def cmd_rx(outfile, frequency, rate, gain, num_samples, device=None,
channel=_bladerf.CHANNEL_RX(0), **kwargs):
b = _bladerf.BladeRF(device)
ch = b.Channel(channel)
# Get underlying binary stream for stdout case
if isinstance(outfile, io.TextIOWrapper):
outfile = outfile.buffer
# Configure BladeRF
ch.frequency = frequency
ch.sample_rate = rate
ch.gain = gain
# Setup synchronous stream
b.sync_config(layout=_bladerf.ChannelLayout.RX_X1,
fmt=_bladerf.Format.SC16_Q11,
num_buffers=16,
buffer_size=8192,
num_transfers=8,
stream_timeout=3500)
# Enable module
ch.enable = True
# Create buffer
bytes_per_sample = 4
buf = bytearray(1024*bytes_per_sample)
num_samples_read = 0
try:
while True:
if num_samples > 0 and num_samples_read == num_samples:
break
elif num_samples > 0:
num = min(len(buf)//bytes_per_sample,
num_samples-num_samples_read)
else:
num = len(buf)//bytes_per_sample
# Read into buffer
b.sync_rx(buf, num)
num_samples_read += num
# Write to file
outfile.write(buf[:num*bytes_per_sample])
except KeyboardInterrupt:
pass
# Disable module
ch.enable = False
b.close()
outfile.close()
def _print_cmd_info(device=None, devinfo=None, verbose=False):
b = _bladerf.BladeRF(device, devinfo)
devinfo = b.get_devinfo()
flash_size, fs_guessed = b.flash_size
if verbose:
print("Object ", repr(b))
print("Board Name ", b.board_name)
print("Device Speed ", b.device_speed.name)
print("FPGA Size ", b.fpga_size)
print("FPGA Configured ", b.fpga_configured)
if b.is_fpga_configured():
print("FPGA Version ", b.fpga_version)
else:
print("FPGA Version ", "Not Configured")
print("Flash Size ", (flash_size>>17), "Mbit",
"(assumed)" if fs_guessed else "")
print("Firmware Version ", b.fw_version)
if verbose:
print("Clock Select ", b.clock_select)
print("Clock Output ", _bool_to_onoff(b.clock_output))
print("Power Source ", b.power_source)
print("Bus Voltage {:.3f} V".format(b.bus_voltage or 0))
print("Bus Current {:.3f} A".format(b.bus_current or 0))
print("Bus Power {:.3f} W".format(b.bus_power or 0))
print("RFIC temperature {:.3f} C".format(b.rfic_temperature or 0))
print("Loopback ", b.loopback)
print(" Modes ", _strify_list(b.loopback_modes))
print("RX Mux ", b.rx_mux)
print("PLL Mode ", _bool_to_onoff(b.pll_enable))
if b.pll_enable:
print("PLL Refclk ", b.pll_refclk)
print("PLL Locked ", _bool_to_onoff(b.pll_locked))
print("RX Channel Count ", b.rx_channel_count)
for c in range(b.rx_channel_count):
ch = b.Channel(_bladerf.CHANNEL_RX(c))
_print_channel_details(ch, verbose)
print("TX Channel Count ", b.tx_channel_count)
for c in range(b.tx_channel_count):
ch = b.Channel(_bladerf.CHANNEL_TX(c))
_print_channel_details(ch, verbose)
b.close()
'device': b,
'channel': tx_ch,
'freq': tx_freq,
'rate': tx_rate,
'gain': tx_gain,
'tx_start': None,
'rx_done': None,
'txfile': tx_file,
'repeat': tx_rpt
}).get()
if (status < 0):
print("Transmit operation failed with error " + str(status))
elif (s == board_name + '-rx'):
rx_ch = _bladerf.CHANNEL_RX(config.getint(s, 'rx_channel'))
rx_freq = int(config.getfloat(s, 'rx_frequency'))
rx_rate = int(config.getfloat(s, 'rx_samplerate'))
rx_gain = int(config.getfloat(s, 'rx_gain'))
rx_ns = int(config.getfloat(s, 'rx_num_samples'))
rx_file = config.get(s, 'rx_file')
# Make this blocking for now ...
status = rx_pool.apply_async(
receive, (), {
'device': b,
'channel': rx_ch,
'freq': rx_freq,
'rate': rx_rate,
'gain': rx_gain,
'tx_start': None,
