def __init__(self, uhd_address, options):
gr.top_block.__init__(self)
self.uhd_addr = uhd_address
self.freq = options.freq
self.samp_rate = options.samp_rate
self.gain = options.gain
self.threshold = options.threshold
self.trigger = options.trigger
self.uhd_src = uhd.single_usrp_source(
device_addr=self.uhd_addr, stream_args=uhd.stream_args('fc32'))
self.uhd_src.set_samp_rate(self.samp_rate)
self.uhd_src.set_center_freq(self.freq, 0)
self.uhd_src.set_gain(self.gain, 0)
taps = firdes.low_pass_2(1, 1, 0.4, 0.1, 60)
self.chanfilt = gr.fir_filter_ccc(10, taps)
self.tagger = gr.burst_tagger(gr.sizeof_gr_complex)
# Dummy signaler to collect a burst on known periods
data = 1000 * [
0,
] + 1000 * [
1,
]
self.signal = gr.vector_source_s(data, True)
# Energy detector to get signal burst
## use squelch to detect energy
self.det = gr.simple_squelch_cc(self.threshold, 0.01)
## convert to mag squared (float)
self.c2m = gr.complex_to_mag_squared()
## average to debounce
self.avg = gr.single_pole_iir_filter_ff(0.01)
## rescale signal for conversion to short
self.scale = gr.multiply_const_ff(2**16)
## signal input uses shorts
self.f2s = gr.float_to_short()
# Use file sink burst tagger to capture bursts
self.fsnk = gr.tagged_file_sink(gr.sizeof_gr_complex, self.samp_rate)
##################################################
# Connections
##################################################
self.connect((self.uhd_src, 0), (self.tagger, 0))
self.connect((self.tagger, 0), (self.fsnk, 0))
if self.trigger:
# Connect a dummy signaler to the burst tagger
self.connect((self.signal, 0), (self.tagger, 1))
else:
# Connect an energy detector signaler to the burst tagger
self.connect(self.uhd_src, self.det)
self.connect(self.det, self.c2m, self.avg, self.scale, self.f2s)
self.connect(self.f2s, (self.tagger, 1))
def __init__(self, uhd_address, options):
gr.top_block.__init__(self)
self.uhd_addr = uhd_address
self.freq = options.freq
self.samp_rate = options.samp_rate
self.gain = options.gain
self.threshold = options.threshold
self.trigger = options.trigger
self.uhd_src = uhd.single_usrp_source(
device_addr=self.uhd_addr,
io_type=uhd.io_type_t.COMPLEX_FLOAT32,
num_channels=1,
)
self.uhd_src.set_samp_rate(self.samp_rate)
self.uhd_src.set_center_freq(self.freq, 0)
self.uhd_src.set_gain(self.gain, 0)
taps = firdes.low_pass_2(1, 1, 0.4, 0.1, 60)
self.chanfilt = gr.fir_filter_ccc(10, taps)
self.tagger = gr.burst_tagger(gr.sizeof_gr_complex)
# Dummy signaler to collect a burst on known periods
data = 1000*[0,] + 1000*[1,]
self.signal = gr.vector_source_s(data, True)
# Energy detector to get signal burst
## use squelch to detect energy
self.det = gr.simple_squelch_cc(self.threshold, 0.01)
## convert to mag squared (float)
self.c2m = gr.complex_to_mag_squared()
## average to debounce
self.avg = gr.single_pole_iir_filter_ff(0.01)
## rescale signal for conversion to short
self.scale = gr.multiply_const_ff(2**16)
## signal input uses shorts
self.f2s = gr.float_to_short()
# Use file sink burst tagger to capture bursts
self.fsnk = gr.tagged_file_sink(gr.sizeof_gr_complex, self.samp_rate)
##################################################
# Connections
##################################################
self.connect((self.uhd_src, 0), (self.tagger, 0))
self.connect((self.tagger, 0), (self.fsnk, 0))
if self.trigger:
# Connect a dummy signaler to the burst tagger
self.connect((self.signal, 0), (self.tagger, 1))
else:
# Connect an energy detector signaler to the burst tagger
self.connect(self.uhd_src, self.det)
self.connect(self.det, self.c2m, self.avg, self.scale, self.f2s)
self.connect(self.f2s, (self.tagger, 1))
def _setup_top_block(self):
self.tb = gr.top_block()
samp_rate = 96000
oversample = 10
center_freq = 868.280e6
# Radio receiver, initial downsampling
args = str("nchan=1 rtl=%s,buffers=16,offset_tune=1" % self.device)
osmosdr_source = osmosdr.source_c(args=args)
osmosdr_source.set_sample_rate(samp_rate*oversample)
osmosdr_source.set_center_freq(center_freq, 0)
osmosdr_source.set_freq_corr(0, 0)
osmosdr_source.set_gain_mode(1, 0)
osmosdr_source.set_gain(0, 0)
low_pass_filter = gr.fir_filter_ccf(oversample,
firdes.low_pass(1, samp_rate*oversample, 90e3, 8e3, firdes.WIN_HAMMING, 6.76))
self.tb.connect((osmosdr_source, 0), (low_pass_filter, 0))
# Squelch
self.noise_probe = gr.probe_avg_mag_sqrd_c(0, 1.0/samp_rate/1e2)
self.squelch = gr.simple_squelch_cc(self.noise_level, 1)
noise_probe_thread = threading.Thread(target=self._noise_probe_thread)
noise_probe_thread.start()
self.threads.append(noise_probe_thread)
self.tb.connect((low_pass_filter, 0), (self.noise_probe, 0))
self.tb.connect((low_pass_filter, 0), (self.squelch, 0))
# FM demodulation
quadrature_demod = gr.quadrature_demod_cf(1)
self.tb.connect((self.squelch, 0), (quadrature_demod, 0))
# Binary slicing, transformation into capture-compatible format
add_offset = gr.add_const_vff((-1e-3, ))
binary_slicer = digital.binary_slicer_fb()
char_to_float = gr.char_to_float(1, 1)
multiply_const = gr.multiply_const_vff((255, ))
float_to_uchar = gr.float_to_uchar()
pipe_sink = gr.file_sink(gr.sizeof_char*1, self.pipe)
pipe_sink.set_unbuffered(False)
self.tb.connect((quadrature_demod, 0), (add_offset, 0))
self.tb.connect((add_offset, 0), (binary_slicer, 0))
self.tb.connect((binary_slicer, 0), (char_to_float, 0))
self.tb.connect((char_to_float, 0), (multiply_const, 0))
self.tb.connect((multiply_const, 0), (float_to_uchar, 0))
self.tb.connect((float_to_uchar, 0), (pipe_sink, 0))
def __init__(self):
gr.top_block.__init__(self, "FM Receiver")
##################################################
# Variables
##################################################
self.samp_rate = samp_rate = 96000
self.xlate_filter_taps = xlate_filter_taps = firdes.low_pass(1, samp_rate, 48000, 5000, firdes.WIN_HAMMING, 6.76)
self.sql_lev = sql_lev = -100
self.rf_gain = rf_gain = 20
self.freq = freq = 144800000
self.af_gain = af_gain = 2
self.sat_file_name = sat_file_name = "Undefined"
##################################################
# Blocks
##################################################
self.xlating_fir_filter = gr.freq_xlating_fir_filter_ccc(1, (xlate_filter_taps), 0, samp_rate)
self.nbfm_normal = blks2.nbfm_rx(
audio_rate=48000,
quad_rate=96000,
tau=75e-6,
max_dev=5e3,
)
self.low_pass_filter = gr.fir_filter_ccf(1, firdes.low_pass(
1, samp_rate, 12500, 1500, firdes.WIN_HAMMING, 6.76))
self.gr_simple_squelch_cc_0 = gr.simple_squelch_cc(sql_lev, 1)
self.gr_multiply_const_vxx_1 = gr.multiply_const_vff((af_gain, ))
self.fcd_source_c_1 = fcd.source_c("hw:1")
self.fcd_source_c_1.set_freq(freq)
self.fcd_source_c_1.set_freq_corr(-32)
self.audio_sink = audio.sink(48000, "", True)
self.wavfile_sink = gr.wavfile_sink(self.sat_file_name, 1, 11025, 16)
self.blks2_rational_resampler_xxx_0 = blks2.rational_resampler_fff(
interpolation=11025,
decimation=48000,
taps=None,
fractional_bw=None,
)
##################################################
# Connections
##################################################
self.connect((self.xlating_fir_filter, 0), (self.low_pass_filter, 0))
self.connect((self.low_pass_filter, 0), (self.gr_simple_squelch_cc_0, 0))
self.connect((self.gr_multiply_const_vxx_1, 0), (self.audio_sink, 1))
self.connect((self.gr_multiply_const_vxx_1, 0), (self.audio_sink, 0))
self.connect((self.gr_simple_squelch_cc_0, 0), (self.nbfm_normal, 0))
self.connect((self.nbfm_normal, 0), (self.gr_multiply_const_vxx_1, 0))
self.connect((self.fcd_source_c_1, 0), (self.xlating_fir_filter, 0))
self.connect((self.nbfm_normal, 0), (self.blks2_rational_resampler_xxx_0, 0))
self.connect((self.blks2_rational_resampler_xxx_0, 0), (self.wavfile_sink, 0))
def __init__(self):
gr.top_block.__init__(self, "CW/SSB Receiver")
##################################################
# Variables
##################################################
self.samp_rate = samp_rate = 96000
self.xlate_filter_taps = xlate_filter_taps = firdes.low_pass(1, samp_rate, 48000, 5000, firdes.WIN_HAMMING, 6.76)
self.sql_lev = sql_lev = -100
self.rf_gain = rf_gain = 20
self.pass_trans = pass_trans = 600
self.pass_low = pass_low = 300
self.pass_high = pass_high = 1200
self.freq = freq = 144800000
self.af_gain = af_gain = 5
self.sat_file_name = sat_file_name = "Undefined"
##################################################
# Blocks
##################################################
self.xlating_fir_filter = gr.freq_xlating_fir_filter_ccc(1, (xlate_filter_taps), 0, samp_rate)
self.gr_simple_squelch_cc_0 = gr.simple_squelch_cc(sql_lev, 1)
self.gr_multiply_const_vxx_0 = gr.multiply_const_vff((af_gain, ))
self.gr_complex_to_real_0 = gr.complex_to_real(1)
self.gr_agc2_xx_0 = gr.agc2_cc(1e-1, 20.8e-6, 0.3, 1.0, 0.0)
self.fcd_source_c_1 = fcd.source_c("hw:1")
self.fcd_source_c_1.set_freq(freq)
self.fcd_source_c_1.set_freq_corr(-10)
self.band_pass_filter_0 = gr.fir_filter_ccf(2, firdes.band_pass(
1, samp_rate, pass_low, pass_high, pass_trans, firdes.WIN_HAMMING, 6.76))
self.audio_sink = audio.sink(48000, "", True)
self.wavfile_sink = gr.wavfile_sink(self.sat_file_name, 1, 11025, 16)
self.blks2_rational_resampler_xxx_0 = blks2.rational_resampler_fff(
interpolation=11025,
decimation=48000,
taps=None,
fractional_bw=None,
)
##################################################
# Connections
##################################################
self.connect((self.fcd_source_c_1, 0), (self.xlating_fir_filter, 0))
self.connect((self.xlating_fir_filter, 0), (self.gr_simple_squelch_cc_0, 0))
self.connect((self.band_pass_filter_0, 0), (self.gr_agc2_xx_0, 0))
self.connect((self.gr_complex_to_real_0, 0), (self.gr_multiply_const_vxx_0, 0))
self.connect((self.gr_agc2_xx_0, 0), (self.gr_complex_to_real_0, 0))
self.connect((self.gr_simple_squelch_cc_0, 0), (self.band_pass_filter_0, 0))
self.connect((self.gr_multiply_const_vxx_0, 0), (self.audio_sink, 0))
self.connect((self.gr_multiply_const_vxx_0, 0), (self.audio_sink, 1))
self.connect((self.gr_complex_to_real_0, 0), (self.blks2_rational_resampler_xxx_0, 0))
self.connect((self.blks2_rational_resampler_xxx_0, 0), (self.wavfile_sink, 0))
def __init__(self):
gr.top_block.__init__(self, "FM Receiver")
##################################################
# Variables
##################################################
self.samp_rate = samp_rate = 96000
self.xlate_filter_taps = xlate_filter_taps = firdes.low_pass(1, samp_rate, 48000, 5000, firdes.WIN_HAMMING, 6.76)
self.sql_lev = sql_lev = -100
self.rf_gain = rf_gain = 20
self.freq = freq = 144800000
self.af_gain = af_gain = 2
##################################################
# Blocks
##################################################
self.xlating_fir_filter = gr.freq_xlating_fir_filter_ccc(1, (xlate_filter_taps), 0, samp_rate)
self.nbfm_normal = blks2.nbfm_rx(
audio_rate=48000,
quad_rate=96000,
tau=75e-6,
max_dev=5e3,
)
self.low_pass_filter = gr.fir_filter_ccf(1, firdes.low_pass(
1, samp_rate, 12500, 1500, firdes.WIN_HAMMING, 6.76))
self.gr_simple_squelch_cc_0 = gr.simple_squelch_cc(sql_lev, 1)
self.gr_multiply_const_vxx_1 = gr.multiply_const_vff((af_gain, ))
self.fcd_source_c_1 = fcd.source_c("hw:1")
self.fcd_source_c_1.set_freq(freq)
self.fcd_source_c_1.set_freq_corr(-32)
self.audio_sink = audio.sink(48000, "", True)
##################################################
# Connections
##################################################
self.connect((self.xlating_fir_filter, 0), (self.low_pass_filter, 0))
self.connect((self.low_pass_filter, 0), (self.gr_simple_squelch_cc_0, 0))
self.connect((self.gr_multiply_const_vxx_1, 0), (self.audio_sink, 1))
self.connect((self.gr_multiply_const_vxx_1, 0), (self.audio_sink, 0))
self.connect((self.gr_simple_squelch_cc_0, 0), (self.nbfm_normal, 0))
self.connect((self.nbfm_normal, 0), (self.gr_multiply_const_vxx_1, 0))
self.connect((self.fcd_source_c_1, 0), (self.xlating_fir_filter, 0))
def __init__(self):
gr.top_block.__init__(self, "CW/SSB Receiver")
##################################################
# Variables
##################################################
self.samp_rate = samp_rate = 96000
self.xlate_filter_taps = xlate_filter_taps = firdes.low_pass(1, samp_rate, 48000, 5000, firdes.WIN_HAMMING, 6.76)
self.sql_lev = sql_lev = -100
self.rf_gain = rf_gain = 20
self.pass_trans = pass_trans = 600
self.pass_low = pass_low = 300
self.pass_high = pass_high = 1200
self.freq = freq = 144800000
self.af_gain = af_gain = 5
##################################################
# Blocks
##################################################
self.xlating_fir_filter = gr.freq_xlating_fir_filter_ccc(1, (xlate_filter_taps), 0, samp_rate)
self.gr_simple_squelch_cc_0 = gr.simple_squelch_cc(sql_lev, 1)
self.gr_multiply_const_vxx_0 = gr.multiply_const_vff((af_gain, ))
self.gr_complex_to_real_0 = gr.complex_to_real(1)
self.gr_agc2_xx_0 = gr.agc2_cc(1e-1, 20.8e-6, 0.3, 1.0, 0.0)
self.fcd_source_c_1 = fcd.source_c("hw:1")
self.fcd_source_c_1.set_freq(freq)
self.fcd_source_c_1.set_freq_corr(-10)
self.band_pass_filter_0 = gr.fir_filter_ccf(2, firdes.band_pass(
1, samp_rate, pass_low, pass_high, pass_trans, firdes.WIN_HAMMING, 6.76))
self.audio_sink = audio.sink(48000, "", True)
##################################################
# Connections
##################################################
self.connect((self.fcd_source_c_1, 0), (self.xlating_fir_filter, 0))
self.connect((self.xlating_fir_filter, 0), (self.gr_simple_squelch_cc_0, 0))
self.connect((self.band_pass_filter_0, 0), (self.gr_agc2_xx_0, 0))
self.connect((self.gr_complex_to_real_0, 0), (self.gr_multiply_const_vxx_0, 0))
self.connect((self.gr_agc2_xx_0, 0), (self.gr_complex_to_real_0, 0))
self.connect((self.gr_simple_squelch_cc_0, 0), (self.band_pass_filter_0, 0))
self.connect((self.gr_multiply_const_vxx_0, 0), (self.audio_sink, 0))
self.connect((self.gr_multiply_const_vxx_0, 0), (self.audio_sink, 1))
def __init__(self, args, spec, antenna, gain, audio_output):
gr.hier_block2.__init__(self, "receive_path",
gr.io_signature(0, 0, 0), # Input signature
gr.io_signature(0, 0, 0)) # Output signature
self.u = uhd.usrp_source(device_addr=args,
io_type=uhd.io_type.COMPLEX_FLOAT32,
num_channels=1)
self.if_rate = 256e3
self.quad_rate = 64e3
self.audio_rate = 32e3
self.u.set_samp_rate(self.if_rate)
dev_rate = self.u.get_samp_rate()
# Create filter to get actual channel we want
nfilts = 32
chan_coeffs = gr.firdes.low_pass (nfilts, # gain
nfilts*dev_rate, # sampling rate
8e3, # low pass cutoff freq
2e3, # width of trans. band
gr.firdes.WIN_HANN) # filter type
rrate = self.quad_rate / dev_rate
self.resamp = blks2.pfb_arb_resampler_ccf(rrate, chan_coeffs, nfilts)
if USE_SIMPLE_SQUELCH:
self.squelch = gr.simple_squelch_cc(20)
else:
self.squelch = blks2.standard_squelch(self.audio_rate)
# instantiate the guts of the single channel receiver
self.fmrx = blks2.nbfm_rx(self.audio_rate, self.quad_rate)
# audio gain / mute block
self._audio_gain = gr.multiply_const_ff(1.0)
# sound card as final sink
audio_sink = audio.sink (int(self.audio_rate), audio_output)
# now wire it all together
if USE_SIMPLE_SQUELCH:
self.connect (self.u, self.resamp, self.squelch, self.fmrx,
self._audio_gain, audio_sink)
else:
self.connect (self.u, self.resamp, self.fmrx, self.squelch,
self._audio_gain, audio_sink)
if gain is None:
# if no gain was specified, use the mid-point in dB
g = self.u.get_gain_range()
gain = float(g.start()+g.stop())/2
self.set_gain(gain)
v = self.volume_range()
self.set_volume((v[0]+v[1])/2)
s = self.squelch_range()
self.set_squelch((s[0]+s[1])/2)
# Set the subdevice spec
if(spec):
self.u.set_subdev_spec(spec, 0)
# Set the antenna
if(antenna):
self.u.set_antenna(antenna, 0)
def __init__(self, demod_class, rx_callback, options):
gr.hier_block2.__init__(self, "receive_path",
gr.io_signature(0, 0, 0), # Input signature
gr.io_signature(0, 0, 0)) # Output signature
options = copy.copy(options) # make a copy so we can destructively modify
self._verbose = options.verbose
self._rx_freq = options.rx_freq # receiver's center frequency
self._rx_gain = options.rx_gain # receiver's gain
self._rx_subdev_spec = options.rx_subdev_spec # daughterboard to use
self._bitrate = options.bitrate # desired bit rate
self._decim = options.decim # Decimating rate for the USRP (prelim)
self._samples_per_symbol = options.samples_per_symbol # desired samples/symbol
self._fusb_block_size = options.fusb_block_size # usb info for USRP
self._fusb_nblocks = options.fusb_nblocks # usb info for USRP
self._rx_callback = rx_callback # this callback is fired when there's a packet available
self._demod_class = demod_class # the demodulator_class we're using
if self._rx_freq is None:
sys.stderr.write("-f FREQ or --freq FREQ or --rx-freq FREQ must be specified\n")
raise SystemExit
# Set up USRP source; also adjusts decim, samples_per_symbol, and bitrate
self._setup_usrp_source()
g = self.subdev.gain_range()
if options.show_rx_gain_range:
print "Rx Gain Range: minimum = %g, maximum = %g, step size = %g" \
% (g[0], g[1], g[2])
self.set_gain(options.rx_gain)
self.set_auto_tr(True) # enable Auto Transmit/Receive switching
# Set RF frequency
ok = self.set_freq(self._rx_freq)
if not ok:
print "Failed to set Rx frequency to %s" % (eng_notation.num_to_str(self._rx_freq))
raise ValueError, eng_notation.num_to_str(self._rx_freq)
# copy the final answers back into options for use by demodulator
options.samples_per_symbol = self._samples_per_symbol
options.bitrate = self._bitrate
options.decim = self._decim
# Get demod_kwargs
demod_kwargs = self._demod_class.extract_kwargs_from_options(options)
# Design filter to get actual channel we want
sw_decim = 1
chan_coeffs = gr.firdes.low_pass (1.0, # gain
sw_decim * self._samples_per_symbol, # sampling rate
1.0, # midpoint of trans. band
0.5, # width of trans. band
gr.firdes.WIN_HANN) # filter type
# Decimating channel filter
# complex in and out, float taps
self.chan_filt = gr.fft_filter_ccc(sw_decim, chan_coeffs)
#self.chan_filt = gr.fir_filter_ccf(sw_decim, chan_coeffs)
# receiver
self.packet_receiver = \
blks2.demod_pkts(self._demod_class(**demod_kwargs),
access_code=None,
callback=self._rx_callback,
threshold=-1)
# Carrier Sensing Blocks
alpha = 0.001
thresh = 30 # in dB, will have to adjust
self.sequelcher = gr.simple_squelch_cc(45)
if options.log_rx_power == True:
self.probe = gr.probe_avg_mag_sqrd_cf(thresh,alpha)
self.power_sink = gr.file_sink(gr.sizeof_float, "rxpower.dat")
self.connect(self.chan_filt, self.probe, self.power_sink)
else:
self.probe = gr.probe_avg_mag_sqrd_c(thresh,alpha)
#self.connect(self.chan_filt, self.sequelcher, self.probe)
# Display some information about the setup
if self._verbose:
self._print_verbage()
#filter the noise and pass only the transmitted data
#file_source = gr.file_source(gr.sizeof_gr_complex,"modulated_data.dat")
#self.connect(self.chan_filt,file_sink)
self.connect(self.u, self.chan_filt,self.sequelcher, self.packet_receiver)
def __init__(self):
grc_wxgui.top_block_gui.__init__(self, title="Amaviation Agc")
_icon_path = "/usr/share/icons/hicolor/32x32/apps/gnuradio-grc.png"
self.SetIcon(wx.Icon(_icon_path, wx.BITMAP_TYPE_ANY))
##################################################
# Variables
##################################################
self.sql_threshold = sql_threshold = -30
self.samp_rate = samp_rate = 1000000
self.frq_offset = frq_offset = 0
self.base_frq = base_frq = 131725000
##################################################
# Blocks
##################################################
_sql_threshold_sizer = wx.BoxSizer(wx.VERTICAL)
self._sql_threshold_text_box = forms.text_box(
parent=self.GetWin(),
sizer=_sql_threshold_sizer,
value=self.sql_threshold,
callback=self.set_sql_threshold,
label="Squelch Threshold",
converter=forms.float_converter(),
proportion=0,
)
self._sql_threshold_slider = forms.slider(
parent=self.GetWin(),
sizer=_sql_threshold_sizer,
value=self.sql_threshold,
callback=self.set_sql_threshold,
minimum=-100,
maximum=0,
num_steps=100,
style=wx.SL_HORIZONTAL,
cast=float,
proportion=1,
)
self.Add(_sql_threshold_sizer)
_frq_offset_sizer = wx.BoxSizer(wx.VERTICAL)
self._frq_offset_text_box = forms.text_box(
parent=self.GetWin(),
sizer=_frq_offset_sizer,
value=self.frq_offset,
callback=self.set_frq_offset,
label="Frequency Offset",
converter=forms.float_converter(),
proportion=0,
)
self._frq_offset_slider = forms.slider(
parent=self.GetWin(),
sizer=_frq_offset_sizer,
value=self.frq_offset,
callback=self.set_frq_offset,
minimum=-100000,
maximum=100000,
num_steps=1000,
style=wx.SL_HORIZONTAL,
cast=float,
proportion=1,
)
self.Add(_frq_offset_sizer)
self._base_frq_text_box = forms.text_box(
parent=self.GetWin(),
value=self.base_frq,
callback=self.set_base_frq,
label="Base frequency",
converter=forms.float_converter(),
)
self.Add(self._base_frq_text_box)
self.wxgui_fftsink2_0 = fftsink2.fft_sink_c(
self.GetWin(),
baseband_freq=0,
y_per_div=10,
y_divs=10,
ref_level=0,
ref_scale=2.0,
sample_rate=samp_rate,
fft_size=1024,
fft_rate=15,
average=False,
avg_alpha=None,
title="FFT Plot",
peak_hold=False,
)
self.Add(self.wxgui_fftsink2_0.win)
self.rtl2832_source_0 = baz.rtl_source_c(defer_creation=True)
self.rtl2832_source_0.set_verbose(True)
self.rtl2832_source_0.set_vid(0x0)
self.rtl2832_source_0.set_pid(0x0)
self.rtl2832_source_0.set_tuner_name("")
self.rtl2832_source_0.set_default_timeout(0)
self.rtl2832_source_0.set_use_buffer(True)
self.rtl2832_source_0.set_fir_coefficients(([]))
if self.rtl2832_source_0.create() == False:
raise Exception(
"Failed to create RTL2832 Source: rtl2832_source_0")
self.rtl2832_source_0.set_bandwidth(300000)
self.rtl2832_source_0.set_sample_rate(samp_rate)
self.rtl2832_source_0.set_frequency(base_frq + frq_offset)
self.rtl2832_source_0.set_gain_mode("sensitive")
self.rtl2832_source_0.set_auto_gain_mode(False)
self.rtl2832_source_0.set_relative_gain(True)
self.rtl2832_source_0.set_gain(30)
self.gr_simple_squelch_cc_0 = gr.simple_squelch_cc(
sql_threshold, 0.0001)
self.gr_agc2_xx_0 = gr.agc2_cc(100e-3, 200e-3, 1.0, 1.0, 2.0)
self.blks2_rational_resampler_xxx_0 = blks2.rational_resampler_ccc(
interpolation=48,
decimation=1000,
taps=None,
fractional_bw=None,
)
self.blks2_am_demod_cf_0 = blks2.am_demod_cf(
channel_rate=48000,
audio_decim=1,
audio_pass=5000,
audio_stop=5500,
)
self.audio_sink_0 = audio.sink(48000, "pulse", True)
##################################################
# Connections
##################################################
self.connect((self.rtl2832_source_0, 0), (self.wxgui_fftsink2_0, 0))
self.connect((self.blks2_am_demod_cf_0, 0), (self.audio_sink_0, 0))
self.connect((self.blks2_rational_resampler_xxx_0, 0),
(self.gr_simple_squelch_cc_0, 0))
self.connect((self.gr_simple_squelch_cc_0, 0), (self.gr_agc2_xx_0, 0))
self.connect((self.gr_agc2_xx_0, 0), (self.blks2_am_demod_cf_0, 0))
self.connect((self.rtl2832_source_0, 0),
(self.blks2_rational_resampler_xxx_0, 0))
def __init__(self, subdev_spec, gain, audio_output):
gr.hier_block2.__init__(
self,
"receive_path",
gr.io_signature(0, 0, 0), # Input signature
gr.io_signature(0, 0, 0)) # Output signature
self.u = usrp.source_c()
adc_rate = self.u.adc_rate()
self.if_rate = 256e3 # 256 kS/s
usrp_decim = int(adc_rate // self.if_rate)
if_decim = 4
self.u.set_decim_rate(usrp_decim)
self.quad_rate = self.if_rate // if_decim # 64 kS/s
audio_decim = 2
self.audio_rate = self.quad_rate // audio_decim # 32 kS/s
if subdev_spec is None:
subdev_spec = usrp.pick_rx_subdevice(self.u)
self.subdev = usrp.selected_subdev(self.u, subdev_spec)
print "Using RX d'board %s" % (self.subdev.side_and_name(), )
self.u.set_mux(usrp.determine_rx_mux_value(self.u, subdev_spec))
# Create filter to get actual channel we want
chan_coeffs = gr.firdes.low_pass(
1.0, # gain
self.if_rate, # sampling rate
8e3, # low pass cutoff freq
2e3, # width of trans. band
gr.firdes.WIN_HANN) # filter type
print "len(rx_chan_coeffs) =", len(chan_coeffs)
# Decimating Channel filter with frequency translation
# complex in and out, float taps
self.ddc = gr.freq_xlating_fir_filter_ccf(
if_decim, # decimation rate
chan_coeffs, # taps
0, # frequency translation amount
self.if_rate) # input sample rate
if USE_SIMPLE_SQUELCH:
self.squelch = gr.simple_squelch_cc(20)
else:
self.squelch = blks2.standard_squelch(self.audio_rate)
# instantiate the guts of the single channel receiver
self.fmrx = blks2.nbfm_rx(self.audio_rate, self.quad_rate)
# audio gain / mute block
self._audio_gain = gr.multiply_const_ff(1.0)
# sound card as final sink
audio_sink = audio.sink(int(self.audio_rate), audio_output)
# now wire it all together
if USE_SIMPLE_SQUELCH:
self.connect(self.u, self.ddc, self.squelch, self.fmrx,
self._audio_gain, audio_sink)
else:
self.connect(self.u, self.ddc, self.fmrx, self.squelch,
self._audio_gain, audio_sink)
if gain is None:
# if no gain was specified, use the mid-point in dB
g = self.subdev.gain_range()
gain = float(g[0] + g[1]) / 2
self.set_gain(gain)
v = self.volume_range()
self.set_volume((v[0] + v[1]) / 2)
s = self.squelch_range()
self.set_squelch((s[0] + s[1]) / 2)
def __init__(self, args, spec, antenna, gain, audio_output):
gr.hier_block2.__init__(
self,
"receive_path",
gr.io_signature(0, 0, 0), # Input signature
gr.io_signature(0, 0, 0)) # Output signature
self.u = uhd.usrp_source(device_addr=args,
stream_args=uhd.stream_args('fc32'))
self.if_rate = 256e3
self.quad_rate = 64e3
self.audio_rate = 32e3
self.u.set_samp_rate(self.if_rate)
dev_rate = self.u.get_samp_rate()
# Create filter to get actual channel we want
nfilts = 32
chan_coeffs = gr.firdes.low_pass(
nfilts, # gain
nfilts * dev_rate, # sampling rate
8e3, # low pass cutoff freq
2e3, # width of trans. band
gr.firdes.WIN_HANN) # filter type
rrate = self.quad_rate / dev_rate
self.resamp = blks2.pfb_arb_resampler_ccf(rrate, chan_coeffs, nfilts)
if USE_SIMPLE_SQUELCH:
self.squelch = gr.simple_squelch_cc(20)
else:
self.squelch = blks2.standard_squelch(self.audio_rate)
# instantiate the guts of the single channel receiver
self.fmrx = blks2.nbfm_rx(self.audio_rate, self.quad_rate)
# audio gain / mute block
self._audio_gain = gr.multiply_const_ff(1.0)
# sound card as final sink
audio_sink = audio.sink(int(self.audio_rate), audio_output)
# now wire it all together
if USE_SIMPLE_SQUELCH:
self.connect(self.u, self.resamp, self.squelch, self.fmrx,
self._audio_gain, audio_sink)
else:
self.connect(self.u, self.resamp, self.fmrx, self.squelch,
self._audio_gain, audio_sink)
if gain is None:
# if no gain was specified, use the mid-point in dB
g = self.u.get_gain_range()
gain = float(g.start() + g.stop()) / 2
self.set_gain(gain)
v = self.volume_range()
self.set_volume((v[0] + v[1]) / 2)
s = self.squelch_range()
self.set_squelch((s[0] + s[1]) / 2)
# Set the subdevice spec
if (spec):
self.u.set_subdev_spec(spec, 0)
# Set the antenna
if (antenna):
self.u.set_antenna(antenna, 0)
def __init__(self):
grc_wxgui.top_block_gui.__init__(self, title="Amaviation Agc")
_icon_path = "/usr/share/icons/hicolor/32x32/apps/gnuradio-grc.png"
self.SetIcon(wx.Icon(_icon_path, wx.BITMAP_TYPE_ANY))
##################################################
# Variables
##################################################
self.sql_threshold = sql_threshold = -30
self.samp_rate = samp_rate = 1000000
self.frq_offset = frq_offset = 0
self.base_frq = base_frq = 131725000
##################################################
# Blocks
##################################################
_sql_threshold_sizer = wx.BoxSizer(wx.VERTICAL)
self._sql_threshold_text_box = forms.text_box(
parent=self.GetWin(),
sizer=_sql_threshold_sizer,
value=self.sql_threshold,
callback=self.set_sql_threshold,
label="Squelch Threshold",
converter=forms.float_converter(),
proportion=0,
)
self._sql_threshold_slider = forms.slider(
parent=self.GetWin(),
sizer=_sql_threshold_sizer,
value=self.sql_threshold,
callback=self.set_sql_threshold,
minimum=-100,
maximum=0,
num_steps=100,
style=wx.SL_HORIZONTAL,
cast=float,
proportion=1,
)
self.Add(_sql_threshold_sizer)
_frq_offset_sizer = wx.BoxSizer(wx.VERTICAL)
self._frq_offset_text_box = forms.text_box(
parent=self.GetWin(),
sizer=_frq_offset_sizer,
value=self.frq_offset,
callback=self.set_frq_offset,
label="Frequency Offset",
converter=forms.float_converter(),
proportion=0,
)
self._frq_offset_slider = forms.slider(
parent=self.GetWin(),
sizer=_frq_offset_sizer,
value=self.frq_offset,
callback=self.set_frq_offset,
minimum=-100000,
maximum=100000,
num_steps=1000,
style=wx.SL_HORIZONTAL,
cast=float,
proportion=1,
)
self.Add(_frq_offset_sizer)
self._base_frq_text_box = forms.text_box(
parent=self.GetWin(),
value=self.base_frq,
callback=self.set_base_frq,
label="Base frequency",
converter=forms.float_converter(),
)
self.Add(self._base_frq_text_box)
self.wxgui_fftsink2_0 = fftsink2.fft_sink_c(
self.GetWin(),
baseband_freq=0,
y_per_div=10,
y_divs=10,
ref_level=0,
ref_scale=2.0,
sample_rate=samp_rate,
fft_size=1024,
fft_rate=15,
average=False,
avg_alpha=None,
title="FFT Plot",
peak_hold=False,
)
self.Add(self.wxgui_fftsink2_0.win)
self.rtl2832_source_0 = baz.rtl_source_c(defer_creation=True)
self.rtl2832_source_0.set_verbose(True)
self.rtl2832_source_0.set_vid(0x0)
self.rtl2832_source_0.set_pid(0x0)
self.rtl2832_source_0.set_tuner_name("")
self.rtl2832_source_0.set_default_timeout(0)
self.rtl2832_source_0.set_use_buffer(True)
self.rtl2832_source_0.set_fir_coefficients(([]))
if self.rtl2832_source_0.create() == False: raise Exception("Failed to create RTL2832 Source: rtl2832_source_0")
self.rtl2832_source_0.set_bandwidth(300000)
self.rtl2832_source_0.set_sample_rate(samp_rate)
self.rtl2832_source_0.set_frequency(base_frq+frq_offset)
self.rtl2832_source_0.set_gain_mode("sensitive")
self.rtl2832_source_0.set_auto_gain_mode(False)
self.rtl2832_source_0.set_relative_gain(True)
self.rtl2832_source_0.set_gain(30)
self.gr_simple_squelch_cc_0 = gr.simple_squelch_cc(sql_threshold, 0.0001)
self.gr_agc2_xx_0 = gr.agc2_cc(100e-3, 200e-3, 1.0, 1.0, 2.0)
self.blks2_rational_resampler_xxx_0 = blks2.rational_resampler_ccc(
interpolation=48,
decimation=1000,
taps=None,
fractional_bw=None,
)
self.blks2_am_demod_cf_0 = blks2.am_demod_cf(
channel_rate=48000,
audio_decim=1,
audio_pass=5000,
audio_stop=5500,
)
self.audio_sink_0 = audio.sink(48000, "pulse", True)
##################################################
# Connections
##################################################
self.connect((self.rtl2832_source_0, 0), (self.wxgui_fftsink2_0, 0))
self.connect((self.blks2_am_demod_cf_0, 0), (self.audio_sink_0, 0))
self.connect((self.blks2_rational_resampler_xxx_0, 0), (self.gr_simple_squelch_cc_0, 0))
self.connect((self.gr_simple_squelch_cc_0, 0), (self.gr_agc2_xx_0, 0))
self.connect((self.gr_agc2_xx_0, 0), (self.blks2_am_demod_cf_0, 0))
self.connect((self.rtl2832_source_0, 0), (self.blks2_rational_resampler_xxx_0, 0))
def __init__(self, subdev_spec, gain, audio_output):
gr.hier_block2.__init__(self, "receive_path",
gr.io_signature(0, 0, 0), # Input signature
gr.io_signature(0, 0, 0)) # Output signature
self.u = usrp.source_c ()
adc_rate = self.u.adc_rate()
self.if_rate = 256e3 # 256 kS/s
usrp_decim = int(adc_rate // self.if_rate)
if_decim = 4
self.u.set_decim_rate(usrp_decim)
self.quad_rate = self.if_rate // if_decim # 64 kS/s
audio_decim = 2
self.audio_rate = self.quad_rate // audio_decim # 32 kS/s
if subdev_spec is None:
subdev_spec = usrp.pick_rx_subdevice(self.u)
self.subdev = usrp.selected_subdev(self.u, subdev_spec)
print "Using RX d'board %s" % (self.subdev.side_and_name(),)
self.u.set_mux(usrp.determine_rx_mux_value(self.u, subdev_spec))
# Create filter to get actual channel we want
chan_coeffs = gr.firdes.low_pass (1.0, # gain
self.if_rate, # sampling rate
8e3, # low pass cutoff freq
2e3, # width of trans. band
gr.firdes.WIN_HANN) # filter type
print "len(rx_chan_coeffs) =", len(chan_coeffs)
# Decimating Channel filter with frequency translation
# complex in and out, float taps
self.ddc = gr.freq_xlating_fir_filter_ccf(if_decim, # decimation rate
chan_coeffs, # taps
0, # frequency translation amount
self.if_rate) # input sample rate
if USE_SIMPLE_SQUELCH:
self.squelch = gr.simple_squelch_cc(20)
else:
self.squelch = blks2.standard_squelch(self.audio_rate)
# instantiate the guts of the single channel receiver
self.fmrx = blks2.nbfm_rx(self.audio_rate, self.quad_rate)
# audio gain / mute block
self._audio_gain = gr.multiply_const_ff(1.0)
# sound card as final sink
audio_sink = audio.sink (int(self.audio_rate), audio_output)
# now wire it all together
if USE_SIMPLE_SQUELCH:
self.connect (self.u, self.ddc, self.squelch, self.fmrx,
self._audio_gain, audio_sink)
else:
self.connect (self.u, self.ddc, self.fmrx, self.squelch,
self._audio_gain, audio_sink)
if gain is None:
# if no gain was specified, use the mid-point in dB
g = self.subdev.gain_range()
gain = float(g[0]+g[1])/2
self.set_gain(gain)
v = self.volume_range()
self.set_volume((v[0]+v[1])/2)
s = self.squelch_range()
self.set_squelch((s[0]+s[1])/2)