def setUp(self):
"""Run at the begining of every test to setup the machine"""
plt.close("all")
test_obj = MachineIPMSM()
test_obj.rotor = LamHole(Rint=45e-3 / 2,
Rext=81.5e-3,
is_stator=False,
is_internal=True,
L1=0.9)
test_obj.rotor.hole = list()
test_obj.rotor.hole.append(
HoleM51(
Zh=8,
W0=0.016,
W1=pi / 6,
W2=0.004,
W3=0.01,
W4=0.002,
W5=0.01,
W6=0.002,
W7=0.01,
H0=0.01096,
H1=0.0015,
H2=0.0055,
))
test_obj.shaft = Shaft(Drsh=test_obj.rotor.Rint * 2, Lshaft=1.2)
test_obj.stator = LamSlotWind(Rint=0.09,
Rext=0.12,
is_internal=False,
is_stator=True,
L1=0.9,
slot=None)
test_obj.frame = Frame(Rint=0.12, Rext=0.12, Lfra=0.7)
self.test_obj = test_obj
def setUp(self):
"""Run at the begining of every test to setup the machine"""
plt.close("all")
test_obj = MachineIPMSM()
test_obj.rotor = LamHole(is_internal=True,
Rint=0.021,
Rext=0.075,
is_stator=False,
L1=0.7)
test_obj.rotor.bore = BoreFlower(N=8, Rarc=0.05, alpha=pi / 8)
test_obj.rotor.hole = list()
test_obj.rotor.hole.append(
HoleM50(
Zh=8,
W0=50e-3,
W1=2e-3,
W2=1e-3,
W3=1e-3,
W4=20.6e-3,
H0=17.3e-3,
H1=3e-3,
H2=0.5e-3,
H3=6.8e-3,
H4=0,
))
test_obj.rotor.axial_vent = list()
test_obj.rotor.axial_vent.append(
VentilationCirc(Zh=8, Alpha0=0, D0=5e-3, H0=40e-3))
test_obj.rotor.axial_vent.append(
VentilationCirc(Zh=8, Alpha0=pi / 8, D0=7e-3, H0=40e-3))
test_obj.shaft = Shaft(Drsh=test_obj.rotor.Rint * 2, Lshaft=1.2)
test_obj.stator = LamSlotWind(Rint=0.078,
Rext=0.104,
is_internal=False,
is_stator=True,
L1=0.8)
test_obj.stator.slot = None
test_obj.stator.axial_vent.append(
VentilationPolar(Zh=8, H0=0.08, D0=0.01, W1=pi / 8, Alpha0=pi / 8))
test_obj.stator.axial_vent.append(
VentilationPolar(Zh=8, H0=0.092, D0=0.01, W1=pi / 8, Alpha0=0))
test_obj.frame = Frame(Rint=0.104, Rext=0.114, Lfra=1)
self.test_obj = test_obj
def setUp(self):
"""Run at the begining of every test to setup the machine"""
plt.close("all")
test_obj = MachineIPMSM()
test_obj.rotor = LamHole(
Rint=45e-3 / 2, Rext=81.5e-3, is_stator=False, is_internal=True, L1=0.9
)
test_obj.rotor.hole = list()
test_obj.rotor.hole.append(
HoleM52(Zh=8, W0=27e-3, W3=16.2e-3, H0=1e-3, H1=5e-3, H2=1e-3)
)
test_obj.shaft = Shaft(Drsh=test_obj.rotor.Rint * 2, Lshaft=1.2)
test_obj.stator = LamSlotWind(
Rint=0.09, Rext=0.12, is_internal=False, is_stator=True, L1=0.9, slot=None
)
test_obj.frame = Frame(Rint=0.12, Rext=0.12, Lfra=0.7)
self.test_obj = test_obj
H1=1.25e-3,
H2=0.5e-3,
H3=6.8e-3,
H4=0,
))
test_obj.rotor.hole[0].magnet_0.Lmag = 0.3
test_obj.rotor.hole[0].magnet_1.Lmag = 0.5
test_obj.rotor.hole[0].magnet_0.mat_type.struct.rho = 1000
test_obj.rotor.hole[0].magnet_1.mat_type.struct.rho = 1000
test_obj.rotor.axial_vent = list()
test_obj.rotor.axial_vent.append(
VentilationCirc(Zh=8, Alpha0=0, D0=5e-3, H0=40e-3))
test_obj.rotor.axial_vent.append(
VentilationCirc(Zh=8, Alpha0=pi / 8, D0=7e-3, H0=40e-3))
test_obj.rotor.mat_type.struct.rho = 7600
test_obj.shaft = Shaft(Drsh=test_obj.rotor.Rint * 2, Lshaft=1.2)
test_obj.shaft.mat_type.struct.rho = 5000
test_obj.stator = LamSlotWind(Rint=0.078,
Rext=0.104,
is_internal=False,
is_stator=True,
L1=0.8,
Nrvd=0,
Kf1=0.95)
test_obj.stator.slot = None
test_obj.stator.winding = None
test_obj.stator.axial_vent.append(
VentilationPolar(Zh=8, H0=0.08, D0=0.01, W1=pi / 8, Alpha0=pi / 8))
test_obj.stator.axial_vent.append(
VentilationPolar(Zh=8, H0=0.092, D0=0.01, W1=pi / 8, Alpha0=0))
test_obj.stator.mat_type.struct.rho = 8000
