def changePara():
write = ['N/A'] * 4
d = 0
write[0] = LRL_roll.get()
write[1] = URL_roll.get()
if int(write[0]) > int(write[1]):
tkinter.messagebox.showerror(
'Error',
'Lower Rate Limit cannot be bigger than Upper Rate Limit')
else:
write[2] = AA_roll.get()
aoo_aa_p = AA_roll.get()
if aoo_aa_p == 'OFF':
aoo_aa_p = 0
else:
aoo_aa_p = int(100 * float(aoo_aa_p))
write[3] = APW_roll.get()
if checkConnect() == 6:
connectLable.set("No Pacemaker Connected")
label = tk.Label(root_AOO,
textvariable=connectLable,
font=("Times New Roman", 14),
fg="red").place(x=10, y=40)
label = tk.Label(paraWindow,
textvariable=connectLable,
font=("Times New Roman", 14),
fg="red").place(x=10, y=40)
tkinter.messagebox.showerror(
'Error', 'Failed to connect to the Pacemaker')
else:
connectLable.set("Pacemaker is Connected")
label = tk.Label(root_AOO,
textvariable=connectLable,
font=("Times New Roman", 14),
fg="green").place(x=10, y=40)
label = tk.Label(paraWindow,
textvariable=connectLable,
font=("Times New Roman", 14),
fg="green").place(x=10, y=40)
writePara(mode=1,
Lower_Rate=int(LRL_roll.get()),
ATR_Amplitude=int(aoo_aa_p),
ATR_Width=int(APW_roll.get()))
with open("parameterAOO.txt", "w") as parameterFile:
while (d < 4):
parameterFile.write(
write[d] +
"\n") #Write every index of list write[] into file
d += 1
d = 0
lrlLabel.set(write[0])
urlLabel.set(write[1])
aaLabel.set(write[2])
apwLabel.set(write[3])
paraWindow.destroy()
def changePara():
write = ['N/A'] * 13
p = 0
write[0] = LRL_roll.get()
write[1] = URL_roll.get()
if int(write[0]) > int(write[1]):
tkinter.messagebox.showerror(
'Error',
'Lower Rate Limit cannot be bigger than Upper Rate Limit')
else:
write[2] = AA_roll.get()
aair_aa_p = AA_roll.get()
if aair_aa_p == 'OFF':
aair_aa_p = 0
else:
aair_aa_p = int(100 * float(aair_aa_p))
write[3] = APW_roll.get()
write[4] = MSR_roll.get()
write[5] = AT_roll.get()
aair_at_p = AT_roll.get()
if aair_at_p == 'V-Low':
aair_at_p = 0.5
elif aair_at_p == 'Low':
aair_at_p = 1.0
elif aair_at_p == 'Med-Low':
aair_at_p = 1.5
elif aair_at_p == 'Med':
aair_at_p = 1.75
elif aair_at_p == 'Med-High':
aair_at_p = 2.0
elif aair_at_p == 'High':
aair_at_p = 2.5
elif aair_at_p == 'V_High':
aair_at_p = 3.0
write[6] = REAC_roll.get()
aair_reac_p = REAC_roll.get()
if aair_reac_p == '5(Test)':
aair_reac_p = 5
write[7] = RF_roll.get()
write[8] = RECO_roll.get()
aair_reco_p = RECO_roll.get()
if aair_reco_p == '0.1(Test)':
aair_reco_p = 6
else:
aair_reco_p = 60 * int(aair_reco_p)
write[9] = AS_roll.get()
write[10] = ARP_roll.get()
write[11] = PVARP_roll.get()
write[12] = RS_roll.get()
if checkConnect() == 6:
connectLable.set("No Pacemaker Connected")
label = tk.Label(root_AAIR,
textvariable=connectLable,
font=("Times New Roman", 14),
fg="red").place(x=10, y=40)
label = tk.Label(paraWindow,
textvariable=connectLable,
font=("Times New Roman", 14),
fg="red").place(x=10, y=40)
tkinter.messagebox.showerror(
'Error', 'Failed to connect to the Pacemaker')
else:
connectLable.set("Pacemaker is Connected")
label = tk.Label(root_AAIR,
textvariable=connectLable,
font=("Times New Roman", 14),
fg="green").place(x=10, y=40)
label = tk.Label(paraWindow,
textvariable=connectLable,
font=("Times New Roman", 14),
fg="green").place(x=10, y=40)
writePara(mode = 9, Lower_Rate = int(LRL_roll.get()), MSR = int(MSR_roll.get()), ATR_Amplitude = int(aair_aa_p), ATR_Width = int(APW_roll.get()), \
ATR_Refractory = int(ARP_roll.get()), Activity_Threshold = aair_at_p, Reaction_Time = int(aair_reac_p), Response_Factor = int(RF_roll.get()), \
Recovery_Time = int(aair_reco_p))
with open("parameterAAIR.txt", "w") as parameterFile:
while (p < 13):
parameterFile.write(
write[p] +
"\n") #Write every index of list write[] into file
p += 1
p = 0
lrlLabel.set(write[0])
urlLabel.set(write[1])
aaLabel.set(write[2])
apwLabel.set(write[3])
msrLabel.set(write[4])
atLabel.set(write[5])
reacLabel.set(write[6])
rfLabel.set(write[7])
recoLabel.set(write[8])
asLabel.set(write[9])
arpLabel.set(write[10])
pvarpLabel.set(write[11])
rsLabel.set(write[12])
paraWindow.destroy()
def changePara():
write = ['N/A'] * 7
d = 0
write[0] = LRL_roll.get()
write[1] = URL_roll.get()
if int(write[0]) > int(write[1]):
tkinter.messagebox.showerror(
'Error',
'Lower Rate Limit cannot be bigger than Upper Rate Limit')
else:
write[2] = VA_roll.get()
vvi_va_p = VA_roll.get()
if vvi_va_p == 'OFF':
vvi_va_p = 0
else:
vvi_va_p = int(100 * float(vvi_va_p))
write[3] = VPW_roll.get()
write[4] = VS_roll.get()
write[5] = VRP_roll.get()
write[6] = RS_roll.get()
if checkConnect() == 6:
connectLable.set("No Pacemaker Connected")
label = tk.Label(root_VVI,
textvariable=connectLable,
font=("Times New Roman", 14),
fg="red").place(x=10, y=40)
label = tk.Label(paraWindow,
textvariable=connectLable,
font=("Times New Roman", 14),
fg="red").place(x=10, y=40)
tkinter.messagebox.showerror(
'Error', 'Failed to connect to the Pacemaker')
else:
connectLable.set("Pacemaker is Connected")
label = tk.Label(root_VVI,
textvariable=connectLable,
font=("Times New Roman", 14),
fg="green").place(x=10, y=40)
label = tk.Label(paraWindow,
textvariable=connectLable,
font=("Times New Roman", 14),
fg="green").place(x=10, y=40)
writePara(mode=4,
Lower_Rate=int(LRL_roll.get()),
VENT_Amplitude=int(vvi_va_p),
VENT_Width=int(VPW_roll.get()),
VENT_Refractory=int(VRP_roll.get()))
with open("parameterVVI.txt", "w") as parameterFile:
while (d < 7):
parameterFile.write(
write[d] +
"\n") #Write every index of list write[] into file
d += 1
d = 0
lrlLabel.set(write[0])
urlLabel.set(write[1])
vaLabel.set(write[2])
vpwLabel.set(write[3])
vsLabel.set(write[4])
vrpLabel.set(write[5])
rsLabel.set(write[6])
paraWindow.destroy()
