# Check for any errors with initializing commands
log_all_events(tcp_socket)
# turn on Channel 1
tcp_socket.send_scpi_command('OUTP1 1')
# wait until the channel is fully ramped
read_until_event(tcp_socket, 100) # event 100 is "Channel Ready"
# check for all events and measure readings on Channel 1 once per second for 10 seconds,
# it is best practice to do this to ensure Channel 1 is on and does not have any errors
time_end = time.time() + 10
while time.time() < time_end:
log_all_events(tcp_socket)
log_memory_table_read(tcp_socket)
wait(1)
# set Channel 1's current to 200 mA while running
tcp_socket.send_scpi_command('SOUR1:CURR 0.2')
# set Channel 1's Pulse On Time to 100µs dynamically while channel is operating. Check events and measure readings
tcp_socket.send_scpi_command('SOUR1:PULS:TON 0.0001')
log_all_events(tcp_socket)
log_memory_table_read(tcp_socket)
wait(1)
# set Channel 1's Pulse Off Time to 100µs dynamically while channel is operating. Check events and measure readings
tcp_socket.send_scpi_command('SOUR1:PULS:TOFF 0.0001')
# after dynamically applying all new settings, check for all events and measure readings on Channel 1 once per second for 5 seconds
time_end = time.time() + 5
# turn on Channel 1
tcp_socket.send_scpi_command('OUTP1 1')
# Wait until channel is ready for a trigger command
read_until_event(tcp_socket, 100) # event 100 is "Channel Ready"
# Output 1ms pulse for Channel 1
tcp_socket.send_scpi_command('OUTP1:TRIG')
# check for all events and measure readings on the channel once per second for 2 seconds,
# it is best practice to do this to ensure the channel is on and does not have any errors
time_end = time.time() + 2
while time.time() < time_end:
log_all_events(tcp_socket)
log_memory_table_read(tcp_socket)
wait(1)
# check that the Multi Pulse output has ended
hasMultiPulseEndedString = ''
while hasMultiPulseEndedString != 'TRUE':
tcp_socket.send_scpi_command('SOUR1:PULS:END?')
hasMultiPulseEndedString = tcp_socket.read_data()
wait(0.5)
# set the Force Sense Selector Switch state to Auxiliary to disconnect the SpikeSafe output from the DUT
# this action can be performed as long as no pulses are actively being outputted from the SpikeSafe. The channel may be enabled
tcp_socket.send_scpi_command('OUTP1:CONN AUX')
# Show a message box so any tasks using the Auxiliary source may be performed before adjusting the switch back to Primary
# The SpikeSafe is not electrically connected to the DUT at this time
messagebox.showinfo(
# turn on Channel 1
tcp_socket.send_scpi_command('OUTP1 1')
# wait until Channel 1 is ready to pulse
read_until_event(tcp_socket, 100) # event 100 is "Channel Ready"
log_and_print_to_console(
'\nMeasurement Current is currently outputting to the DUT.\n\nPress \'Enter\' in the console once temperature has been stabilized at T1, then record V1 and T1.'
)
input()
log_and_print_to_console('Enter T1 (in °C):')
temperature_one = float(receive_user_input_and_log())
log_and_print_to_console('Enter V1 (in V):')
voltage_one = float(receive_user_input_and_log())
wait(2)
log_and_print_to_console(
'\nMeasurement Current is currently outputting to the DUT.\n\nChange the control temperature to T2.\n\nPress \'Enter\' in the console once temperature has been stabilized at T2, then record V2 and T2.'
)
input()
log_and_print_to_console('Enter T2 (in °C):')
temperature_two = float(receive_user_input_and_log())
log_and_print_to_console('Enter V2 (in °C):')
voltage_two = float(receive_user_input_and_log())
k_factor = (voltage_two - voltage_one) / (temperature_two -
temperature_one)
log_and_print_to_console('K-factor: {} V/°C'.format(k_factor))
# turn off Channel 1
# turn on Channel 1
tcp_socket.send_scpi_command('OUTP1 1')
# wait until Channel 1 is ready to pulse
read_until_event(tcp_socket, 100) # event 100 is "Channel Ready"
# output the Digitizer hardware output trigger. 10µs after this signal is outputted, the Multi Pulse sequence will start
tcp_socket.send_scpi_command('VOLT:OUTP:TRIG')
# check that the Multi Pulse output has ended
has_multi_pulse_ended = ''
while has_multi_pulse_ended != 'TRUE':
tcp_socket.send_scpi_command('SOUR1:PULS:END?')
has_multi_pulse_ended = tcp_socket.read_data()
wait(0.5)
# output the Digitizer hardware output trigger. As long as the SpikeSafe is ready to pulse, this can be done continuously
tcp_socket.send_scpi_command('VOLT:OUTP:TRIG')
# check that the Multi Pulse output has ended
has_multi_pulse_ended = ''
while has_multi_pulse_ended != 'TRUE':
tcp_socket.send_scpi_command('SOUR1:PULS:END?')
has_multi_pulse_ended = tcp_socket.read_data()
wait(0.5)
# wait for the Digitizer measurements to complete
wait_for_new_voltage_data(tcp_socket, 0.5)
# fetch the Digitizer voltage readings using VOLT:FETC? query
# Check for any errors with initializing commands
log_all_events(tcp_socket)
# turn on Channel 1
tcp_socket.send_scpi_command('OUTP1 1')
# wait until the channel is fully ramped
read_until_event(tcp_socket, 100) # event 100 is "Channel Ready"
# check for all events and measure readings on Channel 1 once per second for 5 seconds,
# it is best practice to do this to ensure Channel 1 is on and does not have any errors
time_end = time.time() + 5
while time.time() < time_end:
log_all_events(tcp_socket)
log_memory_table_read(tcp_socket)
wait(1)
# set Channel 1's Pulse Hold to Period. Setting any pulse-related setting will not re-calculate Pulse Period
tcp_socket.send_scpi_command('SOUR1:PULS:HOLD PER')
log_and_print('Held Pulse Period')
# set Channel 1's Pulse Width to 8ms. Since Period is being held, the Period will remain at 10ms
pulse_width_seconds = 0.008
tcp_socket.send_scpi_command(
'SOUR1:PULS:WIDT {}'.format(pulse_width_seconds))
log_and_print('Set Pulse Width to {}s'.format(pulse_width_seconds))
# verify that the expected updates are made to the pulse settings
verify_current_pulse_settings(tcp_socket)
# wait two seconds while running with the newly updated settings