def redac(self):
self.dac = DAC(Pin('X5'),buffering=self.buffer_dac)
self.bmv = memoryview(self.buf)[:len(self)]
self.dac_tim = Timer(6, freq=int(self.hres*1000000/self.line_time))
self.dac.write_timed(self.bmv,self.dac_tim,mode=DAC.CIRCULAR)
self.frame_tim = Timer(5, prescaler=self.dac_tim.prescaler(),period=self.dac_tim.period()*len(self))
self.frame_tim.counter(self.phase)
def luminance(self, mode): """Sample luminance (in lux), using specified sensor mode.""" # continuous modes if mode & 0x10 and mode != self.mode: self.set_mode(mode) # one shot modes if mode & 0x20: self.set_mode(mode) # earlier measurements return previous reading if mode in (0x13, 0x23): time.sleep_ms(24) else: time.sleep_ms(180) data = self.bus.recv(16,addr=self.addr) if mode in (0x11, 0x21): factor = 2.0 else: factor = 1.0 print ((data[0]<<8 | data[1]) / (1.2 * factor)) buf = bytearray(16) for i in range(len(data)): buf[i]=data[i] print(buf) # output the sine-wave at 400Hz dac = DAC(1) dac.write_timed(buf, 400 * len(buf), mode=DAC.CIRCULAR)
def __init__(self, amps=[], freqs=[], bufs=[], ch=1):
# amps: 幅值序列
# bufs: 对应幅值的正弦序列
self.timer = Timer(6)
self.dac = DAC(ch, bits=12)
self.amps = amps
self.bufs = bufs
self.freqs = freqs
self.indx = range(len(amps))
self.newtask = False
def __init__(self,
bufs,
freqs,
DAC_ch,
sync,
BoardCtrl,
repeat=50,
timer_num=6):
'''
bufs: list, DAC output array
typ: list, the same length with bufs, 'tiny','big','cut' to describe which type of the buf
freqs: list, tested frequences
ch: DAC output channel, 1: 'X5' 2: 'X6'
sync: object for output synchronus signal to record client
resistset: object for adjusting resist according to the magnet strength
timer: internal timer, default 6
'''
self.bufs = bufs
self.freqs = freqs
if DAC_ch == 'X5':
self.dac = DAC(1, bits=12)
elif DAC_ch == 'X6':
self.dac = DAC(2, bits=12)
else:
raise ValueError('DAC pin should be X5 or X6')
self.sync = sync
self.boardctrl = BoardCtrl
self.timer = Timer(timer_num)
self.buf_indx = 0
self.fre_indx = 0
self.fre_len = len(self.freqs)
self.buf_len = len(self.bufs)
self.repeat = repeat
self.rcount = 0
self.end_flg = False
self.new_block = False
self.stimulus_level = 0
def __init__(self, dac=DAC(1), timerno=4):
global lwr
lwr = self
self._f = None
self._rate = 0
self._amount = 0
self._freq = 4 # in Hertz
self._dac = dac
self._have = [False, False]
self._buf = [None, None]
self._doneindex = 0
self._speed = 100
self._timer = pyb.Timer(timerno, freq=self._freq)
self._running = False
self._fill()
def __init__(self):
self.p_SICL = Pin(config.SICL, Pin.OUT_PP)
self.p_SIBL = Pin(config.SIBL, Pin.OUT_PP)
self.p_CK = Pin(config.CK, Pin.OUT_PP)
self.p_LAT = Pin(config.LAT, Pin.OUT_PP)
self.p_CH = Pin(config.CH, Pin.OUT_PP)
self.p_NCHG = Pin(config.NCHG, Pin.OUT_PP)
self.p_LAT.value(0)
self.p_NCHG.value(0)
self.dac = DAC(1)
self.dac.write(127)
waveform = config.WAVEFORM
factor = max(waveform)
for i in range(len(waveform)):
waveform[i] = int(255*(waveform[i]/factor))
self.waveform = array('i', waveform)
def __init__(self, freqs=[], bufs=[], ch=1, **kwargs):
# freqs:待测试的频率
# bufs: 对应幅值的正弦序列等消息，每个元素包含(amp,buf,port)
# 其中port是指，使用可变电阻时对应控制的端口
# ch:测试信号输出端口选择
# kwargs: r_port,电阻选择的端口列表
self.timer = Timer(6)
self.dac = DAC(ch, bits=12)
self.freqs = freqs
self.bufs = bufs
self.r_adapt = False
if len(kwargs) > 0:
if 'r_port' in kwargs: #使用电阻自适应调整
self.r_adapt = True
(pyb.Pin(pin, pyb.Pin.OUT_PP) for pin in kwargs['r_port'])
self.freqs = freqs
self.indx = range(len(amps))
self.newtask = False
def pins_test():
i2c = I2C(1, I2C.MASTER)
spi = SPI(2, SPI.MASTER)
uart = UART(3, 9600)
servo = Servo(1)
adc = ADC(Pin.board.X3)
dac = DAC(1)
pin = Pin('X4', mode=Pin.AF_PP, af=Pin.AF3_TIM9)
pin = Pin('Y1', mode=Pin.AF_OD, af=3)
pin = Pin('Y2', mode=Pin.OUT_PP)
pin = Pin('Y3', mode=Pin.OUT_OD, pull=Pin.PULL_UP)
pin.high()
pin = Pin('Y4', mode=Pin.OUT_OD, pull=Pin.PULL_DOWN)
pin.high()
pin = Pin('X18', mode=Pin.IN, pull=Pin.PULL_NONE)
pin = Pin('X19', mode=Pin.IN, pull=Pin.PULL_UP)
pin = Pin('X20', mode=Pin.IN, pull=Pin.PULL_DOWN)
print('===== output of pins() =====')
pins()
print('===== output of af() =====')
af()
sensor.set_auto_gain(False) # must be turned off for color tracking
sensor.set_auto_whitebal(False) # must be turned off for color tracking
clock = time.clock()
# Only blobs that with more pixels than "pixel_threshold" and more area than "area_threshold" are
# returned by "find_blobs" below. Change "pixels_threshold" and "area_threshold" if you change the
# camera resolution. "merge=True" must be set to merge overlapping color blobs for color codes.
while(True):
clock.tick()
img = sensor.snapshot()
for blob in img.find_blobs([thresholds[1]], pixels_threshold=100, area_threshold=100, merge=True):
img.draw_rectangle(blob.rect())
img.draw_cross(blob.cx(), blob.cy())
img.draw_string(blob.x() + 2, blob.y() + 2, "verde")
dac = DAC('P6')#Select pin whit DAC or ADC
dac.write(255) # output between 0 and 255
for blob in img.find_blobs([thresholds[0]], pixels_threshold=100, area_threshold=100, merge=True):
img.draw_rectangle(blob.rect())
img.draw_cross(blob.cx(), blob.cy())
img.draw_string(blob.x() + 2, blob.y() + 2, "rojo")
dac = DAC('P6')#Select pin whit DAC or ADC
dac.write(100) # output between 0 and 255
for blob in img.find_blobs([thresholds[2]], pixels_threshold=100, area_threshold=100, merge=True):
img.draw_rectangle(blob.rect())
img.draw_cross(blob.cx(), blob.cy())
img.draw_string(blob.x() + 2, blob.y() + 2, "amarillo")
dac = DAC('P6')#Select pin whit DAC or ADC
dac.write(50) # output between 0 and 255
print(clock.fps())
def __init__(self, buf=array('H', [100]), ch=1):
self.timer = Timer(6)
self.dac = DAC(ch, bits=12)
self.buf = buf
self.dac_on = 0
from pyb import DAC dac = DAC(1) # create DAC 1 on pin X5 dac.write(128) # write a value to the DAC (makes X5 1.65V) dac = DAC(1, bits=12) # use 12 bit resolution dac.write(4095) # output maximum value, 3.3V
版本：v1.0
日期：2019.9
作者：01Studio
说明：通过KEY按键让DAC输出不同频率的方波来驱动蜂鸣器。
'''
#导入相关模块
from pyb import DAC,ExtInt
from machine import Pin,I2C
from ssd1306x import SSD1306_I2C
#初始化相关模块
i2c = I2C(sda=Pin("P0"), scl=Pin("P2"),freq=80000)
oled = SSD1306_I2C(128, 64, i2c, addr=0x3c)
dac = DAC(Pin("P6")) #定义DAC对象名字为dac，输出引脚为P6
#定义4组频率值：1Hz、200Hz、1000Hz、5000Hz
freq=[1,200,1000,5000]
# 定义8位精度下方波的值。0、255分别对应输出0V、3.3V。需要定义成字节数组。
buf = bytearray(2)
buf[0]=0
buf[1]=255
key_node = 0 #按键标志位
i = 0 #用于选择频率数组
##############################################
# 按键和其回调函数
##############################################
state = 'front'
control_dict = {
"__START__": 1000,
"__SPEED15__": 1001,
"__SPEED20__": 1002,
"__SPEED25__": 1003,
"__STATUSUPDATE__": 1004,
"__TURNRIGHT__": 2500,
"__TURNLEFT__": 1500,
"__BREAK__": 4000,
"__SET__": 6000,
"__RESETPIBOARD__": 5000
} #Here __RESETPIBOARD__ is to stop the vehicle (ie., to set DAC=0)
# ------- Complex--------#
tim = pyb.Timer(10, freq=10) #timer
dacA, dacB = DAC(1, bits=12), DAC(2, bits=12) #DAC Initialization
pidL = PID.PID(45, 0, 90) #PID
pidR = PID.PID(40, 0, 80)
# -------- PINS---------#
#Y1,Y2,Y3 are for ExtInt
motor_relay_L = Pin(
'Y4',
Pin.OUT_PP) #relay for brakes; connected in a normally open connection
motor_relay_R = Pin('Y5', Pin.OUT_PP)
motor1_switch = Pin(
'Y6', Pin.OUT_PP) #Relay for DAC; connected in a normally open connection
motor2_switch = Pin('Y7', Pin.OUT_PP)
motor_L_brake = Pin('X9', Pin.OUT_PP) #regenerative braking
motor_R_brake = Pin('X10', Pin.OUT_PP)
#############################################################################################################
from pyb import DAC dac = DAC(1) # DAC 1 sur la broche A0 (Feather) ou X5 (Pyboard) dac.write(128) # Ecriture d'une valeur sur 8 bit dac = DAC(1, bits=12) # DAC 1 en 12 bit dac.write(4095) # Ecriture de la valeur maximale
from pyb import DAC
from pyb import LED
import math
# Turn on the light so you know something is happening
led = LED(4)
led.on()
# Write out a sinusoidal curve to channel X5, which is wired via a
# female-female jumper to X2
# --
# create a buffer containing a sine-wave, using half-word samples
buf = array(
'H', 2048 + int(2047 * math.sin(2 * math.pi * i / 128))
for i in range(128))
dac = DAC(1, bits=12) # Wired to X5
dac.write_timed(buf, 400 * len(buf), mode=DAC.CIRCULAR)
# Instatiate the USB serial object
u = USB_VCP()
u.write('Hello world!!')
# Enter into an infinite loop
while True:
# Get a line from the serial connection
line = u.readline()
# If there is nothing, line will be None
if not line is None and line:
from pyb import DAC sa1 = DAC(1) sa1.triangle(400*2048)
tim = Timer(2, freq=1000)
ch = Timer.channel(1, Timer.PWM, pin=p)
ch.pulse_width_percent(50)
'''
1.9 ADC
'''
from pyb import Pin, ADC
adc = ADC(Pin('X19'))
adc.read() # read value, 0 - 4095
'''
1.10 DAC
'''
from pyb import Pin, DAC
dac = DAC(Pin('X5'))
dac.write(120) # output between 0 and 255
'''
1.11 UART
'''
from pyb import UART
uart1 = UART(1, 9600)
uart1.write('hello')
uart1.read(5) # read up to 5 bytes
'''
1.12 SPI Bus
'''
from pyb import SPI
spi1 = SPI(1, SPI.MASTER, baudrate=200000, polarity=1, phase=0)
# DAC Timed Write Example
#
# This example shows how to use the DAC pin output onboard your OpenMV Cam.
import math
from pyb import DAC
# create a buffer containing a sine-wave
buf = bytearray(100)
for i in range(len(buf)):
buf[i] = 128 + int(127 * math.sin(2 * math.pi * i / len(buf)))
# output the sine-wave at 400Hz
dac = DAC("P6")
dac.write_timed(buf, 400 * len(buf), mode=DAC.CIRCULAR)
try:
from pyb import DAC
from pyb import LED
from pyb import Pin
from pyb import USB_VCP
sensitivity, maxn, minn = .5, 255, 0
com = USB_VCP()
light = DAC(2)
y1, y2, y3 = Pin('Y1', Pin.IN), Pin('Y2', Pin.IN), Pin('Y3', Pin.IN)
intensity, oldStr = maxn, str(y1.value()) + str(y2.value())
directTab = {
'1000': 1,
'0001': 1,
'0111': 1,
'1110': 1,
'1011': -1,
'1101': -1,
'0100': -1,
'0010': -1
}
def setByte(i):
return i.to_bytes(1)
def limitNums(num, maxn, minn):
return max(minn, min(maxn, num))
def handleLEDs(intensity, value):
regen_in = pyb.ADC(Pin.cpu.A7)
# Outputs
# Conflict with Key (Kelly v1.0)
# buzzer = Pin(Pin.cpu.B0, Pin.OUT_PP)
pyb_red_led = LED(1)
pyb_green_led = LED(2)
pyb_blue_led = LED(4)
horn = Pin(Pin.cpu.C0, Pin.OUT_PP)
headlight = Pin(Pin.cpu.C1, Pin.OUT_PP)
key = Pin(Pin.cpu.B0, Pin.OUT_PP)
# DAC
throttle_out = DAC(1, bits=12)
regen_out = DAC(2, bits=12)
# Other
bike_on = False
light_on = False
horn_on = False
############### END PIN SETUP
def init():
# print("Initialize Buzzer")
# buzzer.low()
print("Initialize LEDs")
pyb_red_led.off()
from pyb import DAC
from array import array
import math
dac = DAC(1, bits=12, buffering=True) # use 12 bit resolution
dac.write(4095) # output maximum value, 3.3V
# To output a continuous sine-wave at 12-bit resolution:
# create a buffer containing a sine-wave, using half-word samples
buf = array("H", 2048 + int(2047 * math.sin(2 * math.pi * i / 128)) for i in range(128))
# output the sine-wave at 200Hz
dac.write_timed(buf, 200 * len(buf), mode=DAC.CIRCULAR)
# main.py -- put your code here! import pyb from pyb import DAC #----------DAC--------------# dac = DAC(1, bits=12) #X15 pin dac.write(4095) dac2 = DAC(2, bits=12) #X16 pin dac2.write(2048)
from pyb import DAC
import utime,math
dac = DAC(1,buffering=True) # create DAC 1 on pin X5
dac.write(128) # write a value to the DAC (makes X5 1.65V)
# To output a continuous sine-wave:
# create a buffer containing a sine-wave
buf = bytearray(100)
for i in range(len(buf)):
buf[i] = 128 + int(127 * math.sin(2 * math.pi * i / len(buf)))
# output the sine-wave at 400Hz
dac.write_timed(buf, 400 * len(buf), mode=DAC.CIRCULAR)
from pyb import Pin, ADC, UART, I2C, DAC
import char_lcd
import time
import math
import binascii
import pyb
from light import lightvalue
print("kek")
#Define sensors
tempsensor = ADC(Pin('X1'))
motionsensor = Pin('Y12', Pin.IN, Pin.PULL_UP)
beeper = DAC(1)
waterportion = Pin('X11', Pin.OUT_PP)
doortrigger = Pin('Y7', Pin.IN, Pin.PULL_UP)
doortrigger2 = Pin('Y8', Pin.IN, Pin.PULL_UP)
#Define UART bus and I2C bus
uart = UART(6, 115200)
i2c = I2C(1, I2C.MASTER, baudrate=9600)
i2c2 = I2C(2, I2C.MASTER, baudrate=9600)
#Define LCD
d = char_lcd.HD44780(i2c2)
def changetemp(temp):
#>>> volume(0) # minimum volume
#>>> volume(127) # maximum volume
#To play a sound, use the write_timed method of the DAC object. For example:
import math
from pyb import DAC
# create a buffer containing a sine-wave
buf = bytearray(100)
for i in range(len(buf)):
buf[i] = 128 + int(127 * math.sin(2 * math.pi * i / len(buf)))
# output the sine-wave at 400Hz
dac = DAC(1)
dac.write_timed(buf, 400 * len(buf), mode=DAC.CIRCULAR)
# or playing a wave file from the SD Card
import wave
from pyb import DAC
from pyb import delay
dac = DAC(1)
def play(filename):
f = wave.open(filename, 'r')
total_frames = f.getnframes()
framerate = f.getframerate()
import pyb, math
from array import array
import uio
from pyb import Pin, ADC, DAC
import time
tim = pyb.Timer(6, freq=10)
#buf = array('u',range(128))
# create a buffer containing a sine-wave, using half-word samples
buf_dac = array(
'H', 2048 + int(2047 * math.sin(2 * math.pi * i / 128))
for i in range(128))
buf_adc = array('H', range(128))
# output the sine-wave at 400Hz
dac = DAC(1, bits=12)
dac.write_timed(buf_dac, 128, mode=DAC.CIRCULAR)
adc = pyb.ADC(Pin('Y12')) # create an analog object from a pin
adc.ADCALL(bits=12)
adc.read_timed(buf_adc, tim)
file = uio.open('3.txt', mode='w')
file.write('DAC')
file.write(str(buf_dac))
file.write('ADC')
file.write(str(buf_adc))
file.close()
'''
import pyb, time
from pyb import LED, DAC, ADC, Pin, Timer
from oled_938 import OLED_938
from mpu6050 import MPU6050
from motor import MOTOR
from g24_pid_controller import PIDC
from array import array
from mic import MICROPHONE
from g24_choreo_functions import *
import micropython
micropython.alloc_emergency_exception_buf(100)
# Define ports, pins and peripherals
a_out = DAC(1, bits=12)
pot = ADC(Pin('X11'))
b_LED = LED(4)
# IMU connected to X9 and X10
imu = MPU6050(1, False)
# Use OLED to say what it is doing
oled = OLED_938(pinout={'sda': 'Y10', 'scl': 'Y9', 'res': 'Y8'}, height=64, external_vcc=False, i2c_devid=61)
oled.poweron()
oled.init_display()
oled.draw_text(0, 0, 'Group 24')
oled.draw_text(0,10, 'Balance & Dance')
oled.draw_text(0,20, 'Press USR button')
oled.display()
#import numpy as np
#import commpy.channelcoding.convcode as cc
#from commpy.utilities import dec2bitarray
import binascii
from pyb import DAC
import utime
#En esta prueba se crea un arreglo predefinido
#con decimales del 0 al 255 y se envia cada
#elemento del arreglo al DAC(1)
#***********************************************
# DAC parameters configuration
#***********************************************
dac = DAC(1, bits=8)
#***********************************************
#Conversion from text message into single decimal byte#
#***********************************************
msg = bytearray([
255, 255, 0, 0, 255, 255, 0, 0, 255, 255, 0, 0, 255, 255, 0, 0, 255, 255,
0, 0, 255, 255, 0, 0
])
#msg = bytearray([0, 0, 0, 0, 0, 0, 0, 0, 0, 255, 255, 255, 255, 255, 255, 255, 255, 255])
#Ascci converted to hex and then to dec
for s in range(len(msg)):
#msg_dec = int(binascii.hexlify(msg[s]), 16)
dac.write(msg[s])
print(msg)
print(len(msg))
# DAC Control Example
#
# This example shows how to use the DAC pin output onboard your OpenMV Cam.
import time
from pyb import DAC
dac = DAC("P6") # Must always be "P6".
while(True):
# The DAC has 8-12 bits of resolution (default 8-bits).
for i in range(256):
dac.write(i)
time.sleep_ms(20)
for i in range(256):
dac.write(255-i)
time.sleep_ms(20)
utime.sleep_ms(10)
#change baudrate
self.uart.init(baudrate=115200, bits=8, parity=None, stop=1)
self.load_payload(2)
#start callback - MAKE SURE YOU RESTART THE CHIP EVERY TIME (CMD D) to kill previous callbacks running
self.sendTimer.callback(self.sendCall)
return
micropython.alloc_emergency_exception_buf(200)
p_inw1 = Pin('X2', Pin.IN, Pin.PULL_DOWN)
p_inb2 = Pin('X3', Pin.IN, Pin.PULL_DOWN)
p_ing1 = Pin('X4', Pin.IN, Pin.PULL_DOWN)
led1 = DAC(Pin('X5'))
led2 = DAC(Pin('X6'))
red_led = pyb.LED(1)
green_led = pyb.LED(2)
red_led.on()
lpf2 = LPF2(1, 'Y1', 'Y2', timer=4, freq=5) # OpenMV
lpf2.initialize()
value = 0
# Loop
while True:
if not lpf2.connected:
lpf2.sendTimer.callback(None)
red_led.on()
