def run_receiver():
""" Setup the Raspberry Pi as receiver, listen for transmitted values,
display every received number as binary < 256 if the display is attached.
Prints the received value, bit length and protocol to the terminal. """
receiver = RCSwitchReceiver()
receiver.enableReceive(2)
while True:
print 'Listening...'
sleep(0.5)
if receiver.available():
received_value = receiver.getReceivedValue()
if received_value:
display_number(received_value % 256, True)
print("Value: %s | Bit: %s | Protocol: %s" %
(received_value, receiver.getReceivedBitlength(),
receiver.getReceivedProtocol()))
receiver.resetAvailable()
from pi_switch import RCSwitchReceiver
from Config import Config
#---------------------------------------------------------------------------#
# Configure receiver
#---------------------------------------------------------------------------#
receiver = RCSwitchReceiver()
receiver.enableReceive(Config.RPi_Pin_Receiver)
num = 0
#---------------------------------------------------------------------------#
# Loop and wait for commands
#---------------------------------------------------------------------------#
while True:
if receiver.available():
received_value = receiver.getReceivedValue()
if received_value:
num += 1
print("Received[%s]:" % num)
print(received_value)
print("%s / %s bit" %
(received_value, receiver.getReceivedBitlength()))
print("Protocol: %s" % receiver.getReceivedProtocol())
print("")
receiver.resetAvailable()
#mqttClient.connect("54.187.15.61",1883)
mqttClient.connect("54.67.96.20",1883)
message={}
while True:
if receiver.available():
received_value = receiver.getReceivedValue()
if received_value:
num += 1
print("Received[%s]:" % num)
print(received_value)
print("%s / %s bit" % (received_value, receiver.getReceivedBitlength()))
print("Protocol: %s" % receiver.getReceivedProtocol())
print("")
lst = [int(i) for i in str(received_value)]
print(lst[1])
try:
checkSum=lst[0]+lst[1]+lst[2]+lst[3]+lst[4]
checkSum=checkSum*lst[4]
except:
print("exception: less than 7 digits")
print("checksum")
print(checkSum)
vb=lst[5:]
print(vb)
vb1=''.join(map(str,vb))
print(vb1)
if checkSum!=int(vb1):
lista_valores[10].sensor_desc = 'temp10'
lista_valores[11].sensor_desc = ' hum11'
lista_valores[12].sensor_desc = ' bat12'
lista_valores[13].sensor_desc = 'temp13'
lista_valores[14].sensor_desc = ' hum14'
lista_valores[15].sensor_desc = 'pres15'
lista_valores[16].sensor_desc = 'P_Te16'
lista_valores[17].sensor_desc = 'void'
lista_valores[18].sensor_desc = 'void'
print lista_valores[1].sensor_desc
# inicializamos RCSwitch
receiver = RCSwitchReceiver()
receiver.enableReceive(0)
procesa_valor(14003540)
imprime_lista()
while True:
print dt.now()
# procesa_valor(14003540)
if receiver.available():
received_value = receiver.getReceivedValue()
if received_value:
print("Value: %s | Bit: %s | Protocol: %s" % (received_value,
receiver.getReceivedBitlength(),
receiver.getReceivedProtocol()))
procesa_valor(received_value)
receiver.resetAvailable()
sleep(10)
#!/usr/bin/python
# coding=utf-8
from pi_switch import RCSwitchReceiver
receiver = RCSwitchReceiver()
receiver.enableReceive(2)
num = 0
while True:
if receiver.available():
received_value = receiver.getReceivedValue()
if received_value:
num += 1
print("Received[{}]: {}".format(num, received_value))
print("Bit Length: {} bit".format(receiver.getReceivedBitlength()))
print("Delay: {}".format(receiver.getReceivedDelay()))
print("Protocol: {}\n".format(receiver.getReceivedProtocol()))
receiver.resetAvailable()
