def __init__(self, loginVo, sensorName):
logger.info('ProcessLedGreen init')
self.loginVo = loginVo
self.sensorName = sensorName
DAQC.clrLED(0, 0)
DAQC.clrLED(0, 1)
DAQC.enableSWint(0)
DAQC.intEnable(0)
self.ledColor = 'green'
self.btnPressed = '0'
def run(self, *args):
logger.info("ButtonPushedThread run start")
DAQC.enableSWint(self.daqcBoard)
DAQC.intEnable(self.daqcBoard)
while True:
if self.isShutdown:
break
if DAQC.getINTflags(self.daqcBoard) == 256:
self.pillDispenser.setDispenseState('CONFIRMING')
break
time.sleep(.25)
def leds():
DAQC.enableSWint(0)
DAQC.intEnable(0)
while True:
DAQC.setLED(0, 0)
if DAQC.getINTflags(0) == 256:
break
time.sleep(.25)
if DAQC.getINTflags(0) == 256:
break
DAQC.clrLED(0, 0)
if DAQC.getINTflags(0) == 256:
break
time.sleep(.25)
if DAQC.getINTflags(0) == 256:
break
for i in range(0, 100):
DAQC.clrLED(0, 0)
DAQC.clrLED(0, 1)
# ./rm_config.py
# Contains our config file utils
import rm_config
# ./rm_utils.py
# Contains various utility functions
import rm_utils
config = rm_config.rm_read_config()
# Interrupt setup
# NOTE: Not safe to run interupts with callbacks due to MySQL conflicts
GPIO.setup(22, GPIO.IN, pull_up_down=GPIO.PUD_UP)
GPIO.add_event_detect(22, GPIO.RISING, bouncetime=50)
DAQC.enableDINint(0, 0, 'r')
DAQC.intEnable(0)
# Globals
# These are set up in repeatermond.cfg
USER = config['MYSQLD']['USER']
PASSWD = config['MYSQLD']['PASSWD']
DBHOST = config['MYSQLD']['DBHOST']
DBNAME = config['MYSQLD']['DBNAME']
ANTS = [int(str_val) for str_val in config['MONITOR']['ANTS'].split(',')]
ANALOGIO = [
int(str_val) for str_val in config['MONITOR']['ANALOGIO'].split(',')
]
DIGIN = [int(str_val) for str_val in config['MONITOR']['DIGIN'].split(',')]
ELEMENTS = [
int(str_val) for str_val in config['MONITOR']['ELEMENTS'].split(',')
humidity = sensor.read_humidity()
t = sensor.t_fine
# measure from the (analog) photo-sensor
light = DAQC.getADC(0, 0)
global data
data.append([t, temp, pressure, humidity, light])
# turn off LEDs
DAQC.setDOUTall(0, 0)
# set up GPIO interface for pushbotton on PiDAQC
DAQC.enableSWint(0) # enable pushbutton interrupt
DAQC.intEnable(0) # enable global interrupts
DAQC.getINTflags(0) # clear any flags
# GPIO event detection must be set up AFTER clearing DAQC interrupt flag
GPIO.setmode(GPIO.BCM)
GPIO.setup(22, GPIO.IN, pull_up_down=GPIO.PUD_UP)
GPIO.add_event_detect(22, GPIO.FALLING, callback=sample)
DAQC.getINTflags(0)
# set up BME280
sensor = BME280(mode=BME280_OSAMPLE_8)
try:
while (1):
# wait for button
DAQC.setLED(0, 0)
counter1 += 1
if detector & 0b10:
counter2 += 1
def storecpm(value1, value2):
f = open("log.dat", 'a')
f.write(str(time.time()) + ",")
f.write(str(value1) + ",")
f.write( str(value2) + "\n")
f.close()
GPIO.setup(22, GPIO.IN, pull_up_down=GPIO.PUD_UP)
GPIO.add_event_detect(22, GPIO.FALLING, callback=counterDET)
DAQC.enableDINint(0,0,'r') #enable the push button interrupt
DAQC.enableDINint(0,1,'f')
DAQC.intEnable(0) #enable global interrupts
checkpoint = time.time()
try:
if (checkpoint < time.time()):
print "Counter is ", counter
storecpm(counter1, counter2)
counter1 = 0
counter2 = 0
checkpoint = time.time() + 60
except KeyboardInterrupt:
GPIO.cleanup()
