MAX_INTENTOS_LEER_DATOS = 20 # Número máximo de fallos seguidos permitidos al leer
# datos de un nodo.
# Definición lineas de entrada
IOLINE_IN_3 = IOLine.DIO3_AD3
IOLINE_IN_2 = IOLine.DIO2_AD2
IOLINE_IN_1 = IOLine.DIO1_AD1
IOLINE_IN_0 = IOLine.DIO0_AD0
# Tensión máxima en las entradas (mv)
MAX_VOLTAGE_INPUT = 1200
# Frecuencia de encuesta a los nodos en caso de que NO existan problemas (sg)
LONG_WAIT = 3 #30
# Frecuencia de encuesta a los nodos en caso de que SI existan problemas (sg)
SHORT_WAIT = 1
# Parámetros de conexión con el puerto serie al dispositivo local
port = read_sys_config.ReadLocalPortFromFile()
baud_rate = read_sys_config.ReadLocalBaudRateFromFile()
# Función para calcular el valor de temperatura medainte el valor crudo de la
# tensión de entrada y voltaje de alimentación (divisor de tensión)
def ntc10k_calculate_temp(raw_value, volts):
# mV
voltage = (MAX_VOLTAGE_INPUT * raw_value / 1024)
Rntc = 210000 * (voltage / (volts - voltage))
# AJUSTE_CUADRÁTICO (según curva calculada en Matlab)
a = 574.1
b = -0.1242
c = -158
temperatureC = a * (pow(Rntc, b)) + c
logging.debug('ntc 10K temper: %.2f', temperatureC)
def main():
#log=""
# Parámetros de conexión con el puerto serie al dispositivo local
port = read_sys_config.ReadLocalPortFromFile()
baud_rate = read_sys_config.ReadLocalBaudRateFromFile()
local_device = XBeeDevice(port, baud_rate)
try:
print(" +-----------------------------------------------+")
print(" | Get Local XBee Parameters |")
print(" +-----------------------------------------------+\n")
local_device.open()
# Get Hardware Models with extended DIO (P5 to P9)
Hardware_Extended = read_sys_config.ReadHardwareVersionWhithP5ToP9PinsFromFile()
# Get parameters.
# Diagnostic Commads
VR = utils.hex_to_string(local_device.get_parameter("VR"))
HV = utils.hex_to_string(local_device.get_parameter("HV"))
AI = utils.hex_to_string(local_device.get_parameter("AI"))
DB = utils.hex_to_string(local_device.get_parameter("DB"))
V = utils.hex_to_string(local_device.get_parameter("%V"))
# Networking
ID = utils.hex_to_string(local_device.get_parameter("ID"))
SC = utils.hex_to_string(local_device.get_parameter("SC"))
SD = utils.hex_to_string(local_device.get_parameter("SD"))
ZS = utils.hex_to_string(local_device.get_parameter("ZS"))
NJ = utils.hex_to_string(local_device.get_parameter("NJ"))
NW = utils.hex_to_string(local_device.get_parameter("NW"))
JV = utils.hex_to_string(local_device.get_parameter("JV"))
JN = utils.hex_to_string(local_device.get_parameter("JN"))
OP = utils.hex_to_string(local_device.get_parameter("OP"))
OI = utils.hex_to_string(local_device.get_parameter("OI"))
CH = utils.hex_to_string(local_device.get_parameter("CH"))
NC = utils.hex_to_string(local_device.get_parameter("NC"))
CE = utils.hex_to_string(local_device.get_parameter("CE"))
DO = utils.hex_to_string(local_device.get_parameter("DO"))
DC = utils.hex_to_string(local_device.get_parameter("DC"))
# Addressing
SH = utils.hex_to_string(local_device.get_parameter("SH"))
SL = utils.hex_to_string(local_device.get_parameter("SL"))
MY = utils.hex_to_string(local_device.get_parameter("MY"))
MP = utils.hex_to_string(local_device.get_parameter("MP"))
DH = utils.hex_to_string(local_device.get_parameter("DH"))
DL = utils.hex_to_string(local_device.get_parameter("DL"))
NI = local_device.get_parameter("NI").decode()
NH = utils.hex_to_string(local_device.get_parameter("NH"))
BH = utils.hex_to_string(local_device.get_parameter("BH"))
AR = utils.hex_to_string(local_device.get_parameter("AR"))
DD = utils.hex_to_string(local_device.get_parameter("DD"))
NT = utils.hex_to_string(local_device.get_parameter("NT"))
NO = utils.hex_to_string(local_device.get_parameter("NO"))
NP = utils.hex_to_string(local_device.get_parameter("NP"))
CR = utils.hex_to_string(local_device.get_parameter("CR"))
# ZigBee Addressing
SE = utils.hex_to_string(local_device.get_parameter("SE"))
DE = utils.hex_to_string(local_device.get_parameter("DE"))
CI = utils.hex_to_string(local_device.get_parameter("CI"))
TO = utils.hex_to_string(local_device.get_parameter("TO"))
# RF Interfacing
PL = utils.hex_to_string(local_device.get_parameter("PL"))
PM = utils.hex_to_string(local_device.get_parameter("PM"))
PP = utils.hex_to_string(local_device.get_parameter("PP"))
# Security
EE = utils.hex_to_string(local_device.get_parameter("EE"))
EO = utils.hex_to_string(local_device.get_parameter("EO"))
KY = utils.hex_to_string(local_device.get_parameter("KY"))
NK = utils.hex_to_string(local_device.get_parameter("NK"))
# Serial Interfacing
BD = utils.hex_to_string(local_device.get_parameter("BD"))
NB = utils.hex_to_string(local_device.get_parameter("NB"))
SB = utils.hex_to_string(local_device.get_parameter("SB"))
RO = utils.hex_to_string(local_device.get_parameter("RO"))
D6 = utils.hex_to_string(local_device.get_parameter("D6"))
D7 = utils.hex_to_string(local_device.get_parameter("D7"))
AP = utils.hex_to_string(local_device.get_parameter("AP"))
AO = utils.hex_to_string(local_device.get_parameter("AO"))
# AT Command Options
CT = utils.hex_to_string(local_device.get_parameter("CT"))
GT = utils.hex_to_string(local_device.get_parameter("GT"))
CC = utils.hex_to_string(local_device.get_parameter("CC"))
# Sleep Modes
SP = utils.hex_to_string(local_device.get_parameter("SP"))
SN = utils.hex_to_string(local_device.get_parameter("SN"))
SM = utils.hex_to_string(local_device.get_parameter("SM"))
ST = utils.hex_to_string(local_device.get_parameter("ST"))
SO = utils.hex_to_string(local_device.get_parameter("SO"))
WH = utils.hex_to_string(local_device.get_parameter("WH"))
PO = utils.hex_to_string(local_device.get_parameter("PO"))
# I/O Settomgs
D0 = utils.hex_to_string(local_device.get_parameter("D0"))
D1 = utils.hex_to_string(local_device.get_parameter("D1"))
D2 = utils.hex_to_string(local_device.get_parameter("D2"))
D3 = utils.hex_to_string(local_device.get_parameter("D3"))
D4 = utils.hex_to_string(local_device.get_parameter("D4"))
D5 = utils.hex_to_string(local_device.get_parameter("D5"))
D8 = utils.hex_to_string(local_device.get_parameter("D8"))
D9 = utils.hex_to_string(local_device.get_parameter("D9"))
P0 = utils.hex_to_string(local_device.get_parameter("P0"))
P1 = utils.hex_to_string(local_device.get_parameter("P1"))
P2 = utils.hex_to_string(local_device.get_parameter("P2"))
P3 = utils.hex_to_string(local_device.get_parameter("P3"))
P4 = utils.hex_to_string(local_device.get_parameter("P4"))
if HV == Hardware_Extended:
P5 = utils.hex_to_string(local_device.get_parameter("P5"))
P6 = utils.hex_to_string(local_device.get_parameter("P6"))
P7 = utils.hex_to_string(local_device.get_parameter("P7"))
P8 = utils.hex_to_string(local_device.get_parameter("P8"))
P9 = utils.hex_to_string(local_device.get_parameter("P9"))
PR = utils.hex_to_string(local_device.get_parameter("PR"))
PD = utils.hex_to_string(local_device.get_parameter("PD"))
LT = utils.hex_to_string(local_device.get_parameter("LT"))
RP = utils.hex_to_string(local_device.get_parameter("RP"))
# I/O Sampling
IR = utils.hex_to_string(local_device.get_parameter("IR"))
IC = utils.hex_to_string(local_device.get_parameter("IC"))
Vplus = utils.hex_to_string(local_device.get_parameter("V+"))
#print parameters
log= " +-----------------------------+\n"
log= log + " | Networking |\n"
log = log + " +-----------------------------+\n"
log = log + " PAN ID: %s" % ID + "\n"
log = log + " Scan Channel: %s" % SC + "\n"
log = log + " Scan Duration: %s" % SD + "\n"
log = log + " Network Watchdog Timeout: %s" % NW + "\n"
log = log + " Channel Verification: %s" % JV + "\n"
log = log + " Join Notification: %s" % JN + "\n"
log = log + " Operating PAN ID: %s" % OP + "\n"
log = log + " Operating 16-bit PAN ID: %s" % OI + "\n"
log = log + " Operating Channel: %s" % CH + "\n"
log = log + " Number of Remaining Children:%s" % NC + "\n"
log = log + " Coordinator Enable: %s" % CE + "\n"
log = log + " Device Options: %s" % DO + "\n"
log = log + " Device Controls: %s" % DC + "\n\n"
log = log + " +-----------------------------+\n"
log = log + " | Addressing |\n"
log = log + " +-----------------------------+\n"
log = log + " Serial Number High: %s" % SH + "\n"
log = log + " Serial Number Low: %s" % SL + "\n"
log = log + " 16-bit Network Address: %s" % MY + "\n"
log = log + " 16-bit Parent Address: %s" % MP + "\n"
log = log + " Destination Address High: %s" % DH + "\n"
log = log + " Destination Address Low: %s" % DL + "\n"
log = log + " Node Identifier: %s" % NI + "\n"
log = log + " Maximum Hops: %s" % NH + "\n"
log = log + " Broadcast Radius: %s" % BH + "\n"
log = log + " Many-to-One Route Bro. Time: %s" % AR + "\n"
log = log + " Device Type Identifier: %s" % DD + "\n"
log = log + " Node Discovery Backoff: %s" % NT + "\n"
log = log + " Node Discovery Options: %s" % NO + "\n"
log = log + " Maximum Num.Trans. Bytes: %s" % NP + "\n"
log = log + " PAN Conflict Threshold: %s" % CR + "\n\n"
log = log + " +-----------------------------+\n"
log = log + " | ZigBee Addressing |\n"
log = log + " +-----------------------------+\n"
log = log + " Zigbee Source Endpoint: %s" % SE + "\n"
log = log + " Zigbee Destination Endpoint: %s" % DE + "\n"
log = log + " Zigbee Cluster ID: %s" % CI + "\n"
log = log + " Transmit Options: %s" % TO + "\n\n"
log = log + " +-----------------------------+\n"
log = log + " | RF Interfacing |\n"
log = log + " +-----------------------------+\n"
log = log + " Tx Power Level: %s" % PL + "\n"
log = log + " Power Mode: %s" % PM + "\n"
log = log + " Power at PL4: %s" % PP + "\n\n"
log = log + " +-----------------------------+\n"
log = log + " | Security |\n"
log = log + " +-----------------------------+\n"
log = log + " Encryption Enable: %s" % EE + "\n"
log = log + " Encryption Options: %s" % EO + "\n"
log = log + " Encryption Key: %s" % KY + "\n"
log = log + " Network Encryption Key: %s" % NK + "\n\n"
log = log + " +-----------------------------+\n"
log = log + " | Serial Interfacing |\n"
log = log + " +-----------------------------+\n"
log = log + " Baud Rate: %s" % BD + "\n"
log = log + " Parity: %s" % NB + "\n"
log = log + " Stop Bits: %s" % SB + "\n"
log = log + " Packetization Timeout: %s" % RO + "\n"
log = log + " DIO6/nRTS Configuration : %s" % D6 + "\n"
log = log + " DIO7/nCTS Configuration: %s" % D7 + "\n"
log = log + " API Enable: %s" % AP + "\n"
log = log + " API Output Mode: %s" % AO + "\n\n"
log = log + " +-----------------------------+\n"
log = log + " | AT Command Options |\n"
log = log + " +-----------------------------+\n"
log = log + " AT Command Mode Timeout: %s" % CT + "\n"
log = log + " Guard Times: %s" % GT + "\n"
log = log + " Command Sequence Character: %s" % CC + "\n\n"
log = log + " +-----------------------------+\n"
log = log + " | Sleep Modes |\n"
log = log + " +-----------------------------+\n"
log = log + " Cyclic Sleep Period: %s" % SP + "\n"
log = log + " Number of Cyclic Sleep Per.: %s" % SN + "\n"
log = log + " Sleep Mode: %s" % SM + "\n"
log = log + " Time Before Sleep:sss %s" % ST + "\n"
log = log + " Sleep Options: %s" % SO + "\n"
log = log + " Wake Hosts: %s" % WH + "\n"
log = log + " Poll Rate: %s" % PO + "\n\n"
log = log + " +-----------------------------+\n"
log = log + " | I/O Settings |\n"
log = log + " +-----------------------------+\n"
log = log + " DIO0/ADO/CB Configuration: %s" % D0 + "\n"
log = log + " DIO1/AD1 Configuration: %s" % D1 + "\n"
log = log + " DIO2/AD2 Configuration: %s" % D2 + "\n"
log = log + " DIO3/AD3 Configuration: %s" % D3 + "\n"
log = log + " DIO4 Configuration: %s" % D4 + "\n"
log = log + " DIO5 Configuration: %s" % D5 + "\n"
log = log + " DIO8 Configuration: %s" % D8 + "\n"
log = log + " DIO9 Configuration: %s" % D9 + "\n"
log = log + " DIO10 Configuration: %s" % P0 + "\n"
log = log + " DIO11 Configuration: %s" % P1 + "\n"
log = log + " DIO12 Configuration: %s" % P2 + "\n"
log = log + " DIO13 Configuration: %s" % P3 + "\n"
log = log + " DIO14 Configuration: %s" % P4 + "\n"
if HV == Hardware_Extended:
log = log + " DIO15 Configuration: %s" % P5 + "\n"
log = log + " DIO16 Configuration: %s" % P6 + "\n"
log = log + " DIO17 Configuration: %s" % P7 + "\n"
log = log + " DIO18 Configuration: %s" % P8 + "\n"
log = log + " DIO19 Configuration: %s" % P9 + "\n"
log = log + " Pull-UP Resistor Enable: %s" % PR + "\n"
log = log + " Pull-Up/down Direction: %s" % PD + "\n"
log = log + " Associate LED Blink Time: %s" % LT + "\n"
log = log + " RSSI PWM Timer: %s" % RP + "\n\n"
log = log + " +-----------------------------+\n"
log = log + " | I/O Sampling |\n"
log = log + " +-----------------------------+\n"
log = log + " IO Sampling Rate: %s" % IR + "\n"
log = log + " Digital IO Change Detection: %s" % IC + "\n"
log = log + " Supply Votage High Thres.: %s" % Vplus + "\n\n"
log = log + " +-----------------------------+\n"
log = log + " | Diagnostic Commands |\n"
log = log + " +-----------------------------+\n"
log = log + " Firmaware Version: %s" % VR + "\n"
log = log + " Hardware Version: %s" % HV + "\n"
log = log + " Association Indication: %s" % AI + "\n"
log = log + " RSSI of Last Packet: %s" % DB + "\n"
except:
if local_device.is_open():
local_device.close()
log ="Sorry an error has happened"
pass
finally:
if local_device is not None and local_device.is_open():
local_device.close()
pass
return log