def buttonState():
global showTimer
global poweroffTimer
global isDisplayCleared
inputState = GPIO.input(PIN_BTN)
if inputState == GPIO.HIGH:
showTimer = 0
isDisplayCleared = False
poweroffTimer += UPDATE_DELAY
else:
poweroffTimer = 0
if (poweroffTimer > POWEROFF_TIME):
shutdown()
return ()
try:
range = xrange
except NameError:
pass
try:
input = raw_input
except NameError:
pass
range_pins = [3, 24] #range of GPIO pins to check
inv_pins = [4, 6, 9, 14, 17, 20] #pins that aren't onboard GPIOs
v_modes = [GPIO.PUD_DOWN, GPIO.PUD_UP, GPIO.PUD_OFF] #Pull's states
v_modes_str = ["Down", "Up", "Off"]
GPIO.setmode(GPIO.BOARD)
def modetype(mode):
for pin in range(range_pins[0], range_pins[1] + 1):
if not pin in inv_pins:
GPIO.setup(pin, GPIO.IN, pull_up_down=mode)
print("value_%d = %d" % (pin, GPIO.input(pin)))
time.sleep(0.1)
while True:
try:
modenum = int(
input(
'Choose resistor pull modes: \n( 0 - Active Pull Down, 1 - Active Pull Up, 2 - Disable Pull, 3 - Quit )\n'
from __future__ import print_function
import NPi.GPIO as GPIO
validPins = [11,12,13,15]
GPIO.setmode(GPIO.BOARD)
GPIO.setup(11,GPIO.IN)
GPIO.setup(12,GPIO.OUT)
GPIO.setup(13,GPIO.IN)
GPIO.setup(15,GPIO.OUT)
for pin in validPins:
fun = GPIO.gpio_function(pin)
print(fun)
def setupGPIO():
GPIO.setwarnings(False) # Ignore warning for now
GPIO.setmode(GPIO.BOARD) # Use physical pin numbering
GPIO.setup(PIN_BTN, GPIO.IN, pull_up_down=GPIO.PUD_DOWN)
return ()
import NPi.GPIO as GPIO
import time
channel = 7
GPIO.setmode(GPIO.BOARD)
GPIO.setup(channel, GPIO.IN, GPIO.PUD_DOWN)
print(" Now input is Low\n Our task is performed when it becomes High")
while True:
if GPIO.input(channel):
print("Input was High,begin to perform")
print("Count Down")
for i in range(7, 0, -1):
print("%d" % i)
time.sleep(1)
print("Performed!")
exit()
def makehigh():
print("\n value_%d = %d\n" %(channel,GPIO.input(channel)))
GPIO.output(PIN_NUM,False)
print("\n value_%d = %d\n" %(PIN_NUM,GPIO.input(PIN_NUM)))
#!/usr/bin/env python
import NPi.GPIO as GPIO
import time
PIN_NUM = 7
GPIO.setmode(GPIO.BOARD)
GPIO.setup(PIN_NUM,GPIO.OUT)
while True:
print('Led aceso')
GPIO.output(PIN_NUM,True)
time.sleep(3)
GPIO.output(PIN_NUM,False)
print('led apagado')
time.sleep(3)
from __future__ import print_function
import NPi.GPIO as GPIO
import time
PIN_NUM = 12
GPIO.setmode(GPIO.BOARD)
GPIO.setup(PIN_NUM, GPIO.IN, GPIO.PUD_DOWN)
print("The value of Pin %d is %d" % (PIN_NUM, GPIO.input(PIN_NUM)))
def my_callback(channel):
print("Callback trigger %d" % channel)
print("Now value of the Pin is %d" % (GPIO.input(PIN_NUM)))
print("Click Ctr + C to exit")
GPIO.add_event_detect(PIN_NUM,
GPIO.RISING,
callback=my_callback,
bouncetime=300)
try:
while True:
time.sleep(0.1)
except KeyboardInterrupt:
pass
GPIO.cleanup()
#!/usr/bin/env python
from __future__ import print_function
import NPi.GPIO as GPIO
import time
GPIO.setmode(GPIO.BOARD)
GPIO.setup(7, GPIO.IN, pull_up_down=GPIO.PUD_UP)
print("\n value_7 = %d\n" % (GPIO.input(7)))
GPIO.setup(8, GPIO.IN, pull_up_down=GPIO.PUD_DOWN)
print("\n value_8 = %d\n" % (GPIO.input(8)))
GPIO.setup(12, GPIO.IN, pull_up_down=GPIO.PUD_UP)
print("\n value_12 = %d\n" % (GPIO.input(12)))
GPIO.setup(12, GPIO.IN, pull_up_down=GPIO.PUD_DOWN)
print("\n value_12 = %d\n" % (GPIO.input(12)))
#GPIO.cleanup()
#!/usr/bin/env python
from __future__ import print_function
import NPi.GPIO as GPIO
import time
from threading import Timer
SWITCH_PIN = 10
GPIO.setmode(GPIO.BOARD)
GPIO.setup(SWITCH_PIN, GPIO.IN, GPIO.PUD_DOWN)
print("\n value_%d = %d\n" % (SWITCH_PIN, GPIO.input(SWITCH_PIN)))
GPIO.add_event_detect(SWITCH_PIN, GPIO.RISING,
bouncetime=200) # add rising edge detection on a channel
switchcount = 0
while switchcount < 2:
if GPIO.event_detected(SWITCH_PIN):
switchcount += 1
print('Button pressed', switchcount)
print("\n value_%d = %d\n" % (SWITCH_PIN, GPIO.input(SWITCH_PIN)))
GPIO.remove_event_detect(SWITCH_PIN)
#!/usr/bin/env python
from __future__ import print_function
import NPi.GPIO as GPIO
import time
PIN_NUM = 8
GPIO.setmode(GPIO.BOARD)
GPIO.setup(PIN_NUM,GPIO.OUT)
GPIO.output(PIN_NUM,True)
print("\n value = %d\n" %(GPIO.input(PIN_NUM)))
time.sleep(1)
GPIO.output(PIN_NUM,False)
print("\n value = %d\n" %(GPIO.input(PIN_NUM)))
time.sleep(1)
GPIO.cleanup()
from __future__ import print_function
import NPi.GPIO as GPIO
validPins = [3, 5, 8, 7, 10, 12, 11, 13, 16, 15, 18, 19, 22, 21, 24, 23, 26]
GPIO.setmode(GPIO.BOARD)
for pin in validPins:
fun = GPIO.gpio_function(pin)
print(fun)
#/usr/bin/env python
import NPi.GPIO as GPIO
import time
try:
input = raw_input
except NameError:
pass
PIN_NUM = 11
GPIO.setmode(GPIO.BOARD)
GPIO.setup(PIN_NUM, GPIO.OUT)
p = GPIO.PWM(PIN_NUM, 0.5)
p.start(50)
input("Press Enter to stop:")
p.stop()
GPIO.cleanup()
def modetype(mode):
for pin in range(range_pins[0], range_pins[1] + 1):
if not pin in inv_pins:
GPIO.setup(pin, GPIO.IN, pull_up_down=mode)
print("value_%d = %d" % (pin, GPIO.input(pin)))
time.sleep(0.1)
import NPi.GPIO as GPIO
import time
PIN_NUM = 12
GPIO.setmode(GPIO.BOARD)
GPIO.setup(PIN_NUM, GPIO.OUT)
frequency = 50
p = GPIO.PWM(PIN_NUM, frequency)
p.start(0)
try:
while True:
for dutyCycle in range(0, 100, 5):
p.ChangeDutyCycle(dutyCycle)
time.sleep(0.1)
for dutyCycle in range(100, 0, -5):
p.ChangeDutyCycle(dutyCycle)
time.sleep(0.1)
except KeyboardInterrupt:
pass
p.stop()
GPIO.cleanup()
"Error importing GPIO modules! This is probably because you need superuser privileges. You can achieve this by using 'sudo' to run your script"
)
sys.exit(-1)
import time
try:
input = raw_input
except NameError:
pass
print("Inizializing...\n")
range_pins = [3, 24] #range of board GPIO pins to check
inv_pins = [4, 6, 9, 14, 17, 20] #pins that aren't onboard GPIOs
v_modes_str = ["LOW", "HIGH"]
GPIO.setmode(GPIO.BOARD)
time.sleep(0.2)
#print "Board revision:"
#print GPIO.RPI_INFO
#print GPIO.RPI_REVISION
print("\nNPi.GPIO version:")
print(GPIO.VERSION)
time.sleep(1)
while True:
try:
pin = int(
input(
#!/usr/bin/env python
from __future__ import print_function
import NPi.GPIO as GPIO
import time
from threading import Timer
PIN_NUM = 12
channel = 7
GPIO.setmode(GPIO.BOARD)
GPIO.setup(PIN_NUM,GPIO.OUT)
GPIO.output(PIN_NUM,True)
print("\n value_%d = %d\n" %(PIN_NUM,GPIO.input(PIN_NUM)))
GPIO.setup(channel,GPIO.IN,GPIO.PUD_DOWN)
print("\n value_%d = %d\n" %(channel,GPIO.input(channel)))
def makehigh():
print("\n value_%d = %d\n" %(channel,GPIO.input(channel)))
GPIO.output(PIN_NUM,False)
print("\n value_%d = %d\n" %(PIN_NUM,GPIO.input(PIN_NUM)))
GPIO.wait_for_edge(channel, GPIO.RISING)
t = Timer(1,makehigh)
t.start()
def my_callback(channel):
print("Callback trigger %d" % channel)
print("Now value of the Pin is %d" % (GPIO.input(PIN_NUM)))
print("Click Ctr + C to exit")
pinSW = 8
# PATH File
fileAip = '/media/AIP/Cut-01.csv'
fileCut = '/media/CuttingMachine/'
# Config Mount I/O to Windows
cutDrive = 'sudo mount.cifs //PathCutting/data /media/AIP -o rw,uid=pi,password=eseuser'
aipDrive = 'sudo mount.cifs //PathAIP/data /nedia/AIP -o rw,uid=pi,password=eseuser'
# Config CSV
mt = 'MT'
yd = 'YD'
header = [yd,mt]
GPIO.setmode(GPIO.BOARD)
GPIO.setup(pinSW,GPIO.IN)
reader = csv.reader(open("csvfile.csv"), delimiter=";")
included_cols = [22]
count = 0
content = []
def openFile():
# os.system(cutDrive)
now = datetime.now() # current date and time
nowdate = now.strftime("%Y%m%d")
fileReport = 'Reporting_' + nowdate + '-Job.csv'
while (os.path.ismount('/media/AIP') == False):
os.system(cutDrive)
try: