Python register_ble_device 예제들

예제 #1

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield cg.register_component(var, config)
    yield esp32_ble_tracker.register_ble_device(var, config)

    cg.add(var.set_address(config[CONF_MAC_ADDRESS].as_hex))
    cg.add(var.set_constant(config[CONF_CONSTANT]))

    if CONF_AVG_RAW in config:
        sens = yield sensor.new_sensor(config[CONF_AVG_RAW])
        cg.add(var.set_avg_raw(sens))
    if CONF_AVG_W in config:
        sens = yield sensor.new_sensor(config[CONF_AVG_W])
        cg.add(var.set_avg_w(sens))
    if CONF_AVG_DM3 in config:
        sens = yield sensor.new_sensor(config[CONF_AVG_DM3])
        cg.add(var.set_avg_dm3(sens))

    if CONF_TOTAL_RAW in config:
        sens = yield sensor.new_sensor(config[CONF_TOTAL_RAW])
        cg.add(var.set_total_raw(sens))
    if CONF_TOTAL_KWH in config:
        sens = yield sensor.new_sensor(config[CONF_TOTAL_KWH])
        cg.add(var.set_total_kwh(sens))
    if CONF_TOTAL_DM3 in config:
        sens = yield sensor.new_sensor(config[CONF_TOTAL_DM3])
        cg.add(var.set_total_dm3(sens))

    if CONF_BATTERY_LEVEL in config:
        sens = yield sensor.new_sensor(config[CONF_BATTERY_LEVEL])
        cg.add(var.set_battery_level(sens))
    if CONF_LIGHT_LEVEL in config:
        sens = yield sensor.new_sensor(config[CONF_LIGHT_LEVEL])
        cg.add(var.set_light_level(sens))

예제 #2

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield cg.register_component(var, config)
    yield esp32_ble_tracker.register_ble_device(var, config)
    yield sensor.register_sensor(var, config)

    cg.add(var.set_address(config[CONF_MAC_ADDRESS].as_hex))

예제 #3

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield cg.register_component(var, config)
    yield esp32_ble_tracker.register_ble_device(var, config)

    cg.add(var.set_address(config[CONF_MAC_ADDRESS].as_hex))

    if CONF_WEIGHT in config:
        sens = yield sensor.new_sensor(config[CONF_WEIGHT])
        cg.add(var.set_weight(sens))

예제 #4

파일: sensor.py 프로젝트: yevgenb/esphome-1

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield cg.register_component(var, config)
    yield esp32_ble_tracker.register_ble_device(var, config)

    cg.add(var.set_address(config[CONF_MAC_ADDRESS].as_hex))

    if CONF_MOISTURE in config:
        sens = yield sensor.new_sensor(config[CONF_MOISTURE])
        cg.add(var.set_moisture(sens))
    if CONF_CONDUCTIVITY in config:
        sens = yield sensor.new_sensor(config[CONF_CONDUCTIVITY])
        cg.add(var.set_conductivity(sens))

예제 #5

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield cg.register_component(var, config)
    yield esp32_ble_tracker.register_ble_device(var, config)

    cg.add(var.set_address(config[CONF_MAC_ADDRESS].as_hex))

    if CONF_TEMPERATURE in config:
        sens = yield sensor.new_sensor(config[CONF_TEMPERATURE])
        cg.add(var.set_temperature(sens))
    if CONF_HUMIDITY in config:
        sens = yield sensor.new_sensor(config[CONF_HUMIDITY])
        cg.add(var.set_humidity(sens))

예제 #6

파일: binary_sensor.py 프로젝트: SciFiFarms/TechnoCore-ESPHome

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield cg.register_component(var, config)
    yield esp32_ble_tracker.register_ble_device(var, config)
    yield binary_sensor.register_binary_sensor(var, config)

    cg.add(var.set_address(config[CONF_MAC_ADDRESS].as_hex))

    if CONF_TABLET in config:
        sens = yield sensor.new_sensor(config[CONF_TABLET])
        cg.add(var.set_tablet(sens))
    if CONF_BATTERY_LEVEL in config:
        sens = yield sensor.new_sensor(config[CONF_BATTERY_LEVEL])
        cg.add(var.set_battery_level(sens))

예제 #7

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield cg.register_component(var, config)
    yield esp32_ble_tracker.register_ble_device(var, config)

    cg.add(var.set_address(config[CONF_MAC_ADDRESS].as_hex))

    for (config_key, setter) in [
        (CONF_TEMPERATURE, var.set_temperature),
        (CONF_HUMIDITY, var.set_humidity),
        (CONF_BATTERY_VOLTAGE, var.set_battery_voltage),
        (CONF_MOISTURE, var.set_soil_moisture),
    ]:
        if config_key in config:
            sens = yield sensor.new_sensor(config[config_key])
            cg.add(setter(sens))

예제 #8

파일: binary_sensor.py 프로젝트: dentra/esphome-components

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield cg.register_component(var, config)
    yield esp32_ble_tracker.register_ble_device(var, config)

    cg.add(var.set_address(config[CONF_MAC_ADDRESS].as_hex))
    cg.add(var.set_bindkey(config[CONF_BINDKEY]))

    if CONF_LIGHT in config:
        sens = yield binary_sensor.new_binary_sensor(config[CONF_LIGHT])
        cg.add(var.set_light(sens))
    if CONF_OPEN in config:
        sens = yield binary_sensor.new_binary_sensor(config[CONF_OPEN])
        cg.add(var.set_open(sens))
    if CONF_BATTERY_LEVEL in config:
        sens = yield sensor.new_sensor(config[CONF_BATTERY_LEVEL])
        cg.add(var.set_battery_level(sens))

예제 #9

파일: binary_sensor.py 프로젝트: wjcarpenter/mvturnho_esphome_ili9341

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield cg.register_component(var, config)
    yield esp32_ble_tracker.register_ble_device(var, config)
    yield binary_sensor.register_binary_sensor(var, config)

    if CONF_MAC_ADDRESS in config:
        cg.add(var.set_address(config[CONF_MAC_ADDRESS].as_hex))

    if CONF_SERVICE_UUID in config:
        if len(config[CONF_SERVICE_UUID]) == len(esp32_ble_tracker.bt_uuid16_format):
            cg.add(var.set_service_uuid16(esp32_ble_tracker.as_hex(config[CONF_SERVICE_UUID])))
        elif len(config[CONF_SERVICE_UUID]) == len(esp32_ble_tracker.bt_uuid32_format):
            cg.add(var.set_service_uuid32(esp32_ble_tracker.as_hex(config[CONF_SERVICE_UUID])))
        elif len(config[CONF_SERVICE_UUID]) == len(esp32_ble_tracker.bt_uuid128_format):
            uuid128 = esp32_ble_tracker.as_hex_array(config[CONF_SERVICE_UUID])
            cg.add(var.set_service_uuid128(uuid128))

예제 #10

파일: binary_sensor.py 프로젝트: ielbury/esphome

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield cg.register_component(var, config)
    yield esp32_ble_tracker.register_ble_device(var, config)
    yield binary_sensor.register_binary_sensor(var, config)

    cg.add(var.set_address(config[CONF_MAC_ADDRESS].as_hex))
    cg.add(var.set_bindkey(config[CONF_BINDKEY]))

    if CONF_IDLE_TIME in config:
        sens = yield sensor.new_sensor(config[CONF_IDLE_TIME])
        cg.add(var.set_idle_time(sens))
    if CONF_BATTERY_LEVEL in config:
        sens = yield sensor.new_sensor(config[CONF_BATTERY_LEVEL])
        cg.add(var.set_battery_level(sens))
    if CONF_ILLUMINANCE in config:
        sens = yield sensor.new_sensor(config[CONF_ILLUMINANCE])
        cg.add(var.set_illuminance(sens))

예제 #11

파일: sensor.py 프로젝트: wjcarpenter/mvturnho_esphome_ili9341

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield cg.register_component(var, config)
    yield esp32_ble_tracker.register_ble_device(var, config)

    cg.add(var.set_address(config[CONF_MAC_ADDRESS].as_hex))

    if CONF_TEMPERATURE in config:
        sens = yield sensor.new_sensor(config[CONF_TEMPERATURE])
        cg.add(var.set_temperature(sens))
    if CONF_HUMIDITY in config:
        sens = yield sensor.new_sensor(config[CONF_HUMIDITY])
        cg.add(var.set_humidity(sens))
    if CONF_PRESSURE in config:
        sens = yield sensor.new_sensor(config[CONF_PRESSURE])
        cg.add(var.set_pressure(sens))
    if CONF_ACCELERATION in config:
        sens = yield sensor.new_sensor(config[CONF_ACCELERATION])
        cg.add(var.set_acceleration(sens))
    if CONF_ACCELERATION_X in config:
        sens = yield sensor.new_sensor(config[CONF_ACCELERATION_X])
        cg.add(var.set_acceleration_x(sens))
    if CONF_ACCELERATION_Y in config:
        sens = yield sensor.new_sensor(config[CONF_ACCELERATION_Y])
        cg.add(var.set_acceleration_y(sens))
    if CONF_ACCELERATION_Z in config:
        sens = yield sensor.new_sensor(config[CONF_ACCELERATION_Z])
        cg.add(var.set_acceleration_z(sens))
    if CONF_BATTERY_VOLTAGE in config:
        sens = yield sensor.new_sensor(config[CONF_BATTERY_VOLTAGE])
        cg.add(var.set_battery_voltage(sens))
    if CONF_TX_POWER in config:
        sens = yield sensor.new_sensor(config[CONF_TX_POWER])
        cg.add(var.set_tx_power(sens))
    if CONF_MOVEMENT_COUNTER in config:
        sens = yield sensor.new_sensor(config[CONF_MOVEMENT_COUNTER])
        cg.add(var.set_movement_counter(sens))
    if CONF_MEASUREMENT_SEQUENCE_NUMBER in config:
        sens = yield sensor.new_sensor(
            config[CONF_MEASUREMENT_SEQUENCE_NUMBER])
        cg.add(var.set_measurement_sequence_number(sens))

예제 #12

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield cg.register_component(var, config)
    yield esp32_ble_tracker.register_ble_device(var, config)

    cg.add(var.set_address(config[CONF_MAC_ADDRESS].as_hex))

    if CONF_TEMPERATURE in config:
        sens = yield sensor.new_sensor(config[CONF_TEMPERATURE])
        cg.add(var.set_temperature(sens))
    if CONF_MOISTURE in config:
        sens = yield sensor.new_sensor(config[CONF_MOISTURE])
        cg.add(var.set_moisture(sens))
    if CONF_ILLUMINANCE in config:
        sens = yield sensor.new_sensor(config[CONF_ILLUMINANCE])
        cg.add(var.set_illuminance(sens))
    if CONF_CONDUCTIVITY in config:
        sens = yield sensor.new_sensor(config[CONF_CONDUCTIVITY])
        cg.add(var.set_conductivity(sens))
    if CONF_BATTERY_LEVEL in config:
        sens = yield sensor.new_sensor(config[CONF_BATTERY_LEVEL])
        cg.add(var.set_battery_level(sens))

예제 #13

파일: __init__.py 프로젝트: SciFiFarms/TechnoCore-ESPHome

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield esp32_ble_tracker.register_ble_device(var, config)

예제 #14

def to_code(config):
    var = cg.new_Pvariable(config[CONF_ID])
    yield cg.register_component(var, config)
    yield esp32_ble_tracker.register_ble_device(var, config)
    yield text_sensor.register_text_sensor(var, config)

예제 #15

파일: __init__.py 프로젝트: SciFiFarms/TechnoCore-ESPHome

def to_code(config):
    for conf in config.get(CONF_ON_EXPOSURE_NOTIFICATION, []):
        trigger = cg.new_Pvariable(conf[CONF_TRIGGER_ID])
        yield automation.build_automation(trigger, [(ExposureNotification, "x")], conf)
        yield esp32_ble_tracker.register_ble_device(trigger, conf)