def nt_timestamp_test(dut):
"""Main test bench function.
TODO: no automatic validation of DUT output yet. Look at waveforms.
"""
# start the clock
cocotb.fork(clk_gen(dut.clk156, CLK_FREQ_MHZ))
# reset dut
yield rstn(dut.clk156, dut.rstn156)
# create axi lite writer, connect and reset
axi_writer = AXI_Lite_Writer()
axi_writer.connect(dut, dut.clk156, AXI_DATA_WIDTH, "ctrl")
yield axi_writer.rst()
# run simulation for a while
yield wait_n_cycles(dut.clk156, 1000)
# set number of clock cycles which shall pass until counter is incremented
# to 10
yield axi_writer.write(CPUREG_OFFSET_CTRL_CYCLES_PER_TICK, 10)
# run simulation for a while
yield wait_n_cycles(dut.clk156, 1000)
def nt_recv_filter_mac_top_test(dut):
"""Test bench main function."""
# start the clock
cocotb.fork(clk_gen(dut.clk, CLK_FREQ_MHZ))
# no software reset
dut.rst_sw <= 0
# reset the dut
yield rstn(dut.clk, dut.rstn)
# create, connect and reset AXI4-Lite writer
axi_lite_writer = AXI_Lite_Writer()
axi_lite_writer.connect(dut, dut.clk, AXI_CTRL_BIT_WIDTH, "ctrl")
yield axi_lite_writer.rst()
# create and reset AXI4-Stream writer
axis_writer = AXIS_Writer()
axis_writer.connect(dut, dut.clk, AXIS_BIT_WIDTH)
yield axis_writer.rst()
# create and reset AXI4-Stream reader
axis_reader = AXIS_Reader()
axis_reader.connect(dut, dut.clk, AXIS_BIT_WIDTH)
yield axis_reader.rst()
# start random toggling of axi stream reader tready
cocotb.fork(toggle_signal(dut.clk, dut.m_axis_tready))
# perform a set of test. each run will generate its own random mac
# addresses
for i in range(N_RUNS):
print("Test %d/%d" % (i + 1, N_RUNS))
yield perform_test(dut, axi_lite_writer, axis_writer, axis_reader)
def nt_recv_capture_rx_test(dut):
"""Test bench main function."""
# start the clock
cocotb.fork(clk_gen(dut.clk, CLK_FREQ_MHZ))
# do not issue software reset
dut.rst_sw <= 0
# reset the dut
yield rstn(dut.clk, dut.rstn)
# instantiate an AXI4-Stream writer, connect and reset it
axis_writer = AXIS_Writer()
axis_writer.connect(dut, dut.clk, DATAPATH_BIT_WIDTH)
yield axis_writer.rst()
# generate a couple of random Ethernet packets. For each packet, generate
# a 16 bit latency value and a 26 bit inter-packet time value
pkts = []
latencies = []
inter_packet_times = []
for _ in range(N_PACKETS):
pkts.append(gen_packet())
latencies.append(randint(0, 2**24-1))
inter_packet_times.append(randint(0, 2**28-1))
# meta and data FIFOs never become full
dut.fifo_meta_full_i <= 0
dut.fifo_data_full_i <= 0
# test 0: capture disabled
print("Performing test 1/%d" % (N_REPEATS+3))
yield perform_test(dut, axis_writer, pkts, latencies, inter_packet_times,
False, 0)
# test 1: max capture size: 1514 byte
print("Performing test 2/%d" % (N_REPEATS+3))
yield perform_test(dut, axis_writer, pkts, latencies, inter_packet_times,
True, 1514)
# test 2: max capture size: 0 byte
print("Performing test 3/%d" % (N_REPEATS+3))
yield perform_test(dut, axis_writer, pkts, latencies, inter_packet_times,
True, 0)
# perform some more tests for random capture sizes
for i in range(N_REPEATS):
print("Performing test %d/%d" % (3+i, N_REPEATS+3))
yield perform_test(dut, axis_writer, pkts, latencies,
inter_packet_times, True, randint(64, 1514))
def nt_recv_capture_mem_write_fifo_wrapper_test(dut):
"""Test bench main function."""
# start the clock
cocotb.fork(clk_gen(dut.clk, CLK_FREQ_MHZ))
# do not issue software reset
dut.rst_sw <= 0
# initially we do not read or write data to the FIFO
dut.rd_en_i <= 0
dut.wr_en_i <= 0
# initially do not add alignment data
dut.align_i <= 0
# reset the dut
yield rstn(dut.clk, dut.rstn)
# wait a few cycles
yield wait_n_cycles(dut.clk, 10)
for i, n_words in enumerate(N_INPUT_WORDS):
print("Test %d/%d" % (i + 1, len(N_INPUT_WORDS)))
# generate 64 bit input data
data64 = gen_input_data(n_words)
# convert 64 bit input data to 512 bit output data
data512 = convert_data_64_to_512(data64)
# start input coroutine
coroutine_in = cocotb.fork(apply_input(dut, data64))
# start ouput coroutine
coroutine_out = cocotb.fork(check_output(dut, data512))
# start one coroutine for triggering aligment
coroutine_align = cocotb.fork(trigger_align(dut, data64))
# wait for coroutines to complete
yield coroutine_in.join()
yield coroutine_out.join()
yield coroutine_align.join()
def nt_recv_interpackettime_test(dut):
"""Test bench main function."""
# start the clock
cocotb.fork(clk_gen(dut.clk156, CLK_FREQ_MHZ))
# no software reset
dut.rst_sw156 <= 0
# reset the DuT
yield rstn(dut.clk156, dut.rstn156)
# create an AXI4-Stream reader, connect and reset it
axis_reader = AXIS_Reader()
axis_reader.connect(dut, dut.clk156, AXIS_BIT_WIDTH)
yield axis_reader.rst()
# create an AXI4-Stream writer, connect and reset it
axis_writer = AXIS_Writer()
axis_writer.connect(dut, dut.clk156, AXIS_BIT_WIDTH)
yield axis_writer.rst()
# generate some random packets
pkts = []
for _ in range(N_PACKETS):
pkts.append(gen_packet())
# start random toggling of AXI4-Stream reader TREADY
cocotb.fork(toggle_signal(dut.clk156, dut.m_axis_tready))
# start one coroutine to apply packets on DuT input
cocotb.fork(packets_write(dut, axis_writer, pkts))
# start one coroutine to read packets on DuT output
coroutine_read = cocotb.fork(packets_read(dut, axis_reader, pkts))
# start one coroutine that monitors inter-packet times
cocotb.fork(monitor_inter_packet_time(dut))
# wait for coroutines to complete
yield coroutine_read.join()
def nt_recv_capture_fifo_merge(dut):
"""Test bench main function."""
# start the clock
cocotb.fork(clk_gen(dut.clk, CLK_FREQ_MHZ))
# do not issue software reset
dut.rst_sw <= 0
# output fifo is never full
dut.fifo_full_i <= 0
# intially not writing to input fifos
dut.fifo_meta_wr_en_i <= 0
dut.fifo_data_wr_en_i <= 0
# reset the dut
yield rstn(dut.clk, dut.rstn)
# wait a few cycles
yield wait_n_cycles(dut.clk, 5)
for i in range(N_REPEATS):
# print out some status
print("Test %d/%d" % (i+1, N_REPEATS))
# determine random maximum capture length
max_len_capture = random.randint(0, 1514)
# generate packet and meta data
(meta, data) = gen_input_data(max_len_capture)
# start stimulus coroutine
cocotb.fork(apply_input(dut, meta, data))
# start coroutine checking output
coroutine_chk = cocotb.fork(check_output(dut, meta, data,
max_len_capture))
# wat for checking coroutine to complete
yield coroutine_chk.join()
def nt_gen_replay_top_test(dut):
"""Test bench main function."""
# start the clock
cocotb.fork(clk_gen(dut.clk, CLK_FREQ_MHZ))
# no software reset
dut.rst_sw <= 0
# reset dut
yield rstn(dut.clk, dut.rstn)
# open trace file
trace = File("files/random.file")
# get trace file size
trace_size = trace.size()
# trace file must be a multiple of the AXI data width
if trace.size() % (AXI_MEM_BIT_WIDTH / 8) != 0:
raise cocotb.result.TestFailure("invalid trace size")
# calculate ring buffer sizes
ring_buff_sizes = []
for ring_buff_size in RING_BUFF_SIZES:
# size of ring buffer is determined by multiplying the size factor by
# the size of the trace
ring_buff_size = int(ring_buff_size * trace_size)
# make sure that the ring buffer size is multiple of AXI data width
if ring_buff_size % (AXI_MEM_BIT_WIDTH / 8) != 0:
ring_buff_size += AXI_MEM_BIT_WIDTH/8 - \
ring_buff_size % (AXI_MEM_BIT_WIDTH/8)
ring_buff_sizes.append(ring_buff_size)
# create a ring buffer memory (initially of size 0) and connect it to the
# DUT
ring_buff = Mem(0)
ring_buff.connect(dut, "ddr3")
# create axi lite writer, connect and reset
axi_lite_writer = AXI_Lite_Writer()
axi_lite_writer.connect(dut, dut.clk, AXI_LITE_BIT_WIDTH, "ctrl")
yield axi_lite_writer.rst()
# create axi lite reader, connect and reset
axi_lite_reader = AXI_Lite_Reader()
axi_lite_reader.connect(dut, dut.clk, AXI_LITE_BIT_WIDTH, "ctrl")
yield axi_lite_reader.rst()
# create axi stream reader, connect and reset
axis_reader = AXIS_Reader()
axis_reader.connect(dut, dut.clk, AXIS_BIT_WIDTH)
yield axis_reader.rst()
# start the ring buffer memory main routine
cocotb.fork(ring_buff.main())
# toggle m_axis_tready
cocotb.fork(toggle_signal(dut.clk, dut.m_axis_tready))
# iterate over all ring buffer sizes
for i, ring_buff_size in enumerate(ring_buff_sizes):
# set ring buffer size
ring_buff.set_size(ring_buff_size)
# iterate over all addresses where ring buffer shall be located in
# memory
for j, ring_buff_addr in enumerate(RING_BUFF_ADDRS):
# print status
print("Test %d/%d" % (i * len(RING_BUFF_ADDRS) + j + 1,
len(RING_BUFF_ADDRS) * len(RING_BUFF_SIZES)))
print("Ring Buff Addr: 0x%x, Size: %d" %
(ring_buff_addr, ring_buff_size))
# we have a total of 8 GByte of memory. Make sure the ring buffer
# fits at the desired address
if ring_buff_addr + ring_buff_size > 0x1FFFFFFFF:
raise cocotb.result.TestFailure("ring buffer is too large")
# to reduce the simulation memory footprint, provide the memory
# module the first memory address that we acutally care about
ring_buff.set_offset(ring_buff_addr)
# configure ring buffer memory location
yield axi_lite_writer.write(CPUREG_OFFSET_CTRL_MEM_ADDR_HI,
ring_buff_addr >> 32)
yield axi_lite_writer.write(CPUREG_OFFSET_CTRL_MEM_ADDR_LO,
ring_buff_addr & 0xFFFFFFFF)
# configure ring buffer address range
yield axi_lite_writer.write(CPUREG_OFFSET_CTRL_MEM_RANGE,
ring_buff_size - 1)
# configure trace size
yield axi_lite_writer.write(CPUREG_OFFSET_CTRL_TRACE_SIZE_HI,
trace_size >> 32)
yield axi_lite_writer.write(CPUREG_OFFSET_CTRL_TRACE_SIZE_LO,
trace_size & 0xFFFFFFFF)
# reset write address pointer
yield axi_lite_writer.write(CPUREG_OFFSET_CTRL_ADDR_WR, 0x0)
# make sure module initially is inactive
status = yield axi_lite_reader.read(CPUREG_OFFSET_STATUS)
if status & 0x3 != 0:
raise cocotb.reset.TestFailure("module is active")
# start the module
yield axi_lite_writer.write(CPUREG_OFFSET_CTRL_START, 0x1)
# wait a few cycles
yield wait_n_cycles(dut.clk, 10)
# start writing the ring buffer
cocotb.fork(
ring_buff_write(dut, ring_buff, trace, ring_buff_addr,
axi_lite_reader, axi_lite_writer))
# start coroutine that checks dut output
coroutine_chk_out = cocotb.fork(
check_output(dut, trace, axis_reader))
# wait a few cycles and make sure module is active
yield wait_n_cycles(dut.clk, 10)
status = yield axi_lite_reader.read(CPUREG_OFFSET_STATUS)
if status & 0x1 == 0x0:
raise cocotb.result.TestFailure("mem read not active")
if status & 0x2 == 0x0:
raise cocotb.result.TestFailure("packet assembly not active")
# wait for output check to complete
yield coroutine_chk_out.join()
# wait a few cycles
yield wait_n_cycles(dut.clk, 10)
# make sure module is now inactive
status = yield axi_lite_reader.read(CPUREG_OFFSET_STATUS)
if status & 0x3 != 0x0:
raise cocotb.result.TestFailure("module does not become " +
"inactive")
# clear the ring buffer contents
ring_buff.clear()
# close the trace file
trace.close()
def nt_gen_timestamp_insert_test(dut):
"""Test bench main function."""
# start the clock
cocotb.fork(clk_gen(dut.clk156, CLK_FREQ_MHZ))
# no software reset
dut.rst_sw156 <= 0
# reset the dut
yield rstn(dut.clk156, dut.rstn156)
# create an axi stream writer, connect it and reset if
axis_writer = AXIS_Writer()
axis_writer.connect(dut, dut.clk156, AXIS_BIT_WIDTH)
yield axis_writer.rst()
# create an axi stream reader, connect it and reset if
axis_reader = AXIS_Reader()
axis_reader.connect(dut, dut.clk156, AXIS_BIT_WIDTH)
yield axis_reader.rst()
# start the timestamp counter
cocotb.fork(timestamp_counter(dut))
# generate some ip packets
pkts = []
for _ in range(N_PACKETS):
pkts.append(gen_packet())
# initially we insert timestamps in the packet headers
dut.mode_i <= MODE_HEADER
print("Test Timestamp Header")
yield perform_test(dut, axis_writer, axis_reader, pkts)
# then we perform one test where we do not insert any timestamps at all
dut.mode_i <= MODE_DISABLED
print("Test Timestamp Disabled")
yield perform_test(dut, axis_writer, axis_reader, pkts)
# next run some random tests with timestamp inserted at fixed byte position
for i in range(N_REPEATS):
# generate some ip packets
pkts = []
for _ in range(N_PACKETS):
pkts.append(gen_packet())
# fixed byte position
dut.mode_i <= MODE_FIXED_POS
# randomly choose 16 bit or 24 bit timestamp width
width = randint(0, 1)
# find valid timestamp positions
while True:
pos = randint(0, 1518)
if width == 0 and (pos % 8) < 7:
break
elif width == 1 and (pos % 8) < 6:
break
# set timestamp position and width
dut.pos_i <= pos
dut.width_i <= width
# perform the test
print("Test Timestamp Fixed Pos %d/%d (Pos: %d, Width: %d)" %
(i + 1, N_REPEATS, pos, width))
yield perform_test(dut, axis_writer, axis_reader, pkts)
def nt_recv_latency_test(dut):
"""Test bench main function."""
# start the clock
cocotb.fork(clk_gen(dut.clk156, CLK_FREQ_MHZ))
# no software reset
dut.rst_sw156 <= 0
# reset the dut
yield rstn(dut.clk156, dut.rstn156)
# create an AXI4-Stream reader, connect and reset it
axis_reader = AXIS_Reader()
axis_reader.connect(dut, dut.clk156, AXIS_BIT_WIDTH)
yield axis_reader.rst()
# create an AXI4-Stream writer, connect and reset it
axis_writer = AXIS_Writer()
axis_writer.connect(dut, dut.clk156, AXIS_BIT_WIDTH)
yield axis_writer.rst()
# start random toggling of AXI4-Stream reader TREADY
cocotb.fork(toggle_signal(dut.clk156, dut.m_axis_tready))
# set current timestamp to be static at 8421376
dut.timestamp_i <= 8421376
yield RisingEdge(dut.clk156)
# generate 70% of N_PACKETS IP packets and insert random timestamp in
# packet header
n_packets_ip = int(0.7 * N_PACKETS)
pkts = []
timestamps = []
for _ in range(n_packets_ip):
pkt = gen_packet()
packet_insert_random_timestamp_header(pkt, timestamps)
pkts.append(pkt)
# then generate 30% of N_PACKETS non-IP packets. no timestamp will be
# inserted
for _ in range(N_PACKETS - n_packets_ip):
pkt = gen_packet(eth_only=True)
pkts.append(pkt)
timestamps.append(None)
# shuffle pkt and timestamp lists (in same order)
tmp = list(zip(pkts, timestamps))
shuffle(tmp)
pkts, timestamps = zip(*tmp)
# we inserted timestamps in packet header
dut.mode_i <= MODE_HEADER
print("Test Timestamp Header")
yield perform_test(dut, axis_writer, axis_reader, pkts, timestamps)
# perform another test where timestamping is disabled
dut.mode_i <= MODE_DISABLED
print("Test Timestamp Disabled")
yield perform_test(dut, axis_writer, axis_reader, pkts, timestamps)
# next run some random tests with timestamp inserted at fixed byte position
for i in range(N_REPEATS):
# fixed byte position
dut.mode_i <= MODE_FIXED_POS
# randomly choose 16 bit or 24 bit timestamp width
width = randint(0, 1)
# find valid timestamp positions
while True:
pos = randint(0, 1518)
if width == 0 and (pos % 8) < 7:
break
elif width == 1 and (pos % 8) < 6:
break
# set timestamp position and width
dut.pos_i <= pos
dut.width_i <= width
# generate some ip packets and insert random timestamps
pkts = []
timestamps = []
for _ in range(N_PACKETS):
pkt = gen_packet()
pkt = packet_insert_random_timestamp_fixed(pkt, timestamps, pos,
width)
pkts.append(pkt)
# perform the test
print("Test Timestamp Fixed Pos %d/%d (Pos: %d, Width: %d)" %
(i + 1, N_REPEATS, pos, width))
yield perform_test(dut, axis_writer, axis_reader, pkts, timestamps)
def nt_gen_rate_ctrl_top_test(dut):
"""Test bench main function."""
# initially module is inactive
dut.active_i <= 0
# no software reset
dut.rst_sw156 <= 0
# start the clock
cocotb.fork(clk_gen(dut.clk156, CLK_FREQ_MHZ))
# reset the DuT
yield rstn(dut.clk156, dut.rstn156)
# create AXI4-Stream writer and reader
axis_writer = AXIS_Writer()
axis_writer.connect(dut, dut.clk156, AXIS_BIT_WIDTH)
yield axis_writer.rst()
axis_reader = AXIS_Reader()
axis_reader.connect(dut, dut.clk156, AXIS_BIT_WIDTH)
yield axis_reader.rst()
# create AXI4-Lite writer and connect to DuT
axi_lite_writer = AXI_Lite_Writer()
axi_lite_writer.connect(dut, dut.clk156, AXI_CTRL_BIT_WIDTH, "ctrl")
yield axi_lite_writer.rst()
# create AXI4-Lite reader and connect to DuT
axi_lite_reader = AXI_Lite_Reader()
axi_lite_reader.connect(dut, dut.clk156, AXI_CTRL_BIT_WIDTH, "ctrl")
yield axi_lite_reader.rst()
# initially we are always ready to receive
dut.m_axis_tready <= 1
# start a coroutine that counts the number of cycles between two packets
# on the output axi stream
cocotb.fork(count_cycles_between_axis_transmission(dut))
print("Test 1/4")
# generate some packets and inter-packet times. we start with a constant
# inter-packet time of 200 cycles, more than enough to transmit each packet
pkts = []
for _ in range(N_PACKETS):
pkts.append((gen_packet(), 200))
# write packet data
cocotb.fork(packets_write(dut, axis_writer, pkts))
# wait a little
yield wait_n_cycles(dut.clk156, 500)
# start the module
dut.active_i <= 1
# start coroutine that checks output and wait until it completes
yield cocotb.fork(packets_read(dut, axis_reader, pkts, True))
# deactive the module
dut.active_i <= 0
# make sure no warning was flagged
status = yield axi_lite_reader.read(CPUREG_OFFSET_STATUS)
assert status == 0x0
print("Test 2/4")
# now generate packets of fixed size of 800 bytes. Since the datapath is
# 8 byte wide, it will take exactly 100 cycles to send them. Also select
# a fixed inter-packet time of 100 cycles. packets should be sent
# back-to-back
pkts = []
for _ in range(N_PACKETS):
pkt = Ether(src="53:00:00:00:00:01", dst="53:00:00:00:00:02")
pkt /= ''.join(
chr(random.randint(0, 255)) for _ in range(800 - len(pkt)))
pkts.append((pkt, 100))
# apply packet data
cocotb.fork(packets_write(dut, axis_writer, pkts))
# wait a little
yield wait_n_cycles(dut.clk156, 1000)
# start the module
dut.active_i <= 1
# start coroutine that checks output and wait until it completes
yield cocotb.fork(packets_read(dut, axis_reader, pkts, True))
# deactive the module
dut.active_i <= 0
# make sure no warning was flagged
status = yield axi_lite_reader.read(CPUREG_OFFSET_STATUS)
assert status == 0x0
print("Test 3/4")
# repeat the experiment, but decrement inter-packet time to 99 cycles.
# since inter-packet time is smaller than the packet transmit time, we
# should get a warning
pkts = []
for _ in range(N_PACKETS):
pkt = Ether(src="53:00:00:00:00:01", dst="53:00:00:00:00:02")
pkt /= ''.join(
chr(random.randint(0, 255)) for _ in range(800 - len(pkt)))
pkts.append((pkt, 99))
# apply packet data
cocotb.fork(packets_write(dut, axis_writer, pkts))
# wait a little
yield wait_n_cycles(dut.clk156, 500)
# start the module
dut.active_i <= 1
# start coroutine that checks output and wait until it completes
yield cocotb.fork(packets_read(dut, axis_reader, pkts, False))
# deactive the module
dut.active_i <= 0
# make sure a warning was flagged
status = yield axi_lite_reader.read(CPUREG_OFFSET_STATUS)
assert status == 0x1
# perform software reset to clear warning flag
yield axi_lite_writer.write(CPUREG_OFFSET_RST, 0x1)
# now start toggeling tready
cocotb.fork(toggle_signal(dut.clk156, dut.m_axis_tready))
print("Test 4/4")
# repeat the experiment, inter-packet time back at 100 cycles. since the
# slave is not always ready to receive, this should cause a warning
pkts = []
for _ in range(N_PACKETS):
pkt = Ether(src="53:00:00:00:00:01", dst="53:00:00:00:00:02")
pkt /= ''.join(
chr(random.randint(0, 255)) for _ in range(800 - len(pkt)))
pkts.append((pkt, 100))
# apply packet data
cocotb.fork(packets_write(dut, axis_writer, pkts))
# wait a little
yield wait_n_cycles(dut.clk156, 500)
# start the module
dut.active_i <= 1
# start coroutine that checks output and wait until it completes
yield cocotb.fork(packets_read(dut, axis_reader, pkts, False))
# deactive the module
dut.active_i <= 0
# make sure no warning was flagged
status = yield axi_lite_reader.read(CPUREG_OFFSET_STATUS)
assert status == 0x1
def nt_recv_capture_top_test(dut):
"""Test bench main function."""
# start the clock
cocotb.fork(clk_gen(dut.clk, CLK_FREQ_MHZ))
# no software reset
dut.rst_sw <= 0
# reset DuT
yield rstn(dut.clk, dut.rstn)
# create AXI4-Lite writer, connect and reset it
axilite_writer = AXI_Lite_Writer()
axilite_writer.connect(dut, dut.clk, AXI_CTRL_BIT_WIDTH, "ctrl")
yield axilite_writer.rst()
# create AXI4-Lite reader, connect and reset it
axilite_reader = AXI_Lite_Reader()
axilite_reader.connect(dut, dut.clk, AXI_CTRL_BIT_WIDTH, "ctrl")
yield axilite_reader.rst()
# create AXI4-Stream writer, connect and reset it
axis_writer = AXIS_Writer()
axis_writer.connect(dut, dut.clk, AXIS_BIT_WIDTH)
yield axis_writer.rst()
# create a ring buffer memory (initially of size 0) and connect it to the
# DuT
ring_buff = Mem(0)
ring_buff.connect(dut, "ddr3")
# generate a couple of random Ethernet packets. For each packet, generate
# a 16 bit latency value and a 26 bit inter-packet time value
pkts = []
latencies = []
inter_packet_times = []
for _ in range(N_PACKETS):
pkts.append(gen_packet())
latencies.append(random.randint(0, 2**24 - 1))
inter_packet_times.append(random.randint(0, 2**28 - 1))
# start the ring buffer memory main routine
cocotb.fork(ring_buff.main())
# wait some more clock cycles
yield wait_n_cycles(dut.clk, 5)
# iterate over all ring buffer sizes
for i, ring_buff_size in enumerate(RING_BUFF_SIZES):
# set ring buffer size
ring_buff.set_size(ring_buff_size)
# iterate over all adderesses where ring buffer shall be located in
# memory
for j, ring_buff_addr in enumerate(RING_BUFF_ADDRS):
# print status
print("Test %d/%d (this will take a while)" %
(i * len(RING_BUFF_ADDRS) + j + 1,
len(RING_BUFF_ADDRS) * len(RING_BUFF_SIZES)))
# we have a total of 8 GByte of memory. Make sure the ring buffer
# fits at the desired address
if ring_buff_addr + ring_buff_size > 0x1FFFFFFFF:
raise cocotb.result.TestFailure("ring buffer is too large")
# to reduce the simulation memory footprint, provide the memory
# module the first memory address that we actually care about
ring_buff.set_offset(ring_buff_addr)
# write ring buffer memory location and address range
yield axilite_writer.write(CPUREG_OFFSET_CTRL_MEM_ADDR_HI,
ring_buff_addr >> 32)
yield axilite_writer.write(CPUREG_OFFSET_CTRL_MEM_ADDR_LO,
ring_buff_addr & 0xFFFFFFFF)
yield axilite_writer.write(CPUREG_OFFSET_CTRL_MEM_RANGE,
ring_buff_size - 1)
# itererate over all capture lengths
for max_len_capture in MAX_CAPTURE_LENS:
# reset read address pointer
yield axilite_writer.write(CPUREG_OFFSET_CTRL_ADDR_RD, 0x0)
# set max capture length
yield axilite_writer.write(CPUREG_OFFSET_CTRL_MAX_LEN_CAPTURE,
max_len_capture)
# start couroutine that applies packets at input
cocotb.fork(
packets_write(dut, axis_writer, axilite_writer,
axilite_reader, pkts, latencies,
inter_packet_times))
# wait a bit
yield wait_n_cycles(dut.clk, 50)
# start the ring buffer read coroutine and wait until it
# completes
yield ring_buff_read(dut, axilite_writer, axilite_reader,
ring_buff, ring_buff_addr,
max_len_capture, pkts, latencies,
inter_packet_times)
# make sure no error occured
errs = yield axilite_reader.read(CPUREG_OFFSET_STATUS_ERRS)
assert errs == 0x0
# make sure packet count is correct
pkt_cnt = \
yield axilite_reader.read(CPUREG_OFFSET_STATUS_PKT_CNT)
assert pkt_cnt == len(pkts)
# make sure module is deactivated now
active = yield axilite_reader.read(CPUREG_OFFSET_STATUS_ACTIVE)
assert active == 0
# clear the ring buffer contents
ring_buff.clear()
def nt_gen_replay_mem_read_test(dut):
"""Test bench main function."""
# open trace file
trace = File("files/random.file")
# get trace file size
trace_size = trace.size()
# trace file size must be a multiple of AXI data width
if trace.size() % (AXI_BIT_WIDTH / 8) != 0:
raise cocotb.result.TestFailure("invalid trace size")
# calculate ring buffer sizes
ring_buff_sizes = []
for ring_buff_size in RING_BUFF_SIZES:
# size of ring buffer is determined by multiplying the size factor by
# the size of the trace
ring_buff_size = int(ring_buff_size * trace_size)
# make sure that the ring buffer size is multiple of AXI data width
if ring_buff_size % (AXI_BIT_WIDTH / 8) != 0:
ring_buff_size += AXI_BIT_WIDTH/8 - ring_buff_size % \
(AXI_BIT_WIDTH/8)
ring_buff_sizes.append(ring_buff_size)
# create a ring buffer memory (initially of size 0) and connect it to the
# DUT
ring_buff = Mem(0)
ring_buff.connect(dut)
# start the clock
cocotb.fork(clk_gen(dut.clk, CLK_FREQ_MHZ))
# deassert sw reset
dut.rst_sw <= 0
# initially module start is not triggered
dut.ctrl_start_i <= 0
# reset dut
yield rstn(dut.clk, dut.rstn)
# start the ring buffer memory main routine
cocotb.fork(ring_buff.main())
# wait some more clock cycles
yield wait_n_cycles(dut.clk, 5)
# randomly toggle fifo_prog_full input signal
dut.fifo_prog_full_i <= 0
cocotb.fork(toggle_signal(dut.clk, dut.fifo_prog_full_i))
# iterate over all ring buffer sizes
for i, ring_buff_size in enumerate(ring_buff_sizes):
# set ring buffer size
ring_buff.set_size(ring_buff_size)
# iterate over all adderesses where ring buffer shall be located in
# memory
for j, ring_buff_addr in enumerate(RING_BUFF_ADDRS):
# print status
print("Test %d/%d" % (i * len(RING_BUFF_ADDRS) + j + 1,
len(RING_BUFF_ADDRS) * len(RING_BUFF_SIZES)))
# we have a total of 8 GByte of memory. Make sure the ring buffer
# fits at the desired address
if ring_buff_addr + ring_buff_size > 0x1FFFFFFFF:
raise cocotb.result.TestFailure("ring buffer is too large")
# to reduce the simulation memory footprint, provide the memory
# module the first memory address that we actually care about
ring_buff.set_offset(ring_buff_addr)
# apply ring buffer memory location to dut
dut.ctrl_mem_addr_hi_i <= ring_buff_addr >> 32
dut.ctrl_mem_addr_lo_i <= ring_buff_addr & 0xFFFFFFFF
# apply ring buffer address range to dut
dut.ctrl_mem_range_i <= ring_buff_size - 1
# apply trace size to dut
dut.ctrl_trace_size_hi_i <= trace_size >> 32
dut.ctrl_trace_size_lo_i <= trace_size & 0xFFFFFFFF
# reset write address pointer
dut.ctrl_addr_wr_i <= 0
# start reading from the ring buffer
dut.ctrl_start_i <= 1
yield RisingEdge(dut.clk)
dut.ctrl_start_i <= 0
yield RisingEdge(dut.clk)
# start writing the ring buffer
cocotb.fork(ring_buff_write(dut, ring_buff, trace))
# start checking dut output and wait until it completes
yield cocotb.fork(check_output(dut, trace)).join()
# clear the ring buffer contents
ring_buff.clear()
# close trace file
trace.close()
def nt_recv_capture_rx_fifo_merge_test(dut):
"""Test bench main function."""
# start the clock
cocotb.fork(clk_gen(dut.clk, CLK_FREQ_MHZ))
# do not issue software reset
dut.rst_sw <= 0
# reset the dut
yield rstn(dut.clk, dut.rstn)
# instantiate an AXI4-Stream writer, connect and reset
axis_writer = AXIS_Writer()
axis_writer.connect(dut, dut.clk, DATAPATH_BIT_WIDTH)
yield axis_writer.rst()
# generate a couple of random Ethernet packets. For each packet, generate
# a 16 bit latency value and a 26 bit inter-packet time value
pkts = []
latencies = []
inter_packet_times = []
for _ in range(N_PACKETS):
pkts.append(gen_packet())
latencies.append(randint(0, 2**24 - 1))
inter_packet_times.append(randint(0, 2**28 - 1))
# initially output FIFO is not full
dut.fifo_full_i <= 0
# test: capture disabled
print("Performing test 1/%d" % (N_REPEATS + 5))
yield perform_test(dut, axis_writer, pkts, latencies, inter_packet_times,
False, 0)
# test: max capture size: 1514 byte
print("Performing test 2/%d" % (N_REPEATS + 5))
yield perform_test(dut, axis_writer, pkts, latencies, inter_packet_times,
True, 1514)
# test: max capture size: 0 byte
print("Performing test 3/%d" % (N_REPEATS + 5))
yield perform_test(dut, axis_writer, pkts, latencies, inter_packet_times,
True, 0)
# perform some more tests for random capture sizes
for i in range(N_REPEATS):
print("Performing test %d/%d" % (3 + i, N_REPEATS + 5))
yield perform_test(dut, axis_writer, pkts, latencies,
inter_packet_times, True, randint(64, 1514))
# now mark the fifo as full
dut.fifo_full_i <= 1
# perform another test and check data fifo error output signal
# should become full
print("Performing test %d/%d (no status output)" %
(N_REPEATS + 4, N_REPEATS + 5))
cocotb.fork(
perform_test(dut, axis_writer, pkts, latencies, inter_packet_times,
True, 1514))
# wait until all packets have been applied on AXI stream interface
pkt_cnt = 0
while pkt_cnt < len(pkts):
yield RisingEdge(dut.clk)
if int(dut.s_axis_tvalid) and int(dut.s_axis_tready) and \
int(dut.s_axis_tlast):
pkt_cnt += 1
# make sure the data fifo full error signal is asserted
assert int(dut.err_data_fifo_full_o)
# perform reset
dut.rst_sw <= 1
yield RisingEdge(dut.clk)
dut.rst_sw <= 0
yield RisingEdge(dut.clk)
# perform one final test to check whether the meta data fifo error signal
# is asserted when the fifo becomes full
print("Performing test %d/%d (no status output)" %
(N_REPEATS + 5, N_REPEATS + 5))
cocotb.fork(
perform_test(dut, axis_writer, pkts, latencies, inter_packet_times,
True, 0))
# wait until all packets have been applied on AXI stream interface
pkt_cnt = 0
while pkt_cnt < len(pkts):
yield RisingEdge(dut.clk)
if int(dut.s_axis_tvalid) and int(dut.s_axis_tready) and \
int(dut.s_axis_tlast):
pkt_cnt += 1
# make sure the meta fifo full error signal is asserted
assert int(dut.err_meta_fifo_full_o)
def nt_recv_capture_mem_write_test(dut):
"""Test bench main function."""
# open file with random content
try:
f = File("files/random.file")
except IOError:
raise cocotb.result.TestFailure("Generate input data by calling " +
"'./create_random.py' in 'files' " +
"folder!")
# file size must be a multiple of AXI data width
if f.size() % (BIT_WIDTH_MEM_WRITE / 8) != 0:
raise cocotb.result.TestFailure("invalid input data size")
# create a ring buffer memory (initially of size 0) and connect it to the
# DuT
ring_buff = Mem(0)
ring_buff.connect(dut)
# start the clock
cocotb.fork(clk_gen(dut.clk, CLK_FREQ_MHZ))
# deassert sw reset
dut.rst_sw <= 0
# initially module is disabled
dut.active_i <= 0
# initially no FIFO flush
dut.flush_i <= 0
# reset DuT
yield rstn(dut.clk, dut.rstn)
# start the ring buffer memory main routine
cocotb.fork(ring_buff.main())
# wait some more clock cycles
yield wait_n_cycles(dut.clk, 5)
# iterate over all ring buffer sizes
for i, ring_buff_size in enumerate(RING_BUFF_SIZES):
# set ring buffer size
ring_buff.set_size(ring_buff_size)
# iterate over all adderesses where ring buffer shall be located in
# memory
for j, ring_buff_addr in enumerate(RING_BUFF_ADDRS):
# print status
print("Test %d/%d" % (i * len(RING_BUFF_ADDRS) + j + 1,
len(RING_BUFF_ADDRS) * len(RING_BUFF_SIZES)))
# we have a total of 8 GByte of memory. Make sure the ring buffer
# fits at the desired address
if ring_buff_addr + ring_buff_size > 0x1FFFFFFFF:
raise cocotb.result.TestFailure("ring buffer is too large")
# to reduce the simulation memory footprint, provide the memory
# module the first memory address that we actually care about
ring_buff.set_offset(ring_buff_addr)
# apply ring buffer memory location to dut
dut.mem_addr_hi_i <= ring_buff_addr >> 32
dut.mem_addr_lo_i <= ring_buff_addr & 0xFFFFFFFF
# apply ring buffer address range to dut
dut.mem_range_i <= ring_buff_size - 1
# reset read address pointer
dut.addr_rd_i <= 0
# start a couroutine that applies input data
cocotb.fork(apply_input(dut, f))
# wait a few clock cycles
yield wait_n_cycles(dut.clk, 10)
# start the ring buffer read coroutine and wait until it completes
yield ring_buff_read(dut, ring_buff, f)
# clear the ring buffer contents
ring_buff.clear()
# close file
f.close()