def write_fuselage_conformal_fuel_tank(fuse_id,fuel_tank,fuel_tank_set_ind):
"""This writes a conformal fuel tank in a fuselage.
Assumptions:
Fuselage is aligned with the x axis
Source:
N/A
Inputs:
fuse_id <str>
fuel_tank.
inward_offset [m]
start_length_percent [-] .1 is 10%
end_length_percent [-]
fuel_type.density [kg/m^3]
fuel_tank_set_ind <int>
Outputs:
Operates on the active OpenVSP model, no direct output
Properties Used:
N/A
"""
#stdout = vsp.cvar.cstdout
#errorMgr = vsp.ErrorMgrSingleton_getInstance()
#errorMgr.PopErrorAndPrint(stdout)
# Unpack
try:
offset = fuel_tank.inward_offset
len_trim_max = fuel_tank.end_length_percent
len_trim_min = fuel_tank.start_length_percent
density = fuel_tank.fuel_type.density
except:
print('Fuel tank does not contain parameters needed for OpenVSP geometry. Tag: '+fuel_tank.tag)
return
tank_id = vsp.AddGeom('CONFORMAL',fuse_id)
vsp.SetGeomName(tank_id, fuel_tank.tag)
# Search for proper x position
# Get min x
probe_id = vsp.AddProbe(fuse_id,0,0,0,fuel_tank.tag+'_probe')
vsp.Update()
x_id = vsp.FindParm(probe_id,'X','Measure')
x_pos = vsp.GetParmVal(x_id)
fuse_x_min = x_pos
vsp.DelProbe(probe_id)
# Get min x
probe_id = vsp.AddProbe(fuse_id,0,1,0,fuel_tank.tag+'_probe')
vsp.Update()
x_id = vsp.FindParm(probe_id,'X','Measure')
x_pos = vsp.GetParmVal(x_id)
fuse_x_max = x_pos
vsp.DelProbe(probe_id)
# Search for u values
x_target_start = (fuse_x_max-fuse_x_min)*fuel_tank.start_length_percent
x_target_end = (fuse_x_max-fuse_x_min)*fuel_tank.end_length_percent
u_start = find_fuse_u_coordinate(x_target_start, fuse_id, fuel_tank.tag)
u_end = find_fuse_u_coordinate(x_target_end, fuse_id, fuel_tank.tag)
# Offset
vsp.SetParmVal(tank_id,'Offset','Design',offset)
# Fuel tank length bounds
vsp.SetParmVal(tank_id,'UTrimFlag','Design',1.)
vsp.SetParmVal(tank_id,'UTrimMax','Design',u_end)
vsp.SetParmVal(tank_id,'UTrimMin','Design',u_start)
# Set density
vsp.SetParmVal(tank_id,'Density','Mass_Props',density)
# Add to the full fuel tank set
vsp.SetSetFlag(tank_id, fuel_tank_set_ind, True)
return
def __init__(self,
vspFile,
comm=MPI.COMM_WORLD,
scale=1.0,
comps=[],
intersectedComps=None,
debug=False):
self.points = OrderedDict()
self.pointSets = OrderedDict()
self.updated = {}
self.vspScale = scale
self.comm = comm
self.vspFile = vspFile
self.debug = debug
self.jac = None
# Load in the VSP model
vsp.ClearVSPModel()
vsp.ReadVSPFile(vspFile)
# Setup the export group set (0) with just the sets we want.
self.exportSet = 9
# List of all componets returned from VSP. Note that this
# order is important...it is the order the comps will be
# written out in plot3d format.
allComps = vsp.FindGeoms()
# If we were not given comps, use all of them
if comps == []:
for c in allComps:
comps.append(vsp.GetContainerName(c))
# First set the export flag for exportSet to False for everyone
for comp in allComps:
vsp.SetSetFlag(comp, self.exportSet, False)
self.exportComps = []
for comp in allComps:
# Check if this one is in our list:
compName = vsp.GetContainerName(comp)
if compName in comps:
vsp.SetSetFlag(comp, self.exportSet, True)
self.exportComps.append(compName)
# Create a directory in which we will put the temporary files
# we need. We *should* use something like tmepfile.mkdtemp()
# but that behaves badly on pleiades.
tmpDir = None
if self.comm.rank == 0:
tmpDir = './tmpDir_%d_%s' % (MPI.COMM_WORLD.rank, time.time())
print('Temp dir is: %s' % tmpDir)
if not os.path.exists(tmpDir):
os.makedirs(tmpDir)
self.tmpDir = self.comm.bcast(tmpDir)
# Initial list of DVs
self.DVs = OrderedDict()
# Run the update. This will also set the conn on the first pass
self.conn = None
self.pts0 = None
self.cumSizes = None
self.sizes = None
if self.comm.rank == 0:
self.pts0, self.conn, self.cumSizes, self.sizes = self._getUpdatedSurface(
)
self.pts0 = self.comm.bcast(self.pts0)
self.conn = self.comm.bcast(self.conn)
self.cumSizes = self.comm.bcast(self.cumSizes)
self.sizes = self.comm.bcast(self.sizes)
self.pts = self.pts0.copy()
# Finally process theintersection information. We had to wait
# until all processors have the surface information.
self.intersectComps = []
if intersectedComps is None:
intersectedComps = []
for i in range(len(intersectedComps)):
c = intersectedComps[i]
# Get the index of each of the two comps:
compIndexA = self.exportComps.index(c[0])
compIndexB = self.exportComps.index(c[1])
direction = c[2]
dStar = c[3]
extraComps = []
if len(c) == 5:
for j in range(len(c[4])):
extraComps.append(self.exportComps.index(c[4][j]))
self.intersectComps.append(
CompIntersection(compIndexA, compIndexB, extraComps, direction,
dStar, self.pts, self.cumSizes, self.sizes,
self.tmpDir))
def write_wing_conformal_fuel_tank(wing, wing_id,fuel_tank,fuel_tank_set_ind):
"""This writes a conformal fuel tank in a wing.
Assumptions:
None
Source:
N/A
Inputs:
wing.Segments.*.percent_span_location [-]
wing.spans.projected [m]
wind_id <str>
fuel_tank.
inward_offset [m]
start_chord_percent [-] .1 is 10%
end_chord_percent [-]
start_span_percent [-]
end_span_percent [-]
fuel_type.density [kg/m^3]
fuel_tank_set_ind <int>
Outputs:
Operates on the active OpenVSP model, no direct output
Properties Used:
N/A
"""
# Unpack
try:
offset = fuel_tank.inward_offset
chord_trim_max = 1.-fuel_tank.start_chord_percent
chord_trim_min = 1.-fuel_tank.end_chord_percent
span_trim_max = fuel_tank.end_span_percent
span_trim_min = fuel_tank.start_span_percent
density = fuel_tank.fuel_type.density
except:
print('Fuel tank does not contain parameters needed for OpenVSP geometry. Tag: '+fuel_tank.tag)
return
tank_id = vsp.AddGeom('CONFORMAL',wing_id)
vsp.SetGeomName(tank_id, fuel_tank.tag)
n_segments = len(wing.Segments.keys())
if n_segments > 0.:
seg_span_percents = np.array([v['percent_span_location'] for (k,v)\
in wing.Segments.iteritems()])
vsp_segment_breaks = np.linspace(0.,1.,n_segments)
else:
seg_span_percents = np.array([0.,1.])
span = wing.spans.projected
# Offset
vsp.SetParmVal(tank_id,'Offset','Design',offset)
for key, fuselage in vehicle.fuselages.items():
width = fuselage.width
length = fuselage.lengths.total
hmax = fuselage.heights.maximum
height1 = fuselage.heights.at_quarter_length
height2 = fuselage.heights.at_wing_root_quarter_chord
height3 = fuselage.heights.at_three_quarters_length
effdia = fuselage.effective_diameter
n_fine = fuselage.fineness.nose
t_fine = fuselage.fineness.tail
w_ac = wing.aerodynamic_center
w_origin = vehicle.wings.main_wing.origin
w_c_4 = vehicle.wings.main_wing.chords.root/4.
# Figure out the location x location of each section, 3 sections, end of nose, wing origin, and start of tail
x1 = 0.25
x2 = (w_origin[0]+w_c_4)/length
x3 = 0.75
fuse_id = vsp.AddGeom("FUSELAGE")
vsp.SetGeomName(fuse_id, fuselage.tag)
area_tags[fuselage.tag] = ['fuselages',fuselage.tag]
# Set the origins:
x = fuselage.origin[0][0]
y = fuselage.origin[0][1]
z = fuselage.origin[0][2]
vsp.SetParmVal(fuse_id,'X_Location','XForm',x)
vsp.SetParmVal(fuse_id,'Y_Location','XForm',y)
vsp.SetParmVal(fuse_id,'Z_Location','XForm',z)
vsp.SetParmVal(fuse_id,'Abs_Or_Relitive_flag','XForm',vsp.ABS) # misspelling from OpenVSP
vsp.SetParmVal(fuse_id,'Origin','XForm',0.0)
# Fuel tank chord bounds
vsp.SetParmVal(tank_id,'ChordTrimFlag','Design',1.)
vsp.SetParmVal(tank_id,'ChordTrimMax','Design',chord_trim_max)
vsp.SetParmVal(tank_id,'ChordTrimMin','Design',chord_trim_min)
# Fuel tank span bounds
if n_segments>0:
span_trim_max = get_vsp_trim_from_SUAVE_trim(seg_span_percents,
vsp_segment_breaks,
span_trim_max)
span_trim_min = get_vsp_trim_from_SUAVE_trim(seg_span_percents,
vsp_segment_breaks,
span_trim_min)
else:
pass # no change to span_trim
vsp.SetParmVal(tank_id,'UTrimFlag','Design',1.)
vsp.SetParmVal(tank_id,'UTrimMax','Design',span_trim_max)
vsp.SetParmVal(tank_id,'UTrimMin','Design',span_trim_min)
# Set density
vsp.SetParmVal(tank_id,'Density','Mass_Props',density)
# Add to the full fuel tank set
vsp.SetSetFlag(tank_id, fuel_tank_set_ind, True)
return
def write_vsp_fuselage(fuselage,area_tags, main_wing, fuel_tank_set_ind, OML_set_ind):
"""This writes a fuselage into OpenVSP format.
Assumptions:
None
Source:
N/A
Inputs:
fuselage
width [m]
lengths.total [m]
heights.
maximum [m]
at_quarter_length [m]
at_wing_root_quarter_chord [m]
at_three_quarters_length [m]
effective_diameter [m]
fineness.nose [-] ratio of nose section length to fuselage width
fineness.tail [-] ratio of tail section length to fuselage width
tag <string>
OpenVSP_values. (optional)
nose.top.angle [degrees]
nose.top.strength [-] this determines how much the specified angle influences that shape
nose.side.angle [degrees]
nose.side.strength [-]
nose.TB_Sym <boolean> determines if top angle is mirrored on bottom
nose.z_pos [-] z position of the nose as a percentage of fuselage length (.1 is 10%)
tail.top.angle [degrees]
tail.top.strength [-]
tail.z_pos (optional, 0.02 default) [-] z position of the tail as a percentage of fuselage length (.1 is 10%)
Segments. (optional)
width [m]
height [m]
percent_x_location [-] .1 is 10% length
percent_z_location [-] .1 is 10% length
area_tags <dict> used to keep track of all tags needed in wetted area computation
main_wing.origin [m]
main_wing.chords.root [m]
fuel_tank_set_index <int> OpenVSP object set containing the fuel tanks
Outputs:
Operates on the active OpenVSP model, no direct output
Properties Used:
N/A
"""
num_segs = len(fuselage.Segments)
length = fuselage.lengths.total
fuse_x = fuselage.origin[0][0]
fuse_y = fuselage.origin[0][1]
fuse_z = fuselage.origin[0][2]
fuse_x_rotation = fuselage.x_rotation
fuse_y_rotation = fuselage.y_rotation
fuse_z_rotation = fuselage.z_rotation
if num_segs==0: # SUAVE default fuselage shaping
width = fuselage.width
hmax = fuselage.heights.maximum
height1 = fuselage.heights.at_quarter_length
height2 = fuselage.heights.at_wing_root_quarter_chord
height3 = fuselage.heights.at_three_quarters_length
effdia = fuselage.effective_diameter
n_fine = fuselage.fineness.nose
t_fine = fuselage.fineness.tail
try:
if main_wing != None:
w_origin = main_wing.origin
w_c_4 = main_wing.chords.root/4.
else:
w_origin = 0.5*length
w_c_4 = 0.5*length
except AttributeError:
raise AttributeError('Main wing not detected. Fuselage must have specified sections in this configuration.')
# Figure out the location x location of each section, 3 sections, end of nose, wing origin, and start of tail
x1 = n_fine*width/length
x2 = (w_origin[0][0]+w_c_4)/length
x3 = 1-t_fine*width/length
end_ind = 4
else: # Fuselage shaping based on sections
widths = []
heights = []
x_poses = []
z_poses = []
segs = fuselage.Segments
for seg in segs:
widths.append(seg.width)
heights.append(seg.height)
x_poses.append(seg.percent_x_location)
z_poses.append(seg.percent_z_location)
end_ind = num_segs-1
fuse_id = vsp.AddGeom("FUSELAGE")
vsp.SetGeomName(fuse_id, fuselage.tag)
area_tags[fuselage.tag] = ['fuselages',fuselage.tag]
tail_z_pos = 0.02 # default value
# set fuselage relative location and rotation
vsp.SetParmVal( fuse_id,'X_Rel_Rotation','XForm',fuse_x_rotation)
vsp.SetParmVal( fuse_id,'Y_Rel_Rotation','XForm',fuse_y_rotation)
vsp.SetParmVal( fuse_id,'Z_Rel_Rotation','XForm',fuse_z_rotation)
vsp.SetParmVal( fuse_id,'X_Rel_Location','XForm',fuse_x)
vsp.SetParmVal( fuse_id,'Y_Rel_Location','XForm',fuse_y)
vsp.SetParmVal( fuse_id,'Z_Rel_Location','XForm',fuse_z)
if 'OpenVSP_values' in fuselage:
vals = fuselage.OpenVSP_values
# for wave drag testing
fuselage.OpenVSP_ID = fuse_id
# Nose
vsp.SetParmVal(fuse_id,"TopLAngle","XSec_0",vals.nose.top.angle)
vsp.SetParmVal(fuse_id,"TopLStrength","XSec_0",vals.nose.top.strength)
vsp.SetParmVal(fuse_id,"RightLAngle","XSec_0",vals.nose.side.angle)
vsp.SetParmVal(fuse_id,"RightLStrength","XSec_0",vals.nose.side.strength)
vsp.SetParmVal(fuse_id,"TBSym","XSec_0",vals.nose.TB_Sym)
vsp.SetParmVal(fuse_id,"ZLocPercent","XSec_0",vals.nose.z_pos)
if not vals.nose.TB_Sym:
vsp.SetParmVal(fuse_id,"BottomLAngle","XSec_0",vals.nose.bottom.angle)
vsp.SetParmVal(fuse_id,"BottomLStrength","XSec_0",vals.nose.bottom.strength)
# Tail
# Below can be enabled if AllSym (below) is removed
#vsp.SetParmVal(fuse_id,"RightLAngle","XSec_4",vals.tail.side.angle)
#vsp.SetParmVal(fuse_id,"RightLStrength","XSec_4",vals.tail.side.strength)
#vsp.SetParmVal(fuse_id,"TBSym","XSec_4",vals.tail.TB_Sym)
#vsp.SetParmVal(fuse_id,"BottomLAngle","XSec_4",vals.tail.bottom.angle)
#vsp.SetParmVal(fuse_id,"BottomLStrength","XSec_4",vals.tail.bottom.strength)
if 'z_pos' in vals.tail:
tail_z_pos = vals.tail.z_pos
else:
pass # use above default
if num_segs == 0:
vsp.SetParmVal(fuse_id,"Length","Design",length)
vsp.SetParmVal(fuse_id,"Diameter","Design",width)
vsp.SetParmVal(fuse_id,"XLocPercent","XSec_1",x1)
vsp.SetParmVal(fuse_id,"XLocPercent","XSec_2",x2)
vsp.SetParmVal(fuse_id,"XLocPercent","XSec_3",x3)
vsp.SetParmVal(fuse_id,"ZLocPercent","XSec_4",tail_z_pos)
vsp.SetParmVal(fuse_id, "Ellipse_Width", "XSecCurve_1", width)
vsp.SetParmVal(fuse_id, "Ellipse_Width", "XSecCurve_2", width)
vsp.SetParmVal(fuse_id, "Ellipse_Width", "XSecCurve_3", width)
vsp.SetParmVal(fuse_id, "Ellipse_Height", "XSecCurve_1", height1);
vsp.SetParmVal(fuse_id, "Ellipse_Height", "XSecCurve_2", height2);
vsp.SetParmVal(fuse_id, "Ellipse_Height", "XSecCurve_3", height3);
else:
# OpenVSP vals do not exist:
vals = Data()
vals.nose = Data()
vals.tail = Data()
vals.tail.top = Data()
vals.nose.z_pos = 0.0
vals.tail.top.angle = 0.0
vals.tail.top.strength = 0.0
if len(np.unique(x_poses)) != len(x_poses):
raise ValueError('Duplicate fuselage section positions detected.')
vsp.SetParmVal(fuse_id,"Length","Design",length)
if num_segs != 5: # reduce to only nose and tail
vsp.CutXSec(fuse_id,1) # remove extra default section
vsp.CutXSec(fuse_id,1) # remove extra default section
vsp.CutXSec(fuse_id,1) # remove extra default section
for i in range(num_segs-2): # add back the required number of sections
vsp.InsertXSec(fuse_id, 0, vsp.XS_ELLIPSE)
vsp.Update()
for i in range(num_segs-2):
# Bunch sections to allow proper length settings in the next step
# This is necessary because OpenVSP will not move a section past an adjacent section
vsp.SetParmVal(fuse_id, "XLocPercent", "XSec_"+str(i+1),1e-6*(i+1))
vsp.Update()
if x_poses[1] < (num_segs-2)*1e-6:
print('Warning: Second fuselage section is too close to the nose. OpenVSP model may not be accurate.')
for i in reversed(range(num_segs-2)):
# order is reversed because sections are initially bunched in the front and cannot be extended passed the next
vsp.SetParmVal(fuse_id, "XLocPercent", "XSec_"+str(i+1),x_poses[i+1])
vsp.SetParmVal(fuse_id, "ZLocPercent", "XSec_"+str(i+1),z_poses[i+1])
vsp.SetParmVal(fuse_id, "Ellipse_Width", "XSecCurve_"+str(i+1), widths[i+1])
vsp.SetParmVal(fuse_id, "Ellipse_Height", "XSecCurve_"+str(i+1), heights[i+1])
vsp.Update()
set_section_angles(i, vals.nose.z_pos, tail_z_pos, x_poses, z_poses, heights, widths,length,end_ind,fuse_id)
vsp.SetParmVal(fuse_id, "XLocPercent", "XSec_"+str(0),x_poses[0])
vsp.SetParmVal(fuse_id, "ZLocPercent", "XSec_"+str(0),z_poses[0])
vsp.SetParmVal(fuse_id, "XLocPercent", "XSec_"+str(end_ind),x_poses[-1])
vsp.SetParmVal(fuse_id, "ZLocPercent", "XSec_"+str(end_ind),z_poses[-1])
# Tail
if heights[-1] > 0.:
stdout = vsp.cvar.cstdout
errorMgr = vsp.ErrorMgrSingleton_getInstance()
errorMgr.PopErrorAndPrint(stdout)
pos = len(heights)-1
vsp.InsertXSec(fuse_id, pos-1, vsp.XS_ELLIPSE)
vsp.Update()
vsp.SetParmVal(fuse_id, "Ellipse_Width", "XSecCurve_"+str(pos), widths[-1])
vsp.SetParmVal(fuse_id, "Ellipse_Height", "XSecCurve_"+str(pos), heights[-1])
vsp.SetParmVal(fuse_id, "XLocPercent", "XSec_"+str(pos),x_poses[-1])
vsp.SetParmVal(fuse_id, "ZLocPercent", "XSec_"+str(pos),z_poses[-1])
xsecsurf = vsp.GetXSecSurf(fuse_id,0)
vsp.ChangeXSecShape(xsecsurf,pos+1,vsp.XS_POINT)
vsp.Update()
vsp.SetParmVal(fuse_id, "XLocPercent", "XSec_"+str(pos+1),x_poses[-1])
vsp.SetParmVal(fuse_id, "ZLocPercent", "XSec_"+str(pos+1),z_poses[-1])
# update strengths to make end flat
vsp.SetParmVal(fuse_id,"TopRStrength","XSec_"+str(pos), 0.)
vsp.SetParmVal(fuse_id,"RightRStrength","XSec_"+str(pos), 0.)
vsp.SetParmVal(fuse_id,"BottomRStrength","XSec_"+str(pos), 0.)
vsp.SetParmVal(fuse_id,"TopLStrength","XSec_"+str(pos+1), 0.)
vsp.SetParmVal(fuse_id,"RightLStrength","XSec_"+str(pos+1), 0.)
else:
vsp.SetParmVal(fuse_id,"TopLAngle","XSec_"+str(end_ind),vals.tail.top.angle)
vsp.SetParmVal(fuse_id,"TopLStrength","XSec_"+str(end_ind),vals.tail.top.strength)
vsp.SetParmVal(fuse_id,"AllSym","XSec_"+str(end_ind),1)
vsp.Update()
if 'z_pos' in vals.tail:
tail_z_pos = vals.tail.z_pos
else:
pass # use above default
if 'Fuel_Tanks' in fuselage:
for tank in fuselage.Fuel_Tanks:
write_fuselage_conformal_fuel_tank(fuse_id, tank, fuel_tank_set_ind)
vsp.SetSetFlag(fuse_id, OML_set_ind, True)
return area_tags
def write_vsp_turbofan(turbofan, OML_set_ind):
"""This converts turbofans into OpenVSP format.
Assumptions:
None
Source:
N/A
Inputs:
turbofan.
number_of_engines [-]
engine_length [m]
nacelle_diameter [m]
origin [m] in all three dimension, should have as many origins as engines
OpenVSP_flow_through <boolean> if True create a flow through nacelle, if False create a cylinder
Outputs:
Operates on the active OpenVSP model, no direct output
Properties Used:
N/A
"""
n_engines = turbofan.number_of_engines
length = turbofan.engine_length
width = turbofan.nacelle_diameter
origins = turbofan.origin
inlet_width = turbofan.inlet_diameter
tf_tag = turbofan.tag
# True will create a flow-through subsonic nacelle (which may have dimensional errors)
# False will create a cylindrical stack (essentially a cylinder)
ft_flag = turbofan.OpenVSP_flow_through
import operator # import here since engines are not always needed
# sort engines per left to right convention
origins_sorted = sorted(origins, key=operator.itemgetter(1))
for ii in range(0,int(n_engines)):
origin = origins_sorted[ii]
x = origin[0]
y = origin[1]
z = origin[2]
if ft_flag == True:
nac_id = vsp.AddGeom( "BODYOFREVOLUTION")
vsp.SetGeomName(nac_id, tf_tag+'_'+str(ii+1))
# Origin
vsp.SetParmVal(nac_id,'X_Location','XForm',x)
vsp.SetParmVal(nac_id,'Y_Location','XForm',y)
vsp.SetParmVal(nac_id,'Z_Location','XForm',z)
vsp.SetParmVal(nac_id,'Abs_Or_Relitive_flag','XForm',vsp.ABS) # misspelling from OpenVSP
# Length and overall diameter
vsp.SetParmVal(nac_id,"Diameter","Design",inlet_width)
vsp.ChangeBORXSecShape(nac_id ,vsp.XS_SUPER_ELLIPSE)
vsp.Update()
vsp.SetParmVal(nac_id, "Super_Height", "XSecCurve", (width-inlet_width)/2)
vsp.SetParmVal(nac_id, "Super_Width", "XSecCurve", length)
vsp.SetParmVal(nac_id, "Super_MaxWidthLoc", "XSecCurve", -1.)
vsp.SetParmVal(nac_id, "Super_M", "XSecCurve", 2.)
vsp.SetParmVal(nac_id, "Super_N", "XSecCurve", 1.)
else:
nac_id = vsp.AddGeom("STACK")
vsp.SetGeomName(nac_id, tf_tag+'_'+str(ii+1))
# Origin
vsp.SetParmVal(nac_id,'X_Location','XForm',x)
vsp.SetParmVal(nac_id,'Y_Location','XForm',y)
vsp.SetParmVal(nac_id,'Z_Location','XForm',z)
vsp.SetParmVal(nac_id,'Abs_Or_Relitive_flag','XForm',vsp.ABS) # misspelling from OpenVSP
vsp.SetParmVal(nac_id,'Origin','XForm',0.5)
vsp.CutXSec(nac_id,2) # remove extra default subsurface
xsecsurf = vsp.GetXSecSurf(nac_id,0)
vsp.ChangeXSecShape(xsecsurf,1,vsp.XS_CIRCLE)
vsp.ChangeXSecShape(xsecsurf,2,vsp.XS_CIRCLE)
vsp.Update()
vsp.SetParmVal(nac_id, "Circle_Diameter", "XSecCurve_1", width)
vsp.SetParmVal(nac_id, "Circle_Diameter", "XSecCurve_2", width)
vsp.SetParmVal(nac_id, "XDelta", "XSec_1", 0)
vsp.SetParmVal(nac_id, "XDelta", "XSec_2", length)
vsp.SetParmVal(nac_id, "XDelta", "XSec_3", 0)
vsp.SetSetFlag(nac_id, OML_set_ind, True)
vsp.Update()
def write_vsp_wing(wing, area_tags, fuel_tank_set_ind, OML_set_ind):
"""This write a given wing into OpenVSP format
Assumptions:
If wing segments are defined, they must cover the full span.
(may work in some other cases, but functionality will not be maintained)
Source:
N/A
Inputs:
wing.
origin [m] in all three dimensions
spans.projected [m]
chords.root [m]
chords.tip [m]
sweeps.quarter_chord [radians]
twists.root [radians]
twists.tip [radians]
thickness_to_chord [-]
dihedral [radians]
tag <string>
Segments.*. (optional)
twist [radians]
percent_span_location [-] .1 is 10%
root_chord_percent [-] .1 is 10%
dihedral_outboard [radians]
sweeps.quarter_chord [radians]
thickness_to_chord [-]
area_tags <dict> used to keep track of all tags needed in wetted area computation
fuel_tank_set_index <int> OpenVSP object set containing the fuel tanks
Outputs:
area_tags <dict> used to keep track of all tags needed in wetted area computation
wing_id <str> OpenVSP ID for given wing
Properties Used:
N/A
"""
wing_x = wing.origin[0][0]
wing_y = wing.origin[0][1]
wing_z = wing.origin[0][2]
if wing.symmetric == True:
span = wing.spans.projected/2. # span of one side
else:
span = wing.spans.projected
root_chord = wing.chords.root
tip_chord = wing.chords.tip
sweep = wing.sweeps.quarter_chord / Units.deg
sweep_loc = 0.25
root_twist = wing.twists.root / Units.deg
tip_twist = wing.twists.tip / Units.deg
root_tc = wing.thickness_to_chord
tip_tc = wing.thickness_to_chord
dihedral = wing.dihedral / Units.deg
# Check to see if segments are defined. Get count
if len(wing.Segments.keys())>0:
n_segments = len(wing.Segments.keys())
else:
n_segments = 0
# Create the wing
wing_id = vsp.AddGeom( "WING" )
vsp.SetGeomName(wing_id, wing.tag)
area_tags[wing.tag] = ['wings',wing.tag]
# Make names for each section and insert them into the wing if necessary
x_secs = []
x_sec_curves = []
# n_segments + 2 will create an extra segment if the root segment is
# included in the list of segments. This is not used and the tag is
# removed when the segments are checked for this case.
for i_segs in range(0,n_segments+2):
x_secs.append('XSec_' + str(i_segs))
x_sec_curves.append('XSecCurve_' + str(i_segs))
# Apply the basic characteristics of the wing to root and tip
if wing.symmetric == False:
vsp.SetParmVal( wing_id,'Sym_Planar_Flag','Sym',0)
if wing.vertical == True:
vsp.SetParmVal( wing_id,'X_Rel_Rotation','XForm',90)
dihedral = -dihedral # check for vertical tail, direction reverses from SUAVE/AVL
vsp.SetParmVal( wing_id,'X_Rel_Location','XForm',wing_x)
vsp.SetParmVal( wing_id,'Y_Rel_Location','XForm',wing_y)
vsp.SetParmVal( wing_id,'Z_Rel_Location','XForm',wing_z)
# This ensures that the other VSP parameters are driven properly
vsp.SetDriverGroup( wing_id, 1, vsp.SPAN_WSECT_DRIVER, vsp.ROOTC_WSECT_DRIVER, vsp.TIPC_WSECT_DRIVER )
# Root chord
vsp.SetParmVal( wing_id,'Root_Chord',x_secs[1],root_chord)
# Sweep of the first section
vsp.SetParmVal( wing_id,'Sweep',x_secs[1],sweep)
vsp.SetParmVal( wing_id,'Sweep_Location',x_secs[1],sweep_loc)
# Twists
if n_segments != 0:
if np.isclose(wing.Segments[0].percent_span_location,0.):
vsp.SetParmVal( wing_id,'Twist',x_secs[0],wing.Segments[0].twist / Units.deg) # root
else:
vsp.SetParmVal( wing_id,'Twist',x_secs[0],root_twist) # root
# The tips should write themselves
else:
vsp.SetParmVal( wing_id,'Twist',x_secs[0],root_twist) # root
vsp.SetParmVal( wing_id,'Twist',x_secs[1],tip_twist) # tip
# Figure out if there is an airfoil provided
# Airfoils should be in Lednicer format
# i.e. :
#
#EXAMPLE AIRFOIL
# 3. 3.
#
# 0.0 0.0
# 0.5 0.1
# 1.0 0.0
#
# 0.0 0.0
# 0.5 -0.1
# 1.0 0.0
# Note this will fail silently if airfoil is not in correct format
# check geometry output
airfoil_vsp_types = []
if n_segments > 0:
for i in range(n_segments):
if 'airfoil_type' in wing.Segments[i].keys():
if wing.Segments[i].airfoil_type == 'biconvex':
airfoil_vsp_types.append(vsp.XS_BICONVEX)
else:
airfoil_vsp_types.append(vsp.XS_FILE_AIRFOIL)
else:
airfoil_vsp_types.append(vsp.XS_FILE_AIRFOIL)
elif 'airfoil_type' in wing.keys():
if wing.airfoil_type == 'biconvex':
airfoil_vsp_types.append(vsp.XS_BICONVEX)
else:
airfoil_vsp_types.append(vsp.XS_FILE_AIRFOIL)
else:
airfoil_vsp_types = [vsp.XS_FILE_AIRFOIL]
if n_segments==0:
if len(wing.Airfoil) != 0 or 'airfoil_type' in wing.keys():
xsecsurf = vsp.GetXSecSurf(wing_id,0)
vsp.ChangeXSecShape(xsecsurf,0,airfoil_vsp_types[0])
vsp.ChangeXSecShape(xsecsurf,1,airfoil_vsp_types[0])
if len(wing.Airfoil) != 0:
xsec1 = vsp.GetXSec(xsecsurf,0)
xsec2 = vsp.GetXSec(xsecsurf,1)
vsp.ReadFileAirfoil(xsec1,wing.Airfoil['airfoil'].coordinate_file)
vsp.ReadFileAirfoil(xsec2,wing.Airfoil['airfoil'].coordinate_file)
vsp.Update()
else:
if len(wing.Segments[0].Airfoil) != 0 or 'airfoil_type' in wing.Segments[0].keys():
xsecsurf = vsp.GetXSecSurf(wing_id,0)
vsp.ChangeXSecShape(xsecsurf,0,airfoil_vsp_types[0])
vsp.ChangeXSecShape(xsecsurf,1,airfoil_vsp_types[0])
if len(wing.Segments[0].Airfoil) != 0:
xsec1 = vsp.GetXSec(xsecsurf,0)
xsec2 = vsp.GetXSec(xsecsurf,1)
vsp.ReadFileAirfoil(xsec1,wing.Segments[0].Airfoil['airfoil'].coordinate_file)
vsp.ReadFileAirfoil(xsec2,wing.Segments[0].Airfoil['airfoil'].coordinate_file)
vsp.Update()
# Thickness to chords
vsp.SetParmVal( wing_id,'ThickChord','XSecCurve_0',root_tc)
vsp.SetParmVal( wing_id,'ThickChord','XSecCurve_1',tip_tc)
# Dihedral
vsp.SetParmVal( wing_id,'Dihedral',x_secs[1],dihedral)
# Span and tip of the section
if n_segments>1:
local_span = span*wing.Segments[0].percent_span_location
sec_tip_chord = root_chord*wing.Segments[0].root_chord_percent
vsp.SetParmVal( wing_id,'Span',x_secs[1],local_span)
vsp.SetParmVal( wing_id,'Tip_Chord',x_secs[1],sec_tip_chord)
else:
vsp.SetParmVal( wing_id,'Span',x_secs[1],span/np.cos(dihedral*Units.degrees))
vsp.Update()
if n_segments>0:
if wing.Segments[0].percent_span_location==0.:
x_secs[-1] = [] # remove extra section tag (for clarity)
segment_0_is_root_flag = True
adjust = 0 # used for indexing
else:
segment_0_is_root_flag = False
adjust = 1
else:
adjust = 1
# Loop for the number of segments left over
for i_segs in range(1,n_segments+1):
if (wing.Segments[i_segs-1] == wing.Segments[-1]) and (wing.Segments[-1].percent_span_location == 1.):
break
# Unpack
dihedral_i = wing.Segments[i_segs-1].dihedral_outboard / Units.deg
chord_i = root_chord*wing.Segments[i_segs-1].root_chord_percent
try:
twist_i = wing.Segments[i_segs].twist / Units.deg
no_twist_flag = False
except:
no_twist_flag = True
sweep_i = wing.Segments[i_segs-1].sweeps.quarter_chord / Units.deg
tc_i = wing.Segments[i_segs-1].thickness_to_chord
# Calculate the local span
if i_segs == n_segments:
span_i = span*(1 - wing.Segments[i_segs-1].percent_span_location)/np.cos(dihedral_i*Units.deg)
else:
span_i = span*(wing.Segments[i_segs].percent_span_location-wing.Segments[i_segs-1].percent_span_location)/np.cos(dihedral_i*Units.deg)
# Insert the new wing section with specified airfoil if available
if len(wing.Segments[i_segs-1].Airfoil) != 0 or 'airfoil_type' in wing.Segments[i_segs-1].keys():
vsp.InsertXSec(wing_id,i_segs-1+adjust,airfoil_vsp_types[i_segs-1])
if len(wing.Segments[i_segs-1].Airfoil) != 0:
xsecsurf = vsp.GetXSecSurf(wing_id,0)
xsec = vsp.GetXSec(xsecsurf,i_segs+adjust)
vsp.ReadFileAirfoil(xsec, wing.Segments[i_segs-1].Airfoil['airfoil'].coordinate_file)
else:
vsp.InsertXSec(wing_id,i_segs-1+adjust,vsp.XS_FOUR_SERIES)
# Set the parms
vsp.SetParmVal( wing_id,'Span',x_secs[i_segs+adjust],span_i)
vsp.SetParmVal( wing_id,'Dihedral',x_secs[i_segs+adjust],dihedral_i)
vsp.SetParmVal( wing_id,'Sweep',x_secs[i_segs+adjust],sweep_i)
vsp.SetParmVal( wing_id,'Sweep_Location',x_secs[i_segs+adjust],sweep_loc)
vsp.SetParmVal( wing_id,'Root_Chord',x_secs[i_segs+adjust],chord_i)
if not no_twist_flag:
vsp.SetParmVal( wing_id,'Twist',x_secs[i_segs+adjust],twist_i)
vsp.SetParmVal( wing_id,'ThickChord',x_sec_curves[i_segs+adjust],tc_i)
if adjust and (i_segs == 1):
vsp.Update()
vsp.SetParmVal( wing_id,'Twist',x_secs[1],wing.Segments[i_segs-1].twist / Units.deg)
vsp.Update()
if (n_segments != 0) and (wing.Segments[-1].percent_span_location == 1.):
tip_chord = root_chord*wing.Segments[-1].root_chord_percent
vsp.SetParmVal( wing_id,'Tip_Chord',x_secs[n_segments-1+adjust],tip_chord)
vsp.SetParmVal( wing_id,'ThickChord',x_sec_curves[n_segments-1+adjust],wing.Segments[-1].thickness_to_chord)
# twist is set in the normal loop
else:
vsp.SetParmVal( wing_id,'Tip_Chord',x_secs[-1-(1-adjust)],tip_chord)
vsp.SetParmVal( wing_id,'Twist',x_secs[-1-(1-adjust)],tip_twist)
# a single trapezoidal wing is assumed to have constant thickness to chord
vsp.Update()
vsp.SetParmVal(wing_id,'CapUMaxOption','EndCap',2.)
vsp.SetParmVal(wing_id,'CapUMaxStrength','EndCap',1.)
vsp.Update() # to fix problems with chords not matching up
if 'Fuel_Tanks' in wing:
for tank in wing.Fuel_Tanks:
write_wing_conformal_fuel_tank(wing, wing_id, tank, fuel_tank_set_ind)
vsp.SetSetFlag(wing_id, OML_set_ind, True)
return area_tags, wing_id
def write_vsp_nacelle(nacelle, OML_set_ind):
"""This converts nacelles into OpenVSP format.
Assumptions:
1. If nacelle segments are defined, geometry written to OpenVSP is of type "StackGeom".
1.a This type of nacelle can be either set as flow through or not flow through.
1.b Segments are defined in a similar manner to fuselage segments. See geometric
documentation in SUAVE-Components-Nacelles-Nacelle
2. If nacelle segments are not defined, geometry written to OpenVSP is of type "BodyofRevolution".
2.a This type of nacelle can be either set as flow through or not flow through.
2.b BodyofRevolution can be either be a 4 digit airfoil (type string) or super ellipse (default)
Source:
N/A
Inputs:
nacelle.
origin [m] in all three dimension, should have as many origins as engines
length [m]
diameter [m]
flow_through <boolean> if True create a flow through nacelle, if False create a cylinder
segment(optional).
width [m]
height [m]
lenght [m]
percent_x_location [m]
percent_y_location [m]
percent_z_location [m]
Outputs:
Operates on the active OpenVSP model, no direct output
Properties Used:
N/A
"""
# default tesselation
radial_tesselation = 21
axial_tesselation = 25
# True will create a flow-through subsonic nacelle (which may have dimensional errors)
# False will create a cylindrical stack (essentially a cylinder)
ft_flag = nacelle.flow_through
length = nacelle.length
height = nacelle.diameter - nacelle.inlet_diameter
diameter = nacelle.diameter - height / 2
nac_tag = nacelle.tag
nac_x = nacelle.origin[0][0]
nac_y = nacelle.origin[0][1]
nac_z = nacelle.origin[0][2]
nac_x_rotation = nacelle.orientation_euler_angles[0] / Units.degrees
nac_y_rotation = nacelle.orientation_euler_angles[1] / Units.degrees
nac_z_rotation = nacelle.orientation_euler_angles[2] / Units.degrees
num_segs = len(nacelle.Segments)
if num_segs > 0:
if nacelle.Airfoil.naca_4_series_airfoil != None:
raise AssertionError(
'Nacelle segments defined. Airfoil section will not be used.')
nac_id = vsp.AddGeom("STACK")
vsp.SetGeomName(nac_id, nac_tag)
# set nacelle relative location and rotation
vsp.SetParmVal(nac_id, 'Abs_Or_Relitive_flag', 'XForm', vsp.ABS)
vsp.SetParmVal(nac_id, 'X_Rotation', 'XForm', nac_x_rotation)
vsp.SetParmVal(nac_id, 'Y_Rotation', 'XForm', nac_y_rotation)
vsp.SetParmVal(nac_id, 'Z_Rotation', 'XForm', nac_z_rotation)
vsp.SetParmVal(nac_id, 'X_Location', 'XForm', nac_x)
vsp.SetParmVal(nac_id, 'Y_Location', 'XForm', nac_y)
vsp.SetParmVal(nac_id, 'Z_Location', 'XForm', nac_z)
vsp.SetParmVal(nac_id, 'Tess_U', 'Shape', radial_tesselation)
vsp.SetParmVal(nac_id, 'Tess_W', 'Shape', axial_tesselation)
widths = []
heights = []
x_delta = []
x_poses = []
z_delta = []
segs = nacelle.Segments
for seg in range(num_segs):
widths.append(segs[seg].width)
heights.append(segs[seg].height)
x_poses.append(segs[seg].percent_x_location)
if seg == 0:
x_delta.append(0)
z_delta.append(0)
else:
x_delta.append(length * (segs[seg].percent_x_location -
segs[seg - 1].percent_x_location))
z_delta.append(length * (segs[seg].percent_z_location -
segs[seg - 1].percent_z_location))
vsp.CutXSec(nac_id, 4) # remove point section at end
vsp.CutXSec(nac_id, 0) # remove point section at beginning
vsp.CutXSec(nac_id, 1) # remove point section at beginning
for _ in range(num_segs -
2): # add back the required number of sections
vsp.InsertXSec(nac_id, 1, vsp.XS_ELLIPSE)
vsp.Update()
xsec_surf = vsp.GetXSecSurf(nac_id, 0)
for i3 in reversed(range(num_segs)):
xsec = vsp.GetXSec(xsec_surf, i3)
if i3 == 0:
pass
else:
vsp.SetParmVal(nac_id, "XDelta", "XSec_" + str(i3),
x_delta[i3])
vsp.SetParmVal(nac_id, "ZDelta", "XSec_" + str(i3),
z_delta[i3])
vsp.SetXSecWidthHeight(xsec, widths[i3], heights[i3])
vsp.SetXSecTanAngles(xsec, vsp.XSEC_BOTH_SIDES, 0, 0, 0, 0)
vsp.SetXSecTanSlews(xsec, vsp.XSEC_BOTH_SIDES, 0, 0, 0, 0)
vsp.SetXSecTanStrengths(xsec, vsp.XSEC_BOTH_SIDES, 0, 0, 0, 0)
vsp.Update()
if ft_flag:
pass
else:
# append front point
xsecsurf = vsp.GetXSecSurf(nac_id, 0)
vsp.ChangeXSecShape(xsecsurf, 0, vsp.XS_POINT)
vsp.Update()
xsecsurf = vsp.GetXSecSurf(nac_id, 0)
vsp.ChangeXSecShape(xsecsurf, num_segs - 1, vsp.XS_POINT)
vsp.Update()
else:
nac_id = vsp.AddGeom("BODYOFREVOLUTION")
vsp.SetGeomName(nac_id, nac_tag)
# Origin
vsp.SetParmVal(nac_id, 'Abs_Or_Relitive_flag', 'XForm', vsp.ABS)
vsp.SetParmVal(nac_id, 'X_Rotation', 'XForm', nac_x_rotation)
vsp.SetParmVal(nac_id, 'Y_Rotation', 'XForm', nac_y_rotation)
vsp.SetParmVal(nac_id, 'Z_Rotation', 'XForm', nac_z_rotation)
vsp.SetParmVal(nac_id, 'X_Location', 'XForm', nac_x)
vsp.SetParmVal(nac_id, 'Y_Location', 'XForm', nac_y)
vsp.SetParmVal(nac_id, 'Z_Location', 'XForm', nac_z)
vsp.SetParmVal(nac_id, 'Tess_U', 'Shape', radial_tesselation)
vsp.SetParmVal(nac_id, 'Tess_W', 'Shape', axial_tesselation)
# Length and overall diameter
vsp.SetParmVal(nac_id, "Diameter", "Design", diameter)
if ft_flag:
vsp.SetParmVal(nac_id, "Mode", "Design", 0.0)
else:
vsp.SetParmVal(nac_id, "Mode", "Design", 1.0)
if nacelle.Airfoil.naca_4_series_airfoil != None:
if isinstance(
nacelle.Airfoil.naca_4_series_airfoil,
str) and len(nacelle.Airfoil.naca_4_series_airfoil) != 4:
raise AssertionError(
'Nacelle cowling airfoil must be of type < string > and length < 4 >'
)
else:
angle = nacelle.cowling_airfoil_angle / Units.degrees
camber = float(nacelle.Airfoil.naca_4_series_airfoil[0]) / 100
camber_loc = float(
nacelle.Airfoil.naca_4_series_airfoil[1]) / 10
thickness = float(
nacelle.Airfoil.naca_4_series_airfoil[2:]) / 100
vsp.ChangeBORXSecShape(nac_id, vsp.XS_FOUR_SERIES)
vsp.Update()
vsp.SetParmVal(nac_id, "Diameter", "Design", diameter)
vsp.SetParmVal(nac_id, "Angle", "Design", angle)
vsp.SetParmVal(nac_id, "Chord", "XSecCurve", length)
vsp.SetParmVal(nac_id, "ThickChord", "XSecCurve", thickness)
vsp.SetParmVal(nac_id, "Camber", "XSecCurve", camber)
vsp.SetParmVal(nac_id, "CamberLoc", "XSecCurve", camber_loc)
vsp.Update()
else:
vsp.ChangeBORXSecShape(nac_id, vsp.XS_SUPER_ELLIPSE)
vsp.Update()
if ft_flag:
vsp.SetParmVal(nac_id, "Super_Height", "XSecCurve", height)
vsp.SetParmVal(nac_id, "Diameter", "Design", diameter)
else:
vsp.SetParmVal(nac_id, "Super_Height", "XSecCurve", diameter)
vsp.SetParmVal(nac_id, "Super_Width", "XSecCurve", length)
vsp.SetParmVal(nac_id, "Super_MaxWidthLoc", "XSecCurve", 0.)
vsp.SetParmVal(nac_id, "Super_M", "XSecCurve", 2.)
vsp.SetParmVal(nac_id, "Super_N", "XSecCurve", 1.)
vsp.SetSetFlag(nac_id, OML_set_ind, True)
vsp.Update()
return