def APDS9960_ReadMulti(ser, reg, count):
strx = "i2c write 1,0x39," + hex(reg & 0xFF) + "\r\n"
usb2io_sendcmd(ser, strx, 1)
strx = "i2c read 1,0x39," + str(count) + "\r\n"
rrd = usb2io_sendcmd(ser, strx, 1)
ba1 = [int(i, 16) for i in rrd.replace('OK,', '').split(',')]
return (ba1)
def APDS9960_RdByte(ser, reg):
strx = "i2c write 1,0x39," + hex(reg & 0xFF) + "\r\n"
usb2io_sendcmd(ser, strx, 1)
strx = "i2c read 1,0x39,1\r\n"
rrd = usb2io_sendcmd(ser, strx, 1)
if (rrd.find("OK,", 0, 3) != -1):
bytes_str = rrd[3:]
return (True, int(bytes_str, 16))
return (False, 0)
def APDS9960_RdDWord(ser, reg):
strx = "i2c write 1,0x39," + hex(reg & 0xFF) + "\r\n"
rrd = usb2io_sendcmd(ser, strx, 1)
strx = "i2c read 1,0x39,4\r\n"
rrd = usb2io_sendcmd(ser, strx, 1)
if (rrd.find('FAIL') != -1):
return (False, 0)
ba1 = [int(i, 16) for i in rrd.replace('OK,', '').split(',')]
dwval = (ba1[0] << 24) | (ba1[1] << 16) | (ba1[2] << 8) | ba1[3]
return (True, dwval)
def readRegister(self, addr):
# first set address
if (usb2io_sendcmd(
self.ser, "i2c write 1, " + str(AS7265X_ADDR) + ", " +
str(addr) + "\r\n", 1) != "OK\r\n"):
return False, 0
rrd = usb2io_sendcmd(self.ser,
"i2c read 1, " + str(AS7265X_ADDR) + ", 1\r\n", 1)
if (rrd.find("OK,", 0, 3) != -1):
# parse result
bytes_str = rrd[3:]
return True, int(bytes_str, 16)
return False, 0
print "===================================="
print "* AK4954 Config"
print "===================================="
local_com_port = COM_PORT_ENG
# Open serial port
print "Open serial port " + local_com_port
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print "COM port OK"
except:
print "Error COM port"
sys.exit(0)
usb2io_sendcmd(ser, "hello\r\n")
print "Configure I2C"
usb2io_sendcmd(ser, "i2c configure 0\r\n")
print("Configuring 4 pins to spi repeater...")
usb2io_sendcmd(ser, "gpio configure 2, 7\r\n")
usb2io_sendcmd(ser, "gpio configure 3, 7\r\n")
usb2io_sendcmd(ser, "gpio configure 4, 7\r\n")
usb2io_sendcmd(ser, "gpio configure 5, 7\r\n")
print("Configuring pin 0 as reset")
# reset lo
usb2io_sendcmd(ser, "gpio configure 0, 1\r\n")
usb2io_sendcmd(ser, "gpio configure 0, 2\r\n")
#put data to buffer
data = bytearray(data_count)
for i in range(0, data_count):
data[i] = i + 1
# send to target
print("Sending buffer...")
if (put_buffer(ser, data) == 0):
sys.exit(0)
print("RS485 Wreading...")
# format: uart wreadbuffer channel, data_count
res = usb2io_sendcmd(ser, "rs485 wreadbuffer 4," + str(data_count) + "\r\n")
if (res.find("OK") != -1):
# parse result
bytes_str = res[3:]
rx_cnt = int(bytes_str, 10)
# print "received = " + str(rx_cnt)
(status, data_out) = get_buffer(ser, rx_cnt)
if (status == True):
print data_out.encode("hex")
else:
print "Get buffer failed"
print "\r\n"
else:
print "failed."
data[i * 8 + 3] = (sR >> 24) & 0xFF
data[i * 8 + 4] = sL & 0xFF
data[i * 8 + 5] = (sL >> 8) & 0xFF
data[i * 8 + 6] = (sL >> 16) & 0xFF
data[i * 8 + 7] = (sL >> 24) & 0xFF
# send to target
print("Sending buffer...")
print("len = " + str(len(data)))
if (put_buffer(ser, data) == 0):
sys.exit(0)
print("Starting...")
usb2io_sendcmd(ser, "i2s wreadbuf 1, " + str(data_cnt) + "\r\n")
print("Busy...")
done = 0
while (done == 0):
rrd = ser.readline()
if (rrd != ''):
print(rrd)
else:
print('.')
if (rrd == 'OK\r\n'):
done = 1
# get buffer
print("Reading...")
(status, data_out) = get_buffer(ser, data_cnt * 4)
print "* I2C writebuffer sync"
print "===================================="
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print "Open serial port " + local_com_port
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print "COM port OK"
except:
print "Error COM port"
sys.exit(0)
print "Configure pin [0] to WFG mode"
usb2io_sendcmd(ser, "gpio configure 2,4\r\n")
# Set Ext voltage to 3.3V
print "Configure EXT voltage to 3.3V"
usb2io_sendcmd(ser, "expv write 3300\r\n")
print "Configure WFG"
# configure wfg
# the configuration should be sent to uC with put_buffer command. See description of "waveform gen configure" for config structure
data = bytearray(32 + segment_size * 2)
data[0] = sample_rate & 0xFF
data[1] = (sample_rate >> 8) & 0xFF
data[2] = (sample_rate >> 16) & 0xFF
data[3] = (sample_rate >> 24) & 0xFF
print "Open serial port " + local_com_port
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print "COM port OK"
except:
print "Error COM port"
sys.exit(0)
wro = ser.write("hello\r\n")
time.sleep(0.1)
rrd = ser.readline()
print(rrd)
# pin 2..5 - SPI
print "Configure pins [2..5] to SPI mode"
usb2io_sendcmd(ser, "gpio configure 2,7\r\n")
usb2io_sendcmd(ser, "gpio configure 3,7\r\n")
usb2io_sendcmd(ser, "gpio configure 4,7\r\n")
usb2io_sendcmd(ser, "gpio configure 5,7\r\n")
# Set Ext voltage to 3.3V
print "Configure EXT voltage to 3.3V"
usb2io_sendcmd(ser, "expv write 3300\r\n")
#print "Configure SPI: Set 100KHz clock, Polarity low, CS active high, Phase 1st, MSB"
usb2io_sendcmd(ser, "spi configure 1,0,0,0,100000,0\r\n")
print "Read from SPI device 32 bytes"
usb2io_sendcmd(ser, "spi read 1,32\r\n")
print "Write to SPI device 2 bytes and read back"
#=====================================================
import os
import sys
import time
import serial
import select
import struct
from usb2io import usb2io_sendcmd
COM_PORT_ENG = 'COM17'
#---- Application ---------------------------------------------------------
print "===================================="
print "* DCMI camera fpga test *"
print "===================================="
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port7
print "Open serial port " + local_com_port
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print "COM port OK"
except:
print "Error COM port"
sys.exit(0)
usb2io_sendcmd(ser, "fpga camera start 1\r\n") # Close serial port
ser.close()
raw_input("Press Enter to exit ...")
print "===================================="
print "* AK4954 Config"
print "===================================="
local_com_port = COM_PORT_ENG
# Open serial port
print "Open serial port " + local_com_port
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print "COM port OK"
except:
print "Error COM port"
sys.exit(0)
usb2io_sendcmd(ser, "hello\r\n")
print "Configure I2C"
usb2io_sendcmd(ser, "i2c configure 0\r\n")
print("Configuring 4 pins to spi repeater...")
usb2io_sendcmd(ser, "gpio configure 2, 7\r\n")
usb2io_sendcmd(ser, "gpio configure 3, 7\r\n")
usb2io_sendcmd(ser, "gpio configure 4, 7\r\n")
usb2io_sendcmd(ser, "gpio configure 5, 7\r\n")
print("Configuring pin 0 as reset")
# reset lo
usb2io_sendcmd(ser, "gpio configure 0, 1\r\n")
usb2io_sendcmd(ser, "gpio configure 0, 2\r\n")
def writeRegister(self, addr, val):
if (usb2io_sendcmd(
self.ser, "i2c write 1, " + str(AS7265X_ADDR) + ", " +
str(addr) + ", " + str(val) + "\r\n", 1) == "OK\r\n"):
return True
return False
wro = ser.write(strx)
time.sleep(0.02)
rrd = ser.readline()
# Open serial port
print "Open serial port " + local_com_port
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print "COM port OK"
except:
print "Error COM port"
sys.exit(0)
print "Configure EXT voltage to 3.3V"
usb2io_sendcmd(ser, "expv write 3300\r\n")
print "Configure PIN"
usb2io_sendcmd(ser, "gpio configure 0, 22\r\n", 1)
usb2io_sendcmd(ser, "gpio configure 1, 22\r\n", 1)
usb2io_sendcmd(ser, "gpio configure 2, 22\r\n", 1)
usb2io_sendcmd(ser, "gpio configure 3, 22\r\n", 1)
usb2io_sendcmd(ser, "gpio configure 4, 22\r\n", 1)
usb2io_sendcmd(ser, "gpio configure 5, 22\r\n", 1)
usb2io_sendcmd(ser, "gpio configure 6, 22\r\n", 1)
usb2io_sendcmd(ser, "gpio configure 7, 22\r\n", 1)
usb2io_sendcmd(ser, "gpio configure 8, 22\r\n", 1)
usb2io_sendcmd(ser, "gpio configure 9, 22\r\n", 1)
usb2io_sendcmd(ser, "gpio configure 10, 22\r\n", 1)
usb2io_sendcmd(ser, "gpio configure 11, 22\r\n", 1)
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print "Open serial port " + local_com_port
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print "COM port OK"
except:
print "Error COM port"
sys.exit(0)
TRX_TIMEOUT = 300
print "Configure pin [0] to WFG mode"
usb2io_sendcmd(ser, "gpio configure 0,4\r\n")
print ("Configure WFG")
# configure wfg
# the configuration should be sent to uC with put_buffer command. See description of "waveform gen configure" for config structure
data = bytearray(32 + segment_size * 2)
data[0] = sample_rate & 0xFF;
data[1] = (sample_rate >> 8) & 0xFF;
data[2] = (sample_rate >> 16) & 0xFF;
data[3] = (sample_rate >> 24) & 0xFF;
data[4] = segment_size & 0xFF;
data[5] = (segment_size >> 8) & 0xFF;
COM_PORT_ENG = 'COM132'
#---- Application ---------------------------------------------------------
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print("Open serial port " + local_com_port)
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print("COM port OK")
except:
print("Error COM port")
sys.exit(0)
usb2io_sendcmd(ser, "hello\r\n")
# Set MDIO pinmux
usb2io_sendcmd(ser, "gpio configure 2, 11\r\n", silent = 1)
usb2io_sendcmd(ser, "gpio configure 3, 11\r\n", silent = 1)
# Set Ext voltage to 2.5V
usb2io_sendcmd(ser, "expv write 2500\r\n", silent = 1)
# Reset PHY and start autonegotiation
usb2io_sendcmd(ser, "mdio write 1,0,0x9200\r\n", silent = 1)
# Close serial port
ser.close()
print("MDIO test done")
print "* GPIO 6 - PRE"
print "* GPIO 7 - Trigger"
print "===================================="
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print "Open serial port " + local_com_port
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print "COM port OK"
except:
print "Error COM port"
sys.exit(0)
usb2io_sendcmd(ser, "hello\r\n")
print("Configuring pins to LTC2500...")
if (usb2io_sendcmd(ser, "gpio configure 0, 15\r\n", 1) != "OK\r\n"):
print "failed."
sys.exit(0)
if (usb2io_sendcmd(ser, "gpio configure 1, 15\r\n", 1) != "OK\r\n"):
print "failed."
sys.exit(0)
if (usb2io_sendcmd(ser, "gpio configure 2, 15\r\n", 1) != "OK\r\n"):
print "failed."
sys.exit(0)
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print("Open serial port " + local_com_port)
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print("COM port OK")
except:
print("Error COM port")
sys.exit(0)
print("Starting step motor cntroller...")
# start channel 1
#if usb2io_sendcmd(ser, "stepmotor start 1\r\n") != "OK\r\n":
# print "failed."
# sys.exit(0)
# start channel 2
#if usb2io_sendcmd(ser, "stepmotor start 2\r\n") != "OK\r\n":
# print "failed."
# sys.exit(0)
# start all channels
if usb2io_sendcmd(ser, "stepmotor start 0\r\n") != "OK\r\n":
print("failed.")
sys.exit(0)
input("Press Enter to exit...")
AddCommand(buffer, 0xad) #/* master configuration */
AddCommand(buffer, 0x8e) #/* external vcc supply */
AddCommand(buffer, 0xc8) #/* set com scan direction */
AddCommand(buffer, 0xd3) #/* set display offset */
AddCommand(buffer, 0x40) #
AddCommand(buffer, 0xd5) #/* set display clock divide/oscillator frequency */
AddCommand(buffer, 0xf0) #
AddCommand(buffer, 0xD8) #/*set area color mode off */
AddCommand(buffer, 0x05) #
AddCommand(buffer, 0xD9) #
AddCommand(buffer, 0xF1) #
AddCommand(buffer, 0xda) #/* set com pin configuartion */
AddCommand(buffer, 0x12) #
AddCommand(buffer, 0x91) #
AddCommand(buffer, 0x3F) #
AddCommand(buffer, 0x3F) #
AddCommand(buffer, 0x3F) #
AddCommand(buffer, 0x3F) #
AddCommand(buffer, 0xaf) # /* set display on */
# send buffer to uC SDRAM
if (put_buffer(ser, buffer) == 0):
sys.exit(0)
usb2io_sendcmd(ser, "lcd fpga buffer write " + str(len(buffer) / 2) + "\r\n")
ser.close()
print "Done"
raw_input("Press Enter to exit ...")
print("* GPIO 6 - Tx")
print("* GPIO 7 - phy S")
print("* GPIO 8 - phy FLT")
print("* GPIO 9 - Rx")
print("====================================")
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print("Open serial port " + local_com_port)
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print("COM port OK")
except:
print("Error COM port")
sys.exit(0)
usb2io_sendcmd(ser, "hello\r\n")
print("Configuring 4 gpio pins...")
usb2io_sendcmd(ser, "gpio configure 7, 1\r\n") # silent mode OFF
usb2io_sendcmd(ser, "gpio configure 8, 0\r\n") # input
usb2io_sendcmd(ser, "gpio configure 9, 9\r\n") # FDCAN1 repeater
usb2io_sendcmd(ser, "gpio configure 6, 9\r\n") # FDCAN1 repeater
print("Configuring CAN bus (1Mbps baudrate, no CAN FD)")
usb2io_sendcmd(ser, "fdcan configure 1000000, 0\r\n") #
input("Press Enter to exit ...")
import serial
import select
from usb2io import usb2io_sendcmd
COM_PORT_ENG = 'COM17'
# port select. 1 - stm32, 2 - fpga
port = 1
#---- Application ---------------------------------------------------------
print("====================================")
print("* I2C scan")
print("====================================")
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print("Open serial port " + local_com_port)
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print("COM port OK")
except:
print("Error COM port")
sys.exit(0)
print("Scan I2C bus")
rrd = usb2io_sendcmd(ser, "i2c scan " + str(port) + "\r\n", 1)
print(rrd)
# Close serial port
ser.close()
input("Press Enter to exit ...")
#=====================================================
# FDCAN send std message
#=====================================================
import os
import sys
import time
import serial
import select
from usb2io import usb2io_sendcmd
COM_PORT_ENG = 'COM17'
#---- Application ---------------------------------------------------------
print "===================================="
print "* FDCAN send std message"
print "===================================="
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print "Open serial port " + local_com_port
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print "COM port OK"
except:
print "Error COM port"
sys.exit(0)
usb2io_sendcmd(ser, "fdcan send std 0x123, 1 , 2, 3, 4, 5, 6, 7, 8\r\n")
raw_input("Press Enter to exit ...")
#=====================================================
import os
import sys
import time
import serial
import select
from usb2io import usb2io_sendcmd
COM_PORT_ENG = 'COM17'
#---- Application ---------------------------------------------------------
print("====================================")
print("* FDCAN send ext message")
print("====================================")
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print("Open serial port " + local_com_port)
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print("COM port OK")
except:
print("Error COM port")
sys.exit(0)
usb2io_sendcmd(
ser, "fdcan send ext 0x1BAC1234, 10 , 11, 12, 13, 14, 15, 16, 17\r\n")
input("Press Enter to exit ...")
print "===================================="
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print "Open serial port " + local_com_port
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print "COM port OK"
except:
print "Error COM port"
sys.exit(0)
print("Configuring pins + reset..")
if usb2io_sendcmd(ser, "gpio configure 2, 0\r\n") != "OK\r\n":
print "failed."
sys.exit(0)
time.sleep(0.1)
if usb2io_sendcmd(ser, "gpio configure 0, 1\r\n") != "OK\r\n":
print "failed."
sys.exit(0)
time.sleep(0.1)
if usb2io_sendcmd(ser, "gpio configure 0, 2\r\n") != "OK\r\n":
print "failed."
sys.exit(0)
time.sleep(1)
device = AS7265x(ser)
import select
from usb2io import usb2io_sendcmd
COM_PORT_ENG = 'COM17'
#---- Application ---------------------------------------------------------
print "===================================="
print "* UART1 config"
print "* pin connection:"
print "* GPIO10 - UART1 Rx"
print "* GPIO11 - UART1 Tx"
print "* GPIO12 - UART1 RTS"
print "* GPIO13 - UART1 CTS"
print "===================================="
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print "Open serial port " + local_com_port
try:
ser = serial.Serial(local_com_port, 115200, timeout=30)
print "COM port OK"
except:
print "Error COM port"
sys.exit(0)
print("Reading...")
# format: uart read channel, timeout\r\n
usb2io_sendcmd(ser, "uart read 1, 1000\r\n")
raw_input("Press Enter to exit ...")
print "Error COM port"
sys.exit(0)
data = bytearray(data_cnt * 8)
for i in range(0, data_cnt):
sampleR = int(0x40000000 + 0x40000000 * math.sin(2 * 3.14 * i / 44))
sampleL = int(0x40000000 + 0x40000000 * math.sin(2 * 3.14 * i / 11))
#sampleR = 0
#sampleR = 0
data[i * 8] = sampleR & 0xFF
data[i * 8 + 1] = (sampleR >> 8) & 0xFF
data[i * 8 + 2] = (sampleR >> 16) & 0xFF
data[i * 8 + 3] = (sampleR >> 24) & 0xFF
data[i * 8 + 4] = sampleL & 0xFF
data[i * 8 + 5] = (sampleL >> 8) & 0xFF
data[i * 8 + 6] = (sampleL >> 16) & 0xFF
data[i * 8 + 7] = (sampleL >> 24) & 0xFF
# send to target
print("Sending buffer...")
print("len = " + str(len(data)))
if (put_buffer(ser, data) == 0):
sys.exit(0)
print("Starting...")
usb2io_sendcmd(ser, "i2s writebuffer 1, " + str(data_cnt) + "\r\n")
raw_input("Press Enter to exit ...")
print("* DRV8711EVB J2 B- = Blue")
print("* DRV8711EVB using motor ACT-Motor 23HS8430, Vsupply = 12V, 5Amax")
print("====================================")
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print("Open serial port " + local_com_port)
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print("COM port OK")
except:
print("Error COM port")
sys.exit(0)
usb2io_sendcmd(ser, "hello\r\n")
print("Configuring 4 pins to step motor controller...")
if usb2io_sendcmd(ser, "gpio configure 0, 13\r\n") != "OK\r\n":
print("failed.")
sys.exit(0)
if usb2io_sendcmd(ser, "gpio configure 1, 13\r\n") != "OK\r\n":
print("failed.")
sys.exit(0)
if usb2io_sendcmd(ser, "gpio configure 14, 16\r\n") != "OK\r\n":
print("failed.")
sys.exit(0)
import serial
import select
from usb2io import usb2io_sendcmd
COM_PORT_ENG = 'COM17'
#---- Application ---------------------------------------------------------
print("====================================")
print("* FDCAN recv signle message")
print("====================================")
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print("Open serial port " + local_com_port)
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print("COM port OK")
except:
print("Error COM port")
sys.exit(0)
c_time = time.time() * 1000.
while (1):
rx_out = usb2io_sendcmd(ser, "fdcan recv single\r\n", 1)
d_time = (time.time() * 1000.) - c_time
c_time = time.time() * 1000.
print("[%f] %s " % (d_time, rx_out))
input("Press Enter to exit ...")
import time
import serial
import select
from usb2io import usb2io_sendcmd
COM_PORT_ENG = 'COM17'
# port select. 1 - stm32, 2 - fpga
port = 2
#---- Application ---------------------------------------------------------
print "===================================="
print "* IIC Reading"
print "===================================="
local_com_port = COM_PORT_ENG
# Open serial port
print "Open serial port " + local_com_port
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print "COM port OK"
except:
print "Error COM port"
sys.exit(0)
usb2io_sendcmd(ser, "i2c write " + str(port) + ", 0x12, 0x04\r\n")
usb2io_sendcmd(ser, "i2c read " + str(port) + ", 0x12, 3\r\n")
# Close serial port
ser.close()
raw_input("Press Enter to exit...")
if (not file_path):
print "no file selected"
sys.exit(0)
file_size = os.path.getsize(file_path)
print("file size = " + str(file_size))
if (file_size == 0):
sys.exit(0)
if ((file_size & 0x01) != 0):
print "WARNING! File size is odd. " + str(
file_size + 1) + " bytes will be sent instead."
f = open(file_path, 'rb')
if (f == None):
print "can not open file."
sys.exit(0)
data = bytearray(f.read())
f.close()
if ((len(data) & 0x01) != 0):
data.append(0x5A)
if (put_buffer(ser, data) == 0):
sys.exit(0)
usb2io_sendcmd(ser, "service serial bufsend " + str(len(data) / 2) + "\r\n")
raw_input("Press Enter to exit...")
#=====================================================
import os
import sys
import time
import serial
import select
from usb2io import usb2io_sendcmd
COM_PORT_ENG = 'COM17'
#---- Application ---------------------------------------------------------
print ("====================================")
print ("* Hello app")
print ("====================================")
local_com_port = sys.argv[1] if (len(sys.argv) > 1) else COM_PORT_ENG
# Open serial port
print ("Open serial port " + local_com_port)
try:
ser = serial.Serial(local_com_port, 115200, timeout=3)
print ("COM port OK")
except:
print ("Error COM port")
sys.exit(0)
rrd = usb2io_sendcmd(ser, "hello\r\n", 1)
print(rrd)
input("Press Enter to exit...")
