def flushInletTree(deviceNames, inputInlet, vacantInlets, flushTime):
"""
"""
# Close all the inlets AND the tree inlet (make no assumptions)
allInputs = ['hep', 'prot', 'ext2', 'ext1', 'ph', 'na', 'bb', 'w']
vc.closeValves(deviceNames, allInputs + ['in'])
indexes = range(len(allInputs))
indexesInputs = dict(zip(allInputs, indexes))
inputIndex = indexesInputs[inputInlet]
# Get the distance from the inputInlet to the vacantInlet mapped to the vacantInlet ID
vacantInletsOrganized = {}
for inlet in vacantInlets:
vacantInletsOrganized[abs(indexesInputs[inlet] - inputIndex)] = [inlet] # distance->port
vc.openValves(deviceNames, [inputInlet])
# Now from close to far, open the valve and wash for the flushTime
for inlet in sorted(vacantInletsOrganized.keys()):
vc.openValves(deviceNames, vacantInletsOrganized[inlet])
time.sleep(flushTime)
vc.closeValves(deviceNames, vacantInletsOrganized[inlet])
# Close all the inlets AND the tree inlet (again, make no assumptions)
vc.closeValves(deviceNames, [inputInlet])
def performGFPTitration(expObject, deviceName, channelsExposures, channelsExposuresTimecourse,
eGFPInput, bufferInput, numPreEquilibriumSteps = 4, inletTreeFlushTime = 30,
preEquilibrationFlushTime = 600, stepUpEquilibrationTime = 360, eGFPTitrationBindingTimes = [],
scanTime = 90, numTitrationTimepoints = 10):
"""Performs a GFP titration experiment.
Starting State: Chip Patterned, Buttons Down (protected)
Reagent Lines: 1x MOPS reaction buffer (with Zn2+), 3nM or 5nM eGFP+2% BSA
in 1x reaction buffer (200uL is sufficient)
Experimental Description________________________________________
1. Close valving and single scan in GFP (pre-assay background)
2. Pre-equilibrate the chamber walls (saturate with GFP)
- Flow eGFP continuously
- Close eGFP and flow buffer continously
- Single scan in eGFP (post-equilibration, step no.)
- Repeat Nx
3. Control for eGFP Binding from the wall to button
- Close all valves
- Open buttons to allow eGFP binding
- Image kinetically over time
- Close buttons
4. Single scan in GFP (pre-step-up button quant)
5. Titration steps (with imaging time calculations)
- Flow GFP, start imaging (flowSubstrateStartAssay)
- Pre-assay imaging = true (adds about 2min flow time, 10min flow total)
- Kinetic imaging, logarithmically, proportional to titration step number
- Buttons down
- Single scan
6. Post-Titration Buffer Flush and Imaging
_______________________________________________________________
Args:
expObject (eh.ExperimentalHarness): Experimental Harness Object
deviceName (str): deviceName (i.e., 'd1', 'd2', 'd3')
channelsExposures (dict): For final timepoints (endpoints). Dictionary
of channels mapped to exposures (e.g., {'2bf':[50, 500], '1pbp':[100, 200]})
channelsExposureTimecourse (dict): For all timecourses, typically with
reduced exposure times to limit time for assay.
Dictionary of channels mapped to exposures (e.g., {'2bf':[50, 500], '1pbp':[100, 200]})
eGFPInput (str): full name of 5nM eGFP input line (e.g., prot1, ext21, ...)
bufferInput (str): full name of washing buffer input line (e.g., hep1, hep2, ...)
numPreEquilibriumSteps (int): number of wall-binding pre-equilibration
steps to perform
inletTreeFlushTime (int): time (seconds) to perform all inlet tree flushes
preEquilibrationFlushTime (int): time (seconds) to flow eGFP, and then
Buffer, in wall-binding steps
stepUpEquilibrationTime (int): time (seconds) to flow eGFP prior to each
titration binding step
eGFPTitrationBindingTimes (list): list of total times to bind, in temporal order
scanTime (int): estimated length of a set of scans for channelsExposures
numTitrationTimepoints (int): number of kinetic timepoints to obtain for
each eGFP binding titration step, spanning time given in eGFPTitrationBindingTimes
Returns:
None
"""
inputs = {'hep', 'prot', 'ext2', 'ext1', 'ph', 'na', 'bb', 'w'}
if eGFPInput not in inputs or bufferInput not in inputs:
raise ValueError('Port name(s) incorrectly specified. The eGFP and Buffer Input Ports must be specified without a trailing device number')
eh.scriptlogger.critical('Starting eGFP Titration in 10s')
time.sleep(10) # A safety in case you notice something wrong
# 1. Close valving, scan GFP
eh.scriptlogger.info('1/6. Started Assay. Preparing Valve States and Background Imaging')
eh.scriptlogger.info(
'GFP Input: {}, Buffer Input: {}, Channels & Exposures: {}, Pre-Equilibration Steps: {}, Titration Steps: {}'.format(
eGFPInput,
bufferInput,
channelsExposures,
numPreEquilibriumSteps,
len(eGFPTitrationBindingTimes))
)
vc.returnToSafeState([deviceName])
ic.scan(expObject.rootPath,
channelsExposures,
deviceName,
'PreAssay ButtonQuant',
eh.posLists[deviceName],
wrappingFolder = True)
eh.scriptlogger.info('Completed Pre-Imaging')
# 2. Pre-equilibration of chamber walls
eh.scriptlogger.info('2/6. Started Wall Pre-Equilibration')
vc.openValves([deviceName], ['s1', 's2', 'out'])
for step in range(numPreEquilibriumSteps):
eh.scriptlogger.warning('Started eGFP/Buffer Pre-Equilibration Cycle {} of {}, {}s \
Cycle Time'.format(step+1, numPreEquilibriumSteps, preEquilibrationFlushTime*2))
vc.openValves([deviceName], [eGFPInput, 'in'])
time.sleep(preEquilibrationFlushTime)
vc.closeValves([deviceName], [eGFPInput])
vc.openValves([deviceName], [bufferInput])
time.sleep(preEquilibrationFlushTime)
ic.scan(expObject.rootPath, channelsExposures, deviceName, 'PostPreEquilibrationBinding Step {}'.format(step+1), eh.posLists[deviceName], wrappingFolder = True)
vc.closeValves([deviceName], [bufferInput])
eh.scriptlogger.warning('Completed Pre-Equilibration Cycle {} of {}'.format(step+1, numPreEquilibriumSteps))
eh.scriptlogger.info('Completed Wall Pre-Equilibration')
# 3. eGFP from wall to button control (timecourse, ~20min)
eh.scriptlogger.info('3/6. Started Wall to Button Control')
vc.returnToSafeState([deviceName])
wallToButtonTimings = {}
wallToButtonTimings['fromWallsControl'] = makeAssayTimings(numLinearPoints = 5,
totalPoints = 8,
scanTime = scanTime,
totalTime = 1200)
expObject.addAssayTimings(wallToButtonTimings)
fromButtonsToWalls = ic.KineticAcquisition(deviceName,
channelsExposuresTimecourse,
expObject.assayTimes['fromWallsControl'],
'Kinetics ButtonstoWallsControl ButtonsUp')
vc.openValves([deviceName], ['b1', 'b2'])
fromButtonsToWalls.startAssay(expObject.rootPath, eh.posLists[deviceName])
vc.closeValves([deviceName], ['b1', 'b2'])
eh.scriptlogger.info('Completed Wall to Button Control')
# 4. Pre-Step-Up Imaging (Buttons Down)
eh.scriptlogger.info('4/6. Started Pre-Step-Up Quantifications')
ic.scan(expObject.rootPath, channelsExposures, deviceName, 'PreStepUp ButtonQuant ButtonsDown',
eh.posLists[deviceName], wrappingFolder = True)
eh.scriptlogger.info('Completed Pre-Step-Up Quantifications')
# 5. eGFP Titration Steps
eGFPTitrationTimings = {}
eGFPTitrationTimingsKeys = []
for step, bindingTime in enumerate(eGFPTitrationBindingTimes):
timingsName = 'eGFPBindingStep{}Times'.format(step)
eGFPTitrationTimingsKeys.append(timingsName)
eGFPTitrationTimings[timingsName] = makeAssayTimings(numLinearPoints = 0,
totalPoints = numTitrationTimepoints,
scanTime = scanTime,
totalTime = bindingTime)
expObject.addAssayTimings(eGFPTitrationTimings)
eh.scriptlogger.info('5/6. Started eGFP Titration Step-Up')
for step, stepTimingsName in enumerate(eGFPTitrationTimingsKeys):
w = 'Started GFP Binding Step {} of {}'.format(step+1, len(eGFPTitrationTimingsKeys))
i = 'Titration Step {}, Timings: {}'.format(stepTimingsName, expObject.assayTimes[stepTimingsName])
eh.scriptlogger.warning(w)
eh.scriptlogger.info(i)
description = 'Kinetics eGFPTitrationBindingStep {}'.format(step+1)
ka = ic.KineticAcquisition(deviceName,
channelsExposuresTimecourse,
expObject.assayTimes[stepTimingsName],
description)
flowSubstrateStartAssay(deviceName,
eGFPInput+deviceName[-1],
ka,
equilibrationTime = stepUpEquilibrationTime,
treeFlushTime = 10,
postEquilibrationImaging = True,
performImaging = True,
postEquilibImageChanExp = channelsExposures)
vc.closeValves([deviceName], ['b1', 'b2'])
ic.scan(expObject.rootPath,
channelsExposures,
deviceName,
'PosteGFPTitrationBindingStep {} ButtonsDown'.format(step+1),
eh.posLists[deviceName],
wrappingFolder = True)
eh.scriptlogger.warning('Completed GFP Binding Step {} of {}'.format(step+1, len(eGFPTitrationTimingsKeys)))
#6. Post-Titration Washout and Imaging. Leave Under Positive Pressure
eh.scriptlogger.info('6/6. Started Buffer Flush and Final Imaging')
vc.returnToSafeState([deviceName])
vc.openValves([deviceName], [bufferInput, 'w'])
time.sleep(inletTreeFlushTime)
vc.closeValves([deviceName], ['w'])
vc.openValves([deviceName], ['in', 's1', 's2', 'out'])
time.sleep(stepUpEquilibrationTime)
vc.returnToSafeState([deviceName])
ic.scan(expObject.rootPath,
channelsExposures,
deviceName,
'PostTitration PostWash ButtonsDown',
eh.posLists[deviceName],
wrappingFolder = True)
vc.openValves([deviceName], [bufferInput, 'in', 's1', 's2'])
eh.scriptlogger.info('Completed eGFP Titration Experiment')
def flowSubstratesStartConcurrentAssays(deviceNames, substrateInputs, KineticAcquisitions, data_dir, pos_lists,
equilibrationTime = 480, treeFlushTime = 20):
"""Concurrently executes two assays
Assays are riffled, but executed concurrently, and with the same timepoints.
Best for use in control assays for multiple devices.
Rev. 103017, DM
Args:
deviceNames (list): names of devices for which to run assays, in
numerical device order (e.g., ['d1', 'd2'])
substrateInputs (list): names of input lines (NOT CONTAINING THE
TRAILING DEVICE NUMBER) containing substrates to assay, in
numerical device order (e.g., [prot, ext1])
KineticAcquisitions (list): list of KineticAcquisition objects
containing acquisition parameters. Note that 'd1' KineticAcquisition
timings will be used to drive both devices
data_dir (str): path of root data directory
pos_lists (list): list of device-specific position lists, in
numerical device order (e.g., [posLists['d1'], posLists['d2']])
equilibrationTime (int): time to flow substrate through device before
assay start (s)
treeFlushTime (int): time to flow substrate through inlet tree before
device equilibration (s)
Returns:
None
"""
eh.scriptlogger.info('**Flowing substrate, starting concurrent for devices \
{} in lines {}'.format(str(deviceNames), str(substrateInputs)))
# Flush the inlet trees
eh.scriptlogger.info('The inlet tree wash started for substrates in ' + str(substrateInputs))
# Close Everything
vc.returnToSafeState(deviceNames)
# vc.openValves(deviceNames, ['hep', 'b1', 'b2'])
vc.open('chip', substrateInputs[0])
vc.open('chip', substrateInputs[1])
vc.openValves(deviceNames, ['w'])
time.sleep(treeFlushTime)
eh.scriptlogger.info('The inlet tree wash done for substrates in ' + str(substrateInputs))
#Expose chips to substrate, equilibrate for equilibrationTime
eh.scriptlogger.info('Chip equilibration started for substrates in ' + str(substrateInputs))
vc.closeValves(deviceNames, ['w'])
vc.openValves(deviceNames, ['in'])
vc.openValves(deviceNames, ['out'])
vc.openValves(deviceNames, ['s1, s2']) # Open both device sandwiches
time.sleep(equilibrationTime)
eh.scriptlogger.info('Chip equilibration done for substrates in ' + str(substrateInputs))
#Close d1 input, inlet tree, outlet, and sandwiches (for d1 only1!!)
vc.close('chip', substrateInputs[0])
vc.closeValves([deviceNames[0]], ['in'])
vc.closeValves([deviceNames[0]], ['out'])
vc.closeValves([deviceNames[0]], ['s1', 's2'])
# Name the kinetic acquisitions and directories
d1Kinetics = KineticAcquisitions[0]
d2Kinetics = KineticAcquisitions[1]
d1KineticSubfolder = '{}_{}_{}'.format('d1',
time.strftime("%Y%m%d_%H%M%S", time.localtime()),
d1Kinetics.note.replace(" ", "_"))
d2KineticSubfolder = '{}_{}_{}'.format('d2',
time.strftime("%Y%m%d_%H%M%S", time.localtime()),
d2Kinetics.note.replace(" ", "_"))
d1kineticDirectory = os.path.join(data_dir, d1KineticSubfolder)
d2kineticDirectory = os.path.join(data_dir, d2KineticSubfolder)
os.makedirs(d1kineticDirectory)
os.makedirs(d2kineticDirectory)
eh.scriptlogger.info('Concurrent Kinetic Acquisitions Started: '
+ str(d1Kinetics.note.replace(" ", "_"))
+ ' & '
+ str(d2Kinetics.note.replace(" ", "_")))
#Open d1 buttons only
vc.openValves([deviceNames[0]], ['b1', 'b2'])
scanIndex = 0
d1ScanQueue = Queue()
d2ScanQueue = Queue()
map(lambda k: d1ScanQueue.put(k), d1Kinetics.delayTimes)
map(lambda k: d2ScanQueue.put(k), d2Kinetics.delayTimes)
lastScanTime = time.time()
while not d1ScanQueue.empty():
nextScanDelay = d1ScanQueue.get() # Dequeue the next scan
deltaTime = (nextScanDelay + lastScanTime) - time.time()
# If too much elapsed time on previous scans, scan right away
if deltaTime <= 0:
# For the first scan, scan d1, then change d2 valve states to start the
# reaction on d2, then scan d2 immediately
if scanIndex == 0:
lastScanTime = time.time()
ic.scan(d1kineticDirectory,
d1Kinetics.channelsExposures,
d1Kinetics.device,
d1Kinetics.note.replace(" ", "_"),
pos_lists[0],
wrappingFolder = True)
vc.close('chip', substrateInputs[1])
vc.closeValves([deviceNames[1]], ['in'])
vc.closeValves([deviceNames[1]], ['out'])
vc.closeValves([deviceNames[1]], ['s1', 's2'])
vc.openValves([deviceNames[1]], ['b1', 'b2'])
ic.scan(d2kineticDirectory,
d2Kinetics.channelsExposures,
d2Kinetics.device,
d2Kinetics.note.replace(" ", "_"),
pos_lists[1],
wrappingFolder = True)
scanIndex+=1
else:
lastScanTime = time.time()
ic.scan(d1kineticDirectory,
d1Kinetics.channelsExposures,
d1Kinetics.device,
d1Kinetics.note.replace(" ", "_"),
pos_lists[0],
wrappingFolder = True)
ic.scan(d2kineticDirectory,
d2Kinetics.channelsExposures,
d2Kinetics.device,
d2Kinetics.note.replace(" ", "_"),
pos_lists[1],
wrappingFolder = True)
# If you have time to spare, wait, then proceed
else:
time.sleep(deltaTime)
if scanIndex == 0:
lastScanTime = time.time()
ic.scan(d1kineticDirectory,
d1Kinetics.channelsExposures,
d1Kinetics.device,
d1Kinetics.note.replace(" ", "_"),
pos_lists[0],
wrappingFolder = True)
vc.close('chip', substrateInputs[1])
vc.closeValves([deviceNames[1]], ['in'])
vc.closeValves([deviceNames[1]], ['out'])
vc.closeValves([deviceNames[1]], ['s1', 's2'])
vc.openValves([deviceNames[1]], ['b1', 'b2'])
ic.scan(d2kineticDirectory,
d2Kinetics.channelsExposures,
d2Kinetics.device,
d2Kinetics.note.replace(" ", "_"),
pos_lists[1],
wrappingFolder = True)
scanIndex+=1
else:
lastScanTime = time.time()
ic.scan(d1kineticDirectory,
d1Kinetics.channelsExposures,
d1Kinetics.device,
d1Kinetics.note.replace(" ", "_"),
pos_lists[0],
wrappingFolder = True)
ic.scan(d2kineticDirectory,
d2Kinetics.channelsExposures,
d2Kinetics.device,
d2Kinetics.note.replace(" ", "_"),
pos_lists[1],
wrappingFolder = True)
eh.scriptlogger.info('Concurrent Kinetic Read Complete')
def patternDevices(devices, inletNames = None, blocknames = None):
"""Performs device surface patterning
Performs patterning on passed list of devices assuming standard input line
configuration (bBSA in 'bb', NeutrAvidin in 'NA', antibody in 'pHis', and
PBS in 'Hepes'). Be sure to attach a "waste tail" to the device, and open
all lines to pressure before executing.
Custom inlet names should be of the form {'na': [na_renamed], 'ph':
[ph_renamed], 'bb': [bb_renamed], 'hep': [bb_renamed], 'w': [w_renamed]}
Custom blocknames should be of the form ['bn1', 'bn2', 'bn3',..., 'bnn']
Blocks opening/closing will occur with inlet opening/closing
Args:
devices (list): list of devices to be patterned, lowercase (e.g.
['d1', 'd2', and 'd3'])
inletNames (dict): remapped inlet names containing precisely {'w':[
w_renamed], 'na': [na_renamed], 'ph': [ph_renamed],
'bb': [bb_renamed], 'hep': [bb_renamed]}. Should not contain trailing index.
blocknames (list): block control valve names of the form ['c1', 'c2', ..., 'c3'].
Valvenames should not containing trailing device index.
Returns:
None
"""
wasteValve = ['w']
buttonValves = ['b1', 'b2']
sandwichValves = ['s1', 's2']
inletValve = ['in']
outlet = ['out']
wasteValve = ['w']
naValve = ['na']
antibodyValve = ['ph']
bbsaValve = ['bb']
bufferValve = ['hep']
if inletNames:
wasteValve = inletNames['w']
naValve = inletNames['na']
antibodyValve = inletNames['ph']
bbsaValve = inletNames['bb']
bufferValve = inletNames['hep']
if blocknames:
inletValve = inletValve + blocknames
vc.returnToSafeState(devices) # Closing all valves
eh.scriptlogger.info('>> 1/18. Starting Device Patterning for devices {}. \
Starting with all valves closed. NOTE: flow of non-biotinylated BSA \
should have already been done'.format(devices))
eh.scriptlogger.info('2/18. Opening sandwiches, outlet, bBSA inlet, and waste. \
Flushing bBSA through inlet tree to waste for 30s')
vc.openValves(devices, sandwichValves + outlet + bbsaValve + wasteValve)
time.sleep(30)
eh.scriptlogger.info('3/18. Done Flushing bBSA to waste. Flushing bBSA through \
devices with buttons closed for 5min')
vc.closeValves(devices, wasteValve)
vc.openValves(devices, inletValve)
time.sleep(300)
eh.scriptlogger.info('4/18. Opened buttons with bBSA flowing through devices to waste for 35min')
vc.openValves(devices, buttonValves)
time.sleep(2100)
eh.scriptlogger.info('5/18. Done Flowing bBSA through devices and closed inlet. \
Flushing PBS through inlet tree to waste for 30s')
vc.closeValves(devices, bbsaValve + inletValve)
vc.openValves(devices, bufferValve + wasteValve)
time.sleep(30)
eh.scriptlogger.info('6/18. Done flowing PBS to waste. Flushing PBS through device \
with buttons open for 10min')
vc.closeValves(devices, wasteValve)
vc.openValves(devices, inletValve)
time.sleep(600)
eh.scriptlogger.info('7/18. Done flushing PBS through devices. \
Flowing neutravidin through inlet tree to waste for 30s')
vc.closeValves(devices, bufferValve + inletValve)
vc.openValves(devices, naValve + wasteValve)
time.sleep(30)
eh.scriptlogger.info('8/18. Done flushing Neutravidin to waste. \
Flowing Neutravidin through devices with buttons open for 30min')
vc.closeValves(devices, wasteValve)
vc.openValves(devices, inletValve)
time.sleep(1800)
eh.scriptlogger.info('9/18. Done flowing Neutravidin through devices. \
Flowing PBS through devices with buttons open for 10min')
vc.closeValves(devices, naValve)
vc.openValves(devices, bufferValve)
time.sleep(600)
eh.scriptlogger.info('10/18. Done flowing PBS through devices and closed buttons. \
Flowing bBSA through the device for another 35min (quench walls only)')
vc.closeValves(devices, bufferValve + buttonValves)
vc.openValves(devices, bbsaValve)
time.sleep(2100)
eh.scriptlogger.info('11/18. Done flowing bBSA through devices. \
Flowing PBS through the device for 10min. **NEXT STEP IS ANTIBODY FLOWING**')
vc.closeValves(devices, bbsaValve)
vc.openValves(devices, bufferValve)
time.sleep(600)
eh.scriptlogger.info('12/18. Done flowing PBS through devices and closed inlet. \
Flowing Antibody through inlet tree to waste for 30s')
vc.closeValves(devices, bufferValve + inletValve)
vc.openValves(devices, antibodyValve + wasteValve)
time.sleep(30)
eh.scriptlogger.info('13/18. Done flowing Antibody through inlet tree. Flowing \
Antibody through device for 2min')
vc.closeValves(devices, wasteValve)
vc.openValves(devices, inletValve)
time.sleep(120)
eh.scriptlogger.info('14/18. While flowing Antibody through devices, opened buttons. \
Flowing for 13.3min')
vc.openValves(devices, buttonValves)
time.sleep(800)
eh.scriptlogger.info('15/18. Closed buttons while flowing Antibody through device for 30s')
vc.closeValves(devices, buttonValves)
time.sleep(30)
eh.scriptlogger.info('16/18. Done flowing Antibody through device. Flowing PBS through \
inlet tree to waste for 30s')
vc.closeValves(devices, antibodyValve + inletValve)
vc.openValves(devices, bufferValve + wasteValve)
time.sleep(30)
eh.scriptlogger.info('17/18. Done flowing PBS to waste. Flowing PBS through device for 10min')
vc.closeValves(devices, wasteValve)
vc.openValves(devices, inletValve)
time.sleep(600)
eh.scriptlogger.info('18/18. Closed the outlets')
vc.closeValves(devices, outlet)
eh.scriptlogger.info('>> Done with device patterning')
def flowSubstrateStartAssay(deviceName, substrateInput, KineticAcquisition,
equilibrationTime = 600, treeFlushTime = 20, postEquilibrationImaging = False,
performImaging = True, postEquilibImageChanExp = {'4egfp':[500]}, scanQueueFlag = False):
"""Performs a standard enzyme turnover assay.
Flows substrate, exposes buttons and closes sandwiches,
performs imaging at specified timesteps
Rev. 102817, DM
Args:
substrateInput (str): valve name of input
deviceName (str): name of device
equilibrationTime (int): time to flush device before assay
Returns:
None
"""
sendToQueue = scanQueueFlag
inputValve = substrateInput[:-1]
eh.scriptlogger.info('>> Flowing substrate, starting assay for \
device {} in lines {}'.format(deviceName, str(substrateInput)))
deviceNumber = str(deviceName[-1])
#Flush the inlet tree
eh.scriptlogger.info('The inlet tree wash started for substrate in ' + str(substrateInput))
vc.returnToSafeState([deviceName])
vc.openValves([deviceName], [inputValve, 'w'])
time.sleep(treeFlushTime)
eh.scriptlogger.info('The inlet tree wash done for substrate in ' + str(substrateInput))
#Expose chip to substrate, equilibrate for equilibrationTime
eh.scriptlogger.info('Chip equilibration started for substrate in ' + str(substrateInput))
if inputValve == 'w': #For the instance where the waste line is the input
pass
else:
vc.closeValves([deviceName], ['w'])
vc.openValves([deviceName], ['in', 'out', 's1', 's2'])
time.sleep(equilibrationTime)
eh.scriptlogger.info('Chip equilibration done for substrate in ' + str(substrateInput))
if postEquilibrationImaging:
if sendToQueue == True:
args = [eh.rootPath,
postEquilibImageChanExp,
deviceName,
KineticAcquisition.note.replace(" ", "_")+'_PreAssay_ButtonQuant',
eh.posLists[deviceName]]
kwargs = {wrappingFolder: True}
ic.hardwareQueue.put((args, kwargs))
else:
ic.scan(eh.rootPath,
postEquilibImageChanExp,
deviceName,
KineticAcquisition.note.replace(" ", "_")+'_PreAssay_ButtonQuant',
eh.posLists[deviceName],
wrappingFolder = True)
#Close things to prep for assay, and open buttons
vc.closeValves([deviceName], [substrateInput[:-1], 'in', 'out', 's1', 's2'])
time.sleep(0.5)
vc.openValves([deviceName], ['b1', 'b2'])
#Start the assay
if performImaging:
KineticAcquisition.startAssay(eh.rootPath,
eh.posLists[deviceName],
scanQueueFlag = sendToQueue)
def performSDSWash(deviceNames, channelsExposures, sdsInputLines, bufferInputLines):
"""SDS pH 6.0 MES wash
Standard protocol of four 5-minute pulses with 10-min post-pulse recovery.
Do not inlcude trailing device nuymber in input line names
Protocol Time: ~1.0h,
Rev. 102817, DM
Args:
deviceNames (list): list of devices for which to perform SDS washes
(e.g., ['d1', 'd2', 'd3'])
channelsExposures (dict): Dictionary of channels mapped to exposures
(e.g., {'2bf':[50, 500], '1pbp':[100, 200]})
sdsInputLines (list): names of SDS input ports (without trailing device number)
bufferInputLines (list): names of buffer input ports (without trailing device number)
Returns:
None
"""
deviceNumbers = [d[1:] for d in deviceNames]
sdsInputs = ["{}{}".format(b, a) for a, b in zip(deviceNumbers, sdsInputLines)]
mopsLines = ["{}{}".format(b, a) for a, b in zip(deviceNumbers, bufferInputLines)]
startMessage = 'SDS Washes Started for Devices {}'.format(str(deviceNames))
eh.scriptlogger.info(startMessage)
try:
vc.returnToSafeState(deviceNames)
for washNumber in range(1, 5):
washStartMessage = 'SDS Wash Number {} Started for devices {}'.format(washNumber, str(deviceNames))
eh.scriptlogger.info(washStartMessage)
time.sleep(0.5)
vc.openValves(deviceNames, ['s1', 's2']) #Open sandwiches, bring to start state
map(lambda v: vc.open('chip', v), sdsInputs) #Open SDS Inputs
vc.openValves(deviceNames, ['w']) #Open the Wastes
time.sleep(10)
vc.closeValves(deviceNames, ['w']) #Close the Wastes
vc.openValves(deviceNames, ['in']) #Open Tree Inputs, Start SDS Flowing
vc.openValves(deviceNames, ['out']) #Open Outlets, Start SDS Flowing
time.sleep(300)
vc.closeValves(deviceNames, ['in']) # Close inlet tree to stop flow
map(lambda v: vc.close('chip', v), sdsInputs) # Close the SDS input lines
map(lambda v: vc.open('chip', v), mopsLines) # Open Buffer Port
vc.openValves(deviceNames, ['w']) # Open the waste to flush inlet tree
time.sleep(10)
vc.closeValves(deviceNames, ['w']) # Close the waste to stop inlet tree flush
vc.openValves(deviceNames, ['in']) # Open the inlet tree to flush devices
time.sleep(600)
vc.returnToSafeState(deviceNames) # Close everything in preparation for next cycle
washEndMessage = 'SDS Wash Number {} Ended for devices {}'.format(washNumber, str(deviceNames))
eh.scriptlogger.info(washEndMessage)
except Exception:
eh.scriptlogger.warning('The SDS Wash Failed with an Exception! Closing all valves')
vc.returnToSafeState(deviceNames)
endMessage = 'SDS Washes Ended for Devices {}'.format(str(deviceNames))
eh.scriptlogger.info(startMessage)
vc.returnToSafeState(deviceNames)