class PowerSupply():
def __init__(self, com_port):
self.com_port = com_port
self.device = KoradSerial(com_port, True)
self.device.output.off()
channel = self.device.channels[0]
channel.voltage = 12.0
channel.current = 2.0
def poweroff(self):
self.device.output.off()
def poweron(self):
self.device.output.on()
def __del__(self):
self.device.close()
class KoradSerialTest(TestCase):
def setUp(self):
self.device = KoradSerial('/dev/tty.usbmodemfd121', True)
self.overrideSkippedTests = False
def tearDown(self):
self.device.close()
def _pause(self, delay=1):
""" Give the power supply time to digest the commands.
:param delay: How long to pause. The default 1 second is overkill.
"""
sleep(delay)
def test_beep(self):
""" Test the BEEP command.
According to what I've read on the Internet, and confirmed by my trials, is that BEEP0 doesn't work.
Thus this test is useless.
:return:
"""
if not self.overrideSkippedTests:
return
self.device.beep.off()
status = self.device.status
self.assertEqual(OnOffState.off, status.beep)
self._pause()
self.device.beep.on()
status = self.device.status
self.assertEqual(OnOffState.on, status.beep)
def test_channel1(self):
""" Test Channel 1's functionality.
This test assumes a small load (perhaps 100 ohm) is on the power supply so a small amount of current is drawn.
"""
channel = self.device.channels[0]
# Turn off output and ensure that it's reading zeroes.
self.device.output.off()
self._pause()
self.assertEqual(0, channel.output_voltage)
self.assertEqual(0, channel.output_current)
# Set the current and voltage and ensure it's reporting back correctly.
channel.voltage = 12.34
channel.current = 1.234
self.assertAlmostEqual(12.34, channel.voltage, 2)
self.assertAlmostEqual(1.234, channel.current, 3)
# Set a different current and voltage to ensure that we're not reading old data.
channel.voltage = 3.30
channel.current = 0.123
self.assertAlmostEqual(3.30, channel.voltage, 2)
self.assertAlmostEqual(0.123, channel.current, 3)
# Turn on the output and ensure that current is flowing across the small load.
self.device.output.on()
self._pause()
self.assertAlmostEqual(3.30, channel.output_voltage, 2)
self.assertLess(0, channel.output_current)
self.device.output.off()
def test_lock(self):
""" Test the lock state.
Ha! Just kidding. This is a stub.
It appears that there is no command to alter the lock state.
While connected to a serial line and processing commands, the power supply is in a lock state.
"""
if not self.overrideSkippedTests:
return
pass
def test_memory(self):
""" Ensure that memory store/recall works.
A two-step process is required to set a memory.
* First, one must choose the memory number with a `recall()` command.
* Second, one must set the desired voltage and current limit.
* Third, one must save the memory with a `save()` command.
Recalling a memory setting simply requires calling the `recall()` command.
This goes through the test twice with different values to ensure what is read isn't old data.
"""
channel = self.device.channels[0]
m1 = self.device.memories[0]
m2 = self.device.memories[1]
m3 = self.device.memories[2]
m4 = self.device.memories[3]
# Pass one with the first set of values.
m1.recall()
channel.voltage = 1.00
channel.current = 0.100
m1.save()
m2.recall()
channel.voltage = 2.00
channel.current = 0.200
m2.save()
m3.recall()
channel.voltage = 3.00
channel.current = 0.300
m3.save()
m4.recall()
channel.voltage = 4.00
channel.current = 0.400
m4.save()
m1.recall()
self.assertAlmostEqual(1.00, channel.voltage, 2)
self.assertAlmostEqual(0.100, channel.current, 3)
m2.recall()
self.assertAlmostEqual(2.00, channel.voltage, 2)
self.assertAlmostEqual(0.200, channel.current, 3)
m3.recall()
self.assertAlmostEqual(3.00, channel.voltage, 2)
self.assertAlmostEqual(0.300, channel.current, 3)
m4.recall()
self.assertAlmostEqual(4.00, channel.voltage, 2)
self.assertAlmostEqual(0.400, channel.current, 3)
# Pass two with different values.
m1.recall()
channel.voltage = 5.00
channel.current = 0.500
m1.save()
m2.recall()
channel.voltage = 10.00
channel.current = 1.000
m2.save()
m3.recall()
channel.voltage = 15.00
channel.current = 1.500
m3.save()
m4.recall()
channel.voltage = 20.00
channel.current = 2.000
m4.save()
m1.recall()
self.assertAlmostEqual(5.00, channel.voltage, 2)
self.assertAlmostEqual(0.500, channel.current, 3)
m2.recall()
self.assertAlmostEqual(10.00, channel.voltage, 2)
self.assertAlmostEqual(1.000, channel.current, 3)
m3.recall()
self.assertAlmostEqual(15.00, channel.voltage, 2)
self.assertAlmostEqual(1.500, channel.current, 3)
m4.recall()
self.assertAlmostEqual(20.00, channel.voltage, 2)
self.assertAlmostEqual(2.000, channel.current, 3)
def test_model(self):
""" Test the IDN command.
Read the model number from the device.
"""
model = self.device.model
self.assertTrue(model.startswith("KORAD"))
def test_ocp(self):
""" Test Over Current Protection
There's no way to get feedback on these, so simply ensure that no exceptions are thrown.
"""
self.device.over_current_protection.on()
self._pause()
self.device.over_current_protection.off()
def test_ovp(self):
""" Test Over Voltage Protection
There's no way to get feedback on these, so simply ensure that no exceptions are thrown.
"""
self.device.over_voltage_protection.on()
self._pause()
self.device.over_voltage_protection.off()
def test_output(self):
""" Ensure the device is reporting the output on/off state correctly.
"""
self.device.output.on()
status = self.device.status
self.assertEqual(OnOffState.on, status.output)
self._pause()
self.device.output.off()
status = self.device.status
self.assertEqual(OnOffState.off, status.output)
def test_track(self):
""" Test the TRACK commands.
**NOTE:** The tests here are hypothetical.
I don't have a multi-channel power supply to actually test this against.
"""
if not self.overrideSkippedTests:
return
self.device.track(Tracking.parallel)
status = self.device.status
self.assertEqual(Tracking.parallel, status.tracking)
self._pause()
self.device.track(Tracking.series)
status = self.device.status
self.assertEqual(Tracking.series, status.tracking)
self._pause()
self.device.track(Tracking.independent)
status = self.device.status
self.assertEqual(Tracking.independent, status.tracking)
data = ' '.join(data)
saveFile.write(data +'\n') # write data to file
saveFile.close()
lastdAcq.set(str(datetime.datetime.now().strftime("%b %d %Y %H:%M:%S")))
a += float(daqInterval) / 60.0
if (len(tGraphic) >= int(round(24.0 / (float(daqInterval) / 60.0)))):
del tGraphic[0]
del i1Graphic[0]
del i2Graphic[0]
tGraphic = tGraphic + [a]
i1Graphic = i1Graphic + [float(ps1C)]
i2Graphic = i2Graphic + [float(ps2C)]
time.sleep(0.1)
print tGraphic
print i1Graphic
print i2Graphic
root.update_idletasks()
thread = threading.Thread(target=maincode)
#make measuring thread terminate when the user exits the window
thread.daemon = True
thread.start()
root.protocol("WM_DELETE_WINDOW", on_closing_Main)
root.mainloop()
ps1.output = 'off'
ps2.output = 'off'
ps1.close()
ps2.close()
#print(load)
#channel.voltage = 15
#channel.current = 2
#mydevice.output.on()
#load = channel.output_current
#print(load)
# #wait = input("press to continue" )
# wait = 'r'
# while wait == 'r':
# wait = input("press to continue: ")
# load = channel.output_current
# print(load)
#wait = input("press to continue: ")
mydevice.output.off()
mydevice.close()
# ser = serial.Serial('COM3')
# print(ser.name)
# #ser.write(b'VSET1:6.34')
# #ser.write(b'OUT1')
# text = 'VSET1:10.34'
# ser.write(text.encode('ascii'))
# sleep(0.1)
#
# text = 'OUT0'
# ser.write(text.encode('ascii'))
class KoradSerialTest(TestCase):
def setUp(self):
self.ps = KoradSerial(serial_port)
self.ps.output = OnOffState('off')
def tearDown(self):
self.ps.close()
def test_modelstring(self):
model = self.ps.model
self.assertTrue(
model.startswith('KORAD') or model.startswith('VELLEMAN'))
def test_statusclass(self):
status = self.ps.status
self.assertIsInstance(status.mode, OutputMode)
self.assertIsInstance(status.beep, OnOffState)
self.assertIsInstance(status.ocp, OnOffState)
self.assertIsInstance(status.ovp, OnOffState)
self.assertIsInstance(status.output, OnOffState)
def test_ocp(self):
self.ps.ocp = OnOffState('on')
self.assertEqual(self.ps.ocp.name, 'on')
self.ps.ocp = 'off'
self.assertEqual(self.ps.ocp.name, 'off')
def test_ovp(self):
self.ps.ovp = OnOffState('on')
self.assertEqual(self.ps.ovp.name, 'on')
self.ps.ovp = 'off'
self.assertEqual(self.ps.ovp.name, 'off')
def test_output(self):
self.ps.output = OnOffState('off')
self.assertEqual(self.ps.output.name, 'off')
self.ps.output = 'on'
self.assertEqual(self.ps.output.name, 'on')
def test_voltage(self):
self.ps.output = OnOffState('off')
voltage = self.ps.voltage_set
self.ps.voltage = 1
self.assertEqual(self.ps.voltage_actual, 0)
self.assertEqual(self.ps.voltage_set, 1)
self.ps.voltage = voltage
def test_current(self):
self.ps.output = OnOffState('off')
current = self.ps.current_set
self.ps.current = 1
self.assertEqual(self.ps.current_actual, 0)
self.assertEqual(self.ps.current_set, 1)
self.ps.current = current
def test_memory(self):
# remember saved values
self.ps.recall_from_memory(1)
c1, v1 = self.ps.current_set, self.ps.voltage_set
self.ps.recall_from_memory(2)
c2, v2 = self.ps.current_set, self.ps.voltage_set
self.ps.current = 2.0
self.ps.voltage = 5.0
self.ps.save_to_memory(1)
self.ps.current = 0.5
self.ps.voltage = 3.3
self.ps.save_to_memory(2)
self.ps.recall_from_memory(1)
self.assertEqual(self.ps.current_set, 2.0)
self.assertEqual(self.ps.voltage_set, 5.0)
self.ps.recall_from_memory(2)
self.assertEqual(self.ps.current_set, 0.5)
self.assertEqual(self.ps.voltage_set, 3.3)
self.ps.current = 1.5
self.ps.voltage = 8.0
self.ps.save_to_memory(1)
self.ps.current = 0.2
self.ps.voltage = 15.0
self.ps.save_to_memory(2)
self.ps.recall_from_memory(1)
self.assertEqual(self.ps.current_set, 1.5)
self.assertEqual(self.ps.voltage_set, 8.0)
self.ps.recall_from_memory(2)
self.assertEqual(self.ps.current_set, 0.2)
self.assertEqual(self.ps.voltage_set, 15.0)
# set backed up values
self.ps.current, self.ps.voltage = c2, v2
self.ps.save_to_memory(2)
self.ps.current, self.ps.voltage = c1, v1
self.ps.save_to_memory(1)
class KoradSerialTest(TestCase):
def setUp(self):
self.device = KoradSerial('/dev/tty.usbmodemfd121', True)
self.overrideSkippedTests = False
def tearDown(self):
self.device.close()
def _pause(self, delay=1):
""" Give the power supply time to digest the commands.
:param delay: How long to pause. The default 1 second is overkill.
"""
sleep(delay)
def test_beep(self):
""" Test the BEEP command.
According to what I've read on the Internet, and confirmed by my trials, is that BEEP0 doesn't work.
Thus this test is useless.
:return:
"""
if not self.overrideSkippedTests:
return
self.device.beep.off()
status = self.device.status
self.assertEqual(OnOffState.off, status.beep)
self._pause()
self.device.beep.on()
status = self.device.status
self.assertEqual(OnOffState.on, status.beep)
def test_channel1(self):
""" Test Channel 1's functionality.
This test assumes a small load (perhaps 100 ohm) is on the power supply so a small amount of current is drawn.
"""
channel = self.device.channels[0]
# Turn off output and ensure that it's reading zeroes.
self.device.output.off()
self._pause()
self.assertEqual(0, channel.output_voltage)
self.assertEqual(0, channel.output_current)
# Set the current and voltage and ensure it's reporting back correctly.
channel.voltage = 12.34
channel.current = 1.234
self.assertAlmostEqual(12.34, channel.voltage, 2)
self.assertAlmostEqual(1.234, channel.current, 3)
# Set a different current and voltage to ensure that we're not reading old data.
channel.voltage = 3.30
channel.current = 0.123
self.assertAlmostEqual(3.30, channel.voltage, 2)
self.assertAlmostEqual(0.123, channel.current, 3)
# Turn on the output and ensure that current is flowing across the small load.
self.device.output.on()
self._pause()
self.assertAlmostEqual(3.30, channel.output_voltage, 2)
self.assertLess(0, channel.output_current)
self.device.output.off()
def test_lock(self):
""" Test the lock state.
Ha! Just kidding. This is a stub.
It appears that there is no command to alter the lock state.
While connected to a serial line and processing commands, the power supply is in a lock state.
"""
if not self.overrideSkippedTests:
return
pass
def test_memory(self):
""" Ensure that memory store/recall works.
A two-step process is required to set a memory.
* First, one must choose the memory number with a `recall()` command.
* Second, one must set the desired voltage and current limit.
* Third, one must save the memory with a `save()` command.
Recalling a memory setting simply requires calling the `recall()` command.
This goes through the test twice with different values to ensure what is read isn't old data.
"""
channel = self.device.channels[0]
m1 = self.device.memories[0]
m2 = self.device.memories[1]
m3 = self.device.memories[2]
m4 = self.device.memories[3]
# Pass one with the first set of values.
m1.recall()
channel.voltage = 1.00
channel.current = 0.100
m1.save()
m2.recall()
channel.voltage = 2.00
channel.current = 0.200
m2.save()
m3.recall()
channel.voltage = 3.00
channel.current = 0.300
m3.save()
m4.recall()
channel.voltage = 4.00
channel.current = 0.400
m4.save()
m1.recall()
self.assertAlmostEqual(1.00, channel.voltage, 2)
self.assertAlmostEqual(0.100, channel.current, 3)
m2.recall()
self.assertAlmostEqual(2.00, channel.voltage, 2)
self.assertAlmostEqual(0.200, channel.current, 3)
m3.recall()
self.assertAlmostEqual(3.00, channel.voltage, 2)
self.assertAlmostEqual(0.300, channel.current, 3)
m4.recall()
self.assertAlmostEqual(4.00, channel.voltage, 2)
self.assertAlmostEqual(0.400, channel.current, 3)
# Pass two with different values.
m1.recall()
channel.voltage = 5.00
channel.current = 0.500
m1.save()
m2.recall()
channel.voltage = 10.00
channel.current = 1.000
m2.save()
m3.recall()
channel.voltage = 15.00
channel.current = 1.500
m3.save()
m4.recall()
channel.voltage = 20.00
channel.current = 2.000
m4.save()
m1.recall()
self.assertAlmostEqual(5.00, channel.voltage, 2)
self.assertAlmostEqual(0.500, channel.current, 3)
m2.recall()
self.assertAlmostEqual(10.00, channel.voltage, 2)
self.assertAlmostEqual(1.000, channel.current, 3)
m3.recall()
self.assertAlmostEqual(15.00, channel.voltage, 2)
self.assertAlmostEqual(1.500, channel.current, 3)
m4.recall()
self.assertAlmostEqual(20.00, channel.voltage, 2)
self.assertAlmostEqual(2.000, channel.current, 3)
def test_model(self):
""" Test the IDN command.
Read the model number from the device.
"""
model = self.device.model
self.assertTrue(model.startswith("KORAD"))
def test_ocp(self):
""" Test Over Current Protection
There's no way to get feedback on these, so simply ensure that no exceptions are thrown.
"""
self.device.over_current_protection.on()
self._pause()
self.device.over_current_protection.off()
def test_ovp(self):
""" Test Over Voltage Protection
There's no way to get feedback on these, so simply ensure that no exceptions are thrown.
"""
self.device.over_voltage_protection.on()
self._pause()
self.device.over_voltage_protection.off()
def test_output(self):
""" Ensure the device is reporting the output on/off state correctly.
"""
self.device.output.on()
status = self.device.status
self.assertEqual(OnOffState.on, status.output)
self._pause()
self.device.output.off()
status = self.device.status
self.assertEqual(OnOffState.off, status.output)
def test_track(self):
""" Test the TRACK commands.
**NOTE:** The tests here are hypothetical.
I don't have a multi-channel power supply to actually test this against.
"""
if not self.overrideSkippedTests:
return
self.device.track(Tracking.parallel)
status = self.device.status
self.assertEqual(Tracking.parallel, status.tracking)
self._pause()
self.device.track(Tracking.series)
status = self.device.status
self.assertEqual(Tracking.series, status.tracking)
self._pause()
self.device.track(Tracking.independent)
status = self.device.status
self.assertEqual(Tracking.independent, status.tracking)