(ch_snr_nl, 2),
round(ch_snr, 2)))
if not args.source:
print(f'\n(No source node specified: picked {source.uid})')
elif not valid_source:
print(
f'\n(Invalid source node {args.source!r} replaced with {source.uid})'
)
if not args.destination:
print(f'\n(No destination node specified: picked {destination.uid})')
elif not valid_destination:
print(
f'\n(Invalid destination node {args.destination!r} replaced with {destination.uid})'
)
if args.plot:
plot_results(network, path, source, destination)
# MY ADDITION
# just to see what the different contributions of ASE and NLI are
# return input_power, path[-1].osnr_ase, path[-1].osnr_nli, path[-1].snr
# to test Raman
return input_power, destination.snr_01nm, mean(destination.snr_01nm)
def test_roadm_target_power(prev_node_type, effective_pch_out_db):
''' Check that egress power of roadm is equal to target power if input power is greater
than target power else, that it is equal to input power. Use a simple two hops A-B-C topology
for the test where the prev_node in ROADM B is either an amplifier or a fused, so that the target
power can not be met in this last case.
'''
equipment = load_equipment(EQPT_LIBRARY_NAME)
json_network = load_json(TEST_DIR / 'data/twohops_roadm_power_test.json')
prev_node = next(n for n in json_network['elements']
if n['uid'] == 'west edfa in node B to ila2')
json_network['elements'].remove(prev_node)
if prev_node_type == 'edfa':
prev_node = {'uid': 'west edfa in node B to ila2', 'type': 'Edfa'}
elif prev_node_type == 'fused':
prev_node = {'uid': 'west edfa in node B to ila2', 'type': 'Fused'}
prev_node['params'] = {'loss': 0}
json_network['elements'].append(prev_node)
network = network_from_json(json_network, equipment)
# Build the network once using the default power defined in SI in eqpt config
p_db = equipment['SI']['default'].power_dbm
p_total_db = p_db + lin2db(
automatic_nch(equipment['SI']['default'].f_min,
equipment['SI']['default'].f_max,
equipment['SI']['default'].spacing))
build_network(network, equipment, p_db, p_total_db)
params = {}
params['request_id'] = 0
params['trx_type'] = ''
params['trx_mode'] = ''
params['source'] = 'trx node A'
params['destination'] = 'trx node C'
params['bidir'] = False
params['nodes_list'] = ['trx node C']
params['loose_list'] = ['strict']
params['format'] = ''
params['path_bandwidth'] = 100e9
trx_params = trx_mode_params(equipment)
params.update(trx_params)
req = PathRequest(**params)
path = compute_constrained_path(network, req)
si = create_input_spectral_information(req.f_min, req.f_max, req.roll_off,
req.baud_rate, req.power,
req.spacing)
for i, el in enumerate(path):
if isinstance(el, Roadm):
carriers_power_in_roadm = min([
c.power.signal + c.power.nli + c.power.ase for c in si.carriers
])
si = el(si, degree=path[i + 1].uid)
if el.uid == 'roadm node B':
print('input', carriers_power_in_roadm)
assert el.effective_pch_out_db == effective_pch_out_db
for carrier in si.carriers:
print(carrier.power.signal + carrier.power.nli +
carrier.power.ase)
power = carrier.power.signal + carrier.power.nli + carrier.power.ase
if prev_node_type == 'edfa':
# edfa prev_node sets input power to roadm to a high enough value:
# Check that egress power of roadm is equal to target power
assert power == pytest.approx(
db2lin(effective_pch_out_db - 30), rel=1e-3)
elif prev_node_type == 'fused':
# fused prev_node does reamplfy power after fiber propagation, so input power
# to roadm is low.
# Check that egress power of roadm is equalized to the min carrier input power.
assert power == pytest.approx(carriers_power_in_roadm,
rel=1e-3)
else:
si = el(si)