def init_rc():
global rc
global rc_address
# Initialise the roboclaw motorcontroller
print("Initialising roboclaw driver...")
from roboclaw import Roboclaw
rc_address = 0x80
rc = Roboclaw("/dev/roboclaw", 115200)
rc.Open()
# Get roboclaw version to test if is attached
version = rc.ReadVersion(rc_address)
if version[0] is False:
print("Roboclaw get version failed")
sys.exit()
else:
print(repr(version[1]))
# Set motor controller variables to those required by K9
rc.SetM1VelocityPID(rc_address, M1_P, M1_I, M1_D, M1_QPPS)
rc.SetM2VelocityPID(rc_address, M2_P, M2_I, M2_D, M2_QPPS)
rc.SetMainVoltages(rc_address,232,290) # 23.2V min, 29V max
rc.SetPinFunctions(rc_address,2,0,0)
# Zero the motor encoders
rc.ResetEncoders(rc_address)
# Print Motor PID Settings
m1pid = rc.ReadM1VelocityPID(rc_address)
m2pid = rc.ReadM2VelocityPID(rc_address)
print("M1 P: " + str(m1pid[1]) + ", I:" + str(m1pid[2]) + ", D:" + str(m1pid[3]))
print("M2 P: " + str(m2pid[1]) + ", I:" + str(m2pid[2]) + ", D:" + str(m2pid[3]))
# Print Min and Max Main Battery Settings
minmaxv = rc.ReadMinMaxMainVoltages(rc_address) # get min max volts
print ("Min Main Battery: " + str(int(minmaxv[1])/10) + "V")
print ("Max Main Battery: " + str(int(minmaxv[2])/10) + "V")
# Print S3, S4 and S5 Modes
S3mode=['Default','E-Stop (latching)','E-Stop','Voltage Clamp','Undefined']
S4mode=['Disabled','E-Stop (latching)','E-Stop','Voltage Clamp','M1 Home']
S5mode=['Disabled','E-Stop (latching)','E-Stop','Voltage Clamp','M2 Home']
pinfunc = rc.ReadPinFunctions(rc_address)
print ("S3 pin: " + S3mode[pinfunc[1]])
print ("S4 pin: " + S4mode[pinfunc[2]])
print ("S5 pin: " + S5mode[pinfunc[3]])
print("Roboclaw motor controller initialised...")
from roboclaw import Roboclaw
from time import sleep
if __name__ == "__main__":
address = 0x80
roboclaw = Roboclaw("/dev/ttyS0", 38400)
roboclaw.Open()
roboclaw.SetM1VelocityPID(0x81,21.9,15.53,0,375)
roboclaw.SetM2VelocityPID(0x81,21.9,15.53,0,375)
while True:
roboclaw.BackwardM1(0x81,70)
roboclaw.BackwardM2(0x81,70)
sleep(3)
roboclaw.ForwardM1(0x81,55)
roboclaw.BackwardM2(0x81,55)
sleep(2)
roboclaw.BackwardM1(0x81,70)
roboclaw.BackwardM2(0x81,70)
sleep(3)
roboclaw.ForwardM1(0x81,0)
roboclaw.ForwardM2(0x81,0)
sleep(10)
#
# Initialise PID values on motor controller
#
import time # enable sleep function
from roboclaw import Roboclaw # enabling Roboclaw
rc = Roboclaw("/dev/roboclaw", 115200)
rc.Open()
rc_address = 0x80
version = rc.ReadVersion(rc_address)
if version[0] == False:
print "Roboclaw get version failed, exiting..."
sys.exit()
else:
print repr(version[1])
rc.SetM1VelocityPID(rc_address, 3000, 300, 0, 708)
rc.SetM2VelocityPID(rc_address, 3000, 300, 0, 720)
WriteNVM(self, address)
time.sleep(30)
print "Motor controller PID values intialised, exiting..."
print "Node-RED address is: " + str(address)
# Initialise the roboclaw motorcontroller
print "Initialising roboclaw driver..."
from roboclaw import Roboclaw
rc = Roboclaw("/dev/roboclaw", 115200)
rc.Open()
rc_address = 0x80
# Get roboclaw version to test if is attached
version = rc.ReadVersion(rc_address)
if version[0] is False:
print "Roboclaw get version failed"
sys.exit()
else:
print repr(version[1])
# Set PID variables to those required by K9
rc.SetM1VelocityPID(rc_address, 20000, 2000, 0, m1_qpps)
rc.SetM2VelocityPID(rc_address, 20000, 2000, 0, m2_qpps)
# Zero the motor encoders
rc.ResetEncoders(rc_address)
print "PID variables set on roboclaw"
# import RPi.GPIO as GPIO # enables manipulation of GPIO ports
# GPIO.setmode(GPIO.BOARD) # use board numbers rather than BCM numbers
# GPIO.setwarnings(False) # remove duplication warnings
# chan_list = [11, 13] # GPIO channels to initialise and use
# GPIO.setup(chan_list, GPIO.IN) # set GPIO to low at initialise
else:
# otherwise use local host as node-RED server
# and don't initialise GPIO or Roboclaw
address = "ws://127.0.0.1:1880/ws/motors"
class SerialDriver(object):
'''
Class for serial UART interface to the RoboClaw Motor Controllers
'''
def __init__(self):
rospy.loginfo("Initilizing the motor controllers..")
self.e_stop = 1
self.reg_enabled = 0
self.temp = 0
self.error = 0
self.voltage = 0
self.currents = [0,0]
self._thread_lock = False
self.prev_enc_ts = None
self.prev_tick = [None, None]
self.start_time = datetime.now()
self.left_currents = []
self.right_currents = []
self.max_left_integrator = 0
self.max_right_integrator = 0
self.left_integrator = 0
self.right_integrator = 0
self.motor_lockout = 0
self._cmd_buf_flag = 0
self._l_vel_cmd_buf = 0
self._r_vel_cmd_buf = 0
self.battery_percent = 0
self.shutdown_warning = False
self.shutdown_flag = False
self.rate = rospy.get_param("/puffer/rate")
self.delta_t = 2.0/self.rate
self.rc = Roboclaw(
rospy.get_param("/motor_controllers/serial_device_name"),
rospy.get_param("/motor_controllers/baud_rate")
)
self.rc.Open()
self._set_operating_params()
self._get_version()
self.set_estop(0) #Clears E-stop pin
self.enable_12v_reg(1) #Disables 12V Regulator
self.kill_motors() #Start the motors not moving
#Private Methods
def _get_version(self):
'''
Version check for communication verification to the motor controllers
returns ther version number if sucessful, and 0 if not
'''
version = self.rc.ReadVersion(self.address)
if version != 0:
rospy.loginfo("[Motor __init__ ] Sucessfully connected to all Motor Controllers!")
rospy.loginfo( version )
rospy.set_param("/motor_controllers/firmware_version",version)
else:
raise Exception("Unable to establish connection to Motor controllers")
return version
def _set_operating_params(self):
'''
Sets all the operating parameters for control of PUFFER, Pinouts, and
safety parameters.
returns None
'''
#GPIO settings for E-stop and Regulator Enable pins
self.e_stop_pin = rospy.get_param("/gpio_pins/e_stop",1)
self.reg_en_pin = rospy.get_param("/gpio_pins/reg_en",1)
try:
GPIO.setmode(GPIO.BCM)
GPIO.setwarnings(False)
GPIO.setup(self.e_stop_pin, GPIO.OUT)
GPIO.setup(self.reg_en_pin, GPIO.OUT)
except:
pass
#Threadlock used for serial comm to RoboClaw
self.thread_timeout = rospy.get_param("/threadlock/timeout")
#Motor operating parameters
self.wheel_d = rospy.get_param("/wheels/diameter")
self.enc_cpr = rospy.get_param("/wheels/encoder/cts_per_rev")
factor = rospy.get_param("/wheels/encoder/factor")
stage_1 = rospy.get_param("/wheels/gearbox/stage1")
stage_2 = rospy.get_param("/wheels/gearbox/stage2")
stage_3 = rospy.get_param("/wheels/gearbox/stage3")
self.accel_const = rospy.get_param("/puffer/accel_const")
self.max_vel_per_s = rospy.get_param("/puffer/max_vel_per_s")
self.tick_per_rev = int(self.enc_cpr * factor * stage_1 * stage_2 * stage_3)
rospy.loginfo(self.tick_per_rev)
rospy.set_param("tick_per_rev", self.tick_per_rev)
self.max_cts_per_s = int((self.max_vel_per_s * self.tick_per_rev)/(math.pi * self.wheel_d))
self.max_accel = int(self.max_cts_per_s * self.accel_const)
rospy.set_param("max_cts_per_s", self.max_cts_per_s)
rospy.set_param("max_accel", self.max_accel)
self.address = rospy.get_param("/motor_controllers/address", 0x80)
self.rc.SetMainVoltages(self.address,int(rospy.get_param("/motor_controllers/battery/main/low", 12.0) * 10),int(rospy.get_param("motor_controllers/battery/main/high", 18.0 ) * 10))
self.rc.SetLogicVoltages(self.address,int(rospy.get_param("/motor_controllers/battery/logic/low") * 10),int(rospy.get_param("motor_controllers/battery/logic/high") * 10))
self.max_current = rospy.get_param("/motor_controllers/current/max_amps")
self.motor_lockout_time = rospy.get_param("/puffer/motor_lockout_time")
m1p = rospy.get_param("/motor_controllers/m1/p")
m1i = rospy.get_param("/motor_controllers/m1/i")
m1d = rospy.get_param("/motor_controllers/m1/d")
m1qpps = rospy.get_param("/motor_controllers/m1/qpps")
m2p = rospy.get_param("/motor_controllers/m2/p")
m2i = rospy.get_param("/motor_controllers/m2/i")
m2d = rospy.get_param("/motor_controllers/m2/d")
m2qpps = rospy.get_param("/motor_controllers/m2/qpps")
self.battery_max_time = rospy.get_param("/battery/max_time")
self.battery_max_volts = rospy.get_param("/battery/max_volts")
self.battery_coef_a = rospy.get_param("/battery/a")
self.battery_coef_b = rospy.get_param("/battery/b")
self.battery_coef_c = rospy.get_param("/battery/c")
self.battery_warning = rospy.get_param("/battery/warning_percent")
self.battery_shutdown = rospy.get_param("/battery/shutdown_percent")
self.rc.SetM1VelocityPID(self.address,m1p, m1i, m1d, m1qpps)
self.rc.SetM2VelocityPID(self.address,m2p, m2i, m2d, m2qpps)
self.rc.WriteNVM(self.address)
time.sleep(0.001)
self.rc.ReadNVM(self.address)
def _lock_thread(self,lock):
'''
Checks the thread lock and then grabs it when it frees up
no return value
'''
if (lock):
start = time.time()
while self._thread_lock:
#rospy.loginfo("in threadlock")
if time.time() - start > self.thread_timeout:
raise Exception("Thread lock timeout")
time.sleep(0.001)
self._thread_lock = True
else:
self._thread_lock = False
def _get_Temp(self):
'''
Gets the temperature of the motor controllers
return:
list [2] (int): Temperature values * 10 degrees C
'''
self._lock_thread(1)
self.temp = self.rc.ReadTemp(self.address)[1]
self._lock_thread(0)
self.temp = int(self.temp*100)/1000.0
return self.temp
def _get_Voltage(self):
'''
Gets the voltage of the motor controllers
return:
voltage (int) : Voltage values * 10 volts
'''
self._lock_thread(1)
v = self.rc.ReadMainBatteryVoltage(self.address)[1]
v = int(v*100)/1000.0
if v != 0:
self.voltage = v + 0.4 #accounts for the voltage drop in the diode
self._lock_thread(0)
return v
def _get_Currents(self):
'''
Gets the current of the motor controllers
return:
list [2] (int): Current values * 100 Amps
'''
self._lock_thread(1)
cur = self.rc.ReadCurrents(self.address)
self._lock_thread(0)
r_current = int(cur[1])/100.0
l_current = int(cur[2])/100.0
self.currents = [l_current,r_current]
self.left_currents.insert(0, l_current)
self.right_currents.insert(0, r_current)
if (len(self.left_currents) > self.rate/2):
del self.left_currents[-1]
del self.right_currents[-1]
left_power = 0
right_power = 0
for i in range(len(self.left_currents)):
left_power += math.pow(self.left_currents[i],2) * self.delta_t
right_power += math.pow(self.right_currents[i],2) * self.delta_t
if (left_power >= math.pow(self.max_current,2) or right_power >= math.pow(self.max_current,2)):
rospy.loginfo("Motor power exceeded max allowed! Disabling motors for %d seconds" %(self.motor_lockout_time))
self.motor_lockout = 1
self.set_estop(1)
self.lockout_timestamp = time.time()
if (self.motor_lockout and (time.time() - self.lockout_timestamp >= self.motor_lockout_time)):
rospy.loginfo("Re-enabling the motors from timeout lock")
self.motor_lockout = 0
self.set_estop(0)
self.left_integrator = left_power
self.right_integrator = right_power
self.max_left_integrator = max(self.max_left_integrator, self.left_integrator)
self.max_right_integrator = max(self.max_right_integrator, self.right_integrator)
#print self.left_integrator, self.right_integrator
return self.currents
def _get_Errors(self):
'''
Gets the error status of the motor controllers
return:
error (int): Error code for motor controller
'''
self._lock_thread(1)
self.error = self.rc.ReadError(self.address)[1]
self._lock_thread(0)
return self.error
def _get_Encs(self):
'''
Gets the encoder values of the motor controllers
return:
list [2] (int): Speed of motors in radians/s, computed at each delta T
'''
self._lock_thread(1)
r_enc = self.rc.ReadEncM1(self.address)[1]
l_enc = self.rc.ReadEncM2(self.address)[1]
dt = datetime.now()
self._lock_thread(0)
if self.prev_tick == [None, None]:
l_vel_rad_s, r_vel_rad_s = 0,0
self.timestamp = 0
else:
delta_t = ((dt-self.prev_enc_ts).microseconds)/1000000.0
self.timestamp = int(self.timestamp + (delta_t * 100000))
l_vel = (l_enc - self.prev_tick[0])/(delta_t)
r_vel = (r_enc - self.prev_tick[1])/(delta_t)
l_vel_rad_s = l_vel * (2 * math.pi/self.tick_per_rev)
r_vel_rad_s = r_vel * (2 * math.pi/self.tick_per_rev)
l_vel_rad_s = int(l_vel_rad_s * 1000)/1000.0
r_vel_rad_s = int(r_vel_rad_s * 1000)/1000.0
self.prev_enc_ts = dt
self.prev_tick = [l_enc, r_enc]
self.enc = [l_vel_rad_s, r_vel_rad_s]
return l_vel_rad_s, r_vel_rad_s
def _send_motor_cmds(self):
l_vel = self._l_vel_cmd_buf
r_vel = self._r_vel_cmd_buf
l_vel *= (self.tick_per_rev/(2*math.pi))
r_vel *= (self.tick_per_rev/(2*math.pi))
l_vel = max(min(l_vel,self.max_cts_per_s), -self.max_cts_per_s)
r_vel = max(min(r_vel,self.max_cts_per_s), -self.max_cts_per_s)
if (( abs(l_vel) <= self.max_cts_per_s) and (abs(r_vel) <= self.max_cts_per_s)):
if not self.motor_lockout:
self._lock_thread(1)
self.rc.SpeedAccelM1(self.address, self.max_accel, int(r_vel))
self.rc.SpeedAccelM2(self.address, self.max_accel, int(l_vel))
self._lock_thread(0)
else:
rospy.loginfo( "values not in accepted range" )
self.send_motor_cmds(0,0)
# Public Methods
def set_estop(self,val):
'''
Sets the E-stop pin to stop Motor control movement until cleared
Parameters:
val (int):
0 - Clears E-stop
1 - Sets E-stop, disabling motor movement
no return value
'''
if (val != self.e_stop):
if val:
rospy.loginfo( "Enabling the E-stop")
GPIO.output(self.e_stop_pin, 1)
self.e_stop = 1
else:
rospy.loginfo( "Clearing the E-stop")
GPIO.output(self.e_stop_pin, 0)
self.e_stop = 0
def battery_state_esimator(self):
x = self.voltage
y = math.pow(x,2) * self.battery_coef_a + self.battery_coef_b * x + self.battery_coef_c
self.battery_percent = (100 * y/float(self.battery_max_time))
if (self.battery_percent <= self.battery_warning):
self.shutdown_warning = True
else:
self.shutdown_warning = False
if (self.battery_percent <= self.battery_shutdown):
self.shutdown_flag = True
self.set_estop(1)
def update_cmd_buf(self, l_vel, r_vel):
'''
Updates the command buffers and sets the flag that new command has been received
Parameters:
l_vel (int): [-0.833, 0.833] units of [rad/s]
r_vel (int): [-0.833, 0.833] units of [rad/s]
no return value
'''
self._l_vel_cmd_buf = l_vel
self._r_vel_cmd_buf = r_vel
self._cmd_buf_flag = 1
def kill_motors(self):
'''
Stops all motors on the assembly
'''
self._lock_thread(1)
self.rc.ForwardM1(self.address, 0)
self.rc.ForwardM2(self.address, 0)
self._lock_thread(0)
def loop(self, counter):
'''
Gets the data from the motor controllers to populate as class variables
all data function classes are private because of threadlocks
Downsample non-critical values to keep serial comm line free
Parameters:
counter (int):
no return value
'''
if (self._cmd_buf_flag):
self._send_motor_cmds()
self._cmd_buf_flag = 0
self._get_Encs()
if not counter % 2:
self._get_Currents()
if not counter % 5:
self._get_Errors()
if not counter % 20:
self._get_Temp()
self._get_Voltage()
self.battery_state_esimator()
def enable_12v_reg(self, en):
'''
Turns on/off the 12V regulator GPIO pin
Parameters:
en (int):
0: Disabled
1: Enabled
'''
try:
if (en != self.reg_enabled):
if en:
rospy.loginfo("Enabling the 12V Regulator")
GPIO.output(self.reg_en_pin, 1)
self.reg_enabled = 1
else:
rospy.loginfo("Disabling the 12V Regulator")
GPIO.output(self.reg_en_pin, 0)
self.reg_enabled = 0
except:
pass
def cleanup(self):
'''
Cleans up the motor controller node, stopping motors and killing all threads
no return value
'''
rospy.loginfo("Cleaning up the motor_controller node..")
self._thread_lock = False
self.kill_motors()
self.set_estop(1)
try:
GPIO.cleanup()
except:
pass
if not sim:
# Initialise the roboclaw motorcontroller
print "Initialising roboclaw driver..."
from roboclaw import Roboclaw
rc = Roboclaw("/dev/roboclaw", 115200)
rc.Open()
rc_address = 0x80
# Get roboclaw version to test if is attached
version = rc.ReadVersion(rc_address)
if version[0] is False:
print "Roboclaw get version failed"
sys.exit()
else:
print repr(version[1])
# Set PID variables to those required by K9
rc.SetM1VelocityPID(rc_address, M1_P, M1_I, M1_D, M1_QPPS)
rc.SetM2VelocityPID(rc_address, M2_P, M2_I, M2_D, M2_QPPS)
# Zero the motor encoders
rc.ResetEncoders(rc_address)
print "PID variables set on roboclaw"
def stop():
'''Lock motors to stop motion
'''
print "Stopping"
if not sim:
rc.SpeedAccelDistanceM1M2(address=rc_address,
accel=int(ACCELERATION),
speed1=0,
distance1=0,
import math
import time
from roboclaw import Roboclaw
rc = Roboclaw("/dev/roboclaw", 115200)
rc.Open()
rc_address = 0x80
m1_qpps = 1570
m2_qpps = 1138
acceleration = 25
speed = 50
distance = 152
# Get roboclaw version to test if is attached
version = rc.ReadVersion(rc_address)
# Set PID variables to those required by K9
rc.SetM1VelocityPID(rc_address, 6.04, 1.55, 0, m1_qpps)
rc.SetM2VelocityPID(rc_address, 6.63, 2.11, 0, m2_qpps)
# Zero the motor encoders
rc.ResetEncoders(rc_address)
def displayspeed():
enc1 = rc.ReadEncM1(rc_address)
enc2 = rc.ReadEncM2(rc_address)
speed1 = rc.ReadSpeedM1(rc_address)
speed2 = rc.ReadSpeedM2(rc_address)
print str(time.time() - base_time) + ",",
if (enc1[0] == 1):
print str(enc1[1]) + ",",
else:
print "failed",
rc.SetConfig(0x80, config) rc.SetPinFunctions(0x80, 2, 0, 0) # S3 = E-Stop, S4 = Disabled, S5 = Disabled rc.WriteNVM(0x80) rc.ReadEncM1(0x80) rc.ResetEncoders(0x80) rc.ReadEncM1(0x80) p = 15000 i = 1000 d = 500 qpps = 3000 rc.SetM1VelocityPID(0x80, p, i, d, qpps) rc.ReadM1VelocityPID(0x80) rc.SpeedM1(0x80, 250) rc.ReadM1MaxCurrent(0x80) rc.ReadCurrents(0x80) error = rc.ReadError(0x80)[1] format(error, "08b") # "Position" API appears to be for times when we want to act like # a servo motor. Probably not applicable here. """ P = 600 I = 0
# This program moves K9 in a circle
import math
from roboclaw import Roboclaw
rc = Roboclaw("/dev/roboclaw", 115200)
rc.Open()
rc_address = 0x80
m1_qpps = 1762
m2_qpps = 1050
acceleration = 100
speed = 500
distance = 300
# Get roboclaw version to test if is attached
version = rc.ReadVersion(rc_address)
# Set PID variables to those required by K9
rc.SetM1VelocityPID(rc_address, 8.55, 2.21, 0, m1_qpps)
rc.SetM2VelocityPID(rc_address, 8.96, 2.82, 0, m2_qpps)
# Zero the motor encoders
rc.ResetEncoders(rc_address)
rc.SpeedAccelDistanceM1M2(address=rc_address,
accel=acceleration,
speed1=int(-speed),
distance1=int(distance),
speed2=int(speed),
distance2=int(distance),
buffer=int(1))
rc.SpeedAccelDistanceM1M2(address=rc_address,
accel=655360,
speed1=int(-1),
distance1=int(distance),
speed2=int(-1),