class TestGeneral(unittest.TestCase):
def setUp(self): #run before each test
self.NRP8 = PMr().jav_OpenTest(host)
def tearDown(self): #Run after each test
self.assertEqual(self.NRP8.jav_Error()[0], '0')
self.NRP8.jav_Close()
###############################################################################
### <Test>
###############################################################################
def test_NRP_Gets(self):
self.NRP8.Get_BufferedMeas('ON')
self.NRP8.Get_BufferedMeas('OFF')
self.NRP8.Get_EventStatus()
self.NRP8.Get_Offset()
def test_NRP_List(self):
self.NRP8.Get_AvailableNRP()
def test_NRP_Freq(self):
SetVal = 1e9
self.NRP8.Set_Freq(SetVal)
GetVal = self.NRP8.Get_Freq()
if self.NRP8.connected: self.assertEqual(SetVal, int(GetVal))
def test_NRP_Power(self):
self.NRP8.Set_Freq(6e9) # Set Frequency
self.NRP8.Set_AverageMode(1) # Auto Averaging ON
self.NRP8.Set_Average(10) # Avg Count = 4
self.NRP8.Set_PowerOffset(5)
self.NRP8.Set_PowerOffsetState(1)
self.NRP8.Set_InitImm()
self.NRP8.Set_AverageMode(0) # Auto Averaging OFF
self.NRP8.Set_PowerOffsetState(0)
GetVal = self.NRP8.Get_Average()
GetVal = self.NRP8.Get_Power()
def test_NRPM_Power(self):
self.NRP8.Set_Freq(6e9) # Set Frequency
self.NRP8.Set_AverageMode(1) # Auto Averaging OFF
self.NRP8.Set_Average(10) # Avg Count = 4
self.NRP8.Set_PowerOffset(5)
self.NRP8.Set_PowerOffsetState(1)
self.NRP8.Set_InitImm()
self.NRP8.Set_NRPM_LED(1)
self.NRP8.Set_NRPM_LED(0)
GetVal = self.NRP8.Get_NRPM_PowerAll()
def test_NRP_Trigger(self):
self.NRP8.Set_TriggerAuto(0)
self.NRP8.Set_TriggerCount(10)
self.NRP8.Set_TriggerSource('BUS')
self.NRP8.Set_TriggerAuto(1)
def test_NRP_Send(self):
self.NRP8.Set_BufferSize(12)
#Use the first NRP series NRPxxS which is found
if (True):
NRPxxS.jav_Reset() #Start with a clean state
NRPxxS.Set_AverageMode(0) #Auto Averaging OFF
NRPxxS.Set_Average(4) #Avg Count = 4
if (bUseBUSTrigger): #Select the trigger source
NRPxxS.Set_TriggerSource(
'BUS') #Use '*TRG' to trigger a single physical measurement
else:
NRPxxS.Set_TriggerSource(
'EXT2'
) #We get trigger pulses on the external input (SMB-type connector)
NRPxxS.Set_TriggerAuto(0) #Auto-Trigger OFF
NRPxxS.Set_BufferSize(numMeas) #Buffer size is randomly selected to 17
NRPxxS.Get_BufferedMeas('ON') #Configure a buffered measurement
NRPxxS.Set_TriggerCount(numMeas)
szBuff = NRPxxS.jav_ClrErr #Read out all errors / Clear error queue
NRPxxS.Set_InitImm() #Start a 'single' buffered measurement
#Since 17 trigger-counts have been configured,
#the 'single' buffered measurement, which becomes
#initiated by INIT:IMM, is not over until
#17 physical measurements have been triggered
NRPxxS.write('STAT:OPER:MEAS:NTR 2'
) #The end of a physical measurement can be recognized
NRPxxS.write('STAT:OPER:MEAS:PTR 0'
) #by a transistion to 'NOT MEASURING' which is a
#negative transistion on bit 1