def __init__(self, name, sda=None, scl=None,
width=128, height=64,
addr=0x3c):
self.present = False
self._y = 0
self._x = 0
self.last_text = ""
self.char_width = width // 8
self.char_height = height // 8
if type(sda) is I2C:
i2c = sda
else:
i2c = I2C(sda=sda, scl=scl)
# test if lcd is responding
try:
self.dp = ssd1306.SSD1306_I2C(width, height, i2c, addr=addr)
self.clear(show=False)
self.println(" iot.ulno.net\n", show=True)
except OSError:
print("lcd not found")
else:
self.present = True
Device.__init__(self, name, i2c, setters={"set": self.evaluate},
report_change=False)
self.getters[""] = self.value
def __init__(self,
name,
pin,
ignore_case=True,
on_change=None,
report_change=False,
turn_time_ms=700,
freq=50,
min_us=600,
max_us=2400,
angle=180):
self.min_us = min_us
self.max_us = max_us
self.us = 0
self.freq = freq
self.angle = angle
self.angle_list = None
self.turn_time_ms = turn_time_ms
self.turn_start = None
Device.__init__(self,
name,
PWM(pin, freq=self.freq, duty=0),
setters={"set": self.turn},
ignore_case=ignore_case,
on_change=on_change,
report_change=report_change)
self._init()
def __init__(self,
name,
pin,
ignore_case=True,
on_change=None,
report_change=False):
self.is_on = False
self.last_rgb = _c.white
self.current_rgb = _c.black
self.ani = None
b = "brightness"
r = "rgb"
s = "set"
st = "/status"
Device.__init__(self,
name,
pin,
setters={
b + "/" + s: self._command_brightness,
r + "/" + s: self._command_rgb,
s: self._command_status,
"animation": self.animation
},
getters={
"": self.get_status,
b + st: self.get_brightness,
r + st: self.get
},
ignore_case=ignore_case,
on_change=on_change,
report_change=report_change)
self.set(*_c.black) # off
def __init__(self,
name,
trigger_pin,
echo_pin,
echo_timeout_us=30000,
precision=10,
on_change=None,
report_change=True,
filter=None):
# trigger_pin: Output pin to send pulses
# echo_pin: Readonly pin to measure the distance.
# The pin should be protected with 1k resistor
# echo_timeout_us: Timeout in microseconds to listen to echo pin.
# By default is based in sensor limit range (4m)
self.current_value = 0
self._last_measured = 0
if type(trigger_pin) is not Pin:
trigger_pin = Pin(trigger_pin)
self.trigger_pin = trigger_pin
if type(echo_pin) is not Pin:
echo_pin = Pin(trigger_pin)
self.echo_pin = echo_pin
self.precision = precision
trigger_pin.init(Pin.OUT)
trigger_pin.off()
echo_pin.init(Pin.IN)
echo_pin.init(Pin.OPEN_DRAIN)
self.echo_timeout_us = echo_timeout_us
self.distance = None
Device.__init__(self,
name, (trigger_pin, echo_pin),
on_change=on_change,
report_change=report_change,
filter=filter)
def __init__(self, name, sda=None, scl=None,
addr=8, ignore_case=False, report_change=True, filter=None):
not_found = "i2c device not found"
self.addr = addr
self.ownaddr = addr
self.count = None
self.current_value = ""
self.suspend_start = None
self.suspend_time = 0
self.msgq = None
if type(sda) is I2C:
i2c = sda
else:
i2c = I2C(sda=sda, scl=scl)
try:
l = i2c.scan() # see, if you can find the dive with respective addr
except OSError:
print(not_found)
else:
if addr in l:
self.present = True
Device.__init__(self, name, i2c, setters={"set": self.evaluate},
ignore_case=ignore_case,
report_change=report_change, filter=filter)
else:
print(not_found)
def __init__(self,
name,
pin,
*args,
report_high="on",
report_low="off",
pullup=True,
threshold=0,
on_change=None,
report_change=True,
filter=None):
if len(args) > 0:
report_high = args[0]
if len(args) > 1:
report_low = args[1]
Device.__init__(self,
name,
pin,
value_map={
True: report_high,
False: report_low
},
on_change=on_change,
report_change=report_change,
filter=filter)
if pullup:
pin.init(Pin.IN, Pin.PULL_UP)
else:
pin.init(Pin.IN)
try:
Pin.init(Pin.OPEN_DRAIN)
except:
pass
self.threshold = threshold + 1
self.debouncer = self.port() * self.threshold
def __init__(self,
name,
pin,
rising=False,
falling=False,
pullup=True,
on_change=None,
report_change=True):
if pullup:
pin.init(Pin.IN, Pin.PULL_UP)
else:
pin.init(Pin.IN, Pin.OPEN_DRAIN)
if rising and falling:
trigger = Pin.IRQ_RISING | Pin.IRQ_FALLING
elif not rising and falling:
trigger = Pin.IRQ_FALLING
else: # also if both all false
trigger = Pin.IRQ_RISING
pin.irq(trigger=trigger, handler=self.callback)
self.counter = 0
self.report_counter = 0
self.triggered = False
Device.__init__(self,
name,
pin,
on_change=on_change,
report_change=report_change)
self.getters[""] = self.value
def __init__(self,
name,
pin,
*args,
high_command='on',
low_command='off',
ignore_case=True,
on_change=None,
report_change=False):
if len(args) > 0:
high_command = args[0]
if len(args) > 1:
low_command = args[1]
if ignore_case:
high_command = high_command.lower()
low_command = low_command.lower()
self.high_command = high_command
self.low_command = low_command
Device.__init__(self,
name,
pin,
setters={"set": self.evaluate},
ignore_case=ignore_case,
on_change=on_change,
report_change=report_change,
value_map={
1: self.high_command,
0: self.low_command
})
pin.init(Pin.OUT)
self.state = pin()
def __init__(self, name, pin, on_change=None, filter=None):
import onewire, ds18x20
gc.collect()
self.ds = ds18x20.DS18X20(onewire.OneWire(pin))
self.roms = self.ds.scan()
self.lasttime = time.ticks_ms()
self.ds.convert_temp()
self.temp_list = None
Device.__init__(self, name, pin, on_change=on_change, filter=filter)
def __init__(self, name, precision=1, threshold=None,
on_change=None, report_change=True):
self.precision = precision
self.threshold = None
if threshold is not None:
self.threshold = max(1, min(threshold, 1023))
self.current_value = -10000
Device.__init__(self, name, ADC(0), on_change=on_change,
report_change=report_change)
self.getters[""] = self.value
def __init__(self, name, pin, dht_dev, delay,
on_change=None, report_change=True):
self.delay = delay
import dht
self.dht = dht_dev
self.lasttime = time.ticks_ms()
self.dht.measure()
Device.__init__(self, name, pin, on_change=on_change,
getters={"temperature": self.temperature,
"humidity": self.humidity},
report_change=report_change)
def __init__(self,
name,
precision=1,
threshold=None,
on_change=None,
report_change=True,
filter=None):
self.precision = precision
self.threshold = None
if threshold is not None:
self.threshold = max(1, min(threshold, 1023))
self.last_value = None
Device.__init__(self,
name,
ADC(0),
on_change=on_change,
report_change=report_change,
filter=filter)
def __init__(self,
name,
sda=None,
scl=None,
width=16,
height=2,
addr=0x27):
self.present = False
self.last_text = ""
self.char_width = width
self.char_height = height
self.display_buffer = bytearray(b" " * width * height)
self.back_buffer = bytearray(b" " * width * height)
self.x = 0
self.y = 0
if type(sda) is I2C:
i2c = sda
else:
i2c = I2C(sda=sda, scl=scl)
# test if lcd is responding
try:
self.dp = I2cLcd(i2c, addr, height, width)
self.dp.clear()
self.clear()
self.hide_cursor()
self.println("iot.ulno.net")
except OSError:
print("lcd not found")
else:
self.present = True
Device.__init__(self,
name,
i2c,
setters={"set": self.evaluate},
report_change=False)
self.getters[""] = self.value
def __init__(self,
name,
pin,
freq=50,
duty=0,
ignore_case=True,
on_change=None,
report_change=False):
self._duty = 0
self._freq = freq
Device.__init__(self,
name,
machine.PWM(pin, freq=freq, duty=duty),
setters={
"freq/set": self.set_freq,
"duty/set": self.set_duty
},
getters={
"freq": self.get_freq,
"duty": self.get_duty
},
ignore_case=ignore_case,
on_change=on_change,
report_change=report_change)
def __init__(self,
name,
rst,
cs=None,
sck=None,
mosi=None,
miso=None,
key=b'\xff\xff\xff\xff\xff\xff',
datasize=128,
on_change=None,
report_change=True,
filter=None):
rst.init(Pin.OUT)
self.rst = rst
if self.rst is not None:
self.rst.value(0)
self.datasize = datasize
self.key = key
board = uname()[0]
if sck is None: # select defaults (hw based spi)
if board == 'WiPy' or board == 'LoPy' or board == 'FiPy':
spi = SPI(0)
spi.init(SPI.MASTER, baudrate=1000000, pins=(14, 13, 12))
elif board == 'esp8266':
spi = SPI(1, baudrate=2500000, polarity=0, phase=0)
spi.init()
# hw uses the following pins
# sck = Pin(14,Pin.OUT) # d5 (ck)
# mosi = Pin(13,Pin.OUT) # d7 (mo)
# miso = Pin(12,Pin.IN) # d6 (mi)
else:
raise RuntimeError("Unsupported platform")
# TODO: does it make sense to set cs here to default?
if cs is None:
self.cs = Pin(15, Pin.OUT) # d8 (cs)
else:
self.cs = cs
cs.init(Pin.OUT)
self.spi = spi
else:
self.cs = cs
if cs is not None:
cs.init(Pin.OUT)
if type(sck) is SPI:
self.spi = sck
else:
if board == 'WiPy' or board == 'LoPy' or board == 'FiPy':
spi = SPI(0)
spi.init(SPI.MASTER,
baudrate=1000000,
pins=(sck, mosi, miso))
elif board == 'esp8266':
sck.init(Pin.OUT)
mosi.init(Pin.OUT)
miso.init(Pin.IN)
spi = SPI(baudrate=100000,
polarity=0,
phase=0,
sck=sck,
mosi=mosi,
miso=miso)
spi.init()
else:
raise RuntimeError("Unsupported platform")
self.spi = spi
if self.rst is not None:
self.rst.value(1)
if self.cs is not None:
self.cs.value(0)
# get some memory
self.reg_buf = bytearray(4)
self.block_write_buf = bytearray(18)
self.auth_buf = bytearray(12)
self.wreg_buf = bytearray(2)
self.rreg_buf = bytearray(1)
self.recv_buf = bytearray(16)
self.recv_mv = memoryview(self.recv_buf)
self.maxdata = datasize
self.card_data_buf = bytearray(16)
self.phys_init()
self.last_access = time.ticks_ms()
self.access_interval = 500 # only allow reads every 500ms
Device.__init__(self,
name,
spi,
on_change=on_change,
report_change=report_change,
filter=filter)