def k_value_orifice(pipe_id, orifice_id, orifice_l, q, nu=con.WATER_NU):
"""Calculates the minor loss coefficient of an orifice plate in a
pipe.
Parameters:
pipe_id: Entrance pipe's inner diameter from which fluid flows.
orifice_id: Orifice's inner diameter.
orifice_l: Orifice's length from start to end.
q: Fluid's q rate.
nu: Fluid's dynamic viscosity of the fluid. Default: room
temperature water (1 * 10**-6 * m**2/s)
Returns:
k-value at the orifice.
"""
if orifice_id > pipe_id:
raise ValueError('The orifice\'s inner diameter cannot be larger than'
'that of the entrance pipe.')
re = pc.re_pipe(q, pipe_id, nu) # Entrance pipe's Reynolds number.
orifice_type = _get_orifice_type(orifice_l, orifice_id)
if orifice_type == 'thin':
result = _k_value_thin_sharp_orifice(pipe_id, orifice_id, re)
elif orifice_type == 'thick':
result = _k_value_thick_orifice(pipe_id, orifice_id, orifice_l, re)
elif orifice_type == 'oversize':
result = k_value_reduction(pipe_id, orifice_id, q) \
+ k_value_expansion(orifice_id, pipe_id, q)
return result.to(u.dimensionless)
def k_value_reduction(ent_pipe_id,
exit_pipe_id,
q,
fitting_angle=180,
rounded=False,
nu=con.WATER_NU,
pipe_rough=mats.PVC_PIPE_ROUGH):
"""Calculates the minor loss coefficient (k-value) of a square,
tapered, or rounded reduction in a pipe. Defaults to square.
To use tapered, set angle to something that isn't 180.
To use rounded, set rounded to True.
Parameters:
ent_pipe_id: Entrance pipe's inner diameter from which fluid flows.
exit_pipe_id: Exit pipe's inner diameter to which fluid flows.
q: Fluid's q rate.
fitting_angle: Fitting angle. Default: square (180 degrees).
rounded: Rounded fitting. Default: square (False).
nu: Fluid's dynamic viscosity of the fluid. Default: room
temperature water (1 * 10**-6 * m**2/s)
pipe_rough: Pipe roughness. Default: PVC pipe roughness
Returns:
k-value of reduction.
"""
if ent_pipe_id < exit_pipe_id:
print(
'k_value_reduction: Entrance pipe\'s inner diameter is less than '
'exit pipe\'s inner diameter, using expansion instead.')
return k_value_expansion(ent_pipe_id, exit_pipe_id, q, fitting_angle,
rounded, nu, pipe_rough)
f = pc.fric_pipe(q, ent_pipe_id, nu, pipe_rough) # Darcy friction factor.
re = pc.re_pipe(q, ent_pipe_id, nu) # Entrance pipe's Reynolds number.
fitting_type = _get_fitting_type(fitting_angle, rounded)
if fitting_type == 'square':
result = _k_value_square_reduction(ent_pipe_id, exit_pipe_id, re, f)
elif fitting_type == 'tapered':
result = _k_value_tapered_reduction(ent_pipe_id, exit_pipe_id,
fitting_angle, re, f)
elif fitting_type == 'rounded':
result = _k_value_rounded_reduction(ent_pipe_id, exit_pipe_id, re)
elif fitting_type == 'ambiguous':
raise ValueError('The fitting is ambiguously both tapered and rounded.'
'Please set only either fitting_angle or rounded.')
return result.to(u.dimensionless)
