def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.inset.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Inset', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Inset'
)
self.addCustomCodeForTemperatureReading = settings.BooleanSetting(
).getFromValue('Add Custom Code for Temperature Reading', self, True)
self.bridgeWidthMultiplier = settings.FloatSpin().getFromValue(
0.8, 'Bridge Width Multiplier (ratio):', self, 1.2, 1.0)
self.loopOrderChoice = settings.MenuButtonDisplay().getFromName(
'Loop Order Choice:', self)
self.loopOrderAscendingArea = settings.MenuRadio(
).getFromMenuButtonDisplay(self.loopOrderChoice, 'Ascending Area',
self, True)
self.loopOrderDescendingArea = settings.MenuRadio(
).getFromMenuButtonDisplay(self.loopOrderChoice, 'Descending Area',
self, False)
self.overlapRemovalWidthOverPerimeterWidth = settings.FloatSpin(
).getFromValue(0.3,
'Overlap Removal Width over Perimeter Width (ratio):',
self, 0.9, 0.6)
self.turnExtruderHeaterOffAtShutDown = settings.BooleanSetting(
).getFromValue('Turn Extruder Heater Off at Shut Down', self, True)
self.executeTitle = 'Inset'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.multiply.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Multiply', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Multiply'
)
self.activateMultiply = settings.BooleanSetting().getFromValue(
'Activate Multiply:', self, False)
settings.LabelDisplay().getFromName('- Center -', self)
self.centerX = settings.FloatSpin().getFromValue(
-100.0, 'Center X (mm):', self, 100.0, 0.0)
self.centerY = settings.FloatSpin().getFromValue(
-100.0, 'Center Y (mm):', self, 100.0, 0.0)
settings.LabelDisplay().getFromName('- Number of Cells -', self)
self.numberOfColumns = settings.IntSpin().getFromValue(
1, 'Number of Columns (integer):', self, 10, 1)
self.numberOfRows = settings.IntSpin().getFromValue(
1, 'Number of Rows (integer):', self, 10, 1)
self.separationOverPerimeterWidth = settings.FloatSpin().getFromValue(
5.0, 'Separation over Perimeter Width (ratio):', self, 25.0, 15.0)
self.executeTitle = 'Multiply'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.carve.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getTranslatorFileTypeTuples(), 'Open File for Carve',
self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Carve'
)
self.bridgeThicknessMultiplier = settings.FloatSpin().getFromValue(
0.8, 'Bridge Thickness Multiplier (ratio):', self, 1.2, 1.0)
self.extraDecimalPlaces = settings.IntSpin().getFromValue(
0, 'Extra Decimal Places (integer):', self, 2, 1)
self.importCoarseness = settings.FloatSpin().getFromValue(
0.5, 'Import Coarseness (ratio):', self, 2.0, 1.0)
self.infillDirectionBridge = settings.BooleanSetting().getFromValue(
'Infill in Direction of Bridges', self, True)
self.layerThickness = settings.FloatSpin().getFromValue(
0.1, 'Layer Thickness (mm):', self, 1.0, 0.4)
self.layersFrom = settings.IntSpin().getFromValue(
0, 'Layers From (index):', self, 20, 0)
self.layersTo = settings.IntSpin().getSingleIncrementFromValue(
0, 'Layers To (index):', self, 912345678, 912345678)
self.meshTypeLabel = settings.LabelDisplay().getFromName(
'Mesh Type: ', self)
importLatentStringVar = settings.LatentStringVar()
self.correctMesh = settings.Radio().getFromRadio(
importLatentStringVar, 'Correct Mesh', self, True)
self.unprovenMesh = settings.Radio().getFromRadio(
importLatentStringVar, 'Unproven Mesh', self, False)
self.perimeterWidthOverThickness = settings.FloatSpin().getFromValue(
1.4, 'Perimeter Width over Thickness (ratio):', self, 2.2, 1.8)
self.executeTitle = 'Carve'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.cleave.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getTranslatorFileTypeTuples(), 'Open File to be Cleaved',
self, '')
self.extraDecimalPlaces = settings.IntSpin().getFromValue(
0, 'Extra Decimal Places (integer):', self, 2, 1)
self.importCoarseness = settings.FloatSpin().getFromValue(
0.5, 'Import Coarseness (ratio):', self, 2.0, 1.0)
self.layerThickness = settings.FloatSpin().getFromValue(
0.1, 'Layer Thickness (mm):', self, 1.0, 0.4)
self.layersFrom = settings.IntSpin().getFromValue(
0, 'Layers From (index):', self, 20, 0)
self.layersTo = settings.IntSpin().getSingleIncrementFromValue(
0, 'Layers To (index):', self, 912345678, 912345678)
self.meshTypeLabel = settings.LabelDisplay().getFromName(
'Mesh Type: ',
self,
)
importLatentStringVar = settings.LatentStringVar()
self.correctMesh = settings.Radio().getFromRadio(
importLatentStringVar, 'Correct Mesh', self, True)
self.unprovenMesh = settings.Radio().getFromRadio(
importLatentStringVar, 'Unproven Mesh', self, False)
self.perimeterWidth = settings.FloatSpin().getFromValue(
0.4, 'Perimeter Width (mm):', self, 4.0, 2.0)
self.executeTitle = 'Cleave'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.mill.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Mill', self, '')
self.activateMill = settings.BooleanSetting().getFromValue(
'Activate Mill', self, True)
settings.LabelDisplay().getFromName('- Add Loops -', self)
self.addInnerLoops = settings.BooleanSetting().getFromValue(
'Add Inner Loops', self, True)
self.addOuterLoops = settings.BooleanSetting().getFromValue(
'Add Outer Loops', self, True)
self.crossHatch = settings.BooleanSetting().getFromValue(
'Cross Hatch', self, True)
settings.LabelDisplay().getFromName('- Loop Outset -', self)
self.loopInnerOutsetOverPerimeterWidth = settings.FloatSpin(
).getFromValue(0.3, 'Loop Inner Outset over Perimeter Width (ratio):',
self, 0.7, 0.5)
self.loopOuterOutsetOverPerimeterWidth = settings.FloatSpin(
).getFromValue(0.8, 'Loop Outer Outset over Perimeter Width (ratio):',
self, 1.4, 1.0)
self.millWidthOverPerimeterWidth = settings.FloatSpin().getFromValue(
0.8, 'Mill Width over Perimeter Width (ratio):', self, 1.8, 1.0)
self.executeTitle = 'Mill'
def __init__( self ): "Set the default settings, execute title & settings fileName." settings.addListsToRepository( 'skeinforge_tools.craft_plugins.lash.html', '', self ) self.fileNameInput = settings.FileNameInput().getFromFileName( interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Lash', self, '' ) self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute( 'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Lash' ) self.activateLash = settings.BooleanSetting().getFromValue( 'Activate Lash', self, False ) self.xBacklash = settings.FloatSpin().getFromValue( 0.1, 'X Backlash (mm):', self, 0.5, 0.2 ) self.yBacklash = settings.FloatSpin().getFromValue( 0.1, 'Y Backlash (mm):', self, 0.5, 0.3 ) self.executeTitle = 'Lash'
def __init__( self ): "Set the default settings, execute title & settings fileName." profile.addListsToCraftTypeRepository( 'skeinforge_tools.craft_plugins.hop.html', self ) self.fileNameInput = settings.FileNameInput().getFromFileName( interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Hop', self, '' ) self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute( 'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Hop' ) self.activateHop = settings.BooleanSetting().getFromValue( 'Activate Hop', self, False ) self.hopOverLayerThickness = settings.FloatSpin().getFromValue( 0.5, 'Hop Over Layer Thickness (ratio):', self, 1.5, 1.0 ) self.minimumHopAngle = settings.FloatSpin().getFromValue( 20.0, 'Minimum Hop Angle (degrees):', self, 60.0, 30.0 ) self.executeTitle = 'Hop'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.lift.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File to be Lifted', self, '')
self.activateLift = settings.BooleanSetting().getFromValue(
'Activate Lift:', self, True)
self.cuttingLiftOverLayerStep = settings.FloatSpin().getFromValue(
-1.0, 'Cutting Lift over Layer Step (ratio):', self, 1.0, -0.5)
self.clearanceAboveTop = settings.FloatSpin().getFromValue(
0.0, 'Clearance above Top (mm):', self, 10.0, 5.0)
self.executeTitle = 'Lift'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.drill.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Drill', self, '')
self.activateDrill = settings.BooleanSetting().getFromValue(
'Activate Drill', self, True)
self.drillingMarginOnBottom = settings.FloatSpin().getFromValue(
0.0, 'Drilling Margin on Bottom (millimeters):', self, 5.0, 1.0)
self.drillingMarginOnTop = settings.FloatSpin().getFromValue(
0.0, 'Drilling Margin on Top (millimeters):', self, 20.0, 3.0)
self.executeTitle = 'Drill'
def __init__( self ): "Set the default settings, execute title & settings fileName." profile.addListsToCraftTypeRepository( 'skeinforge_tools.craft_plugins.cool.html', self ) self.fileNameInput = settings.FileNameInput().getFromFileName( interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Cool', self, '' ) self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute( 'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Cool' ) self.activateCool = settings.BooleanSetting().getFromValue( 'Activate Cool', self, True ) self.coolType = settings.MenuButtonDisplay().getFromName( 'Cool Type:', self ) self.orbit = settings.MenuRadio().getFromMenuButtonDisplay( self.coolType, 'Orbit', self, False ) self.slowDown = settings.MenuRadio().getFromMenuButtonDisplay( self.coolType, 'Slow Down', self, True ) self.maximumCool = settings.FloatSpin().getFromValue( 0.0, 'Maximum Cool (Celcius):', self, 10.0, 2.0 ) self.minimumLayerTime = settings.FloatSpin().getFromValue( 0.0, 'Minimum Layer Time (seconds):', self, 120.0, 60.0 ) self.minimumOrbitalRadius = settings.FloatSpin().getFromValue( 0.0, 'Minimum Orbital Radius (millimeters):', self, 20.0, 10.0 ) self.turnFanOnAtBeginning = settings.BooleanSetting().getFromValue( 'Turn Fan On at Beginning', self, True ) self.turnFanOffAtEnding = settings.BooleanSetting().getFromValue( 'Turn Fan Off at Ending', self, True ) self.executeTitle = 'Cool'
def __init__( self ): "Set the default settings, execute title & settings fileName." profile.addListsToCraftTypeRepository( 'skeinforge_tools.craft_plugins.whittle.html', self ) self.fileNameInput = settings.FileNameInput().getFromFileName( interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File to be Whittled', self, '' ) self.activateWhittle = settings.BooleanSetting().getFromValue( 'Activate Whittle:', self, False ) self.maximumVerticalStep = settings.FloatSpin().getFromValue( 0.02, 'Maximum Vertical Step (mm):', self, 0.42, 0.1 ) self.executeTitle = 'Whittle'
def __init__(self):
"Set the default settings, execute title & settings fileName."
settings.addListsToRepository(
'skeinforge_tools.craft_plugins.unpause.html', '', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Unpause', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Unpause'
)
self.activateUnpause = settings.BooleanSetting().getFromValue(
'Activate Unpause', self, False)
self.delay = settings.FloatSpin().getFromValue(
2.0, 'Delay (milliseconds):', self, 42.0, 28.0)
self.maximumSpeed = settings.FloatSpin().getFromValue(
1.1, 'Maximum Speed (ratio):', self, 1.9, 1.5)
self.executeTitle = 'Unpause'
def __init__( self ): "Set the default settings, execute title & settings fileName." profile.addListsToCraftTypeRepository( 'skeinforge_tools.craft_plugins.jitter.html', self ) self.fileNameInput = settings.FileNameInput().getFromFileName( interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Jitter', self, '' ) self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute( 'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Jitter' ) self.activateJitter = settings.BooleanSetting().getFromValue( 'Activate Jitter', self, True ) self.jitterOverPerimeterWidth = settings.FloatSpin().getFromValue( 1.0, 'Jitter Over Perimeter Width (ratio):', self, 3.0, 2.0 ) self.executeTitle = 'Jitter'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.chamber.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Chamber', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Chamber'
)
self.activateChamber = settings.BooleanSetting().getFromValue(
'Activate Chamber:', self, True)
self.bedTemperature = settings.FloatSpin().getFromValue(
20.0, 'Bed Temperature (Celcius):', self, 90.0, 60.0)
self.chamberTemperature = settings.FloatSpin().getFromValue(
20.0, 'Chamber Temperature (Celcius):', self, 90.0, 30.0)
self.executeTitle = 'Chamber'
def __init__(self):
"Set the default settings, execute title & settings fileName."
#Set the default settings.
settings.addListsToRepository(
'skeinforge_tools.craft_plugins.export_plugins.binary_16_byte.html',
'', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
[('Gcode text files', '*.gcode')],
'Open File to be Converted to Binary 16 Byte', self, '')
self.feedRateStepLength = settings.FloatSpin().getFromValue(
0.0, 'Feed Rate Step Length (millimeters/second)', self, 1.0, 0.1)
self.fileExtension = settings.StringSetting().getFromValue(
'File Extension:', self, 'bin')
settings.LabelDisplay().getFromName('Offset:', self)
self.xOffset = settings.FloatSpin().getFromValue(
-100.0, 'X Offset (millimeters)', self, 100.0, 0.0)
self.yOffset = settings.FloatSpin().getFromValue(
-100.0, 'Y Offset (millimeters)', self, 100.0, 0.0)
self.zOffset = settings.FloatSpin().getFromValue(
-10.0, 'Z Offset (millimeters)', self, 10.0, 0.0)
settings.LabelDisplay().getFromName('Step Length:', self)
self.xStepLength = settings.FloatSpin().getFromValue(
0.0, 'X Step Length (millimeters)', self, 1.0, 0.1)
self.yStepLength = settings.FloatSpin().getFromValue(
0.0, 'Y Step Length (millimeters)', self, 1.0, 0.1)
self.zStepLength = settings.FloatSpin().getFromValue(
0.0, 'Z Step Length (millimeters)', self, 0.2, 0.01)
#Create the archive, title of the execute button, title of the dialog & settings fileName.
self.executeTitle = 'Convert to Binary 16 Byte'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.comb.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Comb', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Comb'
)
self.activateComb = settings.BooleanSetting().getFromValue(
'Activate Comb', self, True)
self.minimumDepartureDistanceOverPerimeterWidth = settings.FloatSpin(
).getFromValue(
0.0, 'Minimum Departure Distance over Perimeter Width (ratio):',
self, 50.0, 0.0)
self.runningJumpSpaceOverPerimeterWidth = settings.FloatSpin(
).getFromValue(0.0, 'Running Jump Space over Perimeter Width (ratio):',
self, 10.0, 0.0)
self.executeTitle = 'Comb'
def __init__( self ): "Set the default settings, execute title & settings fileName." profile.addListsToCraftTypeRepository( 'skeinforge_tools.craft_plugins.temperature.html', self ) self.fileNameInput = settings.FileNameInput().getFromFileName( interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Temperature', self, '' ) self.activateTemperature = settings.BooleanSetting().getFromValue( 'Activate Temperature:', self, True ) settings.LabelSeparator().getFromRepository( self ) settings.LabelDisplay().getFromName( '- Rate -', self ) self.coolingRate = settings.FloatSpin().getFromValue( 0.0, 'Cooling Rate (Celcius/second):', self, 20.0, 3.0 ) self.heatingRate = settings.FloatSpin().getFromValue( 0.0, 'Heating Rate (Celcius/second):', self, 20.0, 10.0 ) settings.LabelSeparator().getFromRepository( self ) settings.LabelDisplay().getFromName( '- Temperature -', self ) self.chamberTemperature = settings.FloatSpin().getFromValue( 0.0, 'Chamber Temperature (Celcius):', self, 100.0, 25.0 ) self.baseTemperature = settings.FloatSpin().getFromValue( 140.0, 'Base Temperature (Celcius):', self, 260.0, 200.0 ) self.interfaceTemperature = settings.FloatSpin().getFromValue( 140.0, 'Interface Temperature (Celcius):', self, 260.0, 200.0 ) self.objectFirstLayerInfillTemperature = settings.FloatSpin().getFromValue( 140.0, 'Object First Layer Infill Temperature (Celcius):', self, 260.0, 195.0 ) self.objectFirstLayerPerimeterTemperature = settings.FloatSpin().getFromValue( 140.0, 'Object First Layer Perimeter Temperature (Celcius):', self, 260.0, 220.0 ) self.objectNextLayersTemperature = settings.FloatSpin().getFromValue( 140.0, 'Object Next Layers Temperature (Celcius):', self, 260.0, 230.0 ) self.supportLayersTemperature = settings.FloatSpin().getFromValue( 140.0, 'Support Layers Temperature (Celcius):', self, 260.0, 200.0 ) self.supportedLayersTemperature = settings.FloatSpin().getFromValue( 140.0, 'Supported Layers Temperature (Celcius):', self, 260.0, 230.0 ) self.executeTitle = 'Temperature'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.coil.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Coil', self, '')
self.activateCoil = settings.BooleanSetting().getFromValue(
'Activate Coil', self, True)
self.minimumToolDistance = settings.FloatSpin().getFromValue(
10.0, 'Minimum Tool Distance (millimeters):', self, 50.0, 20.0)
self.executeTitle = 'Coil'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.flow.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Flow', self, '')
self.activateFlow = settings.BooleanSetting().getFromValue(
'Activate Flow:', self, True)
self.flowRate = settings.FloatSpin().getFromValue(
50.0, 'Flow Rate (arbitrary units):', self, 250.0, 210.0)
self.executeTitle = 'Flow'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.feed.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Feed', self, '')
self.activateFeed = settings.BooleanSetting().getFromValue(
'Activate Feed:', self, True)
self.feedRatePerSecond = settings.FloatSpin().getFromValue(
2.0, 'Feed Rate (mm/s):', self, 50.0, 16.0)
settings.LabelDisplay().getFromName('Maximum Z Feed Rate:', self)
self.maximumZDrillFeedRatePerSecond = settings.FloatSpin(
).getFromValue(0.02, 'Maximum Z Drill Feed Rate (mm/s):', self, 0.5,
0.1)
self.maximumZTravelFeedRatePerSecond = settings.FloatSpin(
).getFromValue(0.5, 'Maximum Z Travel Feed Rate (mm/s):', self, 10.0,
8.0)
self.travelFeedRatePerSecond = settings.FloatSpin().getFromValue(
2.0, 'Travel Feed Rate (mm/s):', self, 50.0, 16.0)
self.executeTitle = 'Feed'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.stretch.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Stretch', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Stretch'
)
self.activateStretch = settings.BooleanSetting().getFromValue(
'Activate Stretch', self, False)
self.crossLimitDistanceOverPerimeterWidth = settings.FloatSpin(
).getFromValue(3.0,
'Cross Limit Distance Over Perimeter Width (ratio):',
self, 10.0, 5.0)
self.loopStretchOverPerimeterWidth = settings.FloatSpin().getFromValue(
0.05, 'Loop Stretch Over Perimeter Width (ratio):', self, 0.25,
0.11)
self.pathStretchOverPerimeterWidth = settings.FloatSpin().getFromValue(
0.0, 'Path Stretch Over Perimeter Width (ratio):', self, 0.2, 0.0)
settings.LabelDisplay().getFromName('- Perimeter -', self)
self.perimeterInsideStretchOverPerimeterWidth = settings.FloatSpin(
).getFromValue(
0.12, 'Perimeter Inside Stretch Over Perimeter Width (ratio):',
self, 0.52, 0.32)
self.perimeterOutsideStretchOverPerimeterWidth = settings.FloatSpin(
).getFromValue(
0.05, 'Perimeter Outside Stretch Over Perimeter Width (ratio):',
self, 0.25, 0.1)
self.stretchFromDistanceOverPerimeterWidth = settings.FloatSpin(
).getFromValue(1.0,
'Stretch From Distance Over Perimeter Width (ratio):',
self, 3.0, 2.0)
self.executeTitle = 'Stretch'
def __init__( self ): "Set the default settings, execute title & settings fileName." profile.addListsToCraftTypeRepository( 'skeinforge_tools.craft_plugins.speed.html', self ) self.fileNameInput = settings.FileNameInput().getFromFileName( interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Speed', self, '' ) self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute( 'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Speed' ) self.activateSpeed = settings.BooleanSetting().getFromValue( 'Activate Speed:', self, True ) self.addFlowRate = settings.BooleanSetting().getFromValue( 'Add Flow Rate:', self, True ) settings.LabelDisplay().getFromName( '- Bridge -', self ) self.bridgeFeedRateMultiplier = settings.FloatSpin().getFromValue( 0.8, 'Bridge Feed Rate Multiplier (ratio):', self, 1.2, 1.0 ) self.bridgeFlowRateMultiplier = settings.FloatSpin().getFromValue( 0.8, 'Bridge Flow Rate Multiplier (ratio):', self, 1.2, 1.0 ) self.feedRatePerSecond = settings.FloatSpin().getFromValue( 2.0, 'Feed Rate (mm/s):', self, 50.0, 16.0 ) self.flowRateSetting = settings.FloatSpin().getFromValue( 50.0, 'Flow Rate Setting (float):', self, 250.0, 210.0 ) self.maximumZFeedRatePerSecond = settings.FloatSpin().getFromValue( 0.5, 'Maximum Z Feed Rate (mm/s):', self, 10.0, 8.0 ) self.orbitalFeedRateOverOperatingFeedRate = settings.FloatSpin().getFromValue( 0.1, 'Orbital Feed Rate over Operating Feed Rate (ratio):', self, 0.9, 0.5 ) settings.LabelDisplay().getFromName( '- Perimeter -', self ) self.perimeterFeedRateOverOperatingFeedRate = settings.FloatSpin().getFromValue( 0.5, 'Perimeter Feed Rate over Operating Feed Rate (ratio):', self, 1.0, 1.0 ) self.perimeterFlowRateOverOperatingFlowRate = settings.FloatSpin().getFromValue( 0.5, 'Perimeter Flow Rate over Operating Flow Rate (ratio):', self, 1.0, 1.0 ) self.travelFeedRatePerSecond = settings.FloatSpin().getFromValue( 2.0, 'Travel Feed Rate (mm/s):', self, 50.0, 16.0 ) self.executeTitle = 'Speed'
def __init__(self):
"Set the default settings, execute title & settings fileName."
settings.addListsToRepository(
'skeinforge_tools.craft_plugins.fillet.html', '', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File to be Filleted', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Fillet'
)
self.activateFillet = settings.BooleanSetting().getFromValue(
'Activate Fillet', self, False)
self.filletProcedureChoiceLabel = settings.LabelDisplay().getFromName(
'Fillet Procedure Choice: ', self)
filletLatentStringVar = settings.LatentStringVar()
self.arcPoint = settings.Radio().getFromRadio(filletLatentStringVar,
'Arc Point', self, False)
self.arcRadius = settings.Radio().getFromRadio(filletLatentStringVar,
'Arc Radius', self,
False)
self.arcSegment = settings.Radio().getFromRadio(
filletLatentStringVar, 'Arc Segment', self, False)
self.bevel = settings.Radio().getFromRadio(filletLatentStringVar,
'Bevel', self, True)
self.cornerFeedRateOverOperatingFeedRate = settings.FloatSpin(
).getFromValue(0.8,
'Corner Feed Rate over Operating Feed Rate (ratio):',
self, 1.2, 1.0)
self.filletRadiusOverPerimeterWidth = settings.FloatSpin(
).getFromValue(0.25, 'Fillet Radius over Perimeter Width (ratio):',
self, 0.65, 0.35)
self.reversalSlowdownDistanceOverPerimeterWidth = settings.FloatSpin(
).getFromValue(
0.3, 'Reversal Slowdown Distance over Perimeter Width (ratio):',
self, 0.7, 0.5)
self.useIntermediateFeedRateInCorners = settings.BooleanSetting(
).getFromValue('Use Intermediate Feed Rate in Corners', self, True)
self.executeTitle = 'Fillet'
def __init__( self ): "Set the default settings, execute title & settings fileName." profile.addListsToCraftTypeRepository( 'skeinforge_tools.craft_plugins.oozebane.html', self ) self.fileNameInput = settings.FileNameInput().getFromFileName( interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Oozebane', self, '' ) self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute( 'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Oozebane' ) self.activateOozebane = settings.BooleanSetting().getFromValue( 'Activate Oozebane', self, False ) self.afterStartupDistance = settings.FloatSpin().getFromValue( 0.7, 'After Startup Distance (millimeters):', self, 1.7, 1.2 ) self.earlyShutdownDistance = settings.FloatSpin().getFromValue( 0.7, 'Early Shutdown Distance (millimeters):', self, 1.7, 1.2 ) self.earlyStartupDistanceConstant = settings.FloatSpin().getFromValue( 10.0, 'Early Startup Distance Constant (millimeters):', self, 30.0, 20.0 ) self.earlyStartupMaximumDistance = settings.FloatSpin().getFromValue( 0.7, 'Early Startup Maximum Distance (millimeters):', self, 1.7, 1.2 ) self.firstEarlyStartupDistance = settings.FloatSpin().getFromValue( 5.0, 'First Early Startup Distance (millimeters):', self, 45.0, 25.0 ) self.minimumDistanceForEarlyStartup = settings.FloatSpin().getFromValue( 0.0, 'Minimum Distance for Early Startup (millimeters):', self, 10.0, 0.0 ) self.minimumDistanceForEarlyShutdown = settings.FloatSpin().getFromValue( 0.0, 'Minimum Distance for Early Shutdown (millimeters):', self, 10.0, 0.0 ) self.slowdownStartupSteps = settings.IntSpin().getFromValue( 2, 'Slowdown Startup Steps (positive integer):', self, 5, 3 ) self.executeTitle = 'Oozebane'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.clip.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Clip', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Clip'
)
self.activateClip = settings.BooleanSetting().getFromValue(
'Activate Clip', self, True)
self.clipOverExtrusionWidth = settings.FloatSpin().getFromValue(
0.1, 'Clip Over Extrusion Width (ratio):', self, 0.8, 0.5)
self.connectLoops = settings.BooleanSetting().getFromValue(
'Connect Loops', self, True)
self.executeTitle = 'Clip'
def __init__( self ): "Set the default settings, execute title & settings fileName." #Set the default settings. settings.addListsToRepository( 'skeinforge_tools.craft_plugins.export_plugins.gcode_step.html', '', self ) self.addFeedRateEvenWhenUnchanging = settings.BooleanSetting().getFromValue( 'Add Feed Rate Even When Unchanging', self, True ) self.addSpaceBetweenWords = settings.BooleanSetting().getFromValue( 'Add Space Between Words', self, True ) self.addZEvenWhenUnchanging = settings.BooleanSetting().getFromValue( 'Add Z Even When Unchanging', self, True ) self.fileNameInput = settings.FileNameInput().getFromFileName( [ ( 'Gcode text files', '*.gcode' ) ], 'Open File to be Converted to Gcode Step', self, '' ) self.feedRateStepLength = settings.FloatSpin().getFromValue( 0.0, 'Feed Rate Step Length (millimeters/second)', self, 1.0, 0.1 ) settings.LabelDisplay().getFromName( 'Offset:', self ) self.xOffset = settings.FloatSpin().getFromValue( - 100.0, 'X Offset (millimeters)', self, 100.0, 0.0 ) self.yOffset = settings.FloatSpin().getFromValue( -100.0, 'Y Offset (millimeters)', self, 100.0, 0.0 ) self.zOffset = settings.FloatSpin().getFromValue( - 10.0, 'Z Offset (millimeters)', self, 10.0, 0.0 ) self.radiusStepLength = settings.FloatSpin().getFromValue( 0.0, 'Radius Step Length (millimeters)', self, 1.0, 0.1 ) settings.LabelDisplay().getFromName( 'Step Length:', self ) self.xStepLength = settings.FloatSpin().getFromValue( 0.0, 'X Step Length (millimeters)', self, 1.0, 0.1 ) self.yStepLength = settings.FloatSpin().getFromValue( 0.0, 'Y Step Length (millimeters)', self, 1.0, 0.1 ) self.zStepLength = settings.FloatSpin().getFromValue( 0.0, 'Z Step Length (millimeters)', self, 0.2, 0.01 ) #Create the archive, title of the execute button, title of the dialog & settings fileName. self.executeTitle = 'Convert to Gcode Step'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.wipe.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Wipe', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Wipe'
)
self.activateWipe = settings.BooleanSetting().getFromValue(
'Activate Wipe', self, False)
settings.LabelDisplay().getFromName('- Location Arrival -', self)
self.locationArrivalX = settings.FloatSpin().getFromValue(
-100.0, 'Location Arrival X (mm):', self, 100.0, -70.0)
self.locationArrivalY = settings.FloatSpin().getFromValue(
-100.0, 'Location Arrival Y (mm):', self, 100.0, -50.0)
self.locationArrivalZ = settings.FloatSpin().getFromValue(
-100.0, 'Location Arrival Z (mm):', self, 100.0, 50.0)
settings.LabelDisplay().getFromName('- Location Departure -', self)
self.locationDepartureX = settings.FloatSpin().getFromValue(
-100.0, 'Location Departure X (mm):', self, 100.0, -70.0)
self.locationDepartureY = settings.FloatSpin().getFromValue(
-100.0, 'Location Departure Y (mm):', self, 100.0, -40.0)
self.locationDepartureZ = settings.FloatSpin().getFromValue(
-100.0, 'Location Departure Z (mm):', self, 100.0, 50.0)
settings.LabelDisplay().getFromName('- Location Wipe -', self)
self.locationWipeX = settings.FloatSpin().getFromValue(
-100.0, 'Location Wipe X (mm):', self, 100.0, -70.0)
self.locationWipeY = settings.FloatSpin().getFromValue(
-100.0, 'Location Wipe Y (mm):', self, 100.0, -70.0)
self.locationWipeZ = settings.FloatSpin().getFromValue(
-100.0, 'Location Wipe Z (mm):', self, 100.0, 50.0)
self.wipePeriod = settings.IntSpin().getFromValue(
1, 'Wipe Period (layers):', self, 5, 3)
self.executeTitle = 'Wipe'
def __init__( self ): "Set the default settings, execute title & settings fileName." profile.addListsToCraftTypeRepository( 'skeinforge_tools.craft_plugins.splodge.html', self ) self.fileNameInput = settings.FileNameInput().getFromFileName( interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Splodge', self, '' ) self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute( 'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Splodge' ) self.activateSplodge = settings.BooleanSetting().getFromValue( 'Activate Splodge', self, False ) settings.LabelDisplay().getFromName( '- Initial -', self ) self.initialLiftOverExtraThickness = settings.FloatSpin().getFromValue( 0.5, 'Initial Lift over Extra Thickness (ratio):', self, 1.5, 1.0 ) self.initialSplodgeFeedRate = settings.FloatSpin().getFromValue( 0.4, 'Initial Splodge Feed Rate (mm/s):', self, 2.4, 1.0 ) self.initialSplodgeQuantityLength = settings.FloatSpin().getFromValue( 10.0, 'Initial Splodge Quantity Length (millimeters):', self, 90.0, 30.0 ) settings.LabelDisplay().getFromName( '- Operating -', self ) self.operatingLiftOverExtraThickness = settings.FloatSpin().getFromValue( 0.5, 'Operating Lift over Extra Thickness (ratio):', self, 1.5, 1.0 ) self.operatingSplodgeFeedRate = settings.FloatSpin().getFromValue( 0.4, 'Operating Splodge Feed Rate (mm/s):', self, 2.4, 1.0 ) self.operatingSplodgeQuantityLength = settings.FloatSpin().getFromValue( 0.4, 'Operating Splodge Quantity Length (millimeters):', self, 2.4, 1.0 ) self.executeTitle = 'Splodge'
def __init__(self):
"Set the default settings, execute title & settings fileName."
settings.addListsToRepository(
'skeinforge_tools.analyze_plugins.statistic.html', '', self)
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Statistic'
)
self.activateStatistic = settings.BooleanSetting().getFromValue(
'Activate Statistic', self, True)
self.extrusionDiameterOverThickness = settings.FloatSpin(
).getFromValue(1.0, 'Extrusion Diameter over Thickness (ratio):', self,
1.5, 1.25)
self.fileNameInput = settings.FileNameInput().getFromFileName(
[('Gcode text files', '*.gcode')],
'Open File to Generate Statistics for', self, '')
self.printStatistics = settings.BooleanSetting().getFromValue(
'Print Statistics', self, True)
self.saveStatistics = settings.BooleanSetting().getFromValue(
'Save Statistics', self, False)
#Create the archive, title of the execute button, title of the dialog & settings fileName.
self.executeTitle = 'Generate Statistics'
def __init__(self):
"Set the default settings, execute title & settings fileName."
profile.addListsToCraftTypeRepository(
'skeinforge_tools.craft_plugins.tower.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Tower', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Tower'
)
self.activateTower = settings.BooleanSetting().getFromValue(
'Activate Tower', self, False)
self.extruderPossibleCollisionConeAngle = settings.FloatSpin(
).getFromValue(40.0,
'Extruder Possible Collision Cone Angle (degrees):',
self, 80.0, 60.0)
self.maximumTowerHeight = settings.IntSpin().getFromValue(
2, 'Maximum Tower Height (layers):', self, 10, 5)
self.towerStartLayer = settings.IntSpin().getFromValue(
1, 'Tower Start Layer (integer):', self, 5, 1)
self.executeTitle = 'Tower'
