Ejemplos de addPositives en Python

Ejemplo n.º 1

Archivo: mechaslab.py Proyecto: Sciumo/SFACT

def addSlab(derivation, positives):
	"""Add slab."""
	copyShallow = derivation.xmlElement.getCopyShallow()
	copyShallow.attributeDictionary['path'] = [Vector3(), Vector3(0.0, 0.0, derivation.height)]
	extrudeDerivation = extrude.ExtrudeDerivation(copyShallow)
	beveledRectangle = getBeveledRectangle(derivation.bevel, -derivation.topRight)
	outsidePath = euclidean.getVector3Path(beveledRectangle)
	extrude.addPositives(extrudeDerivation, [outsidePath], positives)

Ejemplo n.º 2

Archivo: mechaslab.py Proyecto: CNCBASHER/skeinforge-1

def addSlab(derivation, positives):
	'Add slab.'
	copyShallow = derivation.xmlElement.getCopyShallow()
	copyShallow.attributeDictionary['path'] = [Vector3(), Vector3(0.0, 0.0, derivation.height)]
	extrudeDerivation = extrude.ExtrudeDerivation(copyShallow)
	beveledRectangle = getBeveledRectangle(derivation.bevel, -derivation.topRight)
	outsidePath = euclidean.getVector3Path(beveledRectangle)
	extrude.addPositives(extrudeDerivation, [outsidePath], positives)

Ejemplo n.º 3

Archivo: linear_bearing_cage.py Proyecto: greenarrow/skeinforgeGit

def addCage(derivation, height, negatives, positives):
	'Add linear bearing cage.'
	copyShallow = derivation.xmlElement.getCopyShallow()
	copyShallow.attributeDictionary['path'] = [Vector3(), Vector3(0.0, 0.0, height)]
	extrudeDerivation = extrude.ExtrudeDerivation(copyShallow)
	roundedExtendedRectangle = getRoundedExtendedRectangle(derivation.demiwidth, derivation.rectangleCenterX, 14)
	outsidePath = euclidean.getVector3Path(roundedExtendedRectangle)
	extrude.addPositives(extrudeDerivation, positives, [outsidePath])
	for bearingCenterX in derivation.bearingCenterXs:
		addNegativeSphere(derivation, negatives, bearingCenterX)

Ejemplo n.º 4

Archivo: linear_bearing_cage.py Proyecto: zaubara/Curation

def addCage(derivation, height, negatives, positives):
	'Add linear bearing cage.'
	copyShallow = derivation.elementNode.getCopyShallow()
	copyShallow.attributes['path'] = [Vector3(), Vector3(0.0, 0.0, height)]
	extrudeDerivation = extrude.ExtrudeDerivation(copyShallow)
	roundedExtendedRectangle = getRoundedExtendedRectangle(derivation.demiwidth, derivation.rectangleCenterX, 14)
	outsidePath = euclidean.getVector3Path(roundedExtendedRectangle)
	extrude.addPositives(extrudeDerivation, [outsidePath], positives)
	for bearingCenterX in derivation.bearingCenterXs:
		addNegativeSphere(derivation, negatives, bearingCenterX)

Ejemplo n.º 5

Archivo: linear_bearing_cage.py Proyecto: greenarrow/skeinforgeGit

def addGroove(derivation, negatives):
	'Add groove on each side of cage.'
	copyShallow = derivation.xmlElement.getCopyShallow()
	extrude.setXMLElementToEndStart(Vector3(-derivation.demilength), Vector3(derivation.demilength), copyShallow)
	extrudeDerivation = extrude.ExtrudeDerivation(copyShallow)
	bottom = derivation.demiheight - 0.5 * derivation.grooveWidth
	outside = derivation.demiwidth
	top = derivation.demiheight
	leftGroove = [
		complex(-outside, bottom),
		complex(-derivation.innerDemiwidth, derivation.demiheight),
		complex(-outside, top)]
	rightGroove = [
		complex(outside, top),
		complex(derivation.innerDemiwidth, derivation.demiheight),
		complex(outside, bottom)]
	groovesComplex = [leftGroove, rightGroove]
	groovesVector3 = euclidean.getVector3Paths(groovesComplex)
	extrude.addPositives(extrudeDerivation, negatives, groovesVector3)

Ejemplo n.º 6

Archivo: mechaslab.py Proyecto: CNCBASHER/skeinforge-1

def addGroove(derivation, negatives):
	'Add groove on each side of cage.'
	copyShallow = derivation.xmlElement.getCopyShallow()
	extrude.setXMLElementToEndStart(Vector3(-derivation.demilength), Vector3(derivation.demilength), copyShallow)
	extrudeDerivation = extrude.ExtrudeDerivation(copyShallow)
	bottom = derivation.demiheight - 0.5 * derivation.grooveWidth
	outside = derivation.demiwidth
	top = derivation.demiheight
	leftGroove = [
		complex(-outside, bottom),
		complex(-derivation.innerDemiwidth, derivation.demiheight),
		complex(-outside, top)]
	rightGroove = [
		complex(outside, top),
		complex(derivation.innerDemiwidth, derivation.demiheight),
		complex(outside, bottom)]
	groovesComplex = [leftGroove, rightGroove]
	groovesVector3 = euclidean.getVector3Paths(groovesComplex)
	extrude.addPositives(extrudeDerivation, groovesVector3, negatives)