def set_dac_mu(self, values, channels=list(range(40))):
"""Program multiple DAC channels and pulse LDAC to update the DAC
outputs.
This method does not advance the timeline; write events are scheduled
in the past. The DACs will synchronously start changing their output
levels `now`.
If no LDAC device was defined, the LDAC pulse is skipped.
See :meth load:.
:param values: list of DAC values to program
:param channels: list of DAC channels to program. If not specified,
we program the DAC channels sequentially, starting at 0.
"""
t0 = now_mu()
# t10: max busy period after writing to DAC registers
t_10 = self.core.seconds_to_mu(1500 * ns)
# compensate all delays that will be applied
delay_mu(-t_10 - len(values) * self.bus.xfer_duration_mu)
for i in range(len(values)):
self.write_dac_mu(channels[i], values[i])
delay_mu(t_10)
self.load()
at_mu(t0)
def set_dac_mu(self, values, channels=list(range(40))):
"""Program multiple DAC channels and pulse LDAC to update the DAC
outputs.
This method does not advance the timeline; write events are scheduled
in the past. The DACs will synchronously start changing their output
levels `now`.
If no LDAC device was defined, the LDAC pulse is skipped.
See :meth load:.
:param values: list of DAC values to program
:param channels: list of DAC channels to program. If not specified,
we program the DAC channels sequentially, starting at 0.
"""
t0 = now_mu()
# t10: max busy period after writing to DAC registers
t_10 = self.core.seconds_to_mu(1500*ns)
# compensate all delays that will be applied
delay_mu(-t_10-len(values)*self.bus.xfer_duration_mu)
for i in range(len(values)):
self.write_dac_mu(channels[i], values[i])
delay_mu(t_10)
self.load()
at_mu(t0)
def set_mu(self,
ftw,
pow_=0,
asf=0x3fff,
phase_mode=_PHASE_MODE_DEFAULT,
ref_time_mu=int64(-1),
profile=0):
"""Set profile 0 data in machine units.
This uses machine units (FTW, POW, ASF). The frequency tuning word
width is 32, the phase offset word width is 16, and the amplitude
scale factor width is 12.
After the SPI transfer, the shared IO update pin is pulsed to
activate the data.
.. seealso: :meth:`set_phase_mode` for a definition of the different
phase modes.
:param ftw: Frequency tuning word: 32 bit.
:param pow_: Phase tuning word: 16 bit unsigned.
:param asf: Amplitude scale factor: 14 bit unsigned.
:param phase_mode: If specified, overrides the default phase mode set
by :meth:`set_phase_mode` for this call.
:param ref_time_mu: Fiducial time used to compute absolute or tracking
phase updates. In machine units as obtained by `now_mu()`.
:param profile: Profile number to set (0-7, default: 0).
:return: Resulting phase offset word after application of phase
tracking offset. When using :const:`PHASE_MODE_CONTINUOUS` in
subsequent calls, use this value as the "current" phase.
"""
if phase_mode == _PHASE_MODE_DEFAULT:
phase_mode = self.phase_mode
# Align to coarse RTIO which aligns SYNC_CLK. I.e. clear fine TSC
# This will not cause a collision or sequence error.
at_mu(now_mu() & ~7)
if phase_mode != PHASE_MODE_CONTINUOUS:
# Auto-clear phase accumulator on IO_UPDATE.
# This is active already for the next IO_UPDATE
self.set_cfr1(phase_autoclear=1)
if phase_mode == PHASE_MODE_TRACKING and ref_time_mu < 0:
# set default fiducial time stamp
ref_time_mu = 0
if ref_time_mu >= 0:
# 32 LSB are sufficient.
# Also no need to use IO_UPDATE time as this
# is equivalent to an output pipeline latency.
dt = int32(now_mu()) - int32(ref_time_mu)
pow_ += dt * ftw * self.sysclk_per_mu >> 16
self.write64(_AD9910_REG_PROFILE0 + profile,
(asf << 16) | (pow_ & 0xffff), ftw)
delay_mu(int64(self.sync_data.io_update_delay))
self.cpld.io_update.pulse_mu(8) # assumes 8 mu > t_SYN_CCLK
at_mu(now_mu() & ~7) # clear fine TSC again
if phase_mode != PHASE_MODE_CONTINUOUS:
self.set_cfr1()
# future IO_UPDATE will activate
return pow_
def test_at_mu(self):
for i in range(_NUM_SAMPLES):
with self.subTest('at_mu() sub test', i=i):
# Random time
ref_time = self.rnd.randrange(1000000000)
# Set time
at_mu(ref_time)
# Compare time
self.assertEqual(now_mu(), ref_time, 'Reference does not match now_mu()')
def set_mu(self, ftw, pow_=0, asf=0x3fff, phase_mode=_PHASE_MODE_DEFAULT,
ref_time_mu=int64(-1), profile=0):
"""Set profile 0 data in machine units.
This uses machine units (FTW, POW, ASF). The frequency tuning word
width is 32, the phase offset word width is 16, and the amplitude
scale factor width is 12.
After the SPI transfer, the shared IO update pin is pulsed to
activate the data.
.. seealso: :meth:`set_phase_mode` for a definition of the different
phase modes.
:param ftw: Frequency tuning word: 32 bit.
:param pow_: Phase tuning word: 16 bit unsigned.
:param asf: Amplitude scale factor: 14 bit unsigned.
:param phase_mode: If specified, overrides the default phase mode set
by :meth:`set_phase_mode` for this call.
:param ref_time_mu: Fiducial time used to compute absolute or tracking
phase updates. In machine units as obtained by `now_mu()`.
:param profile: Profile number to set (0-7, default: 0).
:return: Resulting phase offset word after application of phase
tracking offset. When using :const:`PHASE_MODE_CONTINUOUS` in
subsequent calls, use this value as the "current" phase.
"""
if phase_mode == _PHASE_MODE_DEFAULT:
phase_mode = self.phase_mode
# Align to coarse RTIO which aligns SYNC_CLK. I.e. clear fine TSC
# This will not cause a collision or sequence error.
at_mu(now_mu() & ~7)
if phase_mode != PHASE_MODE_CONTINUOUS:
# Auto-clear phase accumulator on IO_UPDATE.
# This is active already for the next IO_UPDATE
self.set_cfr1(phase_autoclear=1)
if phase_mode == PHASE_MODE_TRACKING and ref_time_mu < 0:
# set default fiducial time stamp
ref_time_mu = 0
if ref_time_mu >= 0:
# 32 LSB are sufficient.
# Also no need to use IO_UPDATE time as this
# is equivalent to an output pipeline latency.
dt = int32(now_mu()) - int32(ref_time_mu)
pow_ += dt*ftw*self.sysclk_per_mu >> 16
self.write64(_AD9910_REG_PROFILE0 + profile,
(asf << 16) | (pow_ & 0xffff), ftw)
delay_mu(int64(self.io_update_delay))
self.cpld.io_update.pulse_mu(8) # assumes 8 mu > t_SYN_CCLK
at_mu(now_mu() & ~7) # clear fine TSC again
if phase_mode != PHASE_MODE_CONTINUOUS:
self.set_cfr1()
# future IO_UPDATE will activate
return pow_
def measure_io_update_alignment(self, delay_start: TInt64,
delay_stop: TInt64) -> TInt32:
"""Use the digital ramp generator to locate the alignment between
IO_UPDATE and SYNC_CLK.
The ramp generator is set up to a linear frequency ramp
(dFTW/t_SYNC_CLK=1) and started at a coarse RTIO time stamp plus
`delay_start` and stopped at a coarse RTIO time stamp plus
`delay_stop`.
:param delay_start: Start IO_UPDATE delay in machine units.
:param delay_stop: Stop IO_UPDATE delay in machine units.
:return: Odd/even SYNC_CLK cycle indicator.
"""
# set up DRG
self.set_cfr1(drg_load_lrr=1, drg_autoclear=1)
# DRG -> FTW, DRG enable
self.set_cfr2(drg_enable=1)
# no limits
self.write64(_AD9910_REG_RAMP_LIMIT, -1, 0)
# DRCTL=0, dt=1 t_SYNC_CLK
self.write32(_AD9910_REG_RAMP_RATE, 0x00010000)
# dFTW = 1, (work around negative slope)
self.write64(_AD9910_REG_RAMP_STEP, -1, 0)
# delay io_update after RTIO edge
t = now_mu() + 8 & ~7
at_mu(t + delay_start)
# assumes a maximum t_SYNC_CLK period
self.cpld.io_update.pulse_mu(16 - delay_start) # realign
# disable DRG autoclear and LRR on io_update
self.set_cfr1()
# stop DRG
self.write64(_AD9910_REG_RAMP_STEP, 0, 0)
at_mu(t + 0x1000 + delay_stop)
self.cpld.io_update.pulse_mu(16 - delay_stop) # realign
ftw = self.read32(_AD9910_REG_FTW) # read out effective FTW
delay(100 * us) # slack
# disable DRG
self.set_cfr2(drg_enable=0)
self.cpld.io_update.pulse_mu(8)
return ftw & 1
def measure_io_update_alignment(self, delay_start, delay_stop):
"""Use the digital ramp generator to locate the alignment between
IO_UPDATE and SYNC_CLK.
The ramp generator is set up to a linear frequency ramp
(dFTW/t_SYNC_CLK=1) and started at a coarse RTIO time stamp plus
`delay_start` and stopped at a coarse RTIO time stamp plus
`delay_stop`.
:param delay_start: Start IO_UPDATE delay in machine units.
:param delay_stop: Stop IO_UPDATE delay in machine units.
:return: Odd/even SYNC_CLK cycle indicator.
"""
# set up DRG
self.set_cfr1(drg_load_lrr=1, drg_autoclear=1)
# DRG -> FTW, DRG enable
self.write32(_AD9910_REG_CFR2, 0x01090000)
# no limits
self.write64(_AD9910_REG_RAMP_LIMIT, -1, 0)
# DRCTL=0, dt=1 t_SYNC_CLK
self.write32(_AD9910_REG_RAMP_RATE, 0x00010000)
# dFTW = 1, (work around negative slope)
self.write64(_AD9910_REG_RAMP_STEP, -1, 0)
# delay io_update after RTIO edge
t = now_mu() + 8 & ~7
at_mu(t + delay_start)
# assumes a maximum t_SYNC_CLK period
self.cpld.io_update.pulse_mu(16 - delay_start) # realign
# disable DRG autoclear and LRR on io_update
self.set_cfr1()
# stop DRG
self.write64(_AD9910_REG_RAMP_STEP, 0, 0)
at_mu(t + 0x1000 + delay_stop)
self.cpld.io_update.pulse_mu(16 - delay_stop) # realign
ftw = self.read32(_AD9910_REG_FTW) # read out effective FTW
delay(100*us) # slack
# disable DRG
self.write32(_AD9910_REG_CFR2, 0x01010000)
self.cpld.io_update.pulse_mu(8)
return ftw & 1
def measure_io_update_alignment(self, delay_start, delay_stop):
"""Use the digital ramp generator to locate the alignment between
IO_UPDATE and SYNC_CLK.
The ramp generator is set up to a linear frequency ramp
(dFTW/t_SYNC_CLK=1) and started at a coarse RTIO time stamp plus
`delay_start` and stopped at a coarse RTIO time stamp plus
`delay_stop`.
:param delay_start: Start IO_UPDATE delay in machine units.
:param delay_stop: Stop IO_UPDATE delay in machine units.
:return: Odd/even SYNC_CLK cycle indicator.
"""
# set up DRG
# DRG ACC autoclear and LRR on io update
self.write32(_AD9910_REG_CFR1, 0x0000c002)
# DRG -> FTW, DRG enable
self.write32(_AD9910_REG_CFR2, 0x01090000)
# no limits
self.write64(_AD9910_REG_RAMP_LIMIT, -1, 0)
# DRCTL=0, dt=1 t_SYNC_CLK
self.write32(_AD9910_REG_RAMP_RATE, 0x00010000)
# dFTW = 1, (work around negative slope)
self.write64(_AD9910_REG_RAMP_STEP, -1, 0)
# delay io_update after RTIO/2 edge
t = now_mu() + 0x10 & ~0xf
at_mu(t + delay_start)
self.cpld.io_update.pulse_mu(32 - delay_start) # realign
# disable DRG autoclear and LRR on io_update
self.write32(_AD9910_REG_CFR1, 0x00000002)
# stop DRG
self.write64(_AD9910_REG_RAMP_STEP, 0, 0)
at_mu(t + 0x1000 + delay_stop)
self.cpld.io_update.pulse_mu(32 - delay_stop) # realign
ftw = self.read32(_AD9910_REG_FTW) # read out effective FTW
delay(100 * us) # slack
# disable DRG
self.write32(_AD9910_REG_CFR2, 0x01010000)
self.cpld.io_update.pulse_mu(8)
return ftw & 1
def set(self, values, op=_AD5360_CMD_DATA):
"""Write to several channels and pulse LDAC to update the channels.
This method does not advance the timeline. Write events are scheduled
in the past. The DACs will synchronously start changing their output
levels `now`.
:param values: List of 16 bit values to write to the channels.
:param op: Operation to perform, one of :const:`_AD5360_CMD_DATA`,
:const:`_AD5360_CMD_OFFSET`, :const:`_AD5360_CMD_GAIN`
(default: :const:`_AD5360_CMD_DATA`).
"""
t0 = now_mu()
# t10 max busy low for one channel
t_10 = self.core.seconds_to_mu(1.5 * us)
# compensate all delays that will be applied
delay_mu(-len(values) * self.bus.xfer_period_mu - t_10)
for i in range(len(values)):
self.write_channel(i, values[i], op)
delay_mu(t_10)
self.load()
at_mu(t0)
def init(self, blind=False):
"""Initialize and detect Urukul.
Resets the DDS I/O interface and verifies correct CPLD gateware
version.
Does not pulse the DDS MASTER_RESET as that confuses the AD9910.
:param blind: Do not attempt to verify presence and compatibility.
"""
cfg = self.cfg_reg
# Don't pulse MASTER_RESET (m-labs/artiq#940)
self.cfg_reg = cfg | (0 << CFG_RST) | (1 << CFG_IO_RST)
if blind:
self.cfg_write(self.cfg_reg)
else:
proto_rev = urukul_sta_proto_rev(self.sta_read())
if proto_rev != STA_PROTO_REV_MATCH:
raise ValueError("Urukul proto_rev mismatch")
delay(100 * us) # reset, slack
self.cfg_write(cfg)
if self.sync_div:
at_mu(now_mu() & ~0xf) # align to RTIO/2
self.set_sync_div(self.sync_div) # 125 MHz/2 = 1 GHz/16
delay(1 * ms) # DDS wake up
def init(self, blind=False):
"""Initialize and detect Urukul.
Resets the DDS I/O interface and verifies correct CPLD gateware
version.
Does not pulse the DDS MASTER_RESET as that confuses the AD9910.
:param blind: Do not attempt to verify presence and compatibility.
"""
cfg = self.cfg_reg
# Don't pulse MASTER_RESET (m-labs/artiq#940)
self.cfg_reg = cfg | (0 << CFG_RST) | (1 << CFG_IO_RST)
if blind:
self.cfg_write(self.cfg_reg)
else:
proto_rev = urukul_sta_proto_rev(self.sta_read())
if proto_rev != STA_PROTO_REV_MATCH:
raise ValueError("Urukul proto_rev mismatch")
delay(100*us) # reset, slack
self.cfg_write(cfg)
if self.sync_div:
at_mu(now_mu() & ~0xf) # align to RTIO/2
self.set_sync_div(self.sync_div) # 125 MHz/2 = 1 GHz/16
delay(1*ms) # DDS wake up
def test_manual_deep_parallel(self):
# Manual deep parallel matches the timing model of ARTIQ, see https://github.com/m-labs/artiq/issues/1555
for i in range(_NUM_SAMPLES):
with self.subTest('parallel sub test', i=i):
# Reference time
ref_time = now_mu()
# Block duration
block_duration = 0
# Single random duration
duration = self.rnd.randrange(1000000000)
for _ in range(10):
at_mu(ref_time) # Manually revert timeline for deep parallel emulation
# Delay
delay_mu(duration)
# Update block duration
block_duration = max(duration, block_duration)
# Update ref time
ref_time += block_duration
# Compare to reference time
self.assertEqual(now_mu(), ref_time, 'Reference does not match now_mu()')
def timestamp_mu(self):
result = time.manager.get_time_mu()
result += self.prng.randrange(100, 1000)
time.manager.event(("timestamp_mu", self.name, result))
at_mu(result)
return result
def run_daq(self, duration, daqs, chunk=200):
self.core.break_realtime()
self.trigger_controller.reset.off()
at_mu(now_mu() + self.core.seconds_to_mu(duration))
self.trigger_controller.reset.on()
self.daq_transfer_loop(daqs, duration, chunk)
