def run(self):
# Deletes previous saved data
if os.path.isfile("projects/tut_randkey_randplain.cwp"): os.remove("projects/tut_randkey_randplain.cwp")
shutil.rmtree("projects/tut_randkey_randplain_data", ignore_errors=True)
if os.path.isfile("projects/tut_fixedkey_randplain.cwp"): os.remove("projects/tut_fixedkey_randplain.cwp")
shutil.rmtree("projects/tut_fixedkey_randplain_data", ignore_errors=True)
# Setup the capture hardware
self.api.setParameter(['Generic Settings', 'Scope Module', 'ChipWhisperer/OpenADC'])
self.api.setParameter(['Generic Settings', 'Target Module', 'Simple Serial'])
self.api.setParameter(['Generic Settings', 'Trace Format', 'ChipWhisperer/Native'])
self.api.setParameter(['Simple Serial', 'Connection', 'NewAE USB (CWLite/CW1200)'])
self.api.setParameter(['ChipWhisperer/OpenADC', 'Connection', 'NewAE USB (CWLite/CW1200)'])
# Conect both: scope and target
self.api.connect()
# Flash the firmware
xmega = XMEGAProgrammer()
xmega.setUSBInterface(self.api.getScope().scopetype.dev.xmega)
xmega._logging = None
xmega.find()
xmega.erase()
xmega.program(r"simpleserial-aes-xmega.hex", memtype="flash", verify=True)
xmega.close()
# Setup the capture parameters
lstexample = [['CW Extra Settings', 'Trigger Pins', 'Target IO4 (Trigger Line)', True],
['CW Extra Settings', 'Target IOn Pins', 'Target IO1', 'Serial RXD'],
['CW Extra Settings', 'Target IOn Pins', 'Target IO2', 'Serial TXD'],
['OpenADC', 'Clock Setup', 'CLKGEN Settings', 'Desired Frequency', 7370000.0],
['CW Extra Settings', 'Target HS IO-Out', 'CLKGEN'],
['OpenADC', 'Clock Setup', 'ADC Clock', 'Source', 'CLKGEN x4 via DCM'],
['OpenADC', 'Trigger Setup', 'Total Samples', 3000],
['OpenADC', 'Trigger Setup', 'Offset', 1250],
['OpenADC', 'Gain Setting', 'Setting', 45],
['OpenADC', 'Trigger Setup', 'Mode', 'rising edge'],
#Final step: make DCMs relock in case they are lost
['OpenADC', 'Clock Setup', 'ADC Clock', 'Reset ADC DCM', None],
]
for cmd in lstexample: self.api.setParameter(cmd)
# Capture a set of traces with random key and save the project
self.api.setParameter(['Generic Settings', 'Basic', 'Key', 'Random'])
self.api.setParameter(['Generic Settings', 'Acquisition Settings', 'Number of Traces', 1500])
self.api.saveProject("projects/tut_randkey_randplain.cwp")
self.api.captureM()
self.api.saveProject()
# Capture a set of traces with fixed key and save the project
self.api.newProject()
self.api.saveProject("projects/tut_fixedkey_randplain.cwp")
self.api.setParameter(['Generic Settings', 'Basic', 'Key', 'Fixed'])
self.api.setParameter(['Generic Settings', 'Acquisition Settings', 'Number of Traces', 20])
self.api.captureM()
self.api.saveProject()
def run(self):
# Deletes previous saved data
if os.path.isfile("projects/tut_descpa.cwp"):
os.remove("projects/tut_descpa.cwp")
shutil.rmtree("projects/tut_descpa_data", ignore_errors=True)
# Setup the capture hardware
self.api.setParameter(
['Generic Settings', 'Scope Module', 'ChipWhisperer/OpenADC'])
self.api.setParameter(
['Generic Settings', 'Target Module', 'Simple Serial'])
self.api.setParameter(
['Generic Settings', 'Trace Format', 'ChipWhisperer/Native'])
self.api.setParameter(
['Simple Serial', 'Connection', 'NewAE USB (CWLite/CW1200)'])
self.api.setParameter([
'ChipWhisperer/OpenADC', 'Connection', 'NewAE USB (CWLite/CW1200)'
])
# Conect both: scope and target
self.api.connect()
# Flash the firmware
xmega = XMEGAProgrammer()
xmega.setUSBInterface(self.api.getScope().scopetype.dev.xmega)
xmega._logging = None
xmega.find()
xmega.erase()
xmega.program(r"simpleserial-des-xmega.hex",
memtype="flash",
verify=True)
xmega.close()
# Setup the capture parameters
lstexample = [
[
'CW Extra Settings', 'Trigger Pins',
'Target IO4 (Trigger Line)', True
],
[
'CW Extra Settings', 'Target IOn Pins', 'Target IO1',
'Serial RXD'
],
[
'CW Extra Settings', 'Target IOn Pins', 'Target IO2',
'Serial TXD'
],
[
'OpenADC', 'Clock Setup', 'CLKGEN Settings',
'Desired Frequency', 7370000.0
],
['CW Extra Settings', 'Target HS IO-Out', 'CLKGEN'],
[
'OpenADC', 'Clock Setup', 'ADC Clock', 'Source',
'CLKGEN x4 via DCM'
],
['OpenADC', 'Trigger Setup', 'Total Samples', 3500],
['OpenADC', 'Trigger Setup', 'Offset', 15500],
['OpenADC', 'Gain Setting', 'Setting', 45],
['OpenADC', 'Trigger Setup', 'Mode', 'rising edge'],
#Final step: make DCMs relock in case they are lost
['OpenADC', 'Clock Setup', 'ADC Clock', 'Reset ADC DCM', None],
]
for cmd in lstexample:
self.api.setParameter(cmd)
# Capture a set of traces with fixed key and save the project
self.api.newProject()
self.api.saveProject("projects/tut_descpa.cwp")
self.api.setParameter(['Simple Serial', 'Key Length (Bytes)', 8])
self.api.setParameter(['Simple Serial', 'Input Length (Bytes)', 8])
self.api.setParameter(['Simple Serial', 'Output Length (Bytes)', 8])
self.api.setParameter(['Generic Settings', 'Basic', 'Key', 'Fixed'])
self.api.setParameter([
'Generic Settings', 'Basic', 'Fixed Encryption Key',
u'2B 7E 15 16 28 AE D2 A6'
])
self.api.setParameter([
'Generic Settings', 'Acquisition Settings', 'Number of Traces', 100
])
time.sleep(1)
self.api.captureM()
self.api.saveProject()
class XMEGAProgrammerDialog(QtFixes.QDialog):
def __init__(self):
super(XMEGAProgrammerDialog, self).__init__(CWMainGUI.getInstance())
# self.setWindowFlags(self.windowFlags() | Qt.WindowStaysOnTopHint)
self.xmega = XMEGAProgrammer()
self.setWindowTitle("ChipWhisperer-Lite XMEGA Programmer")
layout = QVBoxLayout()
layoutFW = QHBoxLayout()
self.flashLocation = QtFixes.QLineEdit()
flashFileButton = QPushButton("Find")
flashFileButton.clicked.connect(self.findFlash)
layoutFW.addWidget(QLabel("FLASH File"))
layoutFW.addWidget(self.flashLocation)
layoutFW.addWidget(flashFileButton)
layout.addLayout(layoutFW)
self.flashLocation.setText(QSettings().value("xmega-flash-location"))
# Add buttons
readSigBut = QPushButton("Check Signature")
readSigBut.clicked.connect(self.readSignature)
verifyFlashBut = QPushButton("Verify FLASH")
verifyFlashBut.clicked.connect(self.verifyFlash)
verifyFlashBut.setEnabled(False)
progFlashBut = QPushButton("Erase/Program/Verify FLASH")
progFlashBut.clicked.connect(self.writeFlash)
layoutBut = QHBoxLayout()
layoutBut.addWidget(readSigBut)
layoutBut.addWidget(verifyFlashBut)
layoutBut.addWidget(progFlashBut)
layout.addLayout(layoutBut)
# Add status stuff
self.statusLine = QPlainTextEdit()
self.statusLine.setReadOnly(True)
# self.statusLine.setFixedHeight(QFontMetrics(self.statusLine.font()).lineSpacing() * 5 + 10)
self.xmega.newTextLog.connect(self.append)
layout.addWidget(self.statusLine)
# Set dialog layout
self.setLayout(layout)
def append(self, text):
self.statusLine.appendPlainText(text)
def findFlash(self):
fname, _ = QFileDialog.getOpenFileName(
self, 'Find FLASH File',
QSettings().value("xmega-flash-location"), '*.hex')
if fname:
self.flashLocation.setText(fname)
QSettings().setValue("xmega-flash-location", fname)
def readSignature(self, close=True):
self.xmega.find()
if close:
self.xmega.close()
def verifyFlash(self):
pass
def writeFlash(self, erase=True, verify=True):
self.xmega.autoProgram(self.flashLocation.text(), erase, verify,
self.statusLine.appendPlainText,
QCoreApplication.processEvents)
def setUSBInterface(self, iface):
self.xmega.setUSBInterface(iface)
print("Erase target...")
# program the XMEGA with the built hex file
# programmer = AVRProgrammer()
programmer = XMEGAProgrammer()
programmer.scope = scope
programmer._logging = None
programmer.find()
programmer.erase()
print("Programming...")
# programmer.program("~/software/chipwhisperer/hardware/victims/firmware/glitch-simple/glitchsimple-CW304.hex", memtype="flash")
programmer.program("glitchsimple.hex", memtype="flash", verify=False)
programmer.close()
scope.glitch.trigger_src = 'ext_single'
traces = []
outputs = []
widths = []
offsets = []
Range = namedtuple('Range', ['min', 'max', 'step'])
gc = support.GlitchCore()
gc.setRepeat(1)
gc.setWidth(38.5)
gc.setOffsetRange(29.0, 32.0, 0.5)
gc.setExtOffsetRange(15, 30, 1)
def test_TutorialB5(self):
self.aes_firmware_dir = os.path.join(FIRMWARE_DIR, "simpleserial-aes")
# Build firmware
logging.info('Building firmware from make file')
call = ["make", "--directory", self.aes_firmware_dir, "PLATFORM=CW303"]
logging.info(call)
exit_code = subprocess.check_call(call)
if exit_code == 0:
logging.info('Finished building firmware')
else:
logging.error('Build Failed with exit code {}'.format(exit_code))
# create capture gui
self.auto_ui = test_tools.FakeUI()
self.auto_ui.create_capture()
capture_gui = self.auto_ui.capture.gui
# TODO use the created project (currently cause PyQtGraph error)
# connect scope and target
logging.info('Executing "connect_cwlite_simpleserial.py"')
connect_cwlite_simpleserial = os.path.join(
CAPTURE_SCRIPTS_DIR, "connect_cwlite_simpleserial.py")
capture_gui.execute(script_path=connect_cwlite_simpleserial)
self.auto_ui.updateUI()
logging.info('Finished executing "connect_cwlite_simpleserial.py"')
# program the target with the built firmware
programmer = XMEGAProgrammer()
programmer.scope = capture_gui.scope
programmer._logging = None
programmer.find()
programmer.erase()
aes_hex = os.path.join(self.aes_firmware_dir,
r"simpleserial-aes-CW303.hex")
programmer.program(aes_hex, memtype="flash", verify=True)
programmer.close()
# Execute the setup script for simple serial aes
logging.info('Executing "setup_cwlite_xmega_aes.py"')
setup_cwlite_xmega_aes = os.path.join(CAPTURE_SCRIPTS_DIR,
"setup_cwlite_xmega_aes.py")
capture_gui.execute(script_path=setup_cwlite_xmega_aes)
self.auto_ui.updateUI()
logging.info('Finished executing "setup_cwlite_xmega.py"')
# Create a basic key text pattern
logging.info('Creating key text pattern')
ktp = AcqKeyTextPattern_Basic()
logging.info('Finished creating key text pattern')
# Capture traces
logging.info('Capturing traces')
capture_gui.execute(string='self.api.setNumTraces(60)')
capture_gui.doCapture(capture_gui.captureM)
self.auto_ui.updateUI()
logging.info('Finished capturing traces')
# Close the capture gui and open the analyzer gui
logging.info('Closing capture and opening analyzer')
self.auto_ui.close_capture()
self.auto_ui.create_analyzer()
analyzer_gui = self.auto_ui.analyzer.gui
logging.info('Finished closing capture and opening analyzer')
# TODO Open the project in the analyzer gui
#logging.info('Opening project')
#analyzer_gui.project = self.project
#logging.info('Finished opening project')
# Perform the attack
attack_cpa_script = os.path.join(ANALYZER_SCRIPTS_DIR, "attack_cpa.py")
logging.info('Executing attack script {}'.format(attack_cpa_script))
analyzer_gui.execute(script_path=attack_cpa_script)
self.auto_ui.updateUI()
logging.info('Finished executing attack script')
# check if the key is the expected key
result_subkeys = self.auto_ui.analyzer.gui.results_table.sub_key_row(1)
result_key = u' '.join(result_subkeys)
actual_key = ktp.initkey
logging.info('Actual Key: {}'.format(actual_key))
logging.info('Result Key: {}'.format(result_key))
if result_key == actual_key:
logging.info('Sucess, keys match')
else:
logging.error('Keys do not match')
self.assertEqual(result_key, actual_key)
# close the analayzer
self.auto_ui.close_analyzer()
def run(self):
# Delete previous project files
if os.path.isfile("projects/glitchtest.cwp"): os.remove("projects/glitchtest.cwp")
shutil.rmtree("projects/glitchtest_data", ignore_errors=True)
# Save current open project (default) to a new place
self.api.saveProject("projects/glitchtest.cwp")
print "Software Setup - 1. Connect to the ChipWhisperer device:"
self.api.setParameter(['Generic Settings', 'Scope Module', 'ChipWhisperer/OpenADC'])
self.api.setParameter(['Generic Settings', 'Target Module', 'Simple Serial'])
self.api.setParameter(['Generic Settings', 'Trace Format', 'None'])
self.api.setParameter(['Simple Serial', 'Connection', 'NewAE USB (CWLite/CW1200)'])
self.api.setParameter(['ChipWhisperer/OpenADC', 'Connection', 'NewAE USB (CWLite/CW1200)'])
# Connect to both: scope and target
self.api.connect()
print "Software Setup - 2. Setup the CLKGEN Module to Generate a 7.37 MHz clock and route it through the Glitch Generator"
lstexample = [
['OpenADC', 'Clock Setup', 'Freq Counter Src', 'CLKGEN Output'],
['OpenADC', 'Clock Setup', 'CLKGEN Settings', 'Desired Frequency', 7370000.0],
['OpenADC', 'Clock Setup', 'ADC Clock', 'Reset ADC DCM', None],
['Glitch Module', 'Clock Source', 'CLKGEN'],
['CW Extra Settings', 'Target HS IO-Out', 'Glitch Module'],
]
for cmd in lstexample: self.api.setParameter(cmd)
print "Software Setup - 3. Connect the Serial Port"
lstexample = [
['CW Extra Settings', 'Target IOn Pins', 'Target IO1', 'Serial RXD'],
['CW Extra Settings', 'Target IOn Pins', 'Target IO2', 'Serial TXD']
]
for cmd in lstexample: self.api.setParameter(cmd)
print "Software Setup - 3.4. Flashing test firmware"
xmega = XMEGAProgrammer()
xmega.setUSBInterface(self.api.getScope().scopetype.dev.xmega)
xmega._logging = None
xmega.find()
xmega.erase()
xmega.program(r"glitchsimple.hex", memtype="flash", verify=True)
xmega.close()
print "Manual Glitch Trigger"
lstexample = [
['Glitch Module', 'Glitch Width (as % of period)', 10],
['Glitch Module', 'Glitch Offset (as % of period)', 26.6],
['Glitch Module', 'Repeat', 105],
['Glitch Module', 'Glitch Trigger', 'Manual'],
['Glitch Module', 'Manual Trigger / Single-Shot Arm', None], # Push the button
]
for cmd in lstexample: self.api.setParameter(cmd)
print "Automatically Resetting Target"
lstexample = [
['Generic Settings', 'Auxiliary Module', 'Reset AVR/XMEGA via CW-Lite'],
['Aux Settings', 'Reset AVR/XMEGA via CW-Lite', 'Interface', 'xmega (PDI)'],
['Aux Settings', 'Reset AVR/XMEGA via CW-Lite', 'Test Reset', None], # Push the button
['Simple Serial', 'Load Key Command', u''],
['Simple Serial', 'Go Command', u''],
['Simple Serial', 'Output Format', u''],
]
for cmd in lstexample: self.api.setParameter(cmd)
self.api.capture1()
self.api.capture1()
self.api.capture1()
print "Automatically Triggering Glitch - Enable the power analysis capture"
lstexample = [
['OpenADC', 'Clock Setup', 'ADC Clock', 'Source', 'CLKGEN x4 via DCM'],
['OpenADC', 'Clock Setup', 'ADC Clock', 'Reset ADC DCM', None], # Push the button
['OpenADC', 'Trigger Setup', 'Mode', 'rising edge'],
['OpenADC', 'Trigger Setup', 'Total Samples', 1000],
['OpenADC', 'Gain Setting', 'Setting', 40],
]
for cmd in lstexample: self.api.setParameter(cmd)
self.api.capture1()
self.api.capture1()
self.api.capture1()
print "Automatically Triggering Glitch - Enable the trigger of the glitch to occur based on this external trigger pin"
self.api.setParameter(['Glitch Module', 'Glitch Trigger', 'Ext Trigger:Single-Shot'])
self.api.capture1()
self.api.capture1()
self.api.capture1()
print "Using the Glitch Explorer"
self.api.setParameter(['Simple Serial', 'Output Format', u'$GLITCH$'])
self.api.capture1()
self.api.capture1()
self.api.capture1()
lstexample = [
['Glitch Explorer', 'Normal Response', u"s == '\\x00hello\\nA'"],
['Glitch Explorer', 'Successful Response', u"s.endswith('1234')"],
]
for cmd in lstexample: self.api.setParameter(cmd)
self.api.capture1()
self.api.capture1()
self.api.capture1()
print "Using the Glitch Explorer - Tune the glitch offset to attempt to get a successful clock glitch"
self.api.setParameter(['Glitch Explorer', 'Plot Widget', None]) # Push the button
lstexample = [
['Glitch Explorer', 'Tuning Parameters', 1],
['Glitch Explorer', 'Tuning Parameter 0', 'Name', u'Offset'],
['Glitch Explorer', 'Tuning Parameter 0', 'Parameter Path', u"['Glitch Module', 'Glitch Offset (as % of period)']"],
['Glitch Explorer', 'Tuning Parameter 0', 'Data Format', 'Float'],
['Glitch Explorer', 'Tuning Parameter 0', 'Range', (-30, 30)],
['Glitch Explorer', 'Tuning Parameter 0', 'Value', -30.0],
['Glitch Explorer', 'Tuning Parameter 0', 'Step', 0.5],
['Glitch Explorer', 'Tuning Parameter 0', 'Repeat', 1],
['Glitch Module', 'Repeat', 10],
['Glitch Module', 'Glitch Width (as % of period)', 8.0],
['Generic Settings', 'Acquisition Settings', 'Number of Traces', 121]
]
for cmd in lstexample: self.api.setParameter(cmd)
self.api.captureM()
print "Using the Glitch Explorer - Tune the Glitch Width"
lstexample = [
['Glitch Explorer', 'Tuning Parameters', 2],
['Glitch Explorer', 'Tuning Parameter 1', 'Name', u'Width'],
['Glitch Explorer', 'Tuning Parameter 1', 'Parameter Path', u"['Glitch Module', 'Glitch Width (as % of period)']"],
['Glitch Explorer', 'Tuning Parameter 1', 'Data Format', 'Float'],
['Glitch Explorer', 'Tuning Parameter 1', 'Range', (4, 11)],
['Glitch Explorer', 'Tuning Parameter 1', 'Value', 4],
['Glitch Explorer', 'Tuning Parameter 1', 'Step', 0.5],
['Glitch Explorer', 'Tuning Parameter 1', 'Repeat', 1],
['Glitch Explorer', 'Tuning Parameter 0', 'Range', (-8, 3)],
['Glitch Explorer', 'Tuning Parameter 0', 'Value', -8],
['Glitch Module', 'Repeat', 1],
['Generic Settings', 'Acquisition Settings', 'Number of Traces', 345],
]
for cmd in lstexample: self.api.setParameter(cmd)
self.api.captureM()
print "Using the Glitch Explorer - Fine-tune those values"
self.api.setParameter(['Glitch Module', 'Glitch Offset (as % of period)',-3.5])
self.api.setParameter(['Glitch Module', 'Glitch Width (as % of period)',7.5])
self.api.capture1()
self.api.capture1()
self.api.capture1()
self.api.setParameter(['Glitch Module', 'Glitch Offset (fine adjust)', 44])
self.api.capture1()
self.api.capture1()
self.api.capture1()
class XMEGAProgrammerDialog(QtFixes.QDialog):
def __init__(self):
super(XMEGAProgrammerDialog, self).__init__(CWMainGUI.getInstance())
# self.setWindowFlags(self.windowFlags() | Qt.WindowStaysOnTopHint)
self.xmega = XMEGAProgrammer()
self.setWindowTitle("ChipWhisperer-Lite XMEGA Programmer")
layout = QVBoxLayout()
layoutFW = QHBoxLayout()
self.flashLocation = QtFixes.QLineEdit()
flashFileButton = QPushButton("Find")
flashFileButton.clicked.connect(self.findFlash)
layoutFW.addWidget(QLabel("FLASH File"))
layoutFW.addWidget(self.flashLocation)
layoutFW.addWidget(flashFileButton)
layout.addLayout(layoutFW)
self.flashLocation.setText(QSettings().value("xmega-flash-location"))
# Add buttons
readSigBut = QPushButton("Check Signature")
readSigBut.clicked.connect(self.readSignature)
verifyFlashBut = QPushButton("Verify FLASH")
verifyFlashBut.clicked.connect(self.verifyFlash)
verifyFlashBut.setEnabled(False)
progFlashBut = QPushButton("Erase/Program/Verify FLASH")
progFlashBut.clicked.connect(self.writeFlash)
layoutBut = QHBoxLayout()
layoutBut.addWidget(readSigBut)
layoutBut.addWidget(verifyFlashBut)
layoutBut.addWidget(progFlashBut)
layout.addLayout(layoutBut)
# Add status stuff
self.statusLine = QPlainTextEdit()
self.statusLine.setReadOnly(True)
# self.statusLine.setFixedHeight(QFontMetrics(self.statusLine.font()).lineSpacing() * 5 + 10)
self.statusLine.append = self.statusLine.appendPlainText
layout.addWidget(self.statusLine)
self.xmega._logging = self.statusLine.append
# Set dialog layout
self.setLayout(layout)
def findFlash(self):
fname, _ = QFileDialog.getOpenFileName(self, 'Find FLASH File', QSettings().value("xmega-flash-location"), '*.hex')
if fname:
self.flashLocation.setText(fname)
QSettings().setValue("xmega-flash-location", fname)
def readSignature(self, close=True):
self.xmega.find()
if close:
self.xmega.close()
def verifyFlash(self):
pass
def writeFlash(self, erase=True, verify=True):
status = "FAILED"
fname = self.flashLocation.text()
self.statusLine.append("***Starting FLASH program process at %s***" % datetime.now().strftime('%H:%M:%S'))
if (os.path.isfile(fname)):
self.statusLine.append("File %s last changed on %s" % (fname, time.ctime(os.path.getmtime(fname))))
QCoreApplication.processEvents()
try:
self.statusLine.append("Entering Programming Mode")
QCoreApplication.processEvents()
self.readSignature(close=False)
if erase:
try:
self.statusLine.append("Erasing Chip")
QCoreApplication.processEvents()
self.xmega.erase()
except IOError:
self.statusLine.append("**chip-erase timeout, erasing application only**")
QCoreApplication.processEvents()
self.xmega.xmega.enablePDI(False)
self.xmega.xmega.enablePDI(True)
self.xmega.erase("app")
QCoreApplication.processEvents()
self.xmega.program(self.flashLocation.text(), memtype="flash", verify=verify)
QCoreApplication.processEvents()
self.statusLine.append("Exiting programming mode")
self.xmega.close()
QCoreApplication.processEvents()
status = "SUCCEEDED"
except IOError, e:
self.statusLine.append("FAILED: %s" % str(e))
try:
self.xmega.close()
except IOError:
pass
else:
def test_tutorial_B6(self):
scope = self.scope
target = self.target
programmer = XMEGAProgrammer()
programmer.scope = scope
programmer._logging = None
programmer.find()
programmer.erase()
aes_firmware_dir = os.path.join(FIRMWARE_DIR, 'simpleserial-aes')
aes_hex = os.path.join(aes_firmware_dir, r"simpleserial-aes-CW303.hex")
programmer.program(aes_hex, memtype="flash", verify=True)
programmer.close()
# setup scope parameters
scope.gain.gain = 45
scope.adc.samples = 3000
scope.adc.offset = 1250
scope.adc.basic_mode = "rising_edge"
scope.clock.clkgen_freq = 7370000
scope.clock.adc_src = "clkgen_x4"
scope.trigger.triggers = "tio4"
scope.io.tio1 = "serial_rx"
scope.io.tio2 = "serial_tx"
scope.io.hs2 = "clkgen"
ktp = AcqKeyTextPattern_Basic(target=target)
traces = []
textin = []
N = 100 # Number of traces
print('Capturing traces...')
target.init()
for i in tqdm(range(N)):
key, text = ktp.newPair() # manual creation of a key, text pair can be substituted here
textin.append(text)
target.reinit()
target.setModeEncrypt() # only does something for targets that support it
target.loadEncryptionKey(key)
target.loadInput(text)
# run aux stuff that should run before the scope arms here
scope.arm()
# run aux stuff that should run after the scope arms here
target.go()
timeout=50
# wait for target to finish
while target.isDone() is False and timeout:
timeout -= 1
time.sleep(0.01)
try:
ret = scope.capture()
if ret:
logging.warning('Timeout happened during acquisition')
except IOError as e:
logging.error('IOError: %s' % str(e))
# run aux stuff that should happen after trace here
_ = target.readOutput() # for keep the v1.1 protocol working
traces.append(scope.getLastTrace())
knownkey = key
pt = np.asarray(textin)
traces = np.asarray(traces)
numtraces = np.shape(traces)[0]
numpoint = np.shape(traces)[1]
bestguess = [0] * 16
pge = [256] * 16
print("Attacking subkeys...")
for bnum in tqdm(range(0, 16)):
cpaoutput = [0] * 256
maxcpa = [0] * 256
for kguess in range(0, 256):
#print("Subkey %2d, hyp = %02x: " % (bnum, kguess), end='')
# Initialize arrays & variables to zero
sumnum = np.zeros(numpoint)
sumden1 = np.zeros(numpoint)
sumden2 = np.zeros(numpoint)
hyp = np.zeros(numtraces)
for tnum in range(0, numtraces):
hyp[tnum] = self.HW[self.intermediate(pt[tnum][bnum], kguess)]
# Mean of hypothesis
meanh = np.mean(hyp, dtype=np.float64)
# Mean of all points in trace
meant = np.mean(traces, axis=0, dtype=np.float64)
# For each trace, do the following
for tnum in range(0, numtraces):
hdiff = (hyp[tnum] - meanh)
tdiff = traces[tnum, :] - meant
sumnum = sumnum + (hdiff * tdiff)
sumden1 = sumden1 + hdiff * hdiff
sumden2 = sumden2 + tdiff * tdiff
cpaoutput[kguess] = sumnum / np.sqrt(sumden1 * sumden2)
maxcpa[kguess] = max(abs(cpaoutput[kguess]))
#print(maxcpa[kguess])
bestguess[bnum] = np.argmax(maxcpa)
cparefs = np.argsort(maxcpa)[::-1]
# Find PGE
pge[bnum] = list(cparefs).index(knownkey[bnum])
print("Best Key Guess: ", end="")
for b in bestguess: print("%02x " % b, end="")
print("")
print("PGE: ", end="")
for b in pge: print("%02d " % b, end="")
self.assertLess(sum(pge), 5)
def test_tutorial_A2(self):
# build the firmware
self.glitch_simple_firmware_dir = os.path.join(FIRMWARE_DIR, "glitch-simple")
# Build firmware
logging.info('Building firmware from make file')
call = ["make", "--directory", self.glitch_simple_firmware_dir, "PLATFORM=CW303"]
logging.info(call)
exit_code = subprocess.check_call(call)
if exit_code == 0:
logging.info('Finished building firmware')
else:
logging.error('Build Failed with exit code {}'.format(exit_code))
# connect the scope and target
scope = self.scope
target = self.target
# program the XMEGA with the built hex file
programmer = XMEGAProgrammer()
programmer.scope = scope
programmer._logging = None
programmer.find()
programmer.erase()
glitch_simple_hex = os.path.join(self.glitch_simple_firmware_dir, r"glitchsimple-CW303.hex")
programmer.program(glitch_simple_hex, memtype="flash", verify=True)
programmer.close()
# setup parameters needed for glitch the XMEGA
scope.glitch.clk_src = 'clkgen'
scope.gain.gain = 45
scope.adc.samples = 3000
scope.adc.offset = 0
scope.adc.basic_mode = "rising_edge"
scope.clock.clkgen_freq = 7370000
scope.clock.adc_src = "clkgen_x4"
scope.trigger.triggers = "tio4"
scope.io.tio1 = "serial_rx"
scope.io.tio2 = "serial_tx"
scope.io.hs2 = "glitch"
target.go_cmd = ""
target.key_cmd = ""
# set glitch parameters
# trigger glitches with external trigger
scope.glitch.trigger_src = 'ext_single'
scope.glitch.repeat = 105
traces = []
outputs = []
# named tuples to make it easier to change the scope of the test
Range = namedtuple('Range', ['min', 'max', 'step'])
width_range = Range(-10, 10, 1.7)
offset_range = Range(-10, 10, 1.7)
# glitch cycle
scope.glitch.width = width_range.min
success = False
target.init()
while scope.glitch.width < width_range.max and not success:
scope.glitch.offset = offset_range.min
while scope.glitch.offset < offset_range.max and not success:
# call before trace things here
# flush the garbage from the computer's target read buffer
target.ser.flush()
# target enters reset mode
scope.io.pdic = 'low'
# run aux stuff that should run before the scope arms here
scope.arm()
# run aux stuff that should run after the scope arms here
# target exits reset mode
scope.io.pdic = 'high'
timeout = 50
# wait for target to finish
while target.isDone() is False and timeout:
timeout -= 1
time.sleep(0.01)
try:
ret = scope.capture()
if ret:
logging.warning('Timeout happened during acquisition')
except IOError as e:
logging.error('IOError: %s' % str(e))
#textout = target.readOutput() # raises invalid literal for int base 16
# get the results
trace = scope.getLastTrace()
output = target.ser.read(target.output_len * 2, timeout=10)
traces.append(trace)
outputs.append(output)
if '1234' in repr(output):
success = True
# run aux stuff that should happen after trace here
scope.glitch.offset += offset_range.step
scope.glitch.width += width_range.step
self.assertTrue(success, 'There is no "1234" in the outputs, maybe glitch1() in c file is not active')
def run(self):
for cmd in [
['Generic Settings', 'Scope Module', 'ChipWhisperer/OpenADC'],
['Generic Settings', 'Target Module', 'Simple Serial'],
['Generic Settings', 'Trace Format', 'ChipWhisperer/Native'],
['Simple Serial', 'Connection', 'NewAE USB (CWLite/CW1200)'],
['ChipWhisperer/OpenADC', 'Connection', 'NewAE USB (CWLite/CW1200)'],
]:
self.api.setParameter(cmd)
self.api.connect()
# Flash the firmware
xmega = XMEGAProgrammer()
xmega.setUSBInterface(self.api.getScope().scopetype.dev.xmega)
xmega.find()
xmega.erase()
xmega.program(getFirmwarePath('usb-descriptor-simple'), memtype='flash', verify=True)
xmega.close()
# Capture parameters
for cmd in [
['Simple Serial', 'Load Key Command', u''],
['Simple Serial', 'Go Command', u'\n'],
['Simple Serial', 'Output Format', u'$GLITCH$8000'],
['Simple Serial', 'NewAE USB (CWLite/CW1200)', 'baud', 115200],
['CW Extra Settings', 'Trigger Pins', 'Target IO4 (Trigger Line)', True],
['CW Extra Settings', 'Target IOn Pins', 'Target IO1', 'Serial RXD'],
['CW Extra Settings', 'Target IOn Pins', 'Target IO2', 'Serial TXD'],
['CW Extra Settings', 'Target HS IO-Out', 'CLKGEN'],
['OpenADC', 'Clock Setup', 'CLKGEN Settings', 'Desired Frequency', 12e6],
['OpenADC', 'Clock Setup', 'ADC Clock', 'Source', 'CLKGEN x4 via DCM'],
['OpenADC', 'Trigger Setup', 'Total Samples', 24400],
['OpenADC', 'Trigger Setup', 'Pre-Trigger Samples', 0],
['OpenADC', 'Trigger Setup', 'Offset', 14100],
['OpenADC', 'Gain Setting', 'Setting', 38],
['OpenADC', 'Trigger Setup', 'Mode', 'rising edge'],
['OpenADC', 'Clock Setup', 'ADC Clock', 'Reset ADC DCM', None],
['Generic Settings', 'Acquisition Settings', 'Number of Traces', 500],
['CW Extra Settings', 'HS-Glitch Out Enable (Low Power)', True],
['CW Extra Settings', 'HS-Glitch Out Enable (High Power)', True],
['Glitch Module', 'Clock Source', 'CLKGEN'],
['Glitch Module', 'Single-Shot Arm', 'Before Scope Arm'],
['Glitch Module', 'Glitch Trigger', 'Ext Trigger:Single-Shot'],
['Glitch Module', 'Output Mode', 'Glitch Only'],
['Glitch Module', 'Glitch Width (as % of period)', 44.4],
['Glitch Module', 'Glitch Offset (as % of period)', 5.3],
['Glitch Module', 'Repeat', 2],
['Glitch Module', 'Ext Trigger Offset', 7218],
# Fixme: these are specific to the target device I'm experimenting on
['Glitch Explorer', 'Normal Response', u's.find("rcode 5 total 34") >= 0'],
['Glitch Explorer', 'Successful Response', u"(lambda n: n.isdigit() and int(n))((s+' x').split('total ')[-1].split()[0]) > 34"],
]:
self.api.setParameter(cmd)
self.api.capture1()
self.api.capture1()
class XMEGAProgrammerDialog(QtFixes.QDialog):
def __init__(self):
super(XMEGAProgrammerDialog, self).__init__(CWMainGUI.getInstance())
# self.setWindowFlags(self.windowFlags() | Qt.WindowStaysOnTopHint)
self.xmega = XMEGAProgrammer()
self.setWindowTitle("ChipWhisperer-Lite XMEGA Programmer")
layout = QVBoxLayout()
layoutFW = QHBoxLayout()
self.flashLocation = QtFixes.QLineEdit()
flashFileButton = QPushButton("Find")
flashFileButton.clicked.connect(self.findFlash)
layoutFW.addWidget(QLabel("FLASH File"))
layoutFW.addWidget(self.flashLocation)
layoutFW.addWidget(flashFileButton)
layout.addLayout(layoutFW)
self.flashLocation.setText(QSettings().value("xmega-flash-location"))
# Add buttons
readSigBut = QPushButton("Check Signature")
readSigBut.clicked.connect(self.readSignature)
verifyFlashBut = QPushButton("Verify FLASH")
verifyFlashBut.clicked.connect(self.verifyFlash)
verifyFlashBut.setEnabled(False)
progFlashBut = QPushButton("Erase/Program/Verify FLASH")
progFlashBut.clicked.connect(self.writeFlash)
layoutBut = QHBoxLayout()
layoutBut.addWidget(readSigBut)
layoutBut.addWidget(verifyFlashBut)
layoutBut.addWidget(progFlashBut)
layout.addLayout(layoutBut)
# Add status stuff
self.statusLine = QPlainTextEdit()
self.statusLine.setReadOnly(True)
# self.statusLine.setFixedHeight(QFontMetrics(self.statusLine.font()).lineSpacing() * 5 + 10)
self.xmega.newTextLog.connect(self.append)
layout.addWidget(self.statusLine)
# Set dialog layout
self.setLayout(layout)
def append(self, text):
self.statusLine.appendPlainText(text)
def findFlash(self):
fname, _ = QFileDialog.getOpenFileName(
self, 'Find FLASH File',
QSettings().value("xmega-flash-location"), '*.hex')
if fname:
self.flashLocation.setText(fname)
QSettings().setValue("xmega-flash-location", fname)
def readSignature(self, close=True):
self.xmega.find()
if close:
self.xmega.close()
def verifyFlash(self):
pass
def writeFlash(self, erase=True, verify=True):
status = "FAILED"
fname = self.flashLocation.text()
self.statusLine.appendPlainText(
"***Starting FLASH program process at %s***" %
datetime.now().strftime('%H:%M:%S'))
if (os.path.isfile(fname)):
self.statusLine.appendPlainText(
"File %s last changed on %s" %
(fname, time.ctime(os.path.getmtime(fname))))
QCoreApplication.processEvents()
try:
self.statusLine.appendPlainText("Entering Programming Mode")
QCoreApplication.processEvents()
self.readSignature(close=False)
if erase:
try:
self.xmega.erase()
except IOError:
self.statusLine.appendPlainText(
"**chip-erase timeout, erasing application only**")
QCoreApplication.processEvents()
self.xmega.xmega.enablePDI(False)
self.xmega.xmega.enablePDI(True)
self.xmega.erase("app")
QCoreApplication.processEvents()
self.xmega.program(self.flashLocation.text(),
memtype="flash",
verify=verify)
QCoreApplication.processEvents()
self.statusLine.appendPlainText("Exiting programming mode")
self.xmega.close()
QCoreApplication.processEvents()
status = "SUCCEEDED"
except IOError, e:
self.statusLine.appendPlainText("FAILED: %s" % str(e))
try:
self.xmega.close()
except IOError:
pass
else:
