def __init__(self, bii):
super(ArduinoToolChain, self).__init__(bii)
self.hive_disk_image = self.bii.hive_disk_image
self.arduino = Arduino(bii, self.hive_disk_image)
def __init__(self, bii):
super(ArduinoToolChain, self).__init__(bii)
self.hive_disk_image = self.bii.hive_disk_image
self.arduino = Arduino(bii, self.hive_disk_image)
class ArduinoToolChain(CPPToolChain):
'''Arduino commands'''
group = 'arduino'
def __init__(self, bii):
super(ArduinoToolChain, self).__init__(bii)
self.hive_disk_image = self.bii.hive_disk_image
self.arduino = Arduino(bii, self.hive_disk_image)
def monitor(self, *parameters):
'''Open serial monitor
This is a small utility to send and receive text messages over the serial port'''
parser = argparse.ArgumentParser(description=self.monitor.__doc__,
prog="bii %s:monitor" % self.group)
parser.parse_args(*parameters)
try:
port = self.arduino.refresh_port()
monitor(self, ClientHiveManager(self.bii), port)
except Exception as e:
raise BiiException('Cannot open serial monitor: %s' % str(e))
def upload(self, *parameters):
'''Upload a firmware in Arduino'''
parser = argparse.ArgumentParser(description=self.upload.__doc__,
prog="bii %s:upload" % self.group)
parser.add_argument('firmware',
type=str,
nargs="?",
help='firmwares to upload')
parser.add_argument(
"--ssh",
type=str,
nargs="?",
default=argparse.SUPPRESS,
help='Upload by ssh. You can specify the IP (default 192.168.240.1)'
)
args = parser.parse_args(*parameters)
# Refresh the arduino port. Check if user's entered arduino settings
# FIXME: Leonardo board could fail sometimes because of its port reset
super(ArduinoToolChain, self).build(
) # Here initialize arduino settings if it doesn't exist
if 'ssh' in args:
ip = args.ssh or "192.168.240.1"
self.arduino.ssh_upload(args.firmware, ip)
else:
self.arduino.refresh_port()
self.arduino.upload(args.firmware)
self.bii.user_io.out.success('Upload finished')
def configure(self, *parameters):
'''HIDDEN not show configure from cmake_tool_chain '''
raise BiiException('''Use "cpp:configure"''')
def build(self, *parameters):
'''HIDDEN'''
raise BiiException(''' Build your program with:
> bii cpp:build
NOTE: Before building an Arduino project you should configure your project (just once):
1. "bii arduino:settings": Configure IDE, board, etc
2. "bii configure -t arduino": Activate toolchain
''')
def settings(self, *parameters):
'''Configure project settings for arduino'''
parser = argparse.ArgumentParser(description=self.settings.__doc__,
prog="bii %s:settings" % self.group)
parser.add_argument(
'--sdk',
help='SDK directory. Write "default" if you want biicode'
' tries to find some default directory')
parser.add_argument("--board", help="Arduino board's name")
parser.add_argument("--port",
help='Port where your Arduino is connected')
parser.add_argument(
"--need_reset",
choices=['true', 'false'],
help="True or False if your port'd need to be reseted")
args = parser.parse_args(*parameters) # for -h
settings = self.hive_disk_image.settings
if any([args.sdk, args.board, args.port, args.need_reset]):
arduino_settings_args(self.bii.user_io, args, settings)
else:
arduino_settings_wizard(self.bii.user_io, settings)
self.hive_disk_image.settings = settings
install_arduino_toolchain(self.bii)
regenerate_arduino_settings_cmake(self.bii)
class ArduinoToolChain(CPPToolChain):
'''Arduino commands'''
group = 'arduino'
def __init__(self, bii):
super(ArduinoToolChain, self).__init__(bii)
self.hive_disk_image = self.bii.hive_disk_image
self.arduino = Arduino(bii, self.hive_disk_image)
def monitor(self, *parameters):
'''Open serial monitor
This is a small utility to send and receive text messages over the serial port'''
parser = argparse.ArgumentParser(description=self.monitor.__doc__,
prog="bii %s:monitor" % self.group)
parser.parse_args(*parameters)
try:
port = self.arduino.refresh_port()
monitor(self, ClientHiveManager(self.bii), port)
except Exception as e:
raise BiiException('Cannot open serial monitor: %s' % str(e))
def upload(self, *parameters):
'''Upload a firmware in Arduino'''
parser = argparse.ArgumentParser(description=self.upload.__doc__,
prog="bii %s:upload" % self.group)
parser.add_argument('firmware', type=str, nargs="?", help='firmwares to upload')
parser.add_argument("--ssh", type=str, nargs="?", default=argparse.SUPPRESS,
help='Upload by ssh. You can specify the IP (default 192.168.240.1)')
args = parser.parse_args(*parameters)
# Refresh the arduino port. Check if user's entered arduino settings
# FIXME: Leonardo board could fail sometimes because of its port reset
super(ArduinoToolChain, self).build() # Here initialize arduino settings if it doesn't exist
if 'ssh' in args:
ip = args.ssh or "192.168.240.1"
self.arduino.ssh_upload(args.firmware, ip)
else:
self.arduino.refresh_port()
self.arduino.upload(args.firmware)
self.bii.user_io.out.success('Upload finished')
def configure(self, *parameters):
'''HIDDEN not show configure from cmake_tool_chain '''
raise BiiException('''Use "cpp:configure"''')
def build(self, *parameters):
'''HIDDEN'''
raise BiiException(''' Build your program with:
> bii cpp:build
NOTE: Before building an Arduino project you should configure your project (just once):
1. "bii arduino:settings": Configure IDE, board, etc
2. "bii configure -t arduino": Activate toolchain
''')
def settings(self, *parameters):
'''Configure project settings for arduino'''
parser = argparse.ArgumentParser(description=self.settings.__doc__,
prog="bii %s:settings" % self.group)
parser.add_argument('--sdk', help='SDK directory. Write "default" if you want biicode'
' tries to find some default directory')
parser.add_argument("--board", help="Arduino board's name")
parser.add_argument("--port", help='Port where your Arduino is connected')
parser.add_argument("--need_reset", choices=['true', 'false'],
help="True or False if your port'd need to be reseted")
args = parser.parse_args(*parameters) # for -h
settings = self.hive_disk_image.settings
if any([args.sdk, args.board, args.port, args.need_reset]):
arduino_settings_args(self.bii.user_io, args, settings)
else:
arduino_settings_wizard(self.bii.user_io, settings)
self.hive_disk_image.settings = settings
install_arduino_toolchain(self.bii)
regenerate_arduino_settings_cmake(self.bii)
