def _check_firmware_version(gem):
latest_release = git.latest_tag()
build_id = gem.get_firmware_version()
log.info(f"Firmware build ID: {build_id}")
if latest_release in build_id:
return
log.warning("Firmware is out of date, updating it..")
gem.reset_into_bootloader()
path = pathlib.Path(fs.wait_for_drive("GEMINIBOOT", timeout=60 * 5))
fs.copyfile("../firmware/build/gemini-firmware.uf2", path / "firmware.uf2")
fs.flush(path)
time.sleep(3)
log.success("Firmware updated!")
def run(
num_calibration_points,
sample_count,
strategy,
save,
):
if strategy == "adc":
strategy = DirectADCStrategy()
elif strategy == "afe":
strategy = ThroughAFEStrategy()
else:
raise ValueError(f"Unknonw strategy {strategy}.")
# Create the list of calibration points and expected codes.
voltages = [
n / num_calibration_points * strategy.range_
for n in range(num_calibration_points + 1)
]
expected_codes = [
int(voltages[n] / strategy.range_ * (strategy.resolution - 1))
for n in range(num_calibration_points + 1)
]
if strategy.invert:
expected_codes = [
strategy.resolution - 1 - code for code in expected_codes
]
calibration_points = dict(zip(voltages, expected_codes))
gem = gemini.Gemini()
sol_ = sol.Sol()
sol._setup()
sol_.send_voltage(0, channel=strategy.sol_channel)
gem.enter_calibration_mode()
strategy.setup(gem)
measured = _measure_range(gem, sol_, strategy, sample_count,
calibration_points)
gain_error = adc_errors.calculate_avg_gain_error(expected_codes,
list(measured.values()))
offset_error = adc_errors.calculate_avg_offset_error(
expected_codes, list(measured.values()), gain_error)
log.success(f"Measured gain={gain_error:.3f}, offset={offset_error:.1f}")
strategy.finish(gem)
local_copy = pathlib.Path("calibrations") / strategy.file_name(gem)
local_copy.parent.mkdir(parents=True, exist_ok=True)
with local_copy.open("w") as fh:
json.dump({"gain_error": gain_error, "offset_error": offset_error}, fh)
log.info(f"Saved local copy to {local_copy}")
if save:
strategy.save(gem, gain_error, offset_error)
log.success("Saved to NVM.")
else:
log.warning("Dry run, not saving to NVM.")
return
# Test out the new calibration
log.info("Taking measurements with new calibration...")
gem.enable_adc_error_correction()
measured = _measure_range(gem, sol_, strategy, sample_count,
calibration_points)
gain_error = adc_errors.calculate_avg_gain_error(expected_codes,
list(measured.values()))
offset_error = adc_errors.calculate_avg_offset_error(
expected_codes, list(measured.values()), gain_error)
log.info(f"Remeasured gain={gain_error:.3f}, offset={offset_error:.1f}")
log.success("Done")
gem.close()
def run(save):
# Oscilloscope setup.
log.info("Configuring oscilloscope...")
resource_manager = visa.ResourceManager("@ivi")
scope = oscilloscope.Oscilloscope(resource_manager)
scope.reset()
scope.enable_bandwidth_limit()
scope.set_intensity(50, 100)
# Enable both channels initially so that it's clear if the programming
# board isn't connecting to the POGO pins.
scope.set_time_division("10ms")
scope.enable_channel("c1")
scope.enable_channel("c2")
scope.set_vertical_cursor("c1", 0, 3.3)
scope.set_vertical_cursor("c2", 0, 3.3)
scope.set_vertical_division("c1", "800mV")
scope.set_vertical_division("c2", "800mV")
scope.set_vertical_offset("c1", -1.65)
scope.set_vertical_offset("c2", -1.65)
# Gemini setup
log.info("Connecting to Gemini...")
gem = gemini.Gemini()
gem.enter_calibration_mode()
input(
"Connect PROBE ONE to RAMP A\nConnect PROBE TWO to RAMP B\n> press enter to start."
)
# Calibrate both oscillators
log.section("Calibrating Castor...", depth=2)
castor_calibration = _calibrate_oscillator(gem, scope, 0)
lowest_voltage = oscillators.charge_code_to_volts(
min(castor_calibration.values()))
highest_voltage = oscillators.charge_code_to_volts(
max(castor_calibration.values()))
log.success(
f"\nCalibrated:\n- Lowest: {lowest_voltage:.2f}v\n- Highest: {highest_voltage:.2f}v\n"
)
log.section("Calibrating Pollux...", depth=2)
pollux_calibration = _calibrate_oscillator(gem, scope, 1)
lowest_voltage = oscillators.charge_code_to_volts(
min(pollux_calibration.values()))
highest_voltage = oscillators.charge_code_to_volts(
max(pollux_calibration.values()))
log.success(
f"\nCalibrated:\n- Lowest: {lowest_voltage:.2f}v\n- Highest: {highest_voltage:.2f}v\n"
)
log.section("Saving calibration table...", depth=2)
local_copy = pathlib.Path(
"calibrations") / f"{gem.serial_number}.ramp.json"
local_copy.parent.mkdir(parents=True, exist_ok=True)
with local_copy.open("w") as fh:
data = {
"castor": castor_calibration,
"pollux": pollux_calibration,
}
json.dump(data, fh)
log.success(f"Saved local copy to {local_copy}")
if save:
output = tui.Updateable()
bar = tui.Bar()
log.info("Sending LUT values to device...")
with output:
for n, timer_period in enumerate(castor_calibration.keys()):
progress = n / (len(castor_calibration.values()) - 1)
bar.draw(
tui.Segment(
progress,
color=tui.gradient(start_color, end_color, progress),
), )
output.update()
castor_code = castor_calibration[timer_period]
pollux_code = pollux_calibration[timer_period]
gem.write_lut_entry(n, timer_period, castor_code, pollux_code)
log.debug(
f"Set LUT entry {n} to {timer_period=}, {castor_code=}, {pollux_code=}."
)
log.info("Committing LUT to NVM...")
gem.write_lut()
checksum = 0
for dac_code in castor_calibration.values():
checksum ^= dac_code
log.success(f"Calibration table written, checksum: {checksum:04x}")
else:
log.warning("Dry run enabled, calibration table not saved to device.")
gem.close()
print("")
log.success("Done!")
def run(adc_resolution, invert, adc_channel, save):
if invert:
high_expected = 0
low_expected = adc_resolution - 1
else:
high_expected = adc_resolution - 1
low_expected = 0
gem = gemini.Gemini()
gem.enter_calibration_mode()
# Knob calibration is done with error correction enabled.
gem.enable_adc_error_correction()
input(
f"Set knob for channel {adc_channel} all the way CCW and press enter.")
samples = []
for s in range(512):
samples.append(gem.read_adc(adc_channel))
low_measured = statistics.mean(samples)
log.info(f"> Measured {low_measured}, expected {low_expected}")
input(
f"Set knob for channel {adc_channel} all the way CW and press enter.")
samples = []
for s in range(512):
samples.append(gem.read_adc(adc_channel))
high_measured = statistics.mean(samples)
log.info(f"> Measured {high_measured}, expected {high_expected}")
gain_error = (high_expected - low_expected) / (high_measured -
low_measured)
offset_error = (low_measured * gain_error) - low_expected
log.success(
f"Knob gain error: {gain_error:.3f}, offset error: {offset_error:.1f}")
local_copy = pathlib.Path(
"calibrations") / f"{gem.serial_number}.knob.json"
local_copy.parent.mkdir(parents=True, exist_ok=True)
with local_copy.open("w") as fh:
json.dump({"gain_error": gain_error, "offset_error": offset_error}, fh)
log.success(f"Saved local copy to {local_copy}")
if save:
settings = gem.read_settings()
settings.knob_gain_corr = gain_error
settings.knob_offset_corr = offset_error
gem.save_settings(settings)
log.success("Saved to NVM.")
else:
log.warning("Dry run, not saved to NVM.")
log.success("Done!")
gem.close()
def run(
calibration_points,
sample_count,
adc_range,
adc_resolution,
invert,
adc_channel,
save,
):
voltages = [
n / calibration_points * adc_range
for n in range(calibration_points + 1)
]
expected_codes = [
int(voltages[n] / adc_range * (adc_resolution - 1))
for n in range(calibration_points + 1)
]
if invert:
expected_codes = [adc_resolution - 1 - code for code in expected_codes]
measured_codes = []
gem = gemini.Gemini()
sol_ = sol.Sol()
gem.enter_calibration_mode()
gem.disable_adc_error_correction()
sol_.send_voltage(0)
for n in range(calibration_points + 1):
expected = expected_codes[n]
voltage = n / calibration_points * adc_range
log.info(f"Measuring {voltage:.3f}, expecting {expected}.")
sol_.send_voltage(voltage)
time.sleep(0.1)
samples = []
for s in range(sample_count):
samples.append(gem.read_adc(adc_channel))
result = statistics.mean(samples)
diff = result - expected_codes[n]
if abs(diff) > 100:
log.error(
"ADC reading too far out of range. Expected {expected}, measured: {result:.1f}, diff: {diff:.1f}"
)
log.info(f"Measured {result:.1f}, diff {diff:.1f}")
measured_codes.append(result)
gain_error = adc_errors.calculate_avg_gain_error(expected_codes,
measured_codes)
offset_error = adc_errors.calculate_avg_offset_error(
expected_codes, measured_codes, gain_error)
log.info(f"Measured: Gain: {gain_error:.3f}, Offset: {offset_error:.1f}")
corrected = adc_errors.apply_correction(measured_codes, gain_error,
offset_error)
corrected_gain_error = adc_errors.calculate_avg_gain_error(
expected_codes, corrected)
corrected_offset_error = adc_errors.calculate_avg_offset_error(
expected_codes, corrected, corrected_gain_error)
log.success(
f"Expected after correction: Gain: {corrected_gain_error:.3f}, Offset: {corrected_offset_error:.1f}"
)
local_copy = pathlib.Path("calibrations") / f"{gem.serial_number}.adc.json"
local_copy.parent.mkdir(parents=True, exist_ok=True)
with local_copy.open("w") as fh:
json.dump({"gain_error": gain_error, "offset_error": offset_error}, fh)
log.info(f"Saved local copy to {local_copy}")
if save:
gem.set_adc_gain_error(gain_error)
gem.set_adc_offset_error(int(offset_error))
log.success("Saved to NVM.")
else:
log.warning("Dry run, not saved to NVM.")
gem.enable_adc_error_correction()
# Test out the new calibrated ADC
log.info("Taking measurements with new calibration...")
measured_codes = []
for n in range(calibration_points + 1):
voltage = n / calibration_points * adc_range
log.debug(f"Measuring {voltage:.3f}, expecting {expected_codes[n]}.")
sol_.send_voltage(voltage)
time.sleep(0.1)
samples = []
for s in range(sample_count):
samples.append(gem.read_adc(adc_channel))
result = statistics.mean(samples)
log.info(
f"Measured {result:.1f}, diff {result - expected_codes[n]:.1f}")
if abs(diff) > 50:
log.error(
"ADC reading too far out of range. Expected {expected}, measured: {result:.1f}, diff: {diff:.1f}"
)
measured_codes.append(result)
gain_error = adc_errors.calculate_avg_gain_error(expected_codes,
measured_codes)
offset_error = adc_errors.calculate_avg_offset_error(
expected_codes, measured_codes, gain_error)
log.success(
f"Measured, corrected: Gain: {gain_error:.3f}, Offset: {offset_error:.1f}"
)
log.success("Done")
gem.close()