def main():
args = example_utils.ExampleArgumentParser().parse_args()
example_utils.config_logging(args)
if args.socket_addr:
client = SocketClient(args.socket_addr)
elif args.spi:
client = SPIClient()
else:
port = args.serial_port or example_utils.autodetect_serial_port()
client = UARTClient(port)
client.squeeze = False
config = configs.EnvelopeServiceConfig()
config.sensor = args.sensors
config.range_interval = [0.3, 0.8]
config.sweep_rate = 70
config.gain = 0.6
# config.experimental_stitching = True
# config.session_profile = configs.EnvelopeServiceConfig.MAX_SNR
# config.running_average_factor = 0.5
# config.compensate_phase = False # not recommended
info = client.setup_session(config)
num_points = info["data_length"]
pg_updater = PGUpdater(config, num_points)
pg_process = PGProcess(pg_updater)
pg_process.start()
client.start_streaming()
interrupt_handler = example_utils.ExampleInterruptHandler()
print("Press Ctrl-C to end session")
while not interrupt_handler.got_signal:
info, data = client.get_next()
try:
pg_process.put_data(data)
print(data)
input("Enter")
except PGProccessDiedException:
break
print("Disconnecting...")
pg_process.close()
client.disconnect()
def main():
args = example_utils.ExampleArgumentParser().parse_args()
example_utils.config_logging(args)
if args.socket_addr:
client = SocketClient(args.socket_addr)
elif args.spi:
client = SPIClient()
else:
port = args.serial_port or example_utils.autodetect_serial_port()
client = UARTClient(port)
client.squeeze = False
config = configs.IQServiceConfig()
config.sensor = args.sensors
config.range_interval = [0.2, 0.6]
config.sweep_rate = 30
config.gain = 0.6
# config.running_average_factor = 0.5
info = client.setup_session(config)
num_points = info["data_length"]
fig_updater = ExampleFigureUpdater(config, num_points)
plot_process = PlotProcess(fig_updater)
plot_process.start()
client.start_streaming()
interrupt_handler = example_utils.ExampleInterruptHandler()
print("Press Ctrl-C to end session")
while not interrupt_handler.got_signal:
info, data = client.get_next()
plot_data = {
"amplitude": np.abs(data),
"phase": np.angle(data),
}
try:
plot_process.put_data(plot_data)
except PlotProccessDiedException:
break
print("Disconnecting...")
plot_process.close()
client.disconnect()
def main():
args = example_utils.ExampleArgumentParser().parse_args()
example_utils.config_logging(args)
if args.socket_addr:
client = SocketClient(args.socket_addr)
elif args.spi:
client = SPIClient()
else:
port = args.serial_port or example_utils.autodetect_serial_port()
client = UARTClient(port)
client.squeeze = False
config = configs.IQServiceConfig()
config.sensor = args.sensors
config.range_interval = [0.2, 0.6]
config.sweep_rate = 30
config.gain = 0.6
config.sampling_mode = config.SAMPLING_MODE_A
# config.running_average_factor = 0.5
# config.hw_accelerated_average_samples = 7
# config.stepsize = 1
info = client.setup_session(config)
num_points = info["data_length"]
pg_updater = PGUpdater(config, num_points)
pg_process = PGProcess(pg_updater)
pg_process.start()
client.start_streaming()
interrupt_handler = example_utils.ExampleInterruptHandler()
print("Press Ctrl-C to end session")
while not interrupt_handler.got_signal:
info, data = client.get_next()
try:
pg_process.put_data(data)
except PGProccessDiedException:
break
print("Disconnecting...")
pg_process.close()
client.disconnect()
def main():
args = example_utils.ExampleArgumentParser().parse_args()
example_utils.config_logging(args)
if args.socket_addr:
client = SocketClient(args.socket_addr)
elif args.spi:
client = SPIClient()
else:
port = args.serial_port or example_utils.autodetect_serial_port()
client = UARTClient(port)
client.squeeze = False
sensor_config = get_sensor_config()
sensor_config.sensor = args.sensors
processing_config = get_processing_config()
session_info = client.setup_session(sensor_config)
pg_updater = PGUpdater(sensor_config, processing_config, session_info)
pg_process = PGProcess(pg_updater)
pg_process.start()
client.start_streaming()
interrupt_handler = example_utils.ExampleInterruptHandler()
print("Press Ctrl-C to end session")
processor = Processor(sensor_config, processing_config, session_info)
while not interrupt_handler.got_signal:
info, sweep = client.get_next()
plot_data = processor.process(sweep)
if plot_data is not None:
try:
pg_process.put_data(plot_data)
except PGProccessDiedException:
break
print("Disconnecting...")
pg_process.close()
client.disconnect()
def main():
args = example_utils.ExampleArgumentParser().parse_args()
example_utils.config_logging(args)
if args.socket_addr:
client = SocketClient(args.socket_addr)
elif args.spi:
client = SPIClient()
else:
port = args.serial_port or example_utils.autodetect_serial_port()
client = UARTClient(port)
client.squeeze = False
config = configs.SparseServiceConfig()
config.sensor = args.sensors
config.range_interval = [0.24, 1.20]
config.sweep_rate = 60
config.number_of_subsweeps = 16
# config.hw_accelerated_average_samples = 60
# config.stepsize = 1
client.setup_session(config)
pg_updater = PGUpdater(config)
pg_process = PGProcess(pg_updater)
pg_process.start()
client.start_streaming()
interrupt_handler = example_utils.ExampleInterruptHandler()
print("Press Ctrl-C to end session")
while not interrupt_handler.got_signal:
info, data = client.get_next()
try:
pg_process.put_data(data)
except PGProccessDiedException:
break
print("Disconnecting...")
pg_process.close()
client.disconnect()
