def __init__(self):
self.errorState = False # If an error has occured
self.switch = None
self.powerOn = False
self.active = False
self.target = 80
self.unit = 'X'
# self.sensor = sensors.temperaeratorSensor()
# Set a generic sensor, later swap for same sensor as boiler.
self.sensor = sensors.genericSensor()
def __init__(self):
self.errorState = False # If an error has occured
self.switch = None
self.powerOn = False
self.active = False
self.target = 80
self.unit = 'F'
# self.sensor = sensors.temperboilerValveSensor()
# Set a generic sensor, later swap for same sensor as boiler.
self.sensor = sensors.genericSensor()
self.actual = 0 # Actual measured value, ex temp
def __init__(self):
"""
Switch is not used, just to be consistent with other modules
"""
self.errorState = False # If an error has occured
self.actual = 0.0
self.target = 0.0
self.active = False
self.absminutes = time.localtime(time.time()).tm_sec / 60.0
self.unit = 'min'
self.powerOn = 'False'
self.sensor = sensors.genericSensor()
def __init__(self):
"""
Used to hold info about the controllerinfo
As example, this can hold controller type and name etc.
"""
self.errorState = False # If an error has occured
self.actual = 0.0
self.target = 0.0
self.active = False
self.unit = 'U'
self.powerOn = 'False'
self.sensor = sensors.genericSensor()
self.equipment = {}
def __init__(self):
"""
Constructor
multiple devices may require same switch collection
Note, controller can run but power
could be off, as example, heater goes
on and off, while controller is active
"""
self.errorState = False # If an error has occured
self.actual = 0 # Actual measured value, ex temp
self.target = 0 # Target value
self.unit = "U" # Unit of measure
self.powerOn = False # If the power is on heater/pump etc
self.active = False # Controller is running
self.switch = None # Switch object. Should have method on and off
self.sensor = sensors.genericSensor()
def __init__(self, number=1):
'''
Constructor
multiple devices may require same switch collection
Note, controller can run but power
could be off, as example, heater goes
on and off, while controller is active
'''
self.errorState = False # If an error has occured
self.deviceNumber = number
self.servo = str(number)
self.actual = full # Actual measured value, ex temp
self.target = full # Target value
self.unit = 'U' # Unit of measure
self.powerOn = False # If the power is on heater/pump etc
self.active = False # Controller is running
self.switch = None # Switch object. Should have method on and off
self.sensor = sensors.genericSensor()
try:
ret = subprocess.call('lsusb', stdout=open('/dev/null', 'w'),
stderr=subprocess.STDOUT)
except:
ret = 9
self.usbOK = (ret == 0)
scriptdir = os.path.dirname(os.path.abspath(__file__))
self.exe = scriptdir + '/../../UscCmd/UscCmd'
# If multiple dispensers are added, these values can be set in
# connectSwitch
if number % 2 == 1:
self.vFull = '8000'
self.vEmpty = '4000'
else:
self.vFull = '4000'
self.vEmpty = '8000'
self.exeFull = self.exe + ' --servo ' + self.servo + ',' + self.vFull
self.exeEmpty = self.exe + ' --servo ' + self.servo + ',' + self.vEmpty
self.move()
