def __init__(self, constellation, differential, rotation):
if constellation.arity() > 256:
# If this becomes limiting some of the blocks should be generalised so
# that they can work with shorts and ints as well as chars.
raise ValueError("Constellation cannot contain more than 256 points.")
gr.hier_block2.__init__(self, "mod_demod",
gr.io_signature(1, 1, gr.sizeof_char), # Input signature
gr.io_signature(1, 1, gr.sizeof_char)) # Output signature
arity = constellation.arity()
# TX
self.constellation = constellation
self.differential = differential
import weakref
self.blocks = [weakref.proxy(self)]
# We expect a stream of unpacked bits.
# First step is to pack them.
self.blocks.append(
gr.unpacked_to_packed_bb(1, gr.GR_MSB_FIRST))
# Second step we unpack them such that we have k bits in each byte where
# each constellation symbol hold k bits.
self.blocks.append(
gr.packed_to_unpacked_bb(self.constellation.bits_per_symbol(),
gr.GR_MSB_FIRST))
# Apply any pre-differential coding
# Gray-coding is done here if we're also using differential coding.
if self.constellation.apply_pre_diff_code():
self.blocks.append(gr.map_bb(self.constellation.pre_diff_code()))
# Differential encoding.
if self.differential:
self.blocks.append(gr.diff_encoder_bb(arity))
# Convert to constellation symbols.
self.blocks.append(gr.chunks_to_symbols_bc(self.constellation.points(),
self.constellation.dimensionality()))
# CHANNEL
# Channel just consists of a rotation to check differential coding.
if rotation is not None:
self.blocks.append(gr.multiply_const_cc(rotation))
# RX
# Convert the constellation symbols back to binary values.
self.blocks.append(digital_swig.constellation_decoder_cb(self.constellation.base()))
# Differential decoding.
if self.differential:
self.blocks.append(gr.diff_decoder_bb(arity))
# Decode any pre-differential coding.
if self.constellation.apply_pre_diff_code():
self.blocks.append(gr.map_bb(
mod_codes.invert_code(self.constellation.pre_diff_code())))
# unpack the k bit vector into a stream of bits
self.blocks.append(gr.unpack_k_bits_bb(
self.constellation.bits_per_symbol()))
# connect to block output
check_index = len(self.blocks)
self.blocks = self.blocks[:check_index]
self.blocks.append(weakref.proxy(self))
self.connect(*self.blocks)
def __init__(self, constellation, differential, rotation):
if constellation.arity() > 256:
# If this becomes limiting some of the blocks should be generalised so
# that they can work with shorts and ints as well as chars.
raise ValueError("Constellation cannot contain more than 256 points.")
gr.hier_block2.__init__(self, "mod_demod",
gr.io_signature(1, 1, gr.sizeof_char), # Input signature
gr.io_signature(1, 1, gr.sizeof_char)) # Output signature
arity = constellation.arity()
# TX
self.constellation = constellation
self.differential = differential
self.blocks = [self]
# We expect a stream of unpacked bits.
# First step is to pack them.
self.blocks.append(
gr.unpacked_to_packed_bb(1, gr.GR_MSB_FIRST))
# Second step we unpack them such that we have k bits in each byte where
# each constellation symbol hold k bits.
self.blocks.append(
gr.packed_to_unpacked_bb(self.constellation.bits_per_symbol(),
gr.GR_MSB_FIRST))
# Apply any pre-differential coding
# Gray-coding is done here if we're also using differential coding.
if self.constellation.apply_pre_diff_code():
self.blocks.append(gr.map_bb(self.constellation.pre_diff_code()))
# Differential encoding.
if self.differential:
self.blocks.append(gr.diff_encoder_bb(arity))
# Convert to constellation symbols.
self.blocks.append(gr.chunks_to_symbols_bc(self.constellation.points(),
self.constellation.dimensionality()))
# CHANNEL
# Channel just consists of a rotation to check differential coding.
if rotation is not None:
self.blocks.append(gr.multiply_const_cc(rotation))
# RX
# Convert the constellation symbols back to binary values.
self.blocks.append(digital_swig.constellation_decoder_cb(self.constellation.base()))
# Differential decoding.
if self.differential:
self.blocks.append(gr.diff_decoder_bb(arity))
# Decode any pre-differential coding.
if self.constellation.apply_pre_diff_code():
self.blocks.append(gr.map_bb(
mod_codes.invert_code(self.constellation.pre_diff_code())))
# unpack the k bit vector into a stream of bits
self.blocks.append(gr.unpack_k_bits_bb(
self.constellation.bits_per_symbol()))
# connect to block output
check_index = len(self.blocks)
self.blocks = self.blocks[:check_index]
self.blocks.append(self)
self.connect(*self.blocks)
def __init__(self, options, args):
gr.top_block.__init__(self)
self.options = options
self.args = args
frekvens = options.freq
# u = usrp.source_c(0)
# u.set_decim_rate(256)
# subdev_spec = (1,0)
# u.set_mux(usrp.determine_rx_mux_value(u,subdev_spec))
# subdev = usrp.selected_subdev(u,subdev_spec)
# subdev.set_auto_tr(True)
# subdev.set_gain(57)
# usrp.tune(u,0,subdev,frekvens)#106.3e6)
# samplerate = 64000000/256 # 250000
self.u = uhd.usrp_source("", uhd.io_type_t.COMPLEX_FLOAT32, 1)
self.u.set_subdev_spec("")
# default should be good?
self.u.set_samp_rate(250e3)
samplerate = self.u.get_samp_rate() # Retrieve what it actually does
self.u.set_antenna("RX2", 0)
if options.gain is None: # set to halfway
g = self.u.get_gain_range()
options.gain = (g.start() + g.stop()) / 2.0
if not (self.u.set_center_freq(frekvens, 0)):
print "Failed to set frequency"
sys.exit(1)
print "Setting gain to %i" % options.gain
self.u.set_gain(options.gain)
coeffs = gr.firdes.low_pass(1, samplerate, 10000, 10000)
filter = gr.fir_filter_ccf(5, coeffs)
gang = gr.multiply_const_ff(10)
lpcoeffs = gr.firdes.low_pass(1, samplerate, 8000, 3000)
lpfilter = gr.fir_filter_fff(1, lpcoeffs)
demod = gr.quadrature_demod_cf(0.5)
clockrec = gr.clock_recovery_mm_ff(
float(samplerate) / 5 / 9600, 0.25 * 0.175 * 0.175, 0.5, 0.175,
0.005)
#datadec = ais.ais_decoder_mysql("localhost","diverse","aisblock","elgelg")
self.datadec = ais.ais_decoder_gearth(30003)
slicer = gr.binary_slicer_fb()
diff = gr.diff_decoder_bb(2)
invert = ais.invert10_bb()
# print subdev.name()
self.connect(self.u, filter, demod, lpfilter, gang, clockrec, slicer,
diff, invert, self.datadec)
def __init__(self, options, args):
gr.top_block.__init__(self)
self.options = options
self.args = args
frekvens = options.freq
# u = usrp.source_c(0)
# u.set_decim_rate(256)
# subdev_spec = (1,0)
# u.set_mux(usrp.determine_rx_mux_value(u,subdev_spec))
# subdev = usrp.selected_subdev(u,subdev_spec)
# subdev.set_auto_tr(True)
# subdev.set_gain(57)
# usrp.tune(u,0,subdev,frekvens)#106.3e6)
# samplerate = 64000000/256 # 250000
self.u = uhd.usrp_source("", uhd.io_type_t.COMPLEX_FLOAT32,1)
self.u.set_subdev_spec(""); # default should be good?
self.u.set_samp_rate(250e3);
samplerate = self.u.get_samp_rate() # Retrieve what it actually does
self.u.set_antenna("RX2",0)
if options.gain is None: # set to halfway
g = self.u.get_gain_range()
options.gain = (g.start()+g.stop()) / 2.0
if not(self.u.set_center_freq(frekvens, 0)):
print "Failed to set frequency"
sys.exit(1)
print "Setting gain to %i" % options.gain
self.u.set_gain(options.gain)
coeffs = gr.firdes.low_pass(1,samplerate,10000,10000)
filter = gr.fir_filter_ccf(5,coeffs)
gang = gr.multiply_const_ff(10)
lpcoeffs = gr.firdes.low_pass(1,samplerate,8000,3000)
lpfilter = gr.fir_filter_fff(1,lpcoeffs)
demod = gr.quadrature_demod_cf(0.5)
clockrec = gr.clock_recovery_mm_ff(float(samplerate)/5/9600,0.25*0.175*0.175,0.5,0.175,0.005)
#datadec = ais.ais_decoder_mysql("localhost","diverse","aisblock","elgelg")
self.datadec = ais.ais_decoder_gearth(30003)
slicer = gr.binary_slicer_fb()
diff = gr.diff_decoder_bb(2)
invert = ais.invert10_bb()
# print subdev.name()
self.connect(self.u,filter,demod,lpfilter,gang,clockrec,
slicer,diff,invert,self.datadec)
def test_diff_encdec_002(self):
random.seed(0)
modulus = 8
src_data = make_random_int_tuple(40000, 0, modulus-1)
expected_result = src_data
src = gr.vector_source_b(src_data)
enc = gr.diff_encoder_bb(modulus)
dec = gr.diff_decoder_bb(modulus)
dst = gr.vector_sink_b()
self.tb.connect(src, enc, dec, dst)
self.tb.run() # run the graph and wait for it to finish
actual_result = dst.data() # fetch the contents of the sink
self.assertEqual(expected_result, actual_result)
def __init__(self, samp_rate, symbol_rate=31.25):
super(psk31_receiver, self).__init__(
"psk31_receiver",
gr.io_signature(1, 1, gr.sizeof_gr_complex),
gr.io_signature(0, 0, 1))
self.symbol_rate = symbol_rate
self.costas = digital.costas_loop_cc(2*3.14/100, 4)
self.clock_recovery = digital.clock_recovery_mm_cc(
1.0*samp_rate/symbol_rate, 0.25 * 0.1*0.1, 0.05, 0.1, 0.001)
self.receiver = digital.constellation_receiver_cb(
digital.constellation_bpsk().base(), 2*3.14/100, -0.25, 0.25)
self.diff = gr.diff_decoder_bb(2)
self.decoder = ham.psk31_decode_bb(True)
self.msgq_out = gr.msg_queue()
self.snk = gr.message_sink(gr.sizeof_char, self.msgq_out, True)
self.connect(self, self.costas, self.clock_recovery,
self.receiver, self.diff, self.decoder, self.snk)
def __init__(self, samples_per_symbol=1):
gr.hier_block2.__init__(self, 'gsm_modulate_burst',
gr.io_signature2(2, 2, 58 * 2, 1),
gr.io_signature(1, 1, gr.sizeof_gr_complex))
# take care of the packetizer
conf = mlse.make_packet_config_gsm()
self.packetbuilder = mlse.packetbuilder_midamble_vbb(conf)
self.connect(self, self.packetbuilder)
self.connect((self, 1), (self.packetbuilder, 1)) # tsc_index
# append 8 1-bits to the packet for the idle-time between bursts.
# This is necessary among others to flush the gmsk-modulator which is causal.
# (We use 1-bits because that's what the gsm-standard says)
# (we also only use 8 bits, because the specified value of 8.25 only works
# properly with samplerates that are a multiple of 4.)
self.guardbits = gr.vector_source_b((1, ) * 8, True, 8)
self.guard_cat = mlse.vector_concat_vv(148, 8)
self.connect(self.packetbuilder, self.guard_cat)
self.connect(self.guardbits, (self.guard_cat, 1))
# we now have a vector of bits, transform that into a stream
self.tostream = gr.vector_to_stream(1, 148 + 8)
# do the precoding:
self.diffcode = gr.diff_decoder_bb(2)
self.nrz = gr.map_bb([1, -1])
self.connect(self.guard_cat, self.tostream, self.diffcode, self.nrz)
# modulate
self.mod = digital.gmskmod_bc(samples_per_symbol, 0.3, 8)
# skip the first gmsk_length*samplerate/2 samples to make this block
# acausal.
# self.skiphead = gr.skiphead(gr.sizeof_gr_complex, int(samples_per_symbol*4.5));
# self.connect(self.nrz, self.mod, self.skiphead, self)
self.connect(self.nrz, self.mod,
self) # workaround: we need a negative delay later,
def __init__(self, samples_per_symbol = 1):
gr.hier_block2.__init__(self, 'gsm_modulate_burst',
gr.io_signature2(2,2,58*2,1),
gr.io_signature(1, 1, gr.sizeof_gr_complex))
# take care of the packetizer
conf = mlse.make_packet_config_gsm()
self.packetbuilder = mlse.packetbuilder_midamble_vbb(conf)
self.connect(self, self.packetbuilder)
self.connect((self,1), (self.packetbuilder,1)) # tsc_index
# append 8 1-bits to the packet for the idle-time between bursts.
# This is necessary among others to flush the gmsk-modulator which is causal.
# (We use 1-bits because that's what the gsm-standard says)
# (we also only use 8 bits, because the specified value of 8.25 only works
# properly with samplerates that are a multiple of 4.)
self.guardbits = gr.vector_source_b((1,)*8,True,8)
self.guard_cat = mlse.vector_concat_vv(148,8)
self.connect(self.packetbuilder, self.guard_cat)
self.connect(self.guardbits, (self.guard_cat,1))
# we now have a vector of bits, transform that into a stream
self.tostream = gr.vector_to_stream(1, 148+8)
# do the precoding:
self.diffcode = gr.diff_decoder_bb(2);
self.nrz = gr.map_bb([1,-1])
self.connect(self.guard_cat, self.tostream, self.diffcode, self.nrz)
# modulate
self.mod = digital.gmskmod_bc(samples_per_symbol, 0.3, 8)
# skip the first gmsk_length*samplerate/2 samples to make this block
# acausal.
# self.skiphead = gr.skiphead(gr.sizeof_gr_complex, int(samples_per_symbol*4.5));
# self.connect(self.nrz, self.mod, self.skiphead, self)
self.connect(self.nrz, self.mod, self) # workaround: we need a negative delay later,
def __init__(self, frame, panel, vbox, argv):
stdgui2.std_top_block.__init__(self, frame, panel, vbox, argv)
parser = OptionParser(option_class=eng_option)
parser.add_option("-V",
"--volume",
type="eng_float",
default=None,
help="set volume (default is midpoint)")
parser.add_option("-O",
"--audio-output",
type="string",
default="plughw:0,0",
help="pcm device name (default is plughw:0,0)")
# print help when called with wrong arguments
(options, args) = parser.parse_args()
if len(args) != 0:
parser.print_help()
sys.exit(1)
self.file_source = gr.file_source(gr.sizeof_gr_complex * 1,
offline_samples, True)
chan_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
usrp_rate, # sampling rate
80e3, # passband cutoff
35e3, # transition width
gr.firdes.WIN_HAMMING)
self.chan_filter = gr.fir_filter_ccf(1, chan_filter_coeffs)
print "# channel filter:", len(chan_filter_coeffs), "taps"
# PLL-based WFM demod
fm_alpha = 0.25 * 250e3 * math.pi / usrp_rate # 0.767
fm_beta = fm_alpha * fm_alpha / 4.0 # 0.147
fm_max_freq = 2.0 * math.pi * 90e3 / usrp_rate # 2.209
self.fm_demod = gr.pll_freqdet_cf(
fm_alpha, # phase gain
fm_beta, # freq gain
fm_max_freq, # in radians/sample
-fm_max_freq)
self.connect(self.file_source, self.chan_filter, self.fm_demod)
# L+R, pilot, L-R, RDS filters
lpr_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
usrp_rate, # sampling rate
15e3, # passband cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.lpr_filter = gr.fir_filter_fff(audio_decim, lpr_filter_coeffs)
pilot_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
usrp_rate, # sampling rate
19e3 - 500, # low cutoff
19e3 + 500, # high cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.pilot_filter = gr.fir_filter_fff(1, pilot_filter_coeffs)
dsbsc_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
usrp_rate, # sampling rate
38e3 - 15e3 / 2, # low cutoff
38e3 + 15e3 / 2, # high cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.dsbsc_filter = gr.fir_filter_fff(1, dsbsc_filter_coeffs)
rds_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
usrp_rate, # sampling rate
57e3 - 3e3, # low cutoff
57e3 + 3e3, # high cutoff
3e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_filter = gr.fir_filter_fff(1, rds_filter_coeffs)
print "# lpr filter:", len(lpr_filter_coeffs), "taps"
print "# pilot filter:", len(pilot_filter_coeffs), "taps"
print "# dsbsc filter:", len(dsbsc_filter_coeffs), "taps"
print "# rds filter:", len(rds_filter_coeffs), "taps"
self.connect(self.fm_demod, self.lpr_filter)
self.connect(self.fm_demod, self.pilot_filter)
self.connect(self.fm_demod, self.dsbsc_filter)
self.connect(self.fm_demod, self.rds_filter)
# down-convert L-R, RDS
self.stereo_baseband = gr.multiply_ff()
self.connect(self.pilot_filter, (self.stereo_baseband, 0))
self.connect(self.pilot_filter, (self.stereo_baseband, 1))
self.connect(self.dsbsc_filter, (self.stereo_baseband, 2))
self.rds_baseband = gr.multiply_ff()
self.connect(self.pilot_filter, (self.rds_baseband, 0))
self.connect(self.pilot_filter, (self.rds_baseband, 1))
self.connect(self.pilot_filter, (self.rds_baseband, 2))
self.connect(self.rds_filter, (self.rds_baseband, 3))
# low-pass and downsample L-R
lmr_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
usrp_rate, # sampling rate
15e3, # passband cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.lmr_filter = gr.fir_filter_fff(audio_decim, lmr_filter_coeffs)
self.connect(self.stereo_baseband, self.lmr_filter)
# create L, R from L-R, L+R
self.left = gr.add_ff()
self.right = gr.sub_ff()
self.connect(self.lpr_filter, (self.left, 0))
self.connect(self.lmr_filter, (self.left, 1))
self.connect(self.lpr_filter, (self.right, 0))
self.connect(self.lmr_filter, (self.right, 1))
# send audio to null sink
self.null0 = gr.null_sink(gr.sizeof_float)
self.null1 = gr.null_sink(gr.sizeof_float)
self.connect(self.left, self.null0)
self.connect(self.right, self.null1)
# low-pass the baseband RDS signal at 1.5kHz
rds_bb_filter_coeffs = gr.firdes.low_pass(
1, # gain
usrp_rate, # sampling rate
1.5e3, # passband cutoff
2e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_bb_filter = gr.fir_filter_fff(audio_decim,
rds_bb_filter_coeffs)
print "# rds bb filter:", len(rds_bb_filter_coeffs), "taps"
self.connect(self.rds_baseband, self.rds_bb_filter)
# 1187.5bps = 19kHz/16
self.clock_divider = rds.freq_divider(16)
rds_clock_taps = gr.firdes.low_pass(
1, # gain
usrp_rate, # sampling rate
1.2e3, # passband cutoff
1.5e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_clock = gr.fir_filter_fff(audio_decim, rds_clock_taps)
print "# rds clock filter:", len(rds_clock_taps), "taps"
self.connect(self.pilot_filter, self.clock_divider, self.rds_clock)
# bpsk_demod, diff_decoder, rds_decoder
self.bpsk_demod = rds.bpsk_demod(audio_rate)
self.differential_decoder = gr.diff_decoder_bb(2)
self.msgq = gr.msg_queue()
self.rds_decoder = rds.data_decoder(self.msgq)
self.connect(self.rds_bb_filter, (self.bpsk_demod, 0))
self.connect(self.rds_clock, (self.bpsk_demod, 1))
self.connect(self.bpsk_demod, self.differential_decoder)
self.connect(self.differential_decoder, self.rds_decoder)
self.frame = frame
self.panel = panel
self._build_gui(vbox, usrp_rate, audio_rate)
def __init__(self, constellation,
samples_per_symbol=_def_samples_per_symbol,
differential=_def_differential,
excess_bw=_def_excess_bw,
gray_coded=True,
freq_bw=_def_freq_bw,
timing_bw=_def_timing_bw,
phase_bw=_def_phase_bw,
verbose=_def_verbose,
log=_def_log):
"""
Hierarchical block for RRC-filtered differential generic demodulation.
The input is the complex modulated signal at baseband.
The output is a stream of bits packed 1 bit per byte (LSB)
@param constellation: determines the modulation type
@type constellation: gnuradio.digital.gr_constellation
@param samples_per_symbol: samples per symbol >= 2
@type samples_per_symbol: float
@param excess_bw: Root-raised cosine filter excess bandwidth
@type excess_bw: float
@param gray_coded: turn gray coding on/off
@type gray_coded: bool
@param freq_bw: loop filter lock-in bandwidth
@type freq_bw: float
@param timing_bw: timing recovery loop lock-in bandwidth
@type timing_bw: float
@param phase_bw: phase recovery loop bandwidth
@type phase_bw: float
@param verbose: Print information about modulator?
@type verbose: bool
@param debug: Print modualtion data to files?
@type debug: bool
"""
gr.hier_block2.__init__(self, "generic_demod",
gr.io_signature(1, 1, gr.sizeof_gr_complex), # Input signature
gr.io_signature(1, 1, gr.sizeof_char)) # Output signature
self._constellation = constellation.base()
self._samples_per_symbol = samples_per_symbol
self._excess_bw = excess_bw
self._phase_bw = phase_bw
self._freq_bw = freq_bw
self._timing_bw = timing_bw
self._timing_max_dev= _def_timing_max_dev
self._differential = differential
if self._samples_per_symbol < 2:
raise TypeError, ("sbp must be >= 2, is %d" % self._samples_per_symbol)
arity = pow(2,self.bits_per_symbol())
nfilts = 32
ntaps = 11 * int(self._samples_per_symbol*nfilts)
# Automatic gain control
self.agc = gr.agc2_cc(0.6e-1, 1e-3, 1, 1, 100)
# Frequency correction
fll_ntaps = 55
self.freq_recov = digital_swig.fll_band_edge_cc(self._samples_per_symbol, self._excess_bw,
fll_ntaps, self._freq_bw)
# symbol timing recovery with RRC data filter
taps = gr.firdes.root_raised_cosine(nfilts, nfilts*self._samples_per_symbol,
1.0, self._excess_bw, ntaps)
self.time_recov = gr.pfb_clock_sync_ccf(self._samples_per_symbol,
self._timing_bw, taps,
nfilts, nfilts//2, self._timing_max_dev)
fmin = -0.25
fmax = 0.25
self.receiver = digital_swig.constellation_receiver_cb(
self._constellation, self._phase_bw,
fmin, fmax)
# Do differential decoding based on phase change of symbols
if differential:
self.diffdec = gr.diff_decoder_bb(arity)
if gray_coded:
self.symbol_mapper = gr.map_bb(
mod_codes.invert_code(self._constellation.pre_diff_code()))
# unpack the k bit vector into a stream of bits
self.unpack = gr.unpack_k_bits_bb(self.bits_per_symbol())
if verbose:
self._print_verbage()
if log:
self._setup_logging()
# Connect and Initialize base class
blocks = [self, self.agc, self.freq_recov,
self.time_recov, self.receiver]
if differential:
blocks.append(self.diffdec)
if self._constellation.apply_pre_diff_code():
blocks.append(self.symbol_mapper)
blocks += [self.unpack, self]
self.connect(*blocks)
alle.append([0,0,0,0,0,1,0,0,0,0,1,1,1,1,0,1,0,1,0,1,1,1,0,1,0,1,0,0,0,0,1,0,0,1,0,1,0,0,0,0,0,0,1,0,0,0,0,0,0,0,0,0,0,1,0,0,1,1,1,1,0,0,0,0,0,0,0,1,1,0,0,1,0,1,0,0,0,1,1,0,1,0,1,1,0,1,0,0,0,0,1,0,0,0,0,1,1,0,1,1,0,0,0,1,1,1,1,0,0,0,0,1,0,0,0,0,1,0,0,0,1,0,0,0,0,1,0,0,1,1,1,1,1,1,1,1,1,1,0,1,1,0,0,0,0,0,0,0,0,0,0,0,1,0,0,0,0,1,1,0,0,1,1,0,1,0,1,0]) alle.append([0,0,0,0,0,1,0,0,0,1,0,0,1,0,1,0,0,1,1,0,0,0,0,0,1,0,0,1,0,1,1,0,1,0,1,0,0,0,0,0,0,0,1,0,0,0,0,0,0,0,0,0,0,1,0,1,0,0,1,0,0,0,0,0,0,0,0,1,1,0,0,1,0,1,0,0,0,1,0,1,0,1,1,0,0,0,1,1,0,0,1,0,0,0,0,1,1,0,1,1,0,0,0,1,1,0,1,0,0,0,0,1,0,1,0,1,0,1,1,1,1,0,1,1,0,1,0,0,1,1,1,1,1,1,1,1,1,0,0,1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,0,0,0,1,0,1,1,1,0,0,0]) alle.append([0,0,0,0,0,1,0,0,0,1,0,0,1,0,1,0,0,1,1,0,0,0,0,0,1,0,0,1,0,1,1,0,1,0,1,0,0,0,0,0,0,0,1,0,0,0,0,0,0,0,0,0,0,1,1,1,0,0,0,0,0,0,0,0,0,0,0,1,1,0,0,1,0,1,0,0,0,0,0,0,0,0,1,0,0,0,1,1,1,0,1,0,0,0,0,1,1,0,1,0,1,1,1,1,1,1,1,1,1,1,1,1,0,1,1,1,0,1,1,1,0,1,0,1,0,1,1,1,1,1,1,1,1,1,1,1,1,1,0,1,1,1,1,0,0,0,0,0,0,0,0,0,0,1,1,0,0,1,1,0,0,0,1,1,0,0,0,0]) alle.append([0,0,0,0,0,1,0,0,0,1,0,0,1,0,1,0,0,1,1,0,0,0,0,0,1,0,0,1,0,1,1,0,1,0,1,0,0,0,0,0,0,0,1,0,0,0,0,0,0,0,0,0,0,1,1,1,1,0,1,1,0,0,0,0,0,0,0,1,1,0,0,1,0,0,1,1,1,1,1,0,1,1,1,1,1,1,1,1,1,0,1,0,0,0,0,1,1,0,1,0,1,1,1,1,1,0,0,0,0,1,0,0,1,0,1,0,0,1,1,1,0,1,0,1,1,0,1,0,1,1,1,1,1,1,1,1,1,1,1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,0,0,0,1,0,0,1,0,1,0,0]) alle.append([0,0,0,0,0,1,0,0,0,1,0,0,1,0,1,0,0,1,1,0,0,0,0,0,1,0,0,1,0,1,1,0,1,0,1,0,0,0,0,0,0,0,1,0,0,0,0,0,0,0,0,0,0,1,1,1,1,1,1,0,0,0,0,0,0,0,0,1,1,0,0,1,0,0,1,1,1,1,1,0,1,0,0,1,1,1,1,1,1,0,1,0,0,0,0,1,1,0,1,0,1,1,1,1,0,1,0,1,1,1,0,0,0,0,0,1,0,1,1,1,0,1,0,1,0,1,1,1,1,1,1,1,1,1,1,1,1,0,0,0,1,1,1,0,0,0,0,0,0,0,0,0,1,0,0,0,0,0,0,1,0,1,1,1,1,1,0,0]) alle.append([0,0,0,0,1,1,0,0,0,0,1,1,1,1,0,1,1,1,0,1,1,1,1,0,1,0,0,0,0,0,0,0,0,1,0,0,0,0,0,1,0,1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,0,0,0,0,0,0,1,1,0,1,0,0,1,0,0,1,1,1,0,1,0,0,1,0,0,1,0,0,0,1,0,0,0,0,1,1,0,1,0,1,1,1,1,0,1,1,1,0,0,0,0,0,0,0,0,1,1,0,1,1,1,1,1,1,1,0,0,1,0,1,1,0,0,1,1,0,1,1,0,0,1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0]) alle.append([0,0,0,0,0,1,0,0,0,0,1,1,1,0,1,0,0,1,1,1,0,0,1,1,0,0,1,0,0,0,1,0,1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,0,1,1,1,1,1,0,0,0,0,0,0,0,1,1,0,0,0,1,1,1,1,0,0,0,1,0,1,0,1,0,1,0,1,0,0,1,0,0,0,0,1,1,0,1,0,1,0,1,1,0,1,1,0,1,1,0,1,0,0,1,0,1,0,0,1,0,1,1,1,0,1,0,0,0,1,1,1,0,1,0,1,1,1,1,0,1,0,0,0,0,0,0,0,0,0,0,1,0,0,0,0,0,1,1,1,1,0,0,0,1,0,1,1]) alle.append([0,0,0,0,0,1,0,0,0,0,1,1,1,1,0,1,0,1,1,1,1,1,0,0,1,0,1,1,0,1,1,1,0,1,1,1,0,0,0,1,0,1,1,0,0,0,0,0,0,1,0,0,0,0,0,0,1,1,1,1,0,0,0,0,0,0,0,1,1,0,1,0,0,1,0,0,1,0,0,0,0,1,0,0,0,0,1,0,0,0,1,0,0,0,0,1,1,0,1,0,1,1,0,0,1,1,1,1,0,0,0,1,1,0,1,1,1,0,1,0,0,0,0,0,1,0,0,1,0,1,1,0,1,1,1,0,0,0,0,0,0,1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0]) alle.append([0,0,0,0,0,1,0,0,0,1,0,0,1,0,1,0,0,1,1,0,0,0,0,0,1,0,0,1,0,1,1,0,1,0,1,0,0,0,0,0,0,0,1,0,0,0,0,0,0,0,0,0,1,0,0,0,1,1,1,1,0,0,0,0,0,0,0,1,1,0,0,1,0,0,0,1,0,1,0,1,1,1,1,0,0,0,1,0,1,0,1,0,0,0,0,1,1,0,1,0,1,1,0,0,0,0,0,0,0,1,1,0,1,1,1,0,1,0,0,1,0,0,0,1,0,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,0,1,0,0,0,0,0,0,0,0,0,1,0,0,0,0,0,0,0,0,0,0,1,0,1,1,1,0]) alle.append([0,0,0,0,0,1,0,0,0,1,0,0,1,0,1,0,0,1,1,0,0,0,0,0,1,0,0,1,0,1,1,0,1,0,1,0,0,0,0,0,0,0,1,0,0,0,0,0,0,0,0,0,1,0,0,1,0,1,0,0,0,0,0,0,0,0,0,1,1,0,0,0,1,1,1,1,1,0,0,1,0,0,0,1,0,0,0,0,1,0,1,0,0,0,0,1,1,0,1,0,1,0,1,0,1,0,0,1,0,1,1,0,0,1,1,0,1,0,0,1,0,0,0,0,1,1,1,0,1,1,1,1,1,1,1,1,1,1,1,1,0,1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,0,0,0,1,1,0,1,0,1,1,0]) alle.append([0,0,0,0,0,1,0,0,0,1,0,0,1,0,1,0,0,1,1,0,0,0,0,0,1,0,0,1,0,1,1,0,1,0,1,0,0,0,0,0,0,0,1,0,0,0,0,0,0,0,0,0,1,0,0,1,0,1,0,1,0,0,0,0,0,0,0,1,1,0,0,0,1,1,1,0,0,1,0,0,0,0,1,0,1,1,0,0,1,0,1,0,0,0,0,1,1,0,1,0,1,0,0,1,1,0,0,0,1,0,1,1,0,0,0,1,1,0,0,1,0,0,0,1,1,0,0,1,1,1,1,1,1,1,1,1,1,1,0,1,1,1,1,0,0,0,0,0,0,0,0,0,1,0,0,0,0,1,1,1,0,1,1,0,1,1,0,1]) src = ais.ais_source_f(alle[0], 500, True) dst = gr.vector_sink_f() slice = gr.binary_slicer_fb() diffdec = gr.diff_decoder_bb(2) invert = ais.invert10_bb() dst2 = gr.vector_sink_b() gaussian_taps = gr.firdes.gaussian(1,5,0.35,100) sqwave = (1,) * 5 taps = numpy.convolve(numpy.array(gaussian_taps),numpy.array(sqwave)) gaussian_filter = gr.interp_fir_filter_fff(5,taps) gange = gr.multiply_const_ff(0.3) lydut = audio.sink(9600*5,"default") filut = gr.file_sink(gr.sizeof_float,"filut.raw") #fg.connect(src,dst) #fg.connect(src,slice,diffdec,invert,dst2)
def __init__(self, options):
gr.hier_block2.__init__(
self,
"ais_demod",
gr.io_signature(1, 1, gr.sizeof_gr_complex), # Input signature
gr.io_signature(1, 1, gr.sizeof_char),
) # Output signature
self._samples_per_symbol = options.samples_per_symbol
self._bits_per_sec = options.bits_per_sec
self._samplerate = self._samples_per_symbol * self._bits_per_sec
self._gain_mu = options.gain_mu
self._mu = options.mu
self._omega_relative_limit = options.omega_relative_limit
self.fftlen = options.fftlen
# right now we are going to hardcode the different options for VA mode here. later on we can use configurable options
samples_per_symbol_viterbi = 2
bits_per_symbol = 2
samples_per_symbol = 6
samples_per_symbol_clockrec = samples_per_symbol / bits_per_symbol
BT = 0.4
data_rate = 9600.0
samp_rate = options.samp_rate
self.gmsk_sync = gmsk_sync.square_and_fft_sync(self._samplerate, self._bits_per_sec, self.fftlen)
if options.viterbi is True:
# calculate the required decimation and interpolation to achieve the desired samples per symbol
denom = gcd(data_rate * samples_per_symbol, samp_rate)
cr_interp = int(data_rate * samples_per_symbol / denom)
cr_decim = int(samp_rate / denom)
self.resample = blks2.rational_resampler_ccc(cr_interp, cr_decim)
# here we take a different tack and use A.A.'s CPM decomposition technique
self.clockrec = gr.clock_recovery_mm_cc(
samples_per_symbol_clockrec, 0.005 * 0.005 * 0.25, 0.5, 0.005, 0.0005
) # might have to futz with the max. deviation
(fsm, constellation, MF, N, f0T) = make_gmsk(
samples_per_symbol_viterbi, BT
) # calculate the decomposition required for demodulation
self.costas = gr.costas_loop_cc(
0.015, 0.015 * 0.015 * 0.25, 100e-6, -100e-6, 4
) # does fine freq/phase synchronization. should probably calc the coeffs instead of hardcode them.
self.streams2stream = gr.streams_to_stream(int(gr.sizeof_gr_complex * 1), int(N))
self.mf0 = gr.fir_filter_ccc(
samples_per_symbol_viterbi, MF[0].conjugate()
) # two matched filters for decomposition
self.mf1 = gr.fir_filter_ccc(samples_per_symbol_viterbi, MF[1].conjugate())
self.fo = gr.sig_source_c(
samples_per_symbol_viterbi, gr.GR_COS_WAVE, -f0T, 1, 0
) # the memoryless modulation component of the decomposition
self.fomult = gr.multiply_cc(1)
self.trellis = trellis.viterbi_combined_cb(
fsm, int(data_rate), -1, -1, int(N), constellation, trellis.TRELLIS_EUCLIDEAN
) # the actual Viterbi decoder
else:
# this is probably not optimal and someone who knows what they're doing should correct me
self.datafiltertaps = gr.firdes.root_raised_cosine(
10, # gain
self._samplerate * 32, # sample rate
self._bits_per_sec, # symbol rate
0.4, # alpha, same as BT?
50 * 32,
) # no. of taps
self.datafilter = gr.fir_filter_fff(1, self.datafiltertaps)
sensitivity = (math.pi / 2) / self._samples_per_symbol
self.demod = gr.quadrature_demod_cf(sensitivity) # param is gain
# self.clockrec = digital.clock_recovery_mm_ff(self._samples_per_symbol,0.25*self._gain_mu*self._gain_mu,self._mu,self._gain_mu,self._omega_relative_limit)
self.clockrec = gr.pfb_clock_sync_ccf(self._samples_per_symbol, 0.04, self.datafiltertaps, 32, 0, 1.15)
self.tcslicer = digital.digital.binary_slicer_fb()
# self.dfe = digital.digital.lms_dd_equalizer_cc(
# 32,
# 0.005,
# 1,
# digital.digital.constellation_bpsk()
# )
# self.delay = gr.delay(gr.sizeof_float, 64 + 16) #the correlator delays 64 bits, and the LMS delays some as well.
self.slicer = digital.digital.binary_slicer_fb()
# self.training_correlator = digital.correlate_access_code_bb("1100110011001100", 0)
# self.cma = digital.cma_equalizer_cc
# just a note here: a complex combined quad demod/slicer could be based on if's rather than an actual quad demod, right?
# in fact all the constellation decoders up to QPSK could operate on complex data w/o doing the whole atan thing
self.diff = gr.diff_decoder_bb(2)
self.invert = ais.invert() # NRZI signal diff decoded and inverted should give original signal
self.connect(self, self.gmsk_sync)
if options.viterbi is False:
self.connect(self.gmsk_sync, self.clockrec, self.demod, self.slicer, self.diff, self.invert, self)
# self.connect(self.gmsk_sync, self.demod, self.clockrec, self.tcslicer, self.training_correlator)
# self.connect(self.clockrec, self.delay, (self.dfe, 0))
# self.connect(self.training_correlator, (self.dfe, 1))
# self.connect(self.dfe, self.slicer, self.diff, self.invert, self)
else:
self.connect(self.gmsk_sync, self.costas, self.resample, self.clockrec)
self.connect(self.clockrec, (self.fomult, 0))
self.connect(self.fo, (self.fomult, 1))
self.connect(self.fomult, self.mf0)
self.connect(self.fomult, self.mf1)
self.connect(self.mf0, (self.streams2stream, 0))
self.connect(self.mf1, (self.streams2stream, 1))
self.connect(self.streams2stream, self.trellis, self.diff, self.invert, self)
src = audio.source(samplerate, "hw:1")
pluss = gr.add_const_ff(0.0)
lpcoeffs = gr.firdes.low_pass(1, samplerate, 8000, 3000)
lpfilter = gr.fir_filter_fff(1, lpcoeffs)
forsterk = gr.multiply_const_ff(5)
clockrec = gr.clock_recovery_mm_ff(
float(samplerate) / 9600, 0.25 * 0.175 * 0.175, 0.5, 0.175, 0.005)
slicer = gr.binary_slicer_fb()
# Parameters: ([mysql-server],[database name],[database user],[database password])
datadec = ais.ais_decoder_mysql("localhost", "diverse", "ruben", "elg")
# You should use the create_mysql.sql to create the necessary tables
# in the database.
# See create_mysql.txt for help. Those files can be found in the root folder of
# the source tree.
diff = gr.diff_decoder_bb(2)
invert = ais.invert10_bb()
fg.connect(src, pluss, lpfilter, forsterk, clockrec, slicer, diff, invert,
datadec)
fg.start()
raw_input("Receives AIS from soundcard ")
fg.stop()
print "Received correctly: ", datadec.received()
print "Wrong CRC: ", datadec.lost()
print "Wrong Size: ", datadec.lost2()
def __init__(self):
gr.top_block.__init__ (self)
parser=OptionParser(option_class=eng_option)
parser.add_option("-R", "--rx-subdev-spec", type="subdev", default=None,
help="select USRP Rx side A or B (default=A)")
parser.add_option("-f", "--freq", type="eng_float", default=91.2e6,
help="set frequency to FREQ", metavar="FREQ")
parser.add_option("-g", "--gain", type="eng_float", default=None,
help="set gain in dB")
parser.add_option("-s", "--squelch", type="eng_float", default=0,
help="set squelch level (default is 0)")
parser.add_option("-V", "--volume", type="eng_float", default=None,
help="set volume (default is midpoint)")
parser.add_option("-O", "--audio-output", type="string", default="plughw:0,0",
help="pcm device name (default is plughw:0,0)")
(options, args) = parser.parse_args()
if len(args) != 0:
parser.print_help()
sys.exit(1)
# connect to USRP
usrp_decim = 250
self.u = usrp.source_c(0, usrp_decim)
print "USRP Serial: ", self.u.serial_number()
demod_rate = self.u.adc_rate() / usrp_decim # 256 kS/s
audio_decim = 8
audio_rate = demod_rate / audio_decim # 32 kS/s
if options.rx_subdev_spec is None:
options.rx_subdev_spec = usrp.pick_subdev(self.u, dblist)
self.u.set_mux(usrp.determine_rx_mux_value(self.u, options.rx_subdev_spec))
self.subdev = usrp.selected_subdev(self.u, options.rx_subdev_spec)
print "Using d'board", self.subdev.side_and_name()
# gain, volume, frequency
self.gain = options.gain
if options.gain is None:
self.gain = self.subdev.gain_range()[1]
self.vol = options.volume
if self.vol is None:
g = self.volume_range()
self.vol = float(g[0]+g[1])/2
self.freq = options.freq
if abs(self.freq) < 1e6:
self.freq *= 1e6
print "Volume:%r, Gain:%r, Freq:%3.1f MHz" % (self.vol, self.gain, self.freq/1e6)
# channel filter, wfm_rcv_pll
chan_filt_coeffs = optfir.low_pass(
1, # gain
demod_rate, # rate
80e3, # passband cutoff
115e3, # stopband cutoff
0.1, # passband ripple
60) # stopband attenuation
self.chan_filt = gr.fir_filter_ccf (1, chan_filt_coeffs)
self.guts = blks2.wfm_rcv_pll (demod_rate, audio_decim)
self.connect(self.u, self.chan_filt, self.guts)
# volume control, audio sink
self.volume_control_l = gr.multiply_const_ff(self.vol)
self.volume_control_r = gr.multiply_const_ff(self.vol)
self.audio_sink = audio.sink(int(audio_rate), options.audio_output, False)
self.connect ((self.guts, 0), self.volume_control_l, (self.audio_sink, 0))
self.connect ((self.guts, 1), self.volume_control_r, (self.audio_sink, 1))
# pilot channel filter (band-pass, 18.5-19.5kHz)
pilot_filter_coeffs = gr.firdes.band_pass(
1, # gain
demod_rate, # sampling rate
18.5e3, # low cutoff
19.5e3, # high cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.pilot_filter = gr.fir_filter_fff(1, pilot_filter_coeffs)
self.connect(self.guts.fm_demod, self.pilot_filter)
# RDS channel filter (band-pass, 54-60kHz)
rds_filter_coeffs = gr.firdes.band_pass(
1, # gain
demod_rate, # sampling rate
54e3, # low cutoff
60e3, # high cutoff
3e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_filter = gr.fir_filter_fff(1, rds_filter_coeffs)
self.connect(self.guts.fm_demod, self.rds_filter)
# create 57kHz subcarrier from 19kHz pilot, downconvert RDS channel
self.mixer = gr.multiply_ff()
self.connect(self.pilot_filter, (self.mixer, 0))
self.connect(self.pilot_filter, (self.mixer, 1))
self.connect(self.pilot_filter, (self.mixer, 2))
self.connect(self.rds_filter, (self.mixer, 3))
# low-pass the baseband RDS signal at 1.5kHz
rds_bb_filter_coeffs = gr.firdes.low_pass(
1, # gain
demod_rate, # sampling rate
1.5e3, # passband cutoff
2e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_bb_filter = gr.fir_filter_fff(1, rds_bb_filter_coeffs)
self.connect(self.mixer, self.rds_bb_filter)
# 1187.5bps = 19kHz/16
self.rds_clock = rds.freq_divider(16)
clock_taps = gr.firdes.low_pass(
1, # gain
demod_rate, # sampling rate
1.2e3, # passband cutoff
1.5e3, # transition width
gr.firdes.WIN_HANN)
self.clock_filter = gr.fir_filter_fff(1, clock_taps)
self.connect(self.pilot_filter, self.rds_clock, self.clock_filter)
# bpsk_demod, diff_decoder, rds_decoder
self.bpsk_demod = rds.bpsk_demod(demod_rate)
self.differential_decoder = gr.diff_decoder_bb(2)
self.msgq = gr.msg_queue()
self.rds_decoder = rds.data_decoder(self.msgq)
self.connect(self.rds_bb_filter, (self.bpsk_demod, 0))
self.connect(self.clock_filter, (self.bpsk_demod, 1))
self.connect(self.bpsk_demod, self.differential_decoder)
self.connect(self.differential_decoder, self.rds_decoder)
# set initial values
self.subdev.set_gain(self.gain)
self.set_vol(self.vol)
self.set_freq(self.freq)
def __init__(self):
gr.top_block.__init__(self)
parser = OptionParser(option_class=eng_option)
parser.add_option("-R",
"--rx-subdev-spec",
type="subdev",
default=None,
help="select USRP Rx side A or B (default=A)")
parser.add_option("-f",
"--freq",
type="eng_float",
default=91.2e6,
help="set frequency to FREQ",
metavar="FREQ")
parser.add_option("-g",
"--gain",
type="eng_float",
default=None,
help="set gain in dB")
parser.add_option("-s",
"--squelch",
type="eng_float",
default=0,
help="set squelch level (default is 0)")
parser.add_option("-V",
"--volume",
type="eng_float",
default=None,
help="set volume (default is midpoint)")
parser.add_option("-O",
"--audio-output",
type="string",
default="plughw:0,0",
help="pcm device name (default is plughw:0,0)")
(options, args) = parser.parse_args()
if len(args) != 0:
parser.print_help()
sys.exit(1)
# connect to USRP
usrp_decim = 250
self.u = usrp.source_c(0, usrp_decim)
print "USRP Serial: ", self.u.serial_number()
demod_rate = self.u.adc_rate() / usrp_decim # 256 kS/s
audio_decim = 8
audio_rate = demod_rate / audio_decim # 32 kS/s
if options.rx_subdev_spec is None:
options.rx_subdev_spec = usrp.pick_subdev(self.u, dblist)
self.u.set_mux(
usrp.determine_rx_mux_value(self.u, options.rx_subdev_spec))
self.subdev = usrp.selected_subdev(self.u, options.rx_subdev_spec)
print "Using d'board", self.subdev.side_and_name()
# gain, volume, frequency
self.gain = options.gain
if options.gain is None:
self.gain = self.subdev.gain_range()[1]
self.vol = options.volume
if self.vol is None:
g = self.volume_range()
self.vol = float(g[0] + g[1]) / 2
self.freq = options.freq
if abs(self.freq) < 1e6:
self.freq *= 1e6
print "Volume:%r, Gain:%r, Freq:%3.1f MHz" % (self.vol, self.gain,
self.freq / 1e6)
# channel filter, wfm_rcv_pll
chan_filt_coeffs = optfir.low_pass(
1, # gain
demod_rate, # rate
80e3, # passband cutoff
115e3, # stopband cutoff
0.1, # passband ripple
60) # stopband attenuation
self.chan_filt = gr.fir_filter_ccf(1, chan_filt_coeffs)
self.guts = blks2.wfm_rcv_pll(demod_rate, audio_decim)
self.connect(self.u, self.chan_filt, self.guts)
# volume control, audio sink
self.volume_control_l = gr.multiply_const_ff(self.vol)
self.volume_control_r = gr.multiply_const_ff(self.vol)
self.audio_sink = audio.sink(int(audio_rate), options.audio_output,
False)
self.connect((self.guts, 0), self.volume_control_l,
(self.audio_sink, 0))
self.connect((self.guts, 1), self.volume_control_r,
(self.audio_sink, 1))
# pilot channel filter (band-pass, 18.5-19.5kHz)
pilot_filter_coeffs = gr.firdes.band_pass(
1, # gain
demod_rate, # sampling rate
18.5e3, # low cutoff
19.5e3, # high cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.pilot_filter = gr.fir_filter_fff(1, pilot_filter_coeffs)
self.connect(self.guts.fm_demod, self.pilot_filter)
# RDS channel filter (band-pass, 54-60kHz)
rds_filter_coeffs = gr.firdes.band_pass(
1, # gain
demod_rate, # sampling rate
54e3, # low cutoff
60e3, # high cutoff
3e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_filter = gr.fir_filter_fff(1, rds_filter_coeffs)
self.connect(self.guts.fm_demod, self.rds_filter)
# create 57kHz subcarrier from 19kHz pilot, downconvert RDS channel
self.mixer = gr.multiply_ff()
self.connect(self.pilot_filter, (self.mixer, 0))
self.connect(self.pilot_filter, (self.mixer, 1))
self.connect(self.pilot_filter, (self.mixer, 2))
self.connect(self.rds_filter, (self.mixer, 3))
# low-pass the baseband RDS signal at 1.5kHz
rds_bb_filter_coeffs = gr.firdes.low_pass(
1, # gain
demod_rate, # sampling rate
1.5e3, # passband cutoff
2e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_bb_filter = gr.fir_filter_fff(1, rds_bb_filter_coeffs)
self.connect(self.mixer, self.rds_bb_filter)
# 1187.5bps = 19kHz/16
self.rds_clock = rds.freq_divider(16)
clock_taps = gr.firdes.low_pass(
1, # gain
demod_rate, # sampling rate
1.2e3, # passband cutoff
1.5e3, # transition width
gr.firdes.WIN_HANN)
self.clock_filter = gr.fir_filter_fff(1, clock_taps)
self.connect(self.pilot_filter, self.rds_clock, self.clock_filter)
# bpsk_demod, diff_decoder, rds_decoder
self.bpsk_demod = rds.bpsk_demod(demod_rate)
self.differential_decoder = gr.diff_decoder_bb(2)
self.msgq = gr.msg_queue()
self.rds_decoder = rds.data_decoder(self.msgq)
self.connect(self.rds_bb_filter, (self.bpsk_demod, 0))
self.connect(self.clock_filter, (self.bpsk_demod, 1))
self.connect(self.bpsk_demod, self.differential_decoder)
self.connect(self.differential_decoder, self.rds_decoder)
# set initial values
self.subdev.set_gain(self.gain)
self.set_vol(self.vol)
self.set_freq(self.freq)
def __init__(self,frame,panel,vbox,argv):
stdgui2.std_top_block.__init__ (self,frame,panel,vbox,argv)
parser=OptionParser(option_class=eng_option)
parser.add_option("-R", "--rx-subdev-spec", type="subdev", default=None,
help="select USRP Rx side A or B (default=A)")
parser.add_option("-f", "--freq", type="eng_float", default=91.2e6,
help="set frequency to FREQ", metavar="FREQ")
parser.add_option("-g", "--gain", type="eng_float", default=None,
help="set gain in dB")
# FIXME add squelch
parser.add_option("-s", "--squelch", type="eng_float", default=0,
help="set squelch level (default is 0)")
parser.add_option("-V", "--volume", type="eng_float", default=None,
help="set volume (default is midpoint)")
parser.add_option("-O", "--audio-output", type="string", default="plughw:0,0",
help="pcm device name (default is plughw:0,0)")
# print help when called with wrong arguments
(options, args) = parser.parse_args()
if len(args) != 0:
parser.print_help()
sys.exit(1)
# connect to USRP
usrp_decim = 250
self.u = usrp.source_c(0, usrp_decim)
print "USRP Serial:", self.u.serial_number()
usrp_rate = self.u.adc_rate() / usrp_decim # 256 kS/s
print "usrp_rate =", usrp_rate
audio_decim = 8
audio_rate = usrp_rate / audio_decim # 32 kS/s
print "audio_rate =", audio_rate
#if options.rx_subdev_spec is None:
# options.rx_subdev_spec = usrp.pick_subdev(self.u, dblist)
self.u.set_mux(usrp.determine_rx_mux_value(self.u, options.rx_subdev_spec))
self.subdev = usrp.selected_subdev(self.u, options.rx_subdev_spec)
print "Using d'board", self.subdev.side_and_name()
# gain, volume, frequency
self.gain = options.gain
if options.gain is None:
g = self.subdev.gain_range()
self.gain = float(g[0]+g[1])/2
self.vol = options.volume
if self.vol is None:
g = self.volume_range()
self.vol = float(g[0]+g[1])/2
self.freq = options.freq
print "Volume:%r, Gain:%r, Freq:%3.1f MHz" % (self.vol, self.gain, self.freq/1e6)
# channel filter
chan_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
usrp_rate, # sampling rate
80e3, # passband cutoff
35e3, # transition width
gr.firdes.WIN_HAMMING)
self.chan_filter = gr.fir_filter_ccf(1, chan_filter_coeffs)
print "# channel filter:", len(chan_filter_coeffs), "taps"
# PLL-based WFM demod
fm_alpha = 0.25 * 250e3 * math.pi / usrp_rate # 0.767
fm_beta = fm_alpha * fm_alpha / 4.0 # 0.147
fm_max_freq = 2.0 * math.pi * 90e3 / usrp_rate # 2.209
self.fm_demod = gr.pll_freqdet_cf(
#fm_alpha, # phase gain
#fm_beta, # freq gain
1.0, # Loop BW
fm_max_freq, # in radians/sample
-fm_max_freq)
self.fm_demod.set_alpha(fm_alpha)
self.fm_demod.set_beta(fm_beta)
self.connect(self.u, self.chan_filter, self.fm_demod)
# L+R, pilot, L-R, RDS filters
lpr_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
usrp_rate, # sampling rate
15e3, # passband cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.lpr_filter = gr.fir_filter_fff(audio_decim, lpr_filter_coeffs)
pilot_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
usrp_rate, # sampling rate
19e3-500, # low cutoff
19e3+500, # high cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.pilot_filter = gr.fir_filter_fff(1, pilot_filter_coeffs)
dsbsc_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
usrp_rate, # sampling rate
38e3-15e3/2, # low cutoff
38e3+15e3/2, # high cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.dsbsc_filter = gr.fir_filter_fff(1, dsbsc_filter_coeffs)
rds_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
usrp_rate, # sampling rate
57e3-3e3, # low cutoff
57e3+3e3, # high cutoff
3e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_filter = gr.fir_filter_fff(1, rds_filter_coeffs)
print "# lpr filter:", len(lpr_filter_coeffs), "taps"
print "# pilot filter:", len(pilot_filter_coeffs), "taps"
print "# dsbsc filter:", len(dsbsc_filter_coeffs), "taps"
print "# rds filter:", len(rds_filter_coeffs), "taps"
self.connect(self.fm_demod, self.lpr_filter)
self.connect(self.fm_demod, self.pilot_filter)
self.connect(self.fm_demod, self.dsbsc_filter)
self.connect(self.fm_demod, self.rds_filter)
# down-convert L-R, RDS
self.stereo_baseband = gr.multiply_ff()
self.connect(self.pilot_filter, (self.stereo_baseband, 0))
self.connect(self.pilot_filter, (self.stereo_baseband, 1))
self.connect(self.dsbsc_filter, (self.stereo_baseband, 2))
self.rds_baseband = gr.multiply_ff()
self.connect(self.pilot_filter, (self.rds_baseband, 0))
self.connect(self.pilot_filter, (self.rds_baseband, 1))
self.connect(self.pilot_filter, (self.rds_baseband, 2))
self.connect(self.rds_filter, (self.rds_baseband, 3))
# low-pass and downsample L-R
lmr_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
usrp_rate, # sampling rate
15e3, # passband cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.lmr_filter = gr.fir_filter_fff(audio_decim, lmr_filter_coeffs)
self.connect(self.stereo_baseband, self.lmr_filter)
# create L, R from L-R, L+R
self.left = gr.add_ff()
self.right = gr.sub_ff()
self.connect(self.lpr_filter, (self.left, 0))
self.connect(self.lmr_filter, (self.left, 1))
self.connect(self.lpr_filter, (self.right, 0))
self.connect(self.lmr_filter, (self.right, 1))
# volume control, complex2flot, audio sink
self.volume_control_l = gr.multiply_const_ff(self.vol)
self.volume_control_r = gr.multiply_const_ff(self.vol)
output_audio_rate = 48000
self.audio_sink = audio.sink(int(output_audio_rate),
options.audio_output, False)
#self.connect(self.left, self.volume_control_l, (self.audio_sink, 0))
#self.connect(self.right, self.volume_control_r, (self.audio_sink, 1))
self.resamp_L = blks2.rational_resampler_fff(interpolation=output_audio_rate,decimation=audio_rate,taps=None,fractional_bw=None,)
self.resamp_R = blks2.rational_resampler_fff(interpolation=output_audio_rate,decimation=audio_rate,taps=None,fractional_bw=None,)
self.connect(self.left, self.volume_control_l, self.resamp_L, (self.audio_sink, 0))
self.connect(self.right, self.volume_control_r, self.resamp_R, (self.audio_sink, 1))
# low-pass the baseband RDS signal at 1.5kHz
rds_bb_filter_coeffs = gr.firdes.low_pass(
1, # gain
usrp_rate, # sampling rate
1.5e3, # passband cutoff
2e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_bb_filter = gr.fir_filter_fff(audio_decim, rds_bb_filter_coeffs)
print "# rds bb filter:", len(rds_bb_filter_coeffs), "taps"
self.connect(self.rds_baseband, self.rds_bb_filter)
# 1187.5bps = 19kHz/16
self.clock_divider = rds.freq_divider(16)
rds_clock_taps = gr.firdes.low_pass(
1, # gain
usrp_rate, # sampling rate
1.2e3, # passband cutoff
1.5e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_clock = gr.fir_filter_fff(audio_decim, rds_clock_taps)
print "# rds clock filter:", len(rds_clock_taps), "taps"
self.connect(self.pilot_filter, self.clock_divider, self.rds_clock)
# bpsk_demod, diff_decoder, rds_decoder
self.bpsk_demod = rds.bpsk_demod(audio_rate)
self.differential_decoder = gr.diff_decoder_bb(2)
self.msgq = gr.msg_queue()
self.rds_decoder = rds.data_decoder(self.msgq)
self.connect(self.rds_bb_filter, (self.bpsk_demod, 0))
self.connect(self.rds_clock, (self.bpsk_demod, 1))
self.connect(self.bpsk_demod, self.differential_decoder)
self.connect(self.differential_decoder, self.rds_decoder)
self.frame = frame
self.panel = panel
self._build_gui(vbox, usrp_rate, audio_rate)
self.set_gain(self.gain)
self.set_vol(self.vol)
if not(self.set_freq(self.freq)):
self._set_status_msg("Failed to set initial frequency")
def __init__(self,
constellation,
samples_per_symbol=_def_samples_per_symbol,
differential=_def_differential,
excess_bw=_def_excess_bw,
gray_coded=True,
freq_bw=_def_freq_bw,
timing_bw=_def_timing_bw,
phase_bw=_def_phase_bw,
verbose=_def_verbose,
log=_def_log):
"""
Hierarchical block for RRC-filtered differential generic demodulation.
The input is the complex modulated signal at baseband.
The output is a stream of bits packed 1 bit per byte (LSB)
@param constellation: determines the modulation type
@type constellation: gnuradio.digital.gr_constellation
@param samples_per_symbol: samples per symbol >= 2
@type samples_per_symbol: float
@param excess_bw: Root-raised cosine filter excess bandwidth
@type excess_bw: float
@param gray_coded: turn gray coding on/off
@type gray_coded: bool
@param freq_bw: loop filter lock-in bandwidth
@type freq_bw: float
@param timing_bw: timing recovery loop lock-in bandwidth
@type timing_bw: float
@param phase_bw: phase recovery loop bandwidth
@type phase_bw: float
@param verbose: Print information about modulator?
@type verbose: bool
@param debug: Print modualtion data to files?
@type debug: bool
"""
gr.hier_block2.__init__(
self,
"generic_demod",
gr.io_signature(1, 1, gr.sizeof_gr_complex), # Input signature
gr.io_signature(1, 1, gr.sizeof_char)) # Output signature
self._constellation = constellation.base()
self._samples_per_symbol = samples_per_symbol
self._excess_bw = excess_bw
self._phase_bw = phase_bw
self._freq_bw = freq_bw
self._timing_bw = timing_bw
self._timing_max_dev = _def_timing_max_dev
self._differential = differential
if self._samples_per_symbol < 2:
raise TypeError, ("sbp must be >= 2, is %d" %
self._samples_per_symbol)
arity = pow(2, self.bits_per_symbol())
nfilts = 32
ntaps = 11 * int(self._samples_per_symbol * nfilts)
# Automatic gain control
self.agc = gr.agc2_cc(0.6e-1, 1e-3, 1, 1, 100)
# Frequency correction
fll_ntaps = 55
self.freq_recov = digital_swig.fll_band_edge_cc(
self._samples_per_symbol, self._excess_bw, fll_ntaps,
self._freq_bw)
# symbol timing recovery with RRC data filter
taps = gr.firdes.root_raised_cosine(nfilts,
nfilts * self._samples_per_symbol,
1.0, self._excess_bw, ntaps)
self.time_recov = gr.pfb_clock_sync_ccf(self._samples_per_symbol,
self._timing_bw, taps, nfilts,
nfilts // 2,
self._timing_max_dev)
fmin = -0.25
fmax = 0.25
self.receiver = digital_swig.constellation_receiver_cb(
self._constellation, self._phase_bw, fmin, fmax)
# Do differential decoding based on phase change of symbols
if differential:
self.diffdec = gr.diff_decoder_bb(arity)
if gray_coded:
self.symbol_mapper = gr.map_bb(
mod_codes.invert_code(self._constellation.pre_diff_code()))
# unpack the k bit vector into a stream of bits
self.unpack = gr.unpack_k_bits_bb(self.bits_per_symbol())
if verbose:
self._print_verbage()
if log:
self._setup_logging()
# Connect and Initialize base class
blocks = [
self, self.agc, self.freq_recov, self.time_recov, self.receiver
]
if differential:
blocks.append(self.diffdec)
if self._constellation.apply_pre_diff_code():
blocks.append(self.symbol_mapper)
blocks += [self.unpack, self]
self.connect(*blocks)
def __init__(self,frame,panel,vbox,argv):
stdgui2.std_top_block.__init__ (self,frame,panel,vbox,argv)
parser=OptionParser(option_class=eng_option)
parser.add_option("-V", "--volume", type="eng_float", default=None,
help="set volume (default is midpoint)")
parser.add_option("-O", "--audio-output", type="string", default="plughw:0,0",
help="pcm device name (default is plughw:0,0)")
# print help when called with wrong arguments
(options, args) = parser.parse_args()
if len(args) != 0:
parser.print_help()
sys.exit(1)
self.file_source = gr.file_source(gr.sizeof_gr_complex*1, offline_samples, True)
chan_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
usrp_rate, # sampling rate
80e3, # passband cutoff
35e3, # transition width
gr.firdes.WIN_HAMMING)
self.chan_filter = gr.fir_filter_ccf(1, chan_filter_coeffs)
print "# channel filter:", len(chan_filter_coeffs), "taps"
# PLL-based WFM demod
fm_alpha = 0.25 * 250e3 * math.pi / usrp_rate # 0.767
fm_beta = fm_alpha * fm_alpha / 4.0 # 0.147
fm_max_freq = 2.0 * math.pi * 90e3 / usrp_rate # 2.209
self.fm_demod = gr.pll_freqdet_cf(
fm_alpha, # phase gain
fm_beta, # freq gain
fm_max_freq, # in radians/sample
-fm_max_freq)
self.connect(self.file_source, self.chan_filter, self.fm_demod)
# L+R, pilot, L-R, RDS filters
lpr_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
usrp_rate, # sampling rate
15e3, # passband cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.lpr_filter = gr.fir_filter_fff(audio_decim, lpr_filter_coeffs)
pilot_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
usrp_rate, # sampling rate
19e3-500, # low cutoff
19e3+500, # high cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.pilot_filter = gr.fir_filter_fff(1, pilot_filter_coeffs)
dsbsc_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
usrp_rate, # sampling rate
38e3-15e3/2, # low cutoff
38e3+15e3/2, # high cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.dsbsc_filter = gr.fir_filter_fff(1, dsbsc_filter_coeffs)
rds_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
usrp_rate, # sampling rate
57e3-3e3, # low cutoff
57e3+3e3, # high cutoff
3e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_filter = gr.fir_filter_fff(1, rds_filter_coeffs)
print "# lpr filter:", len(lpr_filter_coeffs), "taps"
print "# pilot filter:", len(pilot_filter_coeffs), "taps"
print "# dsbsc filter:", len(dsbsc_filter_coeffs), "taps"
print "# rds filter:", len(rds_filter_coeffs), "taps"
self.connect(self.fm_demod, self.lpr_filter)
self.connect(self.fm_demod, self.pilot_filter)
self.connect(self.fm_demod, self.dsbsc_filter)
self.connect(self.fm_demod, self.rds_filter)
# down-convert L-R, RDS
self.stereo_baseband = gr.multiply_ff()
self.connect(self.pilot_filter, (self.stereo_baseband, 0))
self.connect(self.pilot_filter, (self.stereo_baseband, 1))
self.connect(self.dsbsc_filter, (self.stereo_baseband, 2))
self.rds_baseband = gr.multiply_ff()
self.connect(self.pilot_filter, (self.rds_baseband, 0))
self.connect(self.pilot_filter, (self.rds_baseband, 1))
self.connect(self.pilot_filter, (self.rds_baseband, 2))
self.connect(self.rds_filter, (self.rds_baseband, 3))
# low-pass and downsample L-R
lmr_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
usrp_rate, # sampling rate
15e3, # passband cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.lmr_filter = gr.fir_filter_fff(audio_decim, lmr_filter_coeffs)
self.connect(self.stereo_baseband, self.lmr_filter)
# create L, R from L-R, L+R
self.left = gr.add_ff()
self.right = gr.sub_ff()
self.connect(self.lpr_filter, (self.left, 0))
self.connect(self.lmr_filter, (self.left, 1))
self.connect(self.lpr_filter, (self.right, 0))
self.connect(self.lmr_filter, (self.right, 1))
# send audio to null sink
self.null0 = gr.null_sink(gr.sizeof_float)
self.null1 = gr.null_sink(gr.sizeof_float)
self.connect(self.left, self.null0)
self.connect(self.right, self.null1)
# low-pass the baseband RDS signal at 1.5kHz
rds_bb_filter_coeffs = gr.firdes.low_pass(
1, # gain
usrp_rate, # sampling rate
1.5e3, # passband cutoff
2e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_bb_filter = gr.fir_filter_fff(audio_decim, rds_bb_filter_coeffs)
print "# rds bb filter:", len(rds_bb_filter_coeffs), "taps"
self.connect(self.rds_baseband, self.rds_bb_filter)
# 1187.5bps = 19kHz/16
self.clock_divider = rds.freq_divider(16)
rds_clock_taps = gr.firdes.low_pass(
1, # gain
usrp_rate, # sampling rate
1.2e3, # passband cutoff
1.5e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_clock = gr.fir_filter_fff(audio_decim, rds_clock_taps)
print "# rds clock filter:", len(rds_clock_taps), "taps"
self.connect(self.pilot_filter, self.clock_divider, self.rds_clock)
# bpsk_demod, diff_decoder, rds_decoder
self.bpsk_demod = rds.bpsk_demod(audio_rate)
self.differential_decoder = gr.diff_decoder_bb(2)
self.msgq = gr.msg_queue()
self.rds_decoder = rds.data_decoder(self.msgq)
self.connect(self.rds_bb_filter, (self.bpsk_demod, 0))
self.connect(self.rds_clock, (self.bpsk_demod, 1))
self.connect(self.bpsk_demod, self.differential_decoder)
self.connect(self.differential_decoder, self.rds_decoder)
self.frame = frame
self.panel = panel
self._build_gui(vbox, usrp_rate, audio_rate)
def __init__(self):
gr.top_block.__init__ (self)
parser=OptionParser(option_class=eng_option)
parser.add_option("-H", "--hostname", type="string", default="localhost",
help="set hostname of generic sdr")
parser.add_option("-P", "--portnum", type="int", default=None,
help="set portnum of generic sdr")
parser.add_option("-r", "--sdr_rate", type="eng_float", default=250e3,
help="set sample rate of generic sdr")
parser.add_option("-V", "--volume", type="eng_float", default=None,
help="set volume (default is midpoint)")
parser.add_option("-O", "--audio-output", type="string", default="plughw:0,0",
help="pcm device name (default is plughw:0,0)")
# print help when called with wrong arguments
(options, args) = parser.parse_args()
if len(args) != 0:
parser.print_help()
sys.exit(1)
self.vol = options.volume
if self.vol is None:
self.vol = 0.1
# connect to generic SDR
sdr_rate = options.sdr_rate
audio_decim = 8
audio_rate = int(sdr_rate/audio_decim)
print "audio_rate = ", audio_rate
self.interleaved_short_to_complex = gr.interleaved_short_to_complex()
self.char_to_short = gr.char_to_short(1)
self.sdr_source = grc_blks2.tcp_source(
itemsize=gr.sizeof_char*1,
addr=options.hostname,
port=options.portnum,
server=False
)
# self.sdr_source = gr.file_source(1, 'sdrs_baseband.dat')
# self.throttle = gr.throttle(1, 500e3)
# self.connect(self.sdr_source, self.file_sink)
self.logger = gr.file_sink(1, 'log.out')
self.connect(self.sdr_source, self.logger)
# channel filter
chan_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
sdr_rate, # sampling rate
80e3, # passband cutoff
35e3, # transition width
gr.firdes.WIN_HAMMING)
self.chan_filter = gr.fir_filter_ccf(1, chan_filter_coeffs)
# print "# channel filter:", len(chan_filter_coeffs), "taps"
# PLL-based WFM demod
fm_alpha = 0.25 * 250e3 * math.pi / sdr_rate # 0.767
fm_beta = fm_alpha * fm_alpha / 4.0 # 0.147
fm_max_freq = 2.0 * math.pi * 90e3 / sdr_rate # 2.209
self.fm_demod = gr.pll_freqdet_cf(
1.0, # Loop BW
fm_max_freq, # in radians/sample
-fm_max_freq)
self.fm_demod.set_alpha(fm_alpha)
self.fm_demod.set_beta(fm_beta)
self.connect(self.sdr_source, self.char_to_short)
self.connect(self.char_to_short, self.interleaved_short_to_complex)
self.connect(self.interleaved_short_to_complex, self.chan_filter, self.fm_demod)
# L+R, pilot, L-R, RDS filters
lpr_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
sdr_rate, # sampling rate
15e3, # passband cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.lpr_filter = gr.fir_filter_fff(audio_decim, lpr_filter_coeffs)
pilot_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
sdr_rate, # sampling rate
19e3-500, # low cutoff
19e3+500, # high cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.pilot_filter = gr.fir_filter_fff(1, pilot_filter_coeffs)
dsbsc_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
sdr_rate, # sampling rate
38e3-15e3/2, # low cutoff
38e3+15e3/2, # high cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.dsbsc_filter = gr.fir_filter_fff(1, dsbsc_filter_coeffs)
rds_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
sdr_rate, # sampling rate
57e3-3e3, # low cutoff
57e3+3e3, # high cutoff
3e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_filter = gr.fir_filter_fff(1, rds_filter_coeffs)
# print "# lpr filter:", len(lpr_filter_coeffs), "taps"
# print "# pilot filter:", len(pilot_filter_coeffs), "taps"
# print "# dsbsc filter:", len(dsbsc_filter_coeffs), "taps"
# print "# rds filter:", len(rds_filter_coeffs), "taps"
self.connect(self.fm_demod, self.lpr_filter)
self.connect(self.fm_demod, self.pilot_filter)
self.connect(self.fm_demod, self.dsbsc_filter)
self.connect(self.fm_demod, self.rds_filter)
# down-convert L-R, RDS
self.stereo_baseband = gr.multiply_ff()
self.connect(self.pilot_filter, (self.stereo_baseband, 0))
self.connect(self.pilot_filter, (self.stereo_baseband, 1))
self.connect(self.dsbsc_filter, (self.stereo_baseband, 2))
self.rds_baseband = gr.multiply_ff()
self.connect(self.pilot_filter, (self.rds_baseband, 0))
self.connect(self.pilot_filter, (self.rds_baseband, 1))
self.connect(self.pilot_filter, (self.rds_baseband, 2))
self.connect(self.rds_filter, (self.rds_baseband, 3))
# low-pass and downsample L-R
lmr_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
sdr_rate, # sampling rate
15e3, # passband cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.lmr_filter = gr.fir_filter_fff(audio_decim, lmr_filter_coeffs)
self.connect(self.stereo_baseband, self.lmr_filter)
# create L, R from L-R, L+R
self.left = gr.add_ff()
self.right = gr.sub_ff()
self.connect(self.lpr_filter, (self.left, 0))
self.connect(self.lmr_filter, (self.left, 1))
self.connect(self.lpr_filter, (self.right, 0))
self.connect(self.lmr_filter, (self.right, 1))
# volume control, complex2flot, audio sink
self.volume_control_l = gr.multiply_const_ff(self.vol)
self.volume_control_r = gr.multiply_const_ff(self.vol)
output_audio_rate = 48000
self.resamp_L = blks2.rational_resampler_fff(interpolation=output_audio_rate,decimation=audio_rate,taps=None,fractional_bw=None,)
self.resamp_R = blks2.rational_resampler_fff(interpolation=output_audio_rate,decimation=audio_rate,taps=None,fractional_bw=None,)
self.connect(self.left, self.volume_control_l, self.resamp_L)
self.connect(self.right, self.volume_control_r, self.resamp_R)
# self.audio_sink = audio.sink(int(output_audio_rate),
# options.audio_output, False)
# self.connect(self.resamp_L, (self.audio_sink, 0))
# self.connect(self.resamp_R, (self.audio_sink, 1))
self.file_sink1 = gr.file_sink(gr.sizeof_float, 'audioL.dat')
self.file_sink2 = gr.file_sink(gr.sizeof_float, 'audioR.dat')
self.file_sink3 = gr.file_sink(gr.sizeof_float, 'fmDemod.dat')
self.connect(self.resamp_L, self.file_sink1)
self.connect(self.resamp_R, self.file_sink2)
self.connect(self.fm_demod, self.file_sink3)
# low-pass the baseband RDS signal at 1.5kHz
rds_bb_filter_coeffs = gr.firdes.low_pass(
1, # gain
sdr_rate, # sampling rate
1.5e3, # passband cutoff
2e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_bb_filter = gr.fir_filter_fff(audio_decim, rds_bb_filter_coeffs)
# print "# rds bb filter:", len(rds_bb_filter_coeffs), "taps"
self.connect(self.rds_baseband, self.rds_bb_filter)
# 1187.5bps = 19kHz/16
self.clock_divider = rds.freq_divider(16)
rds_clock_taps = gr.firdes.low_pass(
1, # gain
sdr_rate, # sampling rate
1.2e3, # passband cutoff
1.5e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_clock = gr.fir_filter_fff(audio_decim, rds_clock_taps)
# print "# rds clock filter:", len(rds_clock_taps), "taps"
self.connect(self.pilot_filter, self.clock_divider, self.rds_clock)
# bpsk_demod, diff_decoder, rds_decoder
self.bpsk_demod = rds.bpsk_demod(audio_rate)
self.differential_decoder = gr.diff_decoder_bb(2)
self.msgq = gr.msg_queue()
self.rds_decoder = rds.data_decoder(self.msgq)
self.connect(self.rds_bb_filter, (self.bpsk_demod, 0))
self.connect(self.rds_clock, (self.bpsk_demod, 1))
self.connect(self.bpsk_demod, self.differential_decoder)
self.connect(self.differential_decoder, self.rds_decoder)
def __init__(self):
gr.top_block.__init__ (self)
parser=OptionParser(option_class=eng_option)
parser.add_option("-H", "--hostname", type="string", default="localhost",
help="set hostname of generic sdr")
parser.add_option("-P", "--portnum", type="int", default=None,
help="set portnum of generic sdr")
parser.add_option("-W", "--wsportnum", type="int", default=None,
help="set portnum of audio websocket server")
parser.add_option("-r", "--sdr_rate", type="eng_float", default=250e3,
help="set sample rate of generic sdr")
parser.add_option("-V", "--volume", type="eng_float", default=None,
help="set volume (default is midpoint)")
parser.add_option("-O", "--audio-output", type="string", default="plughw:0,0",
help="pcm device name (default is plughw:0,0)")
# print help when called with wrong arguments
(options, args) = parser.parse_args()
if len(args) != 0:
parser.print_help()
sys.exit(1)
self.vol = options.volume
if self.vol is None:
self.vol = 0.1
# connect to generic SDR
sdr_rate = options.sdr_rate
audio_decim = 8
audio_rate = int(sdr_rate/audio_decim)
print "audio_rate = ", audio_rate
self.interleaved_short_to_complex = gr.interleaved_short_to_complex()
self.char_to_short = gr.char_to_short(1)
self.sdr_source = grc_blks2.tcp_source(
itemsize=gr.sizeof_char*1,
addr=options.hostname,
port=options.portnum,
server=False
)
# self.sdr_source = gr.file_source(1, 'sdrs_baseband.dat')
# self.throttle = gr.throttle(1, 500e3)
# self.connect(self.sdr_source, self.file_sink)
self.logger = gr.file_sink(1, 'log.out')
self.connect(self.sdr_source, self.logger)
# channel filter
chan_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
sdr_rate, # sampling rate
80e3, # passband cutoff
35e3, # transition width
gr.firdes.WIN_HAMMING)
self.chan_filter = gr.fir_filter_ccf(1, chan_filter_coeffs)
# print "# channel filter:", len(chan_filter_coeffs), "taps"
# PLL-based WFM demod
fm_alpha = 0.25 * 250e3 * math.pi / sdr_rate # 0.767
fm_beta = fm_alpha * fm_alpha / 4.0 # 0.147
fm_max_freq = 2.0 * math.pi * 90e3 / sdr_rate # 2.209
self.fm_demod = gr.pll_freqdet_cf(
1.0, # Loop BW
fm_max_freq, # in radians/sample
-fm_max_freq)
self.fm_demod.set_alpha(fm_alpha)
self.fm_demod.set_beta(fm_beta)
self.connect(self.sdr_source, self.char_to_short)
self.connect(self.char_to_short, self.interleaved_short_to_complex)
self.connect(self.interleaved_short_to_complex, self.chan_filter, self.fm_demod)
# L+R, pilot, L-R, RDS filters
lpr_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
sdr_rate, # sampling rate
15e3, # passband cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.lpr_filter = gr.fir_filter_fff(audio_decim, lpr_filter_coeffs)
pilot_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
sdr_rate, # sampling rate
19e3-500, # low cutoff
19e3+500, # high cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.pilot_filter = gr.fir_filter_fff(1, pilot_filter_coeffs)
dsbsc_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
sdr_rate, # sampling rate
38e3-15e3/2, # low cutoff
38e3+15e3/2, # high cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.dsbsc_filter = gr.fir_filter_fff(1, dsbsc_filter_coeffs)
rds_filter_coeffs = gr.firdes.band_pass(
1.0, # gain
sdr_rate, # sampling rate
57e3-3e3, # low cutoff
57e3+3e3, # high cutoff
3e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_filter = gr.fir_filter_fff(1, rds_filter_coeffs)
# print "# lpr filter:", len(lpr_filter_coeffs), "taps"
# print "# pilot filter:", len(pilot_filter_coeffs), "taps"
# print "# dsbsc filter:", len(dsbsc_filter_coeffs), "taps"
# print "# rds filter:", len(rds_filter_coeffs), "taps"
self.connect(self.fm_demod, self.lpr_filter)
self.connect(self.fm_demod, self.pilot_filter)
self.connect(self.fm_demod, self.dsbsc_filter)
self.connect(self.fm_demod, self.rds_filter)
# down-convert L-R, RDS
self.stereo_baseband = gr.multiply_ff()
self.connect(self.pilot_filter, (self.stereo_baseband, 0))
self.connect(self.pilot_filter, (self.stereo_baseband, 1))
self.connect(self.dsbsc_filter, (self.stereo_baseband, 2))
self.rds_baseband = gr.multiply_ff()
self.connect(self.pilot_filter, (self.rds_baseband, 0))
self.connect(self.pilot_filter, (self.rds_baseband, 1))
self.connect(self.pilot_filter, (self.rds_baseband, 2))
self.connect(self.rds_filter, (self.rds_baseband, 3))
# low-pass and downsample L-R
lmr_filter_coeffs = gr.firdes.low_pass(
1.0, # gain
sdr_rate, # sampling rate
15e3, # passband cutoff
1e3, # transition width
gr.firdes.WIN_HAMMING)
self.lmr_filter = gr.fir_filter_fff(audio_decim, lmr_filter_coeffs)
self.connect(self.stereo_baseband, self.lmr_filter)
# create L, R from L-R, L+R
self.left = gr.add_ff()
self.right = gr.sub_ff()
self.connect(self.lpr_filter, (self.left, 0))
self.connect(self.lmr_filter, (self.left, 1))
self.connect(self.lpr_filter, (self.right, 0))
self.connect(self.lmr_filter, (self.right, 1))
# volume control, complex2flot, audio sink
self.volume_control_l = gr.multiply_const_ff(self.vol)
self.volume_control_r = gr.multiply_const_ff(self.vol)
output_audio_rate = 48000
self.resamp_L = blks2.rational_resampler_fff(interpolation=output_audio_rate,decimation=audio_rate,taps=None,fractional_bw=None,)
self.resamp_R = blks2.rational_resampler_fff(interpolation=output_audio_rate,decimation=audio_rate,taps=None,fractional_bw=None,)
self.connect(self.left, self.volume_control_l, self.resamp_L)
self.connect(self.right, self.volume_control_r, self.resamp_R)
# self.audio_sink = audio.sink(int(output_audio_rate),
# options.audio_output, False)
# self.connect(self.resamp_L, (self.audio_sink, 0))
# self.connect(self.resamp_R, (self.audio_sink, 1))
# self.file_sink1 = gr.file_sink(gr.sizeof_float, 'audioL.dat')
# self.file_sink2 = gr.file_sink(gr.sizeof_float, 'audioR.dat')
# self.file_sink3 = gr.file_sink(gr.sizeof_float, 'fmDemod.dat')
# self.connect(self.resamp_L, self.file_sink1)
# self.connect(self.resamp_R, self.file_sink2)
# self.connect(self.fm_demod, self.file_sink3)
# Interleave both channels so that we can push over one websocket connection
self.audio_interleaver = gr.float_to_complex(1)
self.connect(self.resamp_L, (self.audio_interleaver, 0))
self.connect(self.resamp_R, (self.audio_interleaver, 1))
self.ws_audio_server = sdrportal.ws_sink_c(True, options.wsportnum, "FLOAT")
self.connect(self.audio_interleaver, self.ws_audio_server)
# low-pass the baseband RDS signal at 1.5kHz
rds_bb_filter_coeffs = gr.firdes.low_pass(
1, # gain
sdr_rate, # sampling rate
1.5e3, # passband cutoff
2e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_bb_filter = gr.fir_filter_fff(audio_decim, rds_bb_filter_coeffs)
# print "# rds bb filter:", len(rds_bb_filter_coeffs), "taps"
self.connect(self.rds_baseband, self.rds_bb_filter)
# 1187.5bps = 19kHz/16
self.clock_divider = rds.freq_divider(16)
rds_clock_taps = gr.firdes.low_pass(
1, # gain
sdr_rate, # sampling rate
1.2e3, # passband cutoff
1.5e3, # transition width
gr.firdes.WIN_HAMMING)
self.rds_clock = gr.fir_filter_fff(audio_decim, rds_clock_taps)
# print "# rds clock filter:", len(rds_clock_taps), "taps"
self.connect(self.pilot_filter, self.clock_divider, self.rds_clock)
# bpsk_demod, diff_decoder, rds_decoder
self.bpsk_demod = rds.bpsk_demod(audio_rate)
self.differential_decoder = gr.diff_decoder_bb(2)
self.msgq = gr.msg_queue()
self.rds_decoder = rds.data_decoder(self.msgq)
self.connect(self.rds_bb_filter, (self.bpsk_demod, 0))
self.connect(self.rds_clock, (self.bpsk_demod, 1))
self.connect(self.bpsk_demod, self.differential_decoder)
self.connect(self.differential_decoder, self.rds_decoder)
def __init__(self, options):
gr.hier_block2.__init__(self, "ais_demod",
gr.io_signature(1, 1, gr.sizeof_gr_complex), # Input signature
gr.io_signature(1, 1, gr.sizeof_char)) # Output signature
self._samples_per_symbol = options.samples_per_symbol
self._bits_per_sec = options.bits_per_sec
self._samplerate = self._samples_per_symbol * self._bits_per_sec
self._gain_mu = options.gain_mu
self._mu = options.mu
self._omega_relative_limit = options.omega_relative_limit
self.fftlen = options.fftlen
#right now we are going to hardcode the different options for VA mode here. later on we can use configurable options
samples_per_symbol_viterbi = 2
bits_per_symbol = 2
samples_per_symbol = 6
samples_per_symbol_clockrec = samples_per_symbol / bits_per_symbol
BT = 0.4
data_rate = 9600.0
samp_rate = options.samp_rate
self.gmsk_sync = gmsk_sync.square_and_fft_sync(self._samplerate, self._bits_per_sec, self.fftlen)
if(options.viterbi is True):
#calculate the required decimation and interpolation to achieve the desired samples per symbol
denom = gcd(data_rate*samples_per_symbol, samp_rate)
cr_interp = int(data_rate*samples_per_symbol/denom)
cr_decim = int(samp_rate/denom)
self.resample = blks2.rational_resampler_ccc(cr_interp, cr_decim)
#here we take a different tack and use A.A.'s CPM decomposition technique
self.clockrec = gr.clock_recovery_mm_cc(samples_per_symbol_clockrec, 0.005*0.005*0.25, 0.5, 0.005, 0.0005) #might have to futz with the max. deviation
(fsm, constellation, MF, N, f0T) = make_gmsk(samples_per_symbol_viterbi, BT) #calculate the decomposition required for demodulation
self.costas = gr.costas_loop_cc(0.015, 0.015*0.015*0.25, 100e-6, -100e-6, 4) #does fine freq/phase synchronization. should probably calc the coeffs instead of hardcode them.
self.streams2stream = gr.streams_to_stream(int(gr.sizeof_gr_complex*1), int(N))
self.mf0 = gr.fir_filter_ccc(samples_per_symbol_viterbi, MF[0].conjugate()) #two matched filters for decomposition
self.mf1 = gr.fir_filter_ccc(samples_per_symbol_viterbi, MF[1].conjugate())
self.fo = gr.sig_source_c(samples_per_symbol_viterbi, gr.GR_COS_WAVE, -f0T, 1, 0) #the memoryless modulation component of the decomposition
self.fomult = gr.multiply_cc(1)
self.trellis = trellis.viterbi_combined_cb(fsm, int(data_rate), -1, -1, int(N), constellation, trellis.TRELLIS_EUCLIDEAN) #the actual Viterbi decoder
else:
#this is probably not optimal and someone who knows what they're doing should correct me
self.datafiltertaps = gr.firdes.root_raised_cosine(10, #gain
self._samplerate*32, #sample rate
self._bits_per_sec, #symbol rate
0.4, #alpha, same as BT?
50*32) #no. of taps
self.datafilter = gr.fir_filter_fff(1, self.datafiltertaps)
sensitivity = (math.pi / 2) / self._samples_per_symbol
self.demod = gr.quadrature_demod_cf(sensitivity) #param is gain
#self.clockrec = digital.clock_recovery_mm_ff(self._samples_per_symbol,0.25*self._gain_mu*self._gain_mu,self._mu,self._gain_mu,self._omega_relative_limit)
self.clockrec = gr.pfb_clock_sync_ccf(self._samples_per_symbol, 0.04, self.datafiltertaps, 32, 0, 1.15)
self.tcslicer = digital.digital.binary_slicer_fb()
# self.dfe = digital.digital.lms_dd_equalizer_cc(
# 32,
# 0.005,
# 1,
# digital.digital.constellation_bpsk()
# )
# self.delay = gr.delay(gr.sizeof_float, 64 + 16) #the correlator delays 64 bits, and the LMS delays some as well.
self.slicer = digital.digital.binary_slicer_fb()
# self.training_correlator = digital.correlate_access_code_bb("1100110011001100", 0)
# self.cma = digital.cma_equalizer_cc
#just a note here: a complex combined quad demod/slicer could be based on if's rather than an actual quad demod, right?
#in fact all the constellation decoders up to QPSK could operate on complex data w/o doing the whole atan thing
self.diff = gr.diff_decoder_bb(2)
self.invert = ais.invert() #NRZI signal diff decoded and inverted should give original signal
self.connect(self, self.gmsk_sync)
if(options.viterbi is False):
self.connect(self.gmsk_sync, self.clockrec, self.demod, self.slicer, self.diff, self.invert, self)
#self.connect(self.gmsk_sync, self.demod, self.clockrec, self.tcslicer, self.training_correlator)
#self.connect(self.clockrec, self.delay, (self.dfe, 0))
#self.connect(self.training_correlator, (self.dfe, 1))
#self.connect(self.dfe, self.slicer, self.diff, self.invert, self)
else:
self.connect(self.gmsk_sync, self.costas, self.resample, self.clockrec)
self.connect(self.clockrec, (self.fomult, 0))
self.connect(self.fo, (self.fomult, 1))
self.connect(self.fomult, self.mf0)
self.connect(self.fomult, self.mf1)
self.connect(self.mf0, (self.streams2stream, 0))
self.connect(self.mf1, (self.streams2stream, 1))
self.connect(self.streams2stream, self.trellis, self.diff, self.invert, self)
samplerate = 48000
src = audio.source(samplerate,"hw:1")
pluss = gr.add_const_ff(0.0)
lpcoeffs = gr.firdes.low_pass(1,samplerate,8000,3000)
lpfilter = gr.fir_filter_fff(1,lpcoeffs)
forsterk = gr.multiply_const_ff(5)
clockrec = gr.clock_recovery_mm_ff(float(samplerate)/9600,0.25*0.175*0.175,0.5,0.175,0.005)
slicer = gr.binary_slicer_fb()
# Parameters: ([mysql-server],[database name],[database user],[database password])
datadec = ais.ais_decoder_mysql("localhost","diverse","ruben","elg")
# You should use the create_mysql.sql to create the necessary tables
# in the database.
# See create_mysql.txt for help. Those files can be found in the root folder of
# the source tree.
diff = gr.diff_decoder_bb(2)
invert = ais.invert10_bb()
fg.connect(src,pluss,lpfilter,forsterk,clockrec,slicer,diff,invert,datadec)
fg.start()
raw_input("Receives AIS from soundcard ")
fg.stop()
print "Received correctly: ",datadec.received()
print "Wrong CRC: ",datadec.lost()
print "Wrong Size: ",datadec.lost2()
