def toplevel(
#=========
# Clocks
#=========
sys_clk_n,
sys_clk_p,
aux_clk_n,
aux_clk_p,
#========
# GPIOs
#========
gpio, #[15:0]
#===================
# EPB bus from PPC
#===================
ppc_per_clk, # is this the epb clock?
ppc_paddr, #[5:29]
ppc_pcsn, #[1:0]
ppc_pdata, #[0:31]
ppc_pben, #[0:3]
ppc_poen,
ppc_pwrn,
ppc_pblastn,
ppc_prdy,
ppc_doen,
v6_irqn
):
NUM_SLAVES = 2
SYS_BLOCK_SLI = 1
SW_REG_SLI = 2
(sys_rst, sys_clk, sys_clk90,
sys_clk180, sys_clk270, sys_clk_lock,
power_on_rst, sys_clk2x, sys_clk2x90,
sys_clk2x180, sys_clk2x270, aux_clk,
aux_clk90, aux_clk180, aux_clk270,
aux_clk2x, aux_clk2x90, aux_clk2x180,
aux_clk2x270, idelay_rdy) = [Signal(bool(0)) for i in range(20)]
(wbm_clk_i, wbm_rst_i, wbm_cyc_o,
wbm_stb_o, wbm_we_o, wbm_sel_o,
wbm_adr_o, wbm_dat_o, wbm_dat_i,
wbm_ack_i, wbm_err_i, epb_clk,
epb_data_i, epb_data_o, epb_data_oe_n) = [Signal(bool(0)) for i in range(15)]
clk_infr = clk_infrastructure.clk_infrastructure_wrapper(
block_name = "1",
sys_clk_n = sys_clk_n,
sys_clk_p = sys_clk_p,
sys_clk = sys_clk,
sys_clk90 = sys_clk90,
sys_clk180 = sys_clk180,
sys_clk270 = sys_clk270,
sys_clk_lock = sys_clk_lock,
op_power_on_rst = power_on_rst,
sys_clk2x = sys_clk2x,
sys_clk2x90 = sys_clk2x90,
sys_clk2x180 = sys_clk2x180,
sys_clk2x270 = sys_clk2x270,
epb_clk_in = ppc_per_clk,
epb_clk = epb_clk,
aux_clk_n = aux_clk_n,
aux_clk_p = aux_clk_p,
aux_clk = aux_clk,
aux_clk90 = aux_clk90,
aux_clk180 = aux_clk180,
aux_clk270 = aux_clk270,
aux_clk2x = aux_clk2x,
aux_clk2x90 = aux_clk2x90,
aux_clk2x180 = aux_clk2x180,
aux_clk2x270 = aux_clk2x270,
idelay_rst = power_on_rst,
idelay_rdy = idelay_rdy
)
# maybe change clock to slower epb clock
rst_blk = reset_block.reset_block_wrapper(
block_name = "1",
clk = sys_clk,
async_rst_i = power_on_rst,
rst_i = power_on_rst,
rst_o = sys_rst
)
wbm_clk_i = epb_clk
epb_wb_brdg = epb_wb_bridge.epb_wb_bridge_wrapper(
block_name = "1",
wb_clk_i = wbm_clk_i,
wb_rst_i = wbm_rst_i,
wb_cyc_o = wbm_cyc_o,
wb_stb_o = wbm_stb_o,
wb_we_o = wbm_we_o,
wb_sel_o = wbm_sel_o,
wb_adr_o = wbm_adr_o,
wb_dat_o = wbm_dat_o,
wb_dat_i = wbm_dat_i,
wb_ack_i = wbm_ack_i,
wb_err_i = wbm_err_i,
epb_clk = epb_clk,
epb_cs_n = ppc_pcsn,
epb_oe_n = ppc_poen,
epb_r_w_n = ppc_pwrn,
epb_be_n = ppc_pben,
epb_addr = ppc_paddr,
epb_data_o = epb_data_o,
epb_data_i = epb_data_i,
epb_data_oe_n = epb_data_oe_n,
epb_rdy = ppc_prdy,
epb_doen = ppc_doen
)
wbs_we_o, wbs_sel_o, wbs_adr_o, wbs_dat_o = [Signal(bool(0)) for i in range(4)]
#wbs_cyc_o, wbs_stb_o, wbs_ack_i, wbs_err_i = [Signal(intbv(0)[NUM_SLAVES:]) for i in range(4)]
wbs_cyc_o, wbs_stb_o, wbs_ack_i, wbs_err_i = [Signal(intbv(0)[32:]) for i in range(4)]
wbs_dat_i = Signal(intbv(0)[32*NUM_SLAVES:])
epb_infr = epb_infrastructure.epb_infrastructure_wrapper(
block_name = "1",
epb_data_buf = ppc_pdata,
epb_data_oe_n = epb_data_oe_n,
epb_data_i = epb_data_o,
epb_data_o = epb_data_i
)
wbs_arb = wbs_arbiter.wbs_arbiter_wrapper(
block_name = "1",
wb_clk_i = wbm_clk_i,
wb_rst_i = wbm_rst_i,
wbm_cyc_i = wbm_cyc_o,
wbm_stb_i = wbm_stb_o,
wbm_we_i = wbm_we_o,
wbm_sel_i = wbm_sel_o,
wbm_adr_i = wbm_adr_o,
wbm_dat_i = wbm_dat_o,
wbm_dat_o = wbm_dat_i,
wbm_ack_o = wbm_ack_i,
wbm_err_o = wbm_err_i,
wbs_cyc_o = wbs_cyc_o,
wbs_stb_o = wbs_stb_o,
wbs_we_o = wbs_we_o,
wbs_sel_o = wbs_sel_o,
wbs_adr_o = wbs_adr_o,
wbs_dat_o = wbs_dat_o,
wbs_dat_i = wbs_dat_i,
wbs_ack_i = wbs_ack_i
)
sys_blk = sys_block.sys_block_wrapper(
block_name = "1",
wb_clk_i = wbm_clk_i,
wb_rst_i = wbm_rst_i,
wbs_cyc_i = wbs_cyc_o,
wbs_stb_i = wbs_stb_o,
wbs_we_i = wbs_we_o,
wbs_sel_i = wbs_sel_o,
wbs_adr_i = wbs_adr_o,
wbs_dat_i = wbs_dat_o,
wbs_dat_o = wbs_dat_i,
wbs_ack_o = wbs_ack_i,
wbs_err_o = wbs_err_i,
)
user_datai0 = Signal(intbv(0)[8:])
count_out = Signal(intbv(0)[32:])
sr = swr.sw_reg_r()
swreg = sr.sw_reg_r_wrapper(
fabric_clk = sys_clk,
fabric_data_in = count_out,
wbs_clk_i = wbm_clk_i,
wbs_rst_i = wbm_rst_i,
wbs_cyc_i = wbs_cyc_o,
wbs_stb_i = wbs_stb_o,
wbs_we_i = wbs_we_o,
wbs_sel_i = wbs_sel_o,
wbs_adr_i = wbs_adr_o,
wbs_dat_i = wbs_dat_o,
wbs_dat_o = wbs_dat_i,
wbs_ack_o = wbs_ack_i,
wbs_err_o = wbs_err_i,
module_name = 1,
SLI = 2,
BUS_BASE_ADDR = 0,
BUS_HIGH_ADDR = 32,
BUS_DATA_WIDTH = 32,
BUS_ADDR_WIDTH = 1,
BYTE_EN_WIDTH = 4
)
cntr = counter.counter_wrapper(
block_name = "1",
clk = sys_clk,
en = 1,
rst = 0,
out = count_out
)
@always_comb
def logic():
gpio.next = count_out[32:16]
return clk_infr, rst_blk, epb_wb_brdg, epb_infr, wbs_arb, sys_blk, cntr, swreg, logic
def toplevel(
#=========
# Clocks
#=========
sys_clk_n,
sys_clk_p,
aux_clk_n,
aux_clk_p,
#========
# GPIOs
#========
gpio, #[15:0]
#===================
# EPB bus from PPC
#===================
ppc_per_clk,
ppc_paddr, #[5:29]
ppc_pcsn, #[1:0]
ppc_pdata, #[0:31]
ppc_pben, #[0:3]
ppc_poen,
ppc_pwrn,
ppc_pblastn,
ppc_prdy,
ppc_doen,
#==============
# ADC 0 Ports
#==============
# clock
kat_adc0_clk_n,
kat_adc0_clk_p,
kat_adc0_sync_n,
kat_adc0_sync_p,
kat_adc0_overrange_n,
kat_adc0_overrange_p,
# data
kat_adc0_di_d_n, #[7:0]
kat_adc0_di_d_p, #[7:0]
kat_adc0_di_n, #[7:0]
kat_adc0_di_p, #[7:0]
kat_adc0_dq_d_n, #[7:0]
kat_adc0_dq_d_p, #[7:0]
kat_adc0_dq_n, #[7:0]
kat_adc0_dq_p, #[7:0]
# spi interface
kat_adc0_spi_clk,
kat_adc0_spi_data,
kat_adc0_spi_cs,
# iic interface
kat_adc0_iic_sda,
kat_adc0_iic_scl,
v6_irqn
):
NUM_SLAVES = 5
SYS_BLOCK_SLI = 1
SW_REG_SLI = 2
SPI_CONTROLLER_SLI = 3
IIC_CONTROLLER_SLI = 4
BRAM_WB_SLI = 5
(sys_rst, sys_clk, sys_clk90,
sys_clk180, sys_clk270, sys_clk_lock,
power_on_rst, sys_clk2x, sys_clk2x90,
sys_clk2x180, sys_clk2x270, aux_clk,
aux_clk90, aux_clk180, aux_clk270,
aux_clk2x, aux_clk2x90, aux_clk2x180,
aux_clk2x270, idelay_rdy) = [Signal(bool(0)) for i in range(20)]
(wbm_clk_i, wbm_rst_i, wbm_cyc_o,
wbm_stb_o, wbm_we_o, wbm_sel_o,
wbm_adr_o, wbm_dat_o, wbm_dat_i,
wbm_ack_i, wbm_err_i, epb_clk,
epb_data_i, epb_data_o, epb_data_oe_n) = [Signal(bool(0)) for i in range(15)]
clk_inf = clk_infr.clk_infrastructure_wrapper(
block_name = "1",
sys_clk_n = sys_clk_n,
sys_clk_p = sys_clk_p,
sys_clk = sys_clk,
sys_clk90 = sys_clk90,
sys_clk180 = sys_clk180,
sys_clk270 = sys_clk270,
sys_clk_lock = sys_clk_lock,
op_power_on_rst = power_on_rst,
sys_clk2x = sys_clk2x,
sys_clk2x90 = sys_clk2x90,
sys_clk2x180 = sys_clk2x180,
sys_clk2x270 = sys_clk2x270,
epb_clk_in = ppc_per_clk,
epb_clk = epb_clk,
aux_clk_n = aux_clk_n,
aux_clk_p = aux_clk_p,
aux_clk = aux_clk,
aux_clk90 = aux_clk90,
aux_clk180 = aux_clk180,
aux_clk270 = aux_clk270,
aux_clk2x = aux_clk2x,
aux_clk2x90 = aux_clk2x90,
aux_clk2x180 = aux_clk2x180,
aux_clk2x270 = aux_clk2x270,
idelay_rst = power_on_rst,
idelay_rdy = idelay_rdy
)
# maybe change clock to slower epb clock
rst_blk = reset_blk.reset_block_wrapper(
block_name = "1",
clk = sys_clk,
async_rst_i = power_on_rst,
rst_i = power_on_rst,
rst_o = sys_rst
)
wbm_clk_i = epb_clk
epb_wb_brdg = epb_wb_bridge.epb_wb_bridge_wrapper(
block_name = "1",
wb_clk_i = wbm_clk_i,
wb_rst_i = wbm_rst_i,
wb_cyc_o = wbm_cyc_o,
wb_stb_o = wbm_stb_o,
wb_we_o = wbm_we_o,
wb_sel_o = wbm_sel_o,
wb_adr_o = wbm_adr_o,
wb_dat_o = wbm_dat_o,
wb_dat_i = wbm_dat_i,
wb_ack_i = wbm_ack_i,
wb_err_i = wbm_err_i,
epb_clk = epb_clk,
epb_cs_n = ppc_pcsn,
epb_oe_n = ppc_poen,
epb_r_w_n = ppc_pwrn,
epb_be_n = ppc_pben,
epb_addr = ppc_paddr,
epb_data_o = epb_data_o,
epb_data_i = epb_data_i,
epb_data_oe_n = epb_data_oe_n,
epb_rdy = ppc_prdy,
epb_doen = ppc_doen
)
wbs_we_o, wbs_sel_o, wbs_adr_o, wbs_dat_o = [Signal(bool(0)) for i in range(4)]
#wbs_cyc_o, wbs_stb_o, wbs_ack_i, wbs_err_i = [Signal(intbv(0)[NUM_SLAVES:]) for i in range(4)]
wbs_cyc_o, wbs_stb_o, wbs_ack_i, wbs_err_i, = [Signal(intbv(0)[32:]) for i in range(4)]
wbs_dat_i = Signal(intbv(0)[32*NUM_SLAVES:])
epb_in = epb_infr.epb_infrastructure_wrapper(
block_name = "1",
epb_data_buf = ppc_pdata,
epb_data_oe_n = epb_data_oe_n,
epb_data_i = epb_data_o,
epb_data_o = epb_data_i
)
wbs_ar = wbs_arb.wbs_arbiter_wrapper(
block_name = "1",
wb_clk_i = wbm_clk_i,
wb_rst_i = wbm_rst_i,
wbm_cyc_i = wbm_cyc_o,
wbm_stb_i = wbm_stb_o,
wbm_we_i = wbm_we_o,
wbm_sel_i = wbm_sel_o,
wbm_adr_i = wbm_adr_o,
wbm_dat_i = wbm_dat_o,
wbm_dat_o = wbm_dat_i,
wbm_ack_o = wbm_ack_i,
wbm_err_o = wbm_err_i,
wbs_cyc_o = wbs_cyc_o,
wbs_stb_o = wbs_stb_o,
wbs_we_o = wbs_we_o,
wbs_sel_o = wbs_sel_o,
wbs_adr_o = wbs_adr_o,
wbs_dat_o = wbs_dat_o,
wbs_dat_i = wbs_dat_i,
wbs_ack_i = wbs_ack_i
)
sys_bl = sys_blk.sys_block_wrapper(
block_name = "1",
wb_clk_i = wbm_clk_i,
wb_rst_i = wbm_rst_i,
wbs_cyc_i = wbs_cyc_o,
wbs_stb_i = wbs_stb_o,
wbs_we_i = wbs_we_o,
wbs_sel_i = wbs_sel_o,
wbs_adr_i = wbs_adr_o,
wbs_dat_i = wbs_dat_o,
wbs_dat_o = wbs_dat_i,
wbs_ack_o = wbs_ack_i,
wbs_err_o = wbs_err_i
)
(iic_sda_i, iic_sda_o, iic_sda_t,
iic_scl_i, iic_scl_o, iic_scl_t) = [Signal(bool(0)) for i in range(6)]
(kat_adc0_reset, kat_adc0_clk, kat_adc0_clk90_out,
kat_adc0_clk180_out, kat_adc0_clk270_out, kat_adc0_mmcm_locked,
kat_adc0_mmcm_reset, kat_adc0_psclk, kat_adc0_psen,
kat_adc0_psincdec, kat_adc0_psdone) = [Signal(bool(0)) for i in range(11)]
iic_inf = iic_infr.iic_infrastructure_wrapper(
block_name = "1",
sda_i = iic_sda_o,
sda_o = iic_sda_i,
sda_t = iic_sda_t,
scl_i = iic_scl_o,
scl_o = iic_scl_i,
scl_t = iic_scl_t,
sda = kat_adc0_iic_sda,
scl = kat_adc0_iic_scl
)
kat_adc_iic_controller = iic_cont.iic_controller_wrapper(
block_name = "1",
wbs_clk_i = wbm_clk_i,
wbs_rst_i = wbm_rst_i,
wbs_cyc_i = wbs_cyc_o,
wbs_stb_i = wbs_stb_o,
wbs_we_i = wbs_we_o,
wbs_sel_i = wbs_sel_o,
wbs_adr_i = wbs_adr_o,
wbs_dat_i = wbs_dat_o,
wbs_dat_o = wbs_dat_i,
wbs_ack_o = wbs_ack_i,
xfer_done = 0,
sda_i = iic_sda_i,
sda_o = iic_sda_o,
sda_t = iic_sda_t,
scl_i = iic_scl_i,
scl_o = iic_scl_o,
scl_t = iic_scl_t,
app_clk = kat_adc0_clk,
gain_load = 1,
gain_value = 1
)
(kat_adc0_adc_reset,
kat_adc0_mmcm_reset,
kat_adc0_psclk,
kat_adc0_psen,
kat_adc0_psincdec,
kat_adc0_psdone,
kat_adc0_clk) = [Signal(bool(0)) for i in range(7)]
kat_adc_spi_controller = spi_cont.spi_controller_wrapper(
block_name = "1",
wb_clk_i = wbm_clk_i,
wb_rst_i = wbm_rst_i,
wb_cyc_i = wbs_cyc_o,
wb_stb_i = wbs_stb_o,
wb_we_i = wbs_we_o,
wb_sel_i = wbs_sel_o,
wb_adr_i = wbs_adr_o,
wb_dat_i = wbs_dat_o,
wb_dat_o = wbs_dat_i,
wb_ack_o = wbs_ack_i,
adc0_adc3wire_clk = kat_adc0_spi_clk,
adc0_adc3wire_data = kat_adc0_spi_data,
adc0_adc3wire_strobe = kat_adc0_spi_cs,
adc0_adc_reset = kat_adc0_adc_reset,
adc0_mmcm_reset = kat_adc0_mmcm_reset,
adc0_psclk = kat_adc0_psclk,
adc0_psen = kat_adc0_psen,
adc0_psincdec = kat_adc0_psincdec,
adc0_psdone = kat_adc0_psdone,
adc0_clk = kat_adc0_clk,
adc1_adc3wire_clk = Signal(bool(0)), #kat_adc1_spi_clk,
adc1_adc3wire_data = Signal(bool(0)), #kat_adc1_spi_data,
adc1_adc3wire_strobe = Signal(bool(0)), #kat_adc1_spi_cs,
adc1_adc_reset = Signal(bool(0)), #kat_adc1_adc0_reset,
adc1_mmcm_reset = Signal(bool(0)), #kat_adc1_mmcm_reset,
adc1_psclk = Signal(bool(0)), #kat_adc1_psclk,
adc1_psen = Signal(bool(0)), #kat_adc1_psen,
adc1_psincdec = Signal(bool(0)), #kat_adc1_psincdec,
adc1_psdone = Signal(bool(0)), #kat_adc1_psdone,
adc1_clk = Signal(bool(0)), #kat_adc1_clk
)
user_datai0 = Signal(intbv(0)[8:])
kat_adc0 = kat_adc.kat_adc_wrapper(
block_name = "1",
#===================
# external signals
#===================
adc_clk_p = kat_adc0_clk_p,
adc_clk_n = kat_adc0_clk_n,
adc_sync_p = kat_adc0_sync_p,
adc_sync_n = kat_adc0_sync_n,
adc_overrange_p = kat_adc0_overrange_p,
adc_overrange_n = kat_adc0_overrange_n,
adc_rst = Signal(bool(0)),
adc_powerdown = Signal(bool(0)),
adc_di_d_p = kat_adc0_di_d_p,
adc_di_d_n = kat_adc0_di_d_n,
adc_di_p = kat_adc0_di_p,
adc_di_n = kat_adc0_di_n,
adc_dq_d_p = kat_adc0_dq_d_p,
adc_dq_d_n = kat_adc0_dq_d_n,
adc_dq_p = kat_adc0_dq_p,
adc_dq_n = kat_adc0_dq_n,
#====================
# user fabric ports
#====================
user_datai0 = user_datai0,
user_datai1 = Signal(bool(0)),
user_datai2 = Signal(bool(0)),
user_datai3 = Signal(bool(0)),
user_dataq0 = Signal(bool(0)),
user_dataq1 = Signal(bool(0)),
user_dataq2 = Signal(bool(0)),
user_dataq3 = Signal(bool(0)),
user_sync0 = Signal(bool(0)),
user_sync1 = Signal(bool(0)),
user_sync2 = Signal(bool(0)),
user_sync3 = Signal(bool(0)),
user_outofrange0 = Signal(bool(0)),
user_outofrange1 = Signal(bool(0)),
user_data_valid = Signal(bool(0)),
ctrl_reset = kat_adc0_adc_reset,
ctrl_clk_in = kat_adc0_clk,
ctrl_clk_out = kat_adc0_clk,
ctrl_clk90_out = kat_adc0_clk90_out,
ctrl_clk180_out = kat_adc0_clk180_out,
ctrl_clk270_out = kat_adc0_clk270_out,
ctrl_mmcm_locked = kat_adc0_mmcm_locked,
mmcm_reset = kat_adc0_mmcm_reset,
mmcm_psclk = kat_adc0_psclk,
mmcm_psen = kat_adc0_psen,
mmcm_psincdec = kat_adc0_psincdec,
mmcm_psdone = kat_adc0_psdone
)
count_out = Signal(intbv(0)[32:])
#bram = bram_wb.bram_wb()
bram_wrap = bram_wb.bram_wb_wrapper(
block_name = "1",
#===============
# fabric ports
#===============
fabric_clk = kat_adc0_clk,
fabric_rst = sys_rst,
fabric_we = 1,
fabric_addr = count_out,
fabric_data_in = user_datai0,
fabric_data_out = Signal(bool(0)),
#===========
# wb ports
#===========
wbs_clk_i = wbm_clk_i,
wbs_rst_i = wbm_rst_i,
wbs_we_i = wbs_we_o,
wbs_cyc_i = wbs_cyc_o,
wbs_stb_i = wbs_stb_o,
wbs_sel_i = wbs_sel_o,
wbs_adr_i = wbs_adr_o,
wbs_dat_i = wbs_dat_o,
wbs_dat_o = wbs_dat_i,
wbs_ack_o = wbs_ack_i,
BUS_BASE_ADDR = 0,
BUS_HIGH_ADDR = 32,
BUS_DATA_WIDTH = 32,
BUS_ADDR_WIDTH = 16,
BUS_BE_WIDTH = 4
)
#sr = sw_reg_r.sw_reg_r()
swreg = sw_reg_r.sw_reg_r_wrapper(
fabric_clk = kat_adc0_clk,
fabric_data_in = count_out,
wbs_clk_i = wbm_clk_i,
wbs_rst_i = wbm_rst_i,
wbs_cyc_i = wbs_cyc_o,
wbs_stb_i = wbs_stb_o,
wbs_we_i = wbs_we_o,
wbs_sel_i = wbs_sel_o,
wbs_adr_i = wbs_adr_o,
wbs_dat_i = wbs_dat_o,
wbs_dat_o = wbs_dat_i,
wbs_ack_o = wbs_ack_i,
wbs_err_o = wbs_err_i,
module_name = 1,
BUS_BASE_ADDR = 0,
BUS_HIGH_ADDR = 32,
BUS_DATA_WIDTH = 32,
BUS_ADDR_WIDTH = 1,
BYTE_EN_WIDTH = 4
)
cntr = counter.counter_wrapper(
block_name = "1",
clk = sys_clk,
en = 1,
rst = 0,
out = count_out,
DATA_WIDTH = 32,
COUNT_FROM = 0,
COUNT_TO = "32'h10000000",
STEP = 1
)
@always_comb
def logic():
gpio.next = count_out[32:16]
return clk_inf, rst_blk, epb_wb_brdg, epb_in, wbs_ar, sys_bl, cntr, kat_adc0, kat_adc_spi_controller, kat_adc_iic_controller, iic_inf, bram_wrap, swreg, logic
def toplevel(
sys_clk_n,
sys_clk_p,
aux_clk_n,
aux_clk_p,
#aux_synci_n,
#aux_synci_p,
#aux_synco_n,
#aux_synco_p,
gpio, #[15:0]
ppc_per_clk, # is this the epb clock?
ppc_paddr, #[5:29]
ppc_pcsn, #[1:0]
ppc_pdata, #[0:31]
ppc_pben, #[0:3]
ppc_poen,
ppc_pwrn,
ppc_pblastn,
ppc_prdy,
ppc_doen,
v6_irqn
):
sys_rst, sys_clk, sys_clk90, sys_clk180, sys_clk270, sys_clk_lock, power_on_rst, sys_clk2x, sys_clk2x90, sys_clk2x180, sys_clk2x270, aux_clk, aux_clk90, aux_clk180, aux_clk270, aux_clk2x, aux_clk2x90, aux_clk2x180, aux_clk2x270, idelay_rdy = [Signal(bool(0)) for i in range(20)]
wbm_clk_i, wbm_rst_i, wbm_cyc_o, wbm_stb_o, wbm_we_o, wbm_sel_o, wbm_adr_o, wbm_dat_o, wbm_dat_i, wbm_ack_i, wbm_err_i, epb_clk, epb_data_i, epb_data_o, epb_data_oe_n = [Signal(bool(0)) for i in range(15)]
clk_infr = clk_infrastructure.clk_infrastructure_wrapper(
block_name = "1",
sys_clk_n = sys_clk_n,
sys_clk_p = sys_clk_p,
sys_clk = sys_clk,
sys_clk90 = sys_clk90,
sys_clk180 = sys_clk180,
sys_clk270 = sys_clk270,
sys_clk_lock = sys_clk_lock,
op_power_on_rst = power_on_rst,
sys_clk2x = sys_clk2x,
sys_clk2x90 = sys_clk2x90,
sys_clk2x180 = sys_clk2x180,
sys_clk2x270 = sys_clk2x270,
epb_clk_in = ppc_per_clk,
epb_clk = epb_clk,
aux_clk_n = aux_clk_n,
aux_clk_p = aux_clk_p,
aux_clk = aux_clk,
aux_clk90 = aux_clk90,
aux_clk180 = aux_clk180,
aux_clk270 = aux_clk270,
aux_clk2x = aux_clk2x,
aux_clk2x90 = aux_clk2x90,
aux_clk2x180 = aux_clk2x180,
aux_clk2x270 = aux_clk2x270,
idelay_rst = power_on_rst,
idelay_rdy = idelay_rdy
)
# maybe change clock to slower epb clock
rst_blk = reset_block.reset_block_wrapper(
block_name = "1",
clk = sys_clk,
async_rst_i = power_on_rst,
rst_i = power_on_rst,
rst_o = sys_rst
)
wbm_clk_i = epb_clk
epb_wb_brdg = epb_wb_bridge.epb_wb_bridge_wrapper(
block_name = "1",
wb_clk_i = wbm_clk_i,
wb_rst_i = wbm_rst_i,
wb_cyc_o = wbm_cyc_o,
wb_stb_o = wbm_stb_o,
wb_we_o = wbm_we_o,
wb_sel_o = wbm_sel_o,
wb_adr_o = wbm_adr_o,
wb_dat_o = wbm_dat_o,
wb_dat_i = wbm_dat_i,
wb_ack_i = wbm_ack_i,
wb_err_i = wbm_err_i,
epb_clk = epb_clk,
epb_cs_n = ppc_pcsn,
epb_oe_n = ppc_poen,
epb_r_w_n = ppc_pwrn,
epb_be_n = ppc_pben,
epb_addr = ppc_paddr,
epb_data_o = epb_data_o,
epb_data_i = epb_data_i,
epb_data_oe_n = epb_data_oe_n,
epb_rdy = ppc_prdy,
epb_doen = ppc_doen
)
wbs_cyc_o, wbs_stb_o, wbs_we_o, wbs_sel_o, wbs_adr_o, wbs_dat_o, wbs_dat_i, wbs_ack_i, wbs_err_i = [Signal(bool(0)) for i in range(9)]
epb_infr = epb_infrastructure.epb_infrastructure_wrapper(
block_name = "1",
epb_data_buf = ppc_pdata,
epb_data_oe_n = epb_data_oe_n,
epb_data_i = epb_data_i,
epb_data_o = epb_data_o
)
wbs_arb = wbs_arbiter.wbs_arbiter_wrapper(
block_name = "1",
wb_clk_i = wbm_clk_i,
wb_rst_i = wbm_rst_i,
wbm_cyc_i = wbm_cyc_o,
wbm_stb_i = wbm_stb_o,
wbm_we_i = wbm_we_o,
wbm_sel_i = wbm_sel_o,
wbm_adr_i = wbm_adr_o,
wbm_dat_i = wbm_dat_o,
wbm_dat_o = wbm_dat_i,
wbm_ack_o = wbm_ack_i,
wbm_err_o = wbm_err_i,
wbs_cyc_o = wbs_cyc_o,
wbs_stb_o = wbs_stb_o,
wbs_we_o = wbs_we_o,
wbs_sel_o = wbs_sel_o,
wbs_adr_o = wbs_adr_o,
wbs_dat_o = wbs_dat_o,
wbs_dat_i = wbs_dat_i,
wbs_ack_i = wbs_ack_i
)
sys_blk = sys_block.sys_block_wrapper(
block_name = "1",
wb_clk_i = wbm_clk_i,
wb_rst_i = wbm_rst_i,
wb_cyc_i = wbs_cyc_o,
wb_stb_i = wbs_stb_o,
wb_we_i = wbs_we_o,
wb_sel_i = wbs_sel_o,
wb_adr_i = wbs_adr_o,
wb_dat_i = wbs_dat_o,
wb_dat_o = wbs_dat_i,
wb_ack_o = wbs_ack_i,
wb_err_o = wbs_err_i
)
count_out = Signal(intbv(0)[32:])
cntr = counter.counter_wrapper(
block_name = "1",
clk = sys_clk,
en = 1,
rst = 0,
out = count_out
)
@always_comb
def logic():
gpio.next = count_out[32:16]
return clk_infr, rst_blk, epb_wb_brdg, epb_infr, wbs_arb, sys_blk, cntr, logic