def __init__(self):
'Set the default settings, execute title & settings fileName.'
skeinforge_profile.addListsToCraftTypeRepository('skeinforge_application.skeinforge_plugins.craft_plugins.cool.html', self )
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Cool', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Cool')
self.activateCool = settings.BooleanSetting().getFromValue('Activate Cool', self, True)
self.bridgeCool = settings.FloatSpin().getFromValue(0.0, 'Bridge Cool (Celcius):', self, 10.0, 1.0)
self.coolType = settings.MenuButtonDisplay().getFromName('Cool Type:', self)
self.orbit = settings.MenuRadio().getFromMenuButtonDisplay(self.coolType, 'Orbit', self, False)
self.slowDown = settings.MenuRadio().getFromMenuButtonDisplay(self.coolType, 'Slow Down', self, True)
self.maximumCool = settings.FloatSpin().getFromValue(0.0, 'Maximum Cool (Celcius):', self, 10.0, 2.0)
self.minimumLayerTime = settings.FloatSpin().getFromValue(0.0, 'Minimum Layer Time (seconds):', self, 120.0, 60.0)
self.minimumOrbitalRadius = settings.FloatSpin().getFromValue(
0.0, 'Minimum Orbital Radius (millimeters):', self, 20.0, 10.0)
settings.LabelSeparator().getFromRepository(self)
settings.LabelDisplay().getFromName('- Name of Alteration Files -', self )
self.nameOfCoolEndFile = settings.StringSetting().getFromValue('Name of Cool End File:', self, 'cool_end.gcode')
self.nameOfCoolStartFile = settings.StringSetting().getFromValue('Name of Cool Start File:', self, 'cool_start.gcode')
settings.LabelSeparator().getFromRepository(self)
self.turnFanOnAtBeginning = settings.BooleanSetting().getFromValue('Turn Fan On at Beginning', self, True)
self.turnFanOffAtEnding = settings.BooleanSetting().getFromValue('Turn Fan Off at Ending', self, True)
self.executeTitle = 'Cool'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.reversal.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Reversal', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Reversal'
)
self.activateReversal = settings.BooleanSetting().getFromValue(
'Activate Reversal', self, False)
self.reversalRPM = settings.FloatSpin().getFromValue(
2, 'Reversal speed (RPM):', self, 50, 35)
self.reversalTime = settings.FloatSpin().getFromValue(
10, 'Reversal time (milliseconds):', self, 1000, 75)
self.pushbackTime = settings.FloatSpin().getFromValue(
10, 'Push-back time (milliseconds):', self, 1000, 75)
self.reversalThreshold = settings.FloatSpin().getFromValue(
0.1, 'Reversal threshold (mm):', self, 5.0, 1.0)
self.activateEarlyReversal = settings.BooleanSetting().getFromValue(
'Activate early reversal and push-back', self, True)
self.executeTitle = 'Reversal'
def __init__(self):
'Set the default settings, execute title & settings fileName.'
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.widen.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Widen', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Widen')
self.activateWiden = settings.BooleanSetting().getFromValue(
'Activate Widen', self, False)
self.widenWidthOverEdgeWidth = settings.IntSpin().getFromValue(
2, 'Widen Width over Edge Width (ratio):', self, 4, 2)
self.executeTitle = 'Widen'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.preface.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Preface', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Preface')
self.meta = settings.StringSetting().getFromValue('Meta:', self, '')
self.setPositioningToAbsolute = settings.BooleanSetting().getFromValue(
'Set Positioning to Absolute', self, True)
self.setUnitsToMillimeters = settings.BooleanSetting().getFromValue(
'Set Units to Millimeters', self, True)
self.startAtHome = settings.BooleanSetting().getFromValue(
'Start at Home', self, False)
settings.LabelSeparator().getFromRepository(self)
settings.LabelDisplay().getFromName('- Turn Extruder Off -', self)
self.turnExtruderOffAtShutDown = settings.BooleanSetting(
).getFromValue('Turn Extruder Off at Shut Down', self, True)
self.turnExtruderOffAtStartUp = settings.BooleanSetting().getFromValue(
'Turn Extruder Off at Start Up', self, True)
self.executeTitle = 'Preface'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.lift.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File to be Lifted', self, '')
self.activateLift = settings.BooleanSetting().getFromValue(
'Activate Lift', self, True)
self.cuttingLiftOverLayerStep = settings.FloatSpin().getFromValue(
-1.0, 'Cutting Lift over Layer Step (ratio):', self, 1.0, -0.5)
self.clearanceAboveTop = settings.FloatSpin().getFromValue(
0.0, 'Clearance above Top (mm):', self, 10.0, 5.0)
self.executeTitle = 'Lift'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.comb.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Comb', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Comb')
self.activateComb = settings.BooleanSetting().getFromValue(
'Activate Comb', self, False)
self.runningJumpSpace = settings.FloatSpin().getFromValue(
0.0, 'Running Jump Space (mm):', self, 5.0, 2.0)
self.executeTitle = 'Comb'
def __init__(self):
'Set the default settings, execute title & settings fileName.'
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.limit.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Limit', self, '')
self.activateLimit = settings.BooleanSetting().getFromValue(
'Activate Limit', self, True)
self.maximumInitialFeedRate = settings.FloatSpin().getFromValue(
0.5, 'Maximum Initial Feed Rate (mm/s):', self, 10.0, 1.0)
self.maximumZFeedRatePerSecond = settings.FloatSpin().getFromValue(
0.5, 'Maximum Z Feed Rate (mm/s):', self, 10.0, 1.0)
self.executeTitle = 'Limit'
def __init__(self):
'Set the default settings, execute title & settings fileName.'
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.jitter.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Jitter', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Jitter')
self.activateJitter = settings.BooleanSetting().getFromValue(
'Activate Jitter', self, True)
self.jitterOverEdgeWidth = settings.FloatSpin().getFromValue(
1.0, 'Jitter Over Perimeter Width (ratio):', self, 3.0, 2.0)
self.executeTitle = 'Jitter'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.home.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Home', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Home')
self.activateHome = settings.BooleanSetting().getFromValue(
'Activate Home', self, False)
self.nameOfHomeFile = settings.StringSetting().getFromValue(
'Name of Home File:', self, 'home.gcode')
self.executeTitle = 'Home'
def __init__(self):
'Set the default settings, execute title & settings fileName.'
skeinforge_profile.addListsToCraftTypeRepository('skeinforge_application.skeinforge_plugins.craft_plugins.dimension.html', self )
self.fileNameInput = settings.FileNameInput().getFromFileName( fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Dimension', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute('http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Dimension')
self.activateDimension = settings.BooleanSetting().getFromValue('Activate Dimension', self, False )
extrusionDistanceFormatLatentStringVar = settings.LatentStringVar()
self.extrusionDistanceFormatChoiceLabel = settings.LabelDisplay().getFromName('Extrusion Distance Format Choice: ', self )
settings.Radio().getFromRadio( extrusionDistanceFormatLatentStringVar, 'Absolute Extrusion Distance', self, True )
self.relativeExtrusionDistance = settings.Radio().getFromRadio( extrusionDistanceFormatLatentStringVar, 'Relative Extrusion Distance', self, False )
self.extruderRetractionSpeed = settings.FloatSpin().getFromValue( 4.0, 'Extruder Retraction Speed (mm/s):', self, 34.0, 13.3 )
settings.LabelSeparator().getFromRepository(self)
settings.LabelDisplay().getFromName('- Filament -', self )
self.filamentDiameter = settings.FloatSpin().getFromValue(1.0, 'Filament Diameter (mm):', self, 6.0, 2.8)
self.filamentPackingDensity = settings.FloatSpin().getFromValue(0.7, 'Filament Packing Density (ratio):', self, 1.0, 0.85)
settings.LabelSeparator().getFromRepository(self)
self.maximumEValueBeforeReset = settings.FloatSpin().getFromValue(0.0, 'Maximum E Value before Reset (float):', self, 999999.9, 91234.0)
self.minimumTravelForRetraction = settings.FloatSpin().getFromValue(0.0, 'Minimum Travel for Retraction (millimeters):', self, 2.0, 1.0)
self.retractWithinIsland = settings.BooleanSetting().getFromValue('Retract Within Island', self, False)
self.disableRetractWithinInfill = settings.BooleanSetting().getFromValue('Disable Retract Within Infill', self, False)
self.retractOnLayerChange = settings.BooleanSetting().getFromValue('Retract On Layer Change', self, False)
self.retractionDistance = settings.FloatSpin().getFromValue( 0.0, 'Retraction Distance (millimeters):', self, 100.0, 0.0 )
self.restartExtraDistance = settings.FloatSpin().getFromValue( 0.0, 'Restart Extra Distance (millimeters):', self, 100.0, 0.0 )
self.executeTitle = 'Dimension'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.fillet.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File to be Filleted', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Fillet')
self.activateFillet = settings.BooleanSetting().getFromValue(
'Activate Fillet', self, False)
self.filletProcedureChoiceLabel = settings.LabelDisplay().getFromName(
'Fillet Procedure Choice: ', self)
filletLatentStringVar = settings.LatentStringVar()
self.arcPoint = settings.Radio().getFromRadio(filletLatentStringVar,
'Arc Point', self, False)
self.arcRadius = settings.Radio().getFromRadio(filletLatentStringVar,
'Arc Radius', self,
False)
self.arcSegment = settings.Radio().getFromRadio(
filletLatentStringVar, 'Arc Segment', self, False)
self.bevel = settings.Radio().getFromRadio(filletLatentStringVar,
'Bevel', self, True)
self.cornerFeedRateMultiplier = settings.FloatSpin().getFromValue(
0.8, 'Corner Feed Rate Multiplier (ratio):', self, 1.2, 1.0)
self.filletRadiusOverEdgeWidth = settings.FloatSpin().getFromValue(
0.25, 'Fillet Radius over Perimeter Width (ratio):', self, 0.65,
0.35)
self.reversalSlowdownDistanceOverEdgeWidth = settings.FloatSpin(
).getFromValue(
0.3, 'Reversal Slowdown Distance over Perimeter Width (ratio):',
self, 0.7, 0.5)
self.useIntermediateFeedRateInCorners = settings.BooleanSetting(
).getFromValue('Use Intermediate Feed Rate in Corners', self, True)
self.executeTitle = 'Fillet'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.drill.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Drill', self, '')
self.activateDrill = settings.BooleanSetting().getFromValue(
'Activate Drill', self, True)
self.drillingMarginOnBottom = settings.FloatSpin().getFromValue(
0.0, 'Drilling Margin on Bottom (millimeters):', self, 5.0, 1.0)
self.drillingMarginOnTop = settings.FloatSpin().getFromValue(
0.0, 'Drilling Margin on Top (millimeters):', self, 20.0, 3.0)
self.executeTitle = 'Drill'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.bottom.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Bottom', self, '')
self.activateBottom = settings.BooleanSetting().getFromValue(
'Activate Bottom:', self, True)
self.altitude = settings.FloatSpin().getFromValue(
-1.0, 'Altitude (mm):', self, 1.0, 0.0)
self.svgViewer = settings.StringSetting().getFromValue(
'SVG Viewer:', self, 'webbrowser')
self.executeTitle = 'Bottom'
def __init__(self):
'Set the default settings, execute title & settings fileName.'
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.limit.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Limit', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Limit')
self.activateLimit = settings.BooleanSetting().getFromValue(
'Activate Limit', self, False)
self.maximumInitialFeedRate = settings.FloatSpin().getFromValue(
0.5, 'Maximum Initial Feed Rate (mm/s):', self, 10.0, 1.0)
self.executeTitle = 'Limit'
def __init__( self ): "Set the default settings, execute title & settings fileName." skeinforge_profile.addListsToCraftTypeRepository( 'skeinforge_plugins.craft_plugins.chop.html', self ) self.fileNameInput = settings.FileNameInput().getFromFileName( fabmetheus_interpret.getTranslatorFileTypeTuples(), 'Open File to be Chopped', self, '' ) self.addExtraTopLayerIfNecessary = settings.BooleanSetting().getFromValue( 'Add Extra Top Layer if Necessary', self, True ) self.extraDecimalPlaces = settings.IntSpin().getFromValue( 0, 'Extra Decimal Places (integer):', self, 2, 1 ) self.importCoarseness = settings.FloatSpin().getFromValue( 0.5, 'Import Coarseness (ratio):', self, 2.0, 1.0 ) self.layerThickness = settings.FloatSpin().getFromValue( 0.1, 'Layer Thickness (mm):', self, 1.0, 0.4 ) self.layersFrom = settings.IntSpin().getFromValue( 0, 'Layers From (index):', self, 20, 0 ) self.layersTo = settings.IntSpin().getSingleIncrementFromValue( 0, 'Layers To (index):', self, 912345678, 912345678 ) self.meshTypeLabel = settings.LabelDisplay().getFromName( 'Mesh Type: ', self, ) importLatentStringVar = settings.LatentStringVar() self.correctMesh = settings.Radio().getFromRadio( importLatentStringVar, 'Correct Mesh', self, True ) self.unprovenMesh = settings.Radio().getFromRadio( importLatentStringVar, 'Unproven Mesh', self, False ) self.perimeterWidth = settings.FloatSpin().getFromValue( 0.4, 'Perimeter Width (mm):', self, 4.0, 2.0 ) self.executeTitle = 'Chop'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge.skeinforge_tools.craft_plugins.hop.html', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Hop', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Hop')
self.activateHop = settings.BooleanSetting().getFromValue(
'Activate Hop', self, False)
self.hopOverLayerThickness = settings.FloatSpin().getFromValue(
0.5, 'Hop Over Layer Thickness (ratio):', self, 1.5, 1.0)
self.minimumHopAngle = settings.FloatSpin().getFromValue(
20.0, 'Minimum Hop Angle (degrees):', self, 60.0, 30.0)
self.executeTitle = 'Hop'
def __init__(self):
'Set the default settings, execute title & settings fileName.'
skeinforge_profile.addListsToCraftTypeRepository('skeinforge_application.skeinforge_plugins.craft_plugins.leadin.html', self )
self.fileNameInput = settings.FileNameInput().getFromFileName( fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Leadin', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute('http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Leadin')
self.activateLeadin = settings.BooleanSetting().getFromValue('Activate Leadin', self, False )
self.clipOverPerimeterWidth = settings.FloatSpin().getFromValue(0.5, 'Clip Over Perimeter Width (ratio):', self,1.5, 1.0)
settings.LabelSeparator().getFromRepository(self)
settings.LabelDisplay().getFromName('- Infill -', self )
self.infillBottomFeedRate = settings.FloatSpin().getFromValue(0.2, 'Infill Bottom Feed Rate Multiplier (ratio):', self, 2.0, 1.0)
self.infillBottomFlowRate = settings.FloatSpin().getFromValue(0.2, 'Infill Bottom Flow Rate Multiplier (ratio):', self, 2.0, 1.0)
self.infillTopFeedRate = settings.FloatSpin().getFromValue(0.2, 'Infill Top Feed Rate Multiplier (ratio):', self, 2.0, 1.0)
self.infillTopFlowRate = settings.FloatSpin().getFromValue(0.2, 'Infill Top Flow Rate Multiplier (ratio):', self, 2.0, 1.0)
settings.LabelSeparator().getFromRepository(self)
self.layersFrom = settings.IntSpin().getSingleIncrementFromValue(0, 'Layers From (index):', self, 912345678, 1)
self.executeTitle = 'Leadin'
def __init__(self):
'Set the default settings, execute title & settings fileName.'
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.joris.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Joris', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Joris')
self.activateJoris = settings.BooleanSetting().getFromValue(
'Activate Joris', self, False)
settings.LabelSeparator().getFromRepository(self)
self.layersFrom = settings.IntSpin().getSingleIncrementFromValue(
0, 'Layers From (index):', self, 912345678, 1)
self.executeTitle = 'Joris'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository('skeinforge_application.skeinforge_plugins.craft_plugins.chamber.html', self )
self.fileNameInput = settings.FileNameInput().getFromFileName( fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Chamber', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute('http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Chamber')
self.activateChamber = settings.BooleanSetting().getFromValue('Activate Chamber', self, False )
settings.LabelSeparator().getFromRepository(self)
settings.LabelDisplay().getFromName('- Bed -', self )
self.bedTemperature = settings.FloatSpin().getFromValue(20.0, 'Bed Temperature (Celcius):', self, 90.0, 60.0)
self.bedTemperatureBeginChangeHeight = settings.FloatSpin().getFromValue(-1.0, 'Bed Temperature Begin Change Height (mm):', self, 20.0, -1.0)
self.bedTemperatureEndChangeHeight = settings.FloatSpin().getFromValue(-1.0, 'Bed Temperature End Change Height (mm):', self, 40.0, -1.0)
self.bedTemperatureEnd = settings.FloatSpin().getFromValue(20.0, 'Bed Temperature End (Celcius):', self, 90.0, 20.0)
settings.LabelSeparator().getFromRepository(self)
self.chamberTemperature = settings.FloatSpin().getFromValue( 20.0, 'Chamber Temperature (Celcius):', self, 90.0, 30.0 )
self.holdingForce = settings.FloatSpin().getFromValue( 0.0, 'Holding Force (bar):', self, 100.0, 0.0 )
self.executeTitle = 'Chamber'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository('skeinforge_application.skeinforge_plugins.craft_plugins.stretch.html', self )
self.fileNameInput = settings.FileNameInput().getFromFileName( fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Stretch', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute('http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Stretch')
self.activateStretch = settings.BooleanSetting().getFromValue('Activate Stretch', self, False )
self.crossLimitDistanceOverPerimeterWidth = settings.FloatSpin().getFromValue( 3.0, 'Cross Limit Distance Over Perimeter Width (ratio):', self, 10.0, 5.0 )
self.loopStretchOverPerimeterWidth = settings.FloatSpin().getFromValue( 0.05, 'Loop Stretch Over Perimeter Width (ratio):', self, 0.25, 0.11 )
self.pathStretchOverPerimeterWidth = settings.FloatSpin().getFromValue( 0.0, 'Path Stretch Over Perimeter Width (ratio):', self, 0.2, 0.0 )
settings.LabelSeparator().getFromRepository(self)
settings.LabelDisplay().getFromName('- Perimeter -', self )
self.perimeterInsideStretchOverPerimeterWidth = settings.FloatSpin().getFromValue( 0.12, 'Perimeter Inside Stretch Over Perimeter Width (ratio):', self, 0.52, 0.32 )
self.perimeterOutsideStretchOverPerimeterWidth = settings.FloatSpin().getFromValue( 0.05, 'Perimeter Outside Stretch Over Perimeter Width (ratio):', self, 0.25, 0.1 )
settings.LabelSeparator().getFromRepository(self)
self.stretchFromDistanceOverPerimeterWidth = settings.FloatSpin().getFromValue( 1.0, 'Stretch From Distance Over Perimeter Width (ratio):', self, 3.0, 2.0 )
self.executeTitle = 'Stretch'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.carve.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getTranslatorFileTypeTuples(),
'Open File for Carve', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Carve')
self.addLayerTemplateToSVG = settings.BooleanSetting().getFromValue(
'Add Layer Template to SVG', self, True)
self.edgeWidth = settings.FloatSpin().getFromValue(
0.1, 'Edge Width (mm):', self, 2.2, 0.4)
self.extraDecimalPlaces = settings.FloatSpin().getFromValue(
0.0, 'Extra Decimal Places (float):', self, 3.0, 2.0)
self.importCoarseness = settings.FloatSpin().getFromValue(
0.5, 'Import Coarseness (ratio):', self, 2.0, 1.0)
self.layerHeight = settings.FloatSpin().getFromValue(
0.1, 'Layer Height (mm):', self, 1.0, 0.2)
settings.LabelSeparator().getFromRepository(self)
settings.LabelDisplay().getFromName('- Layers -', self)
self.layersFrom = settings.IntSpin().getFromValue(
0, 'Layers From (index):', self, 20, 0)
self.layersTo = settings.IntSpin().getSingleIncrementFromValue(
0, 'Layers To (index):', self, 912345678, 912345678)
settings.LabelSeparator().getFromRepository(self)
self.meshTypeLabel = settings.LabelDisplay().getFromName(
'Mesh Type: ', self)
importLatentStringVar = settings.LatentStringVar()
self.correctMesh = settings.Radio().getFromRadio(
importLatentStringVar, 'Correct Mesh', self, True)
self.unprovenMesh = settings.Radio().getFromRadio(
importLatentStringVar, 'Unproven Mesh', self, False)
self.svgViewer = settings.StringSetting().getFromValue(
'SVG Viewer:', self, 'webbrowser')
settings.LabelSeparator().getFromRepository(self)
self.executeTitle = 'Carve'
self.centerX = settings.FloatSpin().getFromValue(
0.0, 'CenterX', self, 1000.0, 0.0)
self.centerY = settings.FloatSpin().getFromValue(
0.0, 'CenterY', self, 1000.0, 0.0)
self.matrix = settings.StringSetting().getFromValue(
'ObjectMatrix', self, '1,0,0,0,1,0,0,0,1')
self.alternativeCenter = settings.StringSetting().getFromValue(
'AlternativeCenterFile', self, '')
def __init__(self):
"Set the default settings, execute title & settings fileName."
settings.addListsToRepository(
'skeinforge.skeinforge_tools.craft_plugins.unpause.html', '', self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Unpause', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Unpause'
)
self.activateUnpause = settings.BooleanSetting().getFromValue(
'Activate Unpause', self, False)
self.delay = settings.FloatSpin().getFromValue(
2.0, 'Delay (milliseconds):', self, 42.0, 28.0)
self.maximumSpeed = settings.FloatSpin().getFromValue(
1.1, 'Maximum Speed (ratio):', self, 1.9, 1.3)
self.executeTitle = 'Unpause'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.lash.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Lash', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Lash')
self.activateLash = settings.BooleanSetting().getFromValue(
'Activate Lash', self, False)
self.xBacklash = settings.FloatSpin().getFromValue(
0.1, 'X Backlash (mm):', self, 0.5, 0.2)
self.yBacklash = settings.FloatSpin().getFromValue(
0.1, 'Y Backlash (mm):', self, 0.5, 0.3)
self.executeTitle = 'Lash'
def __init__(self):
'Set the default settings, execute title & settings fileName.'
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.analyze_plugins.clairvoyance.html',
self)
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Clairvoyance'
)
self.activateClairvoyance = settings.BooleanSetting().getFromValue(
'Activate Clairvoyance', self, False)
settings.LabelSeparator().getFromRepository(self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
[('Gcode text files', '*.gcode')],
'Open File to Generate Clairvoyances for', self, '')
self.gcodeProgram = settings.StringSetting().getFromValue(
'Gcode Program:', self, 'webbrowser')
self.executeTitle = 'Clairvoyance'
def __init__(self):
'Set the default settings, execute title & settings fileName.'
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.smooth.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Smooth', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute(
'http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge_Smooth')
self.activateSmooth = settings.BooleanSetting().getFromValue(
'Activate Smooth', self, False)
self.layersFrom = settings.IntSpin().getSingleIncrementFromValue(
0, 'Layers From (index):', self, 912345678, 1)
self.maximumShorteningOverWidth = settings.FloatSpin().getFromValue(
0.2, 'Maximum Shortening over Width (float):', self, 2.0, 1.2)
self.executeTitle = 'Smooth'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.scale.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Scale', self, '')
self.activateScale = settings.BooleanSetting().getFromValue(
'Activate Scale:', self, False)
self.xyPlaneScale = settings.FloatSpin().getFromValue(
0.99, 'XY Plane Scale (ratio):', self, 1.03, 1.01)
self.zAxisScale = settings.FloatSpin().getFromValue(
0.99, 'Z Axis Scale (ratio):', self, 1.02, 1.0)
self.svgViewer = settings.StringSetting().getFromValue(
'SVG Viewer:', self, 'webbrowser')
self.executeTitle = 'Scale'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository('skeinforge_application.skeinforge_plugins.craft_plugins.cleave.html', self )
self.fileNameInput = settings.FileNameInput().getFromFileName( fabmetheus_interpret.getTranslatorFileTypeTuples(), 'Open File to be Cleaved', self, '')
self.addLayerTemplateToSVG = settings.BooleanSetting().getFromValue('Add Layer Template to SVG', self, True)
self.edgeWidth = settings.FloatSpin().getFromValue( 0.4, 'Edge Width (mm):', self, 4.0, 2.0 )
self.extraDecimalPlaces = settings.FloatSpin().getFromValue(0.0, 'Extra Decimal Places (float):', self, 3.0, 2.0)
self.importCoarseness = settings.FloatSpin().getFromValue( 0.5, 'Import Coarseness (ratio):', self, 2.0, 1.0 )
self.layerHeight = settings.FloatSpin().getFromValue( 0.1, 'Layer Height (mm):', self, 1.0, 0.4 )
self.layersFrom = settings.IntSpin().getFromValue( 0, 'Layers From (index):', self, 20, 0 )
self.layersTo = settings.IntSpin().getSingleIncrementFromValue( 0, 'Layers To (index):', self, 912345678, 912345678 )
self.meshTypeLabel = settings.LabelDisplay().getFromName('Mesh Type: ', self, )
importLatentStringVar = settings.LatentStringVar()
self.correctMesh = settings.Radio().getFromRadio( importLatentStringVar, 'Correct Mesh', self, True )
self.unprovenMesh = settings.Radio().getFromRadio( importLatentStringVar, 'Unproven Mesh', self, False )
self.svgViewer = settings.StringSetting().getFromValue('SVG Viewer:', self, 'webbrowser')
settings.LabelSeparator().getFromRepository(self)
self.executeTitle = 'Cleave'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository('skeinforge_application.skeinforge_plugins.craft_plugins.splodge.html', self )
self.fileNameInput = settings.FileNameInput().getFromFileName( fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(), 'Open File for Splodge', self, '')
self.openWikiManualHelpPage = settings.HelpPage().getOpenFromAbsolute('http://www.bitsfrombytes.com/wiki/index.php?title=Skeinforge_Splodge')
self.activateSplodge = settings.BooleanSetting().getFromValue('Activate Splodge', self, False )
settings.LabelSeparator().getFromRepository(self)
settings.LabelDisplay().getFromName('- Initial -', self )
self.initialLiftOverExtraThickness = settings.FloatSpin().getFromValue( 0.5, 'Initial Lift over Extra Thickness (ratio):', self, 1.5, 1.0 )
self.initialSplodgeFeedRate = settings.FloatSpin().getFromValue( 0.4, 'Initial Splodge Feed Rate (mm/s):', self, 2.4, 1.0 )
self.initialSplodgeQuantityLength = settings.FloatSpin().getFromValue( 10.0, 'Initial Splodge Quantity Length (millimeters):', self, 90.0, 30.0 )
settings.LabelSeparator().getFromRepository(self)
settings.LabelDisplay().getFromName('- Operating -', self )
self.operatingLiftOverExtraThickness = settings.FloatSpin().getFromValue( 0.5, 'Operating Lift over Extra Thickness (ratio):', self, 1.5, 1.0 )
self.operatingSplodgeFeedRate = settings.FloatSpin().getFromValue( 0.4, 'Operating Splodge Feed Rate (mm/s):', self, 2.4, 1.0 )
self.operatingSplodgeQuantityLength = settings.FloatSpin().getFromValue( 0.4, 'Operating Splodge Quantity Length (millimeters):', self, 2.4, 1.0 )
settings.LabelSeparator().getFromRepository(self)
self.executeTitle = 'Splodge'
def __init__(self):
"Set the default settings, execute title & settings fileName."
skeinforge_profile.addListsToCraftTypeRepository(
'skeinforge_application.skeinforge_plugins.craft_plugins.feed.html',
self)
self.fileNameInput = settings.FileNameInput().getFromFileName(
fabmetheus_interpret.getGNUTranslatorGcodeFileTypeTuples(),
'Open File for Feed', self, '')
self.activateFeed = settings.BooleanSetting().getFromValue(
'Activate Feed:', self, True)
self.feedRatePerSecond = settings.FloatSpin().getFromValue(
2.0, 'Feed Rate (mm/s):', self, 50.0, 16.0)
self.maximumZDrillFeedRatePerSecond = settings.FloatSpin(
).getFromValue(0.02, 'Maximum Z Drill Feed Rate (mm/s):', self, 0.5,
0.1)
self.travelFeedRatePerSecond = settings.FloatSpin().getFromValue(
2.0, 'Travel Feed Rate (mm/s):', self, 50.0, 16.0)
self.executeTitle = 'Feed'
def addScaleScreenSlide(self):
'Add the scale, screen and slide show settings.'
self.scale = settings.FloatSpinNotOnMenu().getFromValue(
10.0, 'Scale (pixels per millimeter):', self, 50.0, 15.0)
# This is needed to adjust for the ratio between the numbers
# reported by measure() and the pixel density of the monitor.
# unfortunately there seems to be no reliable way of calculating it.
self.pixelmagic = settings.FloatSpinNotOnMenu().getFromValue(
0.1, 'Font scale factor:', self, 10.0, 2.0)
settings.LabelSeparator().getFromRepository(self)
settings.LabelDisplay().getFromName('- Screen Inset -', self)
self.screenHorizontalInset = settings.IntSpin().getFromValue(
80, 'Screen Horizontal Inset (pixels):', self, 1000, 100)
self.screenVerticalInset = settings.IntSpin().getFromValue(
120, 'Screen Vertical Inset (pixels):', self, 1000, 220)
settings.LabelSeparator().getFromRepository(self)
self.showGcode = settings.BooleanSetting().getFromValue(
'Show Gcode', self, True)