def txrx_burst(freq, samples):
# Set frequency.
device.tx.frequency = freq
device.rx.frequency = freq - rx_offset
# Setup TX and RX metadata structs.
metadata_tx = ffi.new("struct bladerf_metadata [1]")
metadata_tx[0].flags = bladeRF.BLADERF_META_FLAG_TX_BURST_START | bladeRF.BLADERF_META_FLAG_TX_BURST_END
metadata_rx = ffi.new("struct bladerf_metadata [1]")
metadata_rx[0].flags = 0
# Get current timestamp
current_tx_timestamp = device.tx.timestamp
current_rx_timestamp = device.rx.timestamp
print "Timestamps: TX %d, RX %d" % (current_tx_timestamp, current_rx_timestamp)
# Set scheduled transmit and receive timestamps.
metadata_tx[0].timestamp = current_tx_timestamp + device.tx.sample_rate/20 # 10ms into the future
metadata_rx[0].timestamp = current_rx_timestamp + device.tx.sample_rate/20 # 10ms into the future
# Transmit!
device.tx(num_samples,samples=tx_samples, metadata=metadata_tx, timeout_ms=timeout_ms)
rx_samples = device.rx(num_samples, metadata=metadata_rx, timeout_ms = timeout_ms)
# Wait until all samples have been transmitted.
while(device.tx.timestamp < metadata_tx[0].timestamp + 2*num_samples):
pass
print "RXed %d Samples." % (metadata_rx[0].actual_count)
return bladeRF.samples_to_narray(rx_samples, metadata_rx[0].actual_count)
def rx(device, stream, meta_data, samples, num_samples, user_data):
samples = bladeRF.samples_to_narray(samples, num_samples)
try:
queue.put_nowait(samples)
except Queue.Full:
pass
return stream.next()
def test_device():
device = bladeRF.Device()
device.rx.config(bladeRF.FORMAT_SC16_Q11, 64, 16384, 16, 3500)
device.tx.config(bladeRF.FORMAT_SC16_Q11, 64, 16384, 16, 3500)
device.rx.enabled = True
device.tx.enabled = True
device.rx.frequency = 2**28
assert device.rx.frequency == 2**28
device.rx.bandwidth = 1500000
assert device.rx.bandwidth == 1500000
device.rx.sample_rate = 2**21
assert device.rx.sample_rate == 2**21
device.tx.frequency = 1234000000
assert device.tx.frequency == 1234000000
device.tx.bandwidth = 1500000
assert device.tx.bandwidth == 1500000
device.tx.sample_rate = 2**20
assert device.tx.sample_rate == 2**20
raw = device.rx(1024)
array = bladeRF.samples_to_narray(raw, 1024)
assert len(array) == 1024
samples = bytearray(bladeRF.ffi.buffer(raw))
assert isinstance(samples, bytearray)
assert len(samples) == 4096
device.tx(1024, raw)
def rx(device, stream, meta_data, samples, num_samples, user_data):
if squelch:
samples = bladeRF.samples_to_narray(samples, num_samples)
if bladeRF.squelched(samples, squelch):
return stream.current()
buff = stream.current_as_buffer()
outfile.write(buff)
return stream.next()
def rx(device, stream, meta_data, samples, num_samples, user_data):
if squelch:
samples = bladeRF.samples_to_narray(samples, num_samples)
if bladeRF.squelched(samples, squelch):
return stream.current()
buff = stream.current_as_buffer()
outfile.write(buff)
return stream.next()
def rx(dev, stream, meta_data, samples, num_samples, repeater):
with repeater.samples_available:
if not stream.running:
return
samples = bladeRF.samples_to_narray(samples, num_samples)
if bladeRF.squelched(samples, squelch):
return stream.current()
if repeater.num_filled >= 2 * repeater.num_buffers:
# "RX Overrun encountered, stop advancing
return stream.current()
ret = stream.next()
repeater.num_filled += 1
repeater.samples_available.notify()
return ret
def rx(dev, stream, meta_data, samples, num_samples, repeater):
with repeater.samples_available:
if not stream.running:
return
samples = bladeRF.samples_to_narray(samples, num_samples)
if bladeRF.squelched(samples, squelch):
return stream.current()
if repeater.num_filled >= 2 * repeater.num_buffers:
# "RX Overrun encountered, stop advancing
return stream.current()
ret = stream.next()
repeater.num_filled += 1
repeater.samples_available.notify()
return ret
def update():
global metadata, averaging_buffer
samples = device.rx(buffer_size, metadata=metadata, timeout_ms=timeout_ms)
num_samples = metadata[0].actual_count
metadata[0].timestamp = 0
data = bladeRF.samples_to_narray(samples, num_samples)
data = data[:nFFT]
try:
# For some reason we seem to get a lot of NaNs in our received sample data.
# This is a bit of a hack to avoid allowing any NaN values into our averaging array.
data_fft = np.fft.fftshift(10 * np.log10(np.abs(np.fft.fft(data ** 2.0))))
if not np.isnan(data_fft).any():
averaging_buffer = np.roll(averaging_buffer, 1, axis=0)
averaging_buffer[0] = data_fft
p1_data.setData(p1_freq_range, averaging_buffer.mean(axis=0))
except:
pass