def get_extruders(self):
"""
Populate extruder list
:return:
"""
for i in range(len(self.extruder_name)):
t = self.extruder_tool[i]
name = self.extruder_name[i]
ext = Extruder(t, name=name)
ext.nozzle = self.extruder_diameter[i]
if self.extruder_use_retract[i]:
ext.retract = self.extruder_retract_dist[i]
ext.retract_speed = self.extruder_retract_speed[i]
ext.z_hop = self.extruder_zhop[i]
if self.extruder_use_coasting[i]:
ext.coasting = self.extruder_coasting[i]
if self.extruder_use_wipe[i]:
ext.wipe = self.extruder_wipe[i]
ext.feed_rate_multiplier = self.extruder_multiplier[i]
ext.temperature_nr = self.temperature_numbers[i]
for j in range(self.temperature_setpoints[i]):
index = self.temperature_setpoints[i] * i + j
layer_nr = self.temperature_setpoint_layers[index]
ext.temperature_setpoints[
layer_nr] = self.temperature_setpoint_temps[index]
self.extruders[t] = ext
def get_extruders(self):
"""
Populate extruder list
:return:
"""
for i in range(len(self.extruder_name)):
t = self.extruder_tool[i]
name = self.extruder_name[i]
ext = Extruder(t, name=name)
ext.nozzle = self.extruder_diameter[i]
if self.extruder_use_retract[i]:
ext.retract = self.extruder_retract_dist[i]
ext.retract_speed = self.extruder_retract_speed[i]
ext.z_hop = self.extruder_zhop[i]
if self.extruder_use_coasting[i]:
ext.coasting = self.extruder_coasting[i]
if self.extruder_use_wipe[i]:
ext.wipe = self.extruder_wipe[i]
ext.feed_rate_multiplier = self.extruder_multiplier[i]
ext.extrusion_width = self.extruder_widths[i]
self.extruders[t] = ext
# go through the temperature names and try to assign them to extruders
temp_setpoint_index = 0
for i in range(len(self.temperature_names)):
t = self.temperature_numbers[i]
if self.temperature_heated_bed[i] == 0:
ext = self.extruders[t]
ext.temperature_nr = t
else:
ext = None
# need to parse all setpoints to keep proper indexing even with bed
for j in range(self.temperature_setpoints[i]):
if ext:
layer_nr = self.temperature_setpoint_layers[temp_setpoint_index]
ext.temperature_setpoints[layer_nr] = self.temperature_setpoint_temps[temp_setpoint_index]
temp_setpoint_index += 1
# find proper setpoint temp
last_setpoints = None
for e in self.extruders:
# setpoints
if self.extruders[e].temperature_setpoints:
last_setpoints = self.extruders[e].temperature_setpoints
break
# if not found, bad config
if not last_setpoints:
raise ValueError("Could not find valid temperature settings for extruder(s). Please check S3D profile")
warning = False
for e in self.extruders:
if not self.extruders[e].temperature_setpoints:
self.extruders[e].temperature_setpoints = last_setpoints
warning = True
# temp nr. Use tool number if not defined
if self.extruders[e].temperature_nr is None:
self.extruders[e].temperature_nr = self.extruders[e].tool
# debug
# for e in self.extruders:
# print(self.extruders[e].temperature_nr, self.extruders[e].temperature_setpoints)
if warning:
self.log.info("Not all extruders have valid temperature definitions, using previous extruder values. Please check profile temperature settings")
