def BuildModel():
model1 = model(settings)
H = 4.875 # total height
B = 10 # total width
t1 = 0.4375 # thickness of the ploymer concrete
t3 = 0.125 # offset of the top plate
t2 = H - t1 -t3 # height of the second portion
b3 = 1.375 # top-left portion
b4 = B - b3 * 2 # top-middle portion
b1 = 3.75
b2 = B - b1 * 2
alpha = atan(t2/(b1-b3))
#alpha = 60.0/180.0* 3.1415926 # incline angle
#b1 = b3 + t2 / float(alpha)
#b2 = B - b1 * 2
# Define nodes
N1 = [0.0,H,0]
N2 = [0,t2,0]
N3 = [0,0,0]
N4 = [b3,t2,0]
N5 = [b1,0,0]
N6 = [b3+b4,t2,0]
N7 = [b1+b2,0,0]
N8 = [B,H,0]
N9 = [B,t2,0]
N10 = [B,0,0]
N11 = [b3,H,0]
N12 = [b3+b4,H,0]
N13 = [0,t2 + t3,0]
N14 = [b3,t2 + t3,0]
N15 = [b3 + b4,t2 + t3,0]
N16 = [B,t2 + t3,0]
tempnodes = [N1,N2,N3,N4,N5,N6,N7,N8,N9,N10,N11,N12,N13,N14,N15,N16]
# create t1
model1.node(tempnodes)
Lsize_seg_B = 0.5
Lsize_seg_H = 0.25
model1 = create_2d_patch(model1,[2,3,5,4],[floor(int(t2/Lsize_seg_H)),floor(int(b3/Lsize_seg_B))*2],setname='bottom_left')
model1 = create_2d_patch(model1,[4,5,7,6],[floor(int(t2/Lsize_seg_H)),floor(int(b4/Lsize_seg_B))],setname='bottom_middle')
model1 = create_2d_patch(model1,[6,7,10,9],[floor(int(t2/Lsize_seg_H)),floor(int(b3/Lsize_seg_B))*2],setname='bottom_right')
model1 = create_2d_patch(model1,[1,13,14,11],[floor(int(t1/Lsize_seg_H))+1,floor(int(b3/Lsize_seg_B))*2],setname='top_left')
model1 = create_2d_patch(model1,[11,14,15,12],[floor(int(t1/Lsize_seg_H))+1,floor(int(b4/Lsize_seg_B))],setname='top_middle')
model1 = create_2d_patch(model1,[12,15,16,8],[floor(int(t1/Lsize_seg_H))+1,floor(int(b3/Lsize_seg_B))*2],setname='top_right')
# create line elements that will be stretched to the frp plate
model1 = create_single_line_setname(model1,'bottom_left-1-4',mode='x',ressetname='L1')
model1 = create_single_line_setname(model1,'bottom_middle-1-4',mode='x',ressetname='L1')
model1 = create_single_line_setname(model1,'bottom_right-1-4',mode='x',ressetname='L1')
model1 = create_single_line_setname(model1,'bottom_left-1-4',mode='x',ressetname='L2')
model1 = create_single_line_setname(model1,'bottom_right-1-4',mode='x',ressetname='L2')
model1 = create_single_line_setname(model1,'bottom_middle-1-2',mode='x',ressetname='L3')
model1 = create_single_line_setname(model1,'bottom_middle-3-4',mode='x',ressetname='L3')
model1 = create_single_line_setname(model1,'bottom_middle-2-3',mode='x',ressetname='L4')
model1 = create_single_line_setname(model1,'bottom_left-2-3',mode='x',ressetname='L5')
model1 = create_single_line_setname(model1,'bottom_middle-2-3',mode='x',ressetname='L5')
model1 = create_single_line_setname(model1,'bottom_right-2-3',mode='x',ressetname='L5')
# stretch the mesh to generate 3D
L_total = 50.0
Lincr = 2.0
n_incr = int(L_total/Lincr)
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['L1'],setname='plate_frp_L1')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['L2'],setname='plate_frp_L2')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['L3'],setname='plate_frp_L3')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['L4'],setname='plate_frp_L4')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['L5'],setname='plate_frp_L5')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['bottom_left'],setname='solid_bottom_left')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['bottom_middle'],setname='solid_bottom_middle')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['bottom_right'],setname='solid_bottom_right')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['top_left'],setname='solid_top_left')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['top_middle'],setname='solid_top_middle')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['top_right'],setname='solid_top_right')
# merge duplicate nodes
model1.sweep()
# create interface
#for i in range(0,floor(int(B/Lsize_seg_B)))
interfacenodelist = model1.nodelist.select_node_coord(rz=[-0.001,0.001],ry=[t2-0.01,t2+0.01])
#model1 = create_interface(model1,[-b1/2.0,h-tf,0],[-b1/2.0,h-tf1,0],2,24,setname='interface_left')
for nodeid in interfacenodelist:
xyz = model1.nodelist.itemlib[nodeid].xyz
xyz = list(xyz)
model1 = create_interface(model1,xyz,[xyz[0],xyz[1]+t3,xyz[2]],Lincr,n_incr,setname='interface')
exp1 = exporter(model1,'hybrid.proc','ex_Marc_dat')
exp1.export('default')
#t0 = time.time()
model1.modelsavetofile('hybrid.pydat')
def BuildModel_hybrid_command(*args):
model1 = model(settings)
H = float(args[0])
B = float(args[1])
t1 = float(args[2])
t3 = float(args[3]) # mess with t2 as t3
b3 = float(args[4])
a = float(args[5])
L = float(args[6])
Mesh_H = float(args[7])
Mesh_B = float(args[8])
Mesh_L = float(args[9])
#H = 4.875 # total height
#B = 10 # total width
#t1 = 0.5 # thickness of the ploymer concrete
#t3 = 0.125 # offset of the top plate
t2 = H - t1 -t3 # height of the second portion
#b3 = 1.375 # top-left portion
b4 = B - b3 * 2 # top-middle portion
b1 = b3 + t2/tan(a/180.0*3.1415926)
b2 = B - b1 * 2
#alpha = atan(t2/(b1-b3)) # incline angle
# Define nodes
N1 = [0.0,H,0]
N2 = [0,t2,0]
N3 = [0,0,0]
N4 = [b3,t2,0]
N5 = [b1,0,0]
N6 = [b3+b4,t2,0]
N7 = [b1+b2,0,0]
N8 = [B,H,0]
N9 = [B,t2,0]
N10 = [B,0,0]
N11 = [b3,H,0]
N12 = [b3+b4,H,0]
N13 = [0,t2 + t3,0]
N14 = [b3,t2 + t3,0]
N15 = [b3 + b4,t2 + t3,0]
N16 = [B,t2 + t3,0]
tempnodes = [N1,N2,N3,N4,N5,N6,N7,N8,N9,N10,N11,N12,N13,N14,N15,N16]
# create t1
model1.node(tempnodes)
Lsize_seg_B = Mesh_B
Lsize_seg_H = Mesh_H
model1 = create_2d_patch(model1,[2,3,5,4],[floor(int(t2/Lsize_seg_H)),floor(int(b3/Lsize_seg_B))*2],setname='bottom_left')
model1 = create_2d_patch(model1,[4,5,7,6],[floor(int(t2/Lsize_seg_H)),floor(int(b4/Lsize_seg_B))],setname='bottom_middle')
model1 = create_2d_patch(model1,[6,7,10,9],[floor(int(t2/Lsize_seg_H)),floor(int(b3/Lsize_seg_B))*2],setname='bottom_right')
model1 = create_2d_patch(model1,[1,13,14,11],[floor(int(t1/Lsize_seg_H))+1,floor(int(b3/Lsize_seg_B))*2],setname='top_left')
model1 = create_2d_patch(model1,[11,14,15,12],[floor(int(t1/Lsize_seg_H))+1,floor(int(b4/Lsize_seg_B))],setname='top_middle')
model1 = create_2d_patch(model1,[12,15,16,8],[floor(int(t1/Lsize_seg_H))+1,floor(int(b3/Lsize_seg_B))*2],setname='top_right')
# create line elements that will be stretched to the frp plate
model1 = create_single_line_setname(model1,'bottom_left-1-4',mode='x',ressetname='L1')
model1 = create_single_line_setname(model1,'bottom_middle-1-4',mode='x',ressetname='L1')
model1 = create_single_line_setname(model1,'bottom_right-1-4',mode='x',ressetname='L1')
model1 = create_single_line_setname(model1,'bottom_left-1-4',mode='x',ressetname='L2')
model1 = create_single_line_setname(model1,'bottom_right-1-4',mode='x',ressetname='L2')
model1 = create_single_line_setname(model1,'bottom_middle-1-2',mode='x',ressetname='L3')
model1 = create_single_line_setname(model1,'bottom_middle-3-4',mode='x',ressetname='L3')
model1 = create_single_line_setname(model1,'bottom_middle-2-3',mode='x',ressetname='L4')
model1 = create_single_line_setname(model1,'bottom_left-2-3',mode='x',ressetname='L5')
model1 = create_single_line_setname(model1,'bottom_middle-2-3',mode='x',ressetname='L5')
model1 = create_single_line_setname(model1,'bottom_right-2-3',mode='x',ressetname='L5')
# stretch the mesh to generate 3D
L_total = L
Lincr = Mesh_L
n_incr = int(L_total/Lincr)
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['L1'],setname='plate_frp_L1')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['L2'],setname='plate_frp_L2')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['L3'],setname='plate_frp_L3')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['L4'],setname='plate_frp_L4')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['L5'],setname='plate_frp_L5')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['bottom_left'],setname='solid_bottom_left')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['bottom_middle'],setname='solid_bottom_middle')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['bottom_right'],setname='solid_bottom_right')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['top_left'],setname='solid_top_left')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['top_middle'],setname='solid_top_middle')
model1,a,b,c = sktretch_2dmesh(model1,n_incr,Lincr,ElemSetNameList=['top_right'],setname='solid_top_right')
# merge duplicate nodes
model1.sweep()
# create interface
#for i in range(0,floor(int(B/Lsize_seg_B)))
interfacenodelist = model1.nodelist.select_node_coord(rz=[-0.001,0.001],ry=[t2-0.01,t2+0.01])
#model1 = create_interface(model1,[-b1/2.0,h-tf,0],[-b1/2.0,h-tf1,0],2,24,setname='interface_left')
for nodeid in interfacenodelist:
xyz = model1.nodelist.itemlib[nodeid].xyz
xyz = list(xyz)
model1 = create_interface(model1,xyz,[xyz[0],xyz[1]+t3,xyz[2]],Lincr,n_incr,setname='interface')
return model1
def rec_planeconfig(model1,name,b,h,d,bh,hh,LL,dL,dow_sep_incr):
""" Create nodes and elements on surface
b: width
h: height
d: location of rebar measure from top
bh: width of the hole
hh: height of the hole
LL: Total length
dL: increment of length
"""
# create surface meshing
nsegL = int(LL/dL)
nod1 = (-b/2.0,h,0)
nod2 = (-b/2.0,h-d+hh/2.0,0)
nod3 = (-b/2.0,h-d-hh/2.0,0)
nod4 = (-b/2.0,0,0)
nod5 = (-bh/2.0,h,0)
nod6 = (-bh/2.0,h-d+hh/2.0,0)
nod7 = (-bh/2.0,h-d-hh/2.0,0)
nod8 = (-bh/2.0,0,0)
nod9 = (0,h,0)
nod10 = (0,h-d+hh/2.0,0)
nod11 = (0,h-d-hh/2.0,0)
nod12 = (0,0,0)
# create plane 2d connectivity based on stretch
model1 = create_2D_patch_xy(model1,nod1,nod2,nod6,nod5,0.25,0.25)
model1 = create_2D_patch_xy(model1,nod2,nod3,nod7,nod6,0.25,0.25)
model1 = create_2D_patch_xy(model1,nod3,nod4,nod8,nod7,0.25,0.25)
model1 = create_2D_patch_xy(model1,nod5,nod6,nod10,nod9,0.25,0.25)
model1 = create_2D_patch_xy(model1,nod7,nod8,nod12,nod11,0.25,0.25)
# strecth 2d to 3d
model1,nodekeylist,new_id,n_nodelist = sktretch_2dmesh(model1,nsegL,dL,setname='sec')
# add reinforcement
model1 = create_single_line_nodecoord(model1,[0,h-d,0],[0,h-d,LL],nsegL,elemsetname='rebar')
# create interface elements
topnodeid = model1.pick_node_coord_3d([0,h-d+hh/2.0,0])
botnodeid = model1.pick_node_coord_3d([0,h-d-hh/2.0,0])
centernodeid = model1.pick_node_coord_3d([0,h-d,0])
tempquadnodelist_top = []
tempquadnodelist_bot = []
for i in range(0,nsegL):
if i == 0:
tempquadnodelist_top.append([centernodeid,centernodeid+2,new_id+1+nodekeylist.index(topnodeid),topnodeid])
tempquadnodelist_bot.append([botnodeid,new_id+1+nodekeylist.index(botnodeid),centernodeid+2,centernodeid])
elif i == nsegL-1:
tempquadnodelist_top.append([centernodeid+i+1,centernodeid+1,
new_id+1+nodekeylist.index(topnodeid)+n_nodelist*(i),
new_id+1+nodekeylist.index(topnodeid)+n_nodelist*(i-1)])
tempquadnodelist_bot.append([new_id+1+nodekeylist.index(botnodeid)+n_nodelist*(i-1),
new_id+1+nodekeylist.index(botnodeid)+n_nodelist*(i),
centernodeid+1,centernodeid+i+1])
else:
tempquadnodelist_top.append([centernodeid+i+1,centernodeid+i+2,
new_id+1+nodekeylist.index(topnodeid)+n_nodelist*(i),
new_id+1+nodekeylist.index(topnodeid)+n_nodelist*(i-1)])
tempquadnodelist_bot.append([new_id+1+nodekeylist.index(botnodeid)+n_nodelist*(i-1),
new_id+1+nodekeylist.index(botnodeid)+n_nodelist*(i),
centernodeid+i+2,centernodeid+i+1])
model1.element(tempquadnodelist_top,setname='interface_top')
model1.element(tempquadnodelist_bot,setname='interface_bot')
'''
# add property to the elements
model1.property('uhpc','hex8',paralib={'element_id':117,'setnamelist':['element_sec']})
model1.property('rebar','line2',paralib={'element_id':98,'setnamelist':['rebar']})
model1.property('interface','interface_linear',paralib={'element_id':186,'setnamelist':['interface']})
model1.link_prop_conn('uhpc')
model1.link_prop_conn('rebar')
model1.link_prop_conn('interface')
'''
return model1
def BuildModel():
model1 = model(settings)
bf = 12.0 # width of flange UHPportion
tf = 1.0 # thickness of flange UHPportion
h = 5.0 # total section height
tf1 = 1.25 # distance between UHPC and frp top plate
t1 = 0.25 # thickness of top portion FRP
b1 = 6 # width of top portion FRP
t2 = 0.25 # thickness of inclined FRP portion
ang2 = 60 # angle of inclined FRP portion
t3 = 0.25 # Thickness of the botton center part
t4 = 0.25 # Thickness of the botton side part
L = 48.0
Lsize = 2.0
bsize = 1.0
hsize = 0.25
d = h - max(t3, t4) / 2.0 # effective depth from center
# get width of center part
h2 = d - tf1
b3 = b1 + h2 * 2 / tan(float(ang2) / 180.0 * 3.1415926)
b4h = (bf - b3) / 2.0
# Define nodes
N1 = [-bf / 2.0, 0, 0]
N2 = [-b3 / 2.0, 0, 0]
N3 = [0, 0, 0]
N4 = [b3 / 2.0, 0, 0]
N5 = [bf / 2.0, 0, 0]
N6 = [-b1 / 2.0, h - tf1, 0]
N7 = [b1 / 2.0, h - tf1, 0]
N8 = [-b1 / 2.0, 0, 0]
N9 = [b1 / 2.0, 0, 0]
#t0 = time.time()
# create t1
mdoel1 = create_single_line_nodecoord(model1,
N6,
N7,
divident(N6, N7, bsize, 'Even'),
elemsetname='frp_t1')
mdoel1 = create_single_line_nodecoord(model1,
N1,
N2,
divident(N1, N2, bsize),
elemsetname='frp_t4_l')
mdoel1 = create_single_line_nodecoord(model1,
N2,
N8,
divident(N2, N6, bsize),
elemsetname='frp_t3_l')
mdoel1 = create_single_line_nodecoord(model1,
N8,
N9,
divident(N8, N9, bsize, 'Even'),
elemsetname='frp_t3')
mdoel1 = create_single_line_nodecoord(model1,
N9,
N4,
divident(N7, N4, bsize),
elemsetname='frp_t3_r')
mdoel1 = create_single_line_nodecoord(model1,
N4,
N5,
divident(N4, N5, bsize),
elemsetname='frp_t4_r')
mdoel1 = create_single_line_nodecoord(model1,
N2,
N6,
divident(N2, N6, bsize),
elemsetname='frp_t2_l')
mdoel1 = create_single_line_nodecoord(model1,
N7,
N4,
divident(N7, N4, bsize),
elemsetname='frp_t2_r')
#t1 = time.time() - t0
#print 'time to construct FRP layers %s ' % str(t1)
#t0 = time.time()
model1, a, b, c = sktretch_2dmesh(model1,
24,
2,
ElemSetNameList=['frp_t1'],
setname='plate_frp_t1')
model1, a, b, c = sktretch_2dmesh(model1,
24,
2,
ElemSetNameList=['frp_t2_l', 'frp_t2_r'],
setname='plate_frp_t2')
model1, a, b, c = sktretch_2dmesh(
model1,
24,
2,
ElemSetNameList=['frp_t3_l', 'frp_t3_r', 'frp_t3'],
setname='plate_frp_t3')
model1, a, b, c = sktretch_2dmesh(model1,
24,
2,
ElemSetNameList=['frp_t4_l', 'frp_t4_r'],
setname='plate_frp_t4')
#t1 = time.time() - t0
#print 'time to Extrude FRP layers %s ' % str(t1)
# create top UHPC layer
#t0 = time.time()
model1 = create_3d_patch(model1, (0 - bf / 2.0, h - tf, 0),
(bsize, hsize, Lsize),
(bf / bsize, tf / hsize, L / Lsize),
setname='UHPC')
#t1 = time.time() - t0
#print 'time to construct UHPC %s ' % str(t1)
#t0 = time.time()
model1.sweep()
#t1 = time.time() - t0
#print 'time to sweep nodes %s ' % str(t1)
#t0 = time.time()
model1.nodelist.get_sortedcoordtable()
model1 = create_interface(model1, [-b1 / 2.0, h - tf, 0],
[-b1 / 2.0, h - tf1, 0],
2,
24,
setname='interface_left')
model1 = create_interface(model1, [0, h - tf, 0], [0, h - tf1, 0],
2,
24,
setname='interface_center')
model1 = create_interface(model1, [b1 / 2.0, h - tf, 0],
[b1 / 2.0, h - tf1, 0],
2,
24,
setname='interface_right')
#t1 = time.time() - t0
#print 'time to construct interface %s ' % str(t1)
# add and assign property
model1 = add_property(model1)
model1.section('frp_t1', 'shell_section', {'thickness': t1})
model1.section('frp_t2', 'shell_section', {'thickness': t2})
model1.section('frp_t3', 'shell_section', {'thickness': t3})
model1.section('frp_t4', 'shell_section', {'thickness': t4})
model1.section('interface', 'interface2d', {})
model1.link_sec_prop('frp_t1', 'frp_t1')
model1.link_sec_prop('frp_t2', 'frp_t2')
model1.link_sec_prop('frp_t3', 'frp_t3')
model1.link_sec_prop('frp_t4', 'frp_t4')
model1.link_sec_prop('interface', 'interface')
model1.link_prop_conn(
'interface',
setnamelist=['interface_left', 'interface_center', 'interface_right'])
model1.link_prop_conn('concrete', setnamelist=['UHPC'])
model1.link_prop_conn('frp_t1', setnamelist=['element_plate_frp_t1'])
model1.link_prop_conn('frp_t2', setnamelist=['element_plate_frp_t2'])
model1.link_prop_conn('frp_t3', setnamelist=['element_plate_frp_t3'])
model1.link_prop_conn('frp_t4', setnamelist=['element_plate_frp_t4'])
# create boundary conditions
leftbond = model1.nodelist.select_node_coord(rz=[0, 0], ry=[0, 0])
rightbond = model1.nodelist.select_node_coord(rz=[L, L], ry=[0, 0])
centerload = model1.nodelist.select_node_coord(rz=[L / 2.0, L / 2.0],
ry=[h, h])
centerlineload = model1.nodelist.select_node_coord(rx=[0, 0],
rz=[0, L],
ry=[h - tf, h - tf])
middlenode = model1.nodelist.select_node_coord(rx=[0, 0],
rz=[L / 2.0, L / 2.0],
ry=[0, 0])
model1.nodeset('middlenode', {'nodelist': middlenode})
model1.nodeset('leftbond', {'nodelist': leftbond})
model1.nodeset('rightbond', {'nodelist': rightbond})
model1.nodeset('centerload', {'nodelist': centerload})
model1.nodeset('centerlineload', {'nodelist': centerlineload})
model1.table('loadtable', 1, ['time'], [[0, 0], [1, 1]])
model1.bond('leftbond', {
'xyz': [1, 1, 1, 0, 0, 0],
'DOF': 6,
'setnamelist': ['leftbond']
})
model1.bond('rightbond', {
'xyz': [0, 1, 1, 0, 0, 0],
'DOF': 6,
'setnamelist': ['rightbond']
})
model1.bond('support_z', {
'xyz': [0, 0, 1, 0, 0, 0],
'DOF': 6,
'setnamelist': ['centerlineload']
})
model1.load(
'centerload', {
'xyz': [0, 1, 0, 0, 0, 0],
'DOF': 6,
'scalar': -4,
'setnamelist': ['centerload'],
'tabletag': 'loadtable'
})
# create Reb2
loadlinenode = model1.nodelist.select_node_coord(rz=[L / 2.0, L / 2.0],
ry=[h, h])
loadlinecenter = model1.nodelist.select_node_coord(rz=[L / 2.0, L / 2.0],
ry=[h, h],
rx=[0, 0])
# remove center node fron list
loadlinenode = loadlinenode.difference(loadlinecenter)
loadlinenode = list(loadlinenode)
loadlinecenter = list(loadlinecenter)
model1.nodaltie(
'rbe_load', 'marc_rbe2', {
'tietype': 'DY',
'tieid': 1,
'retnode': loadlinecenter[0],
'tienodelist': loadlinenode
})
model1.loadcase(
'loadcase1', 'static_arclength', {
'boundarylist':
['leftbond', 'centerload', 'rightbond', 'support_z'],
'para': {
'nstep': 50
}
})
model1.job(
'job1', 'static_job', {
'loadcaselist': ['loadcase1'],
'submit':
True,
'reqresultslist':
['stress', 'total_strain', 'crack_strain', 'plastic_strain']
})
# rotate
model1.nodelist.transform(ry=3.1415926 / 2.0)
exp1 = exporter(model1, 'hybrid.proc', 'ex_Marc_dat')
exp1.export('default')
#t0 = time.time()
model1.modelsavetofile('hybrid.pydat')
def BuildModel():
model1 = model(settings)
bf = 12.0 # width of flange UHPportion
tf = 1.0 # thickness of flange UHPportion
h = 5.0 # total section height
tf1 = 1.25 # distance between UHPC and frp top plate
t1 = 0.25 # thickness of top portion FRP
b1 = 6 # width of top portion FRP
t2 = 0.25 # thickness of inclined FRP portion
ang2 = 60 # angle of inclined FRP portion
t3 = 0.25 # Thickness of the botton center part
t4 = 0.25 # Thickness of the botton side part
L = 48.0
Lsize = 2.0
bsize = 1.0
hsize = 0.25
d = h - max(t3,t4)/2.0 # effective depth from center
# get width of center part
h2 = d - tf1
b3 = b1 + h2 *2 / tan(float(ang2)/180.0*3.1415926)
b4h = (bf - b3) / 2.0
# Define nodes
N1 = [-bf/2.0,0,0]
N2 = [-b3/2.0,0,0]
N3 = [0,0,0]
N4 = [b3/2.0,0,0]
N5 = [bf/2.0,0,0]
N6 = [-b1/2.0,h-tf1,0]
N7 = [b1/2.0,h-tf1,0]
N8 = [-b1/2.0,0,0]
N9 = [b1/2.0,0,0]
#t0 = time.time()
# create t1
mdoel1 = create_single_line_nodecoord(model1,N6,N7,divident(N6,N7,bsize,'Even'),elemsetname='frp_t1')
mdoel1 = create_single_line_nodecoord(model1,N1,N2,divident(N1,N2,bsize),elemsetname='frp_t4_l')
mdoel1 = create_single_line_nodecoord(model1,N2,N8,divident(N2,N6,bsize),elemsetname='frp_t3_l')
mdoel1 = create_single_line_nodecoord(model1,N8,N9,divident(N8,N9,bsize,'Even'),elemsetname='frp_t3')
mdoel1 = create_single_line_nodecoord(model1,N9,N4,divident(N7,N4,bsize),elemsetname='frp_t3_r')
mdoel1 = create_single_line_nodecoord(model1,N4,N5,divident(N4,N5,bsize),elemsetname='frp_t4_r')
mdoel1 = create_single_line_nodecoord(model1,N2,N6,divident(N2,N6,bsize),elemsetname='frp_t2_l')
mdoel1 = create_single_line_nodecoord(model1,N7,N4,divident(N7,N4,bsize),elemsetname='frp_t2_r')
#t1 = time.time() - t0
#print 'time to construct FRP layers %s ' % str(t1)
#t0 = time.time()
model1,a,b,c = sktretch_2dmesh(model1,24,2,ElemSetNameList=['frp_t1'],setname='plate_frp_t1')
model1,a,b,c = sktretch_2dmesh(model1,24,2,ElemSetNameList=['frp_t2_l','frp_t2_r'],setname='plate_frp_t2')
model1,a,b,c = sktretch_2dmesh(model1,24,2,ElemSetNameList=['frp_t3_l','frp_t3_r','frp_t3'],setname='plate_frp_t3')
model1,a,b,c = sktretch_2dmesh(model1,24,2,ElemSetNameList=['frp_t4_l','frp_t4_r'],setname='plate_frp_t4')
#t1 = time.time() - t0
#print 'time to Extrude FRP layers %s ' % str(t1)
# create top UHPC layer
#t0 = time.time()
model1 = create_3d_patch(model1,(0-bf/2.0,h-tf,0),(bsize,hsize,Lsize),(bf/bsize,tf/hsize,L/Lsize),setname='UHPC')
#t1 = time.time() - t0
#print 'time to construct UHPC %s ' % str(t1)
#t0 = time.time()
model1.sweep()
#t1 = time.time() - t0
#print 'time to sweep nodes %s ' % str(t1)
#t0 = time.time()
model1.nodelist.get_sortedcoordtable()
model1 = create_interface(model1,[-b1/2.0,h-tf,0],[-b1/2.0,h-tf1,0],2,24,setname='interface_left')
model1 = create_interface(model1,[0,h-tf,0],[0,h-tf1,0],2,24,setname='interface_center')
model1 = create_interface(model1,[b1/2.0,h-tf,0],[b1/2.0,h-tf1,0],2,24,setname='interface_right')
#t1 = time.time() - t0
#print 'time to construct interface %s ' % str(t1)
# add and assign property
model1 = add_property(model1)
model1.section('frp_t1','shell_section',{'thickness':t1})
model1.section('frp_t2','shell_section',{'thickness':t2})
model1.section('frp_t3','shell_section',{'thickness':t3})
model1.section('frp_t4','shell_section',{'thickness':t4})
model1.section('interface','interface2d',{})
model1.link_sec_prop('frp_t1','frp_t1')
model1.link_sec_prop('frp_t2','frp_t2')
model1.link_sec_prop('frp_t3','frp_t3')
model1.link_sec_prop('frp_t4','frp_t4')
model1.link_sec_prop('interface','interface')
model1.link_prop_conn('interface',setnamelist=['interface_left','interface_center','interface_right'])
model1.link_prop_conn('concrete',setnamelist=['UHPC'])
model1.link_prop_conn('frp_t1',setnamelist=['element_plate_frp_t1'])
model1.link_prop_conn('frp_t2',setnamelist=['element_plate_frp_t2'])
model1.link_prop_conn('frp_t3',setnamelist=['element_plate_frp_t3'])
model1.link_prop_conn('frp_t4',setnamelist=['element_plate_frp_t4'])
# create boundary conditions
leftbond = model1.nodelist.select_node_coord(rz=[0,0],ry=[0,0])
rightbond = model1.nodelist.select_node_coord(rz=[L,L],ry=[0,0])
centerload = model1.nodelist.select_node_coord(rz=[L/2.0,L/2.0],ry=[h,h])
centerlineload = model1.nodelist.select_node_coord(rx=[0,0],rz=[0,L],ry=[h-tf,h-tf])
middlenode = model1.nodelist.select_node_coord(rx=[0,0],rz=[L/2.0,L/2.0],ry=[0,0])
model1.nodeset('middlenode',{'nodelist':middlenode})
model1.nodeset('leftbond',{'nodelist':leftbond})
model1.nodeset('rightbond',{'nodelist':rightbond})
model1.nodeset('centerload',{'nodelist':centerload})
model1.nodeset('centerlineload',{'nodelist':centerlineload})
model1.table('loadtable',1,['time'],[[0,0],[1,1]])
model1.bond('leftbond',{'xyz':[1,1,1,0,0,0],'DOF':6,'setnamelist':['leftbond']})
model1.bond('rightbond',{'xyz':[0,1,1,0,0,0],'DOF':6,'setnamelist':['rightbond']})
model1.bond('support_z',{'xyz':[0,0,1,0,0,0],'DOF':6,'setnamelist':['centerlineload']})
model1.load('centerload',{'xyz':[0,1,0,0,0,0],'DOF':6,'scalar':-4,'setnamelist':['centerload'],'tabletag':'loadtable'})
# create Reb2
loadlinenode = model1.nodelist.select_node_coord(rz=[L/2.0,L/2.0],ry=[h,h])
loadlinecenter = model1.nodelist.select_node_coord(rz=[L/2.0,L/2.0],ry=[h,h],rx=[0,0])
# remove center node fron list
loadlinenode = loadlinenode.difference(loadlinecenter)
loadlinenode = list(loadlinenode)
loadlinecenter = list(loadlinecenter)
model1.nodaltie('rbe_load','marc_rbe2',{'tietype':'DY','tieid':1,'retnode':loadlinecenter[0],'tienodelist':loadlinenode})
model1.loadcase('loadcase1','static_arclength',{'boundarylist':['leftbond','centerload','rightbond','support_z'],'para':{'nstep':50}})
model1.job('job1','static_job',{'loadcaselist':['loadcase1'],'submit':True,'reqresultslist':['stress','total_strain','crack_strain','plastic_strain']})
# rotate
model1.nodelist.transform(ry=3.1415926/2.0)
exp1 = exporter(model1,'hybrid.proc','ex_Marc_dat')
exp1.export('default')
#t0 = time.time()
model1.modelsavetofile('hybrid.pydat')
