def main():
global bus
global config
global activehome
bus = AutobusConnection()
activehome = bus["activehome"]
bus.add_interface("home", Interface())
config = Configuration(bus, "configure.home", "homed.conf")
bus.start_connecting()
bus.interrupt_loop()
def main():
global bus
global receive_event
global receive_action_event
pythoncom.CoInitialize()
try:
Dispatch("X10.ActiveHome") # Make sure we've got it before hand
except:
print_exc()
print "You need to install the ActiveHome Scripting SDK before you"
print "can use activehomed."
sys.exit()
print "Connecting to server " + str(os.getenv("AUTOBUS_SERVER"))
bus = AutobusConnection()
bus.add_interface("activehome", RPC())
receive_action_event = bus.add_event("activehome", "receive_action", """\
Fired when the CM15A receives a powerline or RF signal. This event is quite
low-level and hence the receive event should be preferred to this one. The
signature of this event is identical to the ActiveHome Scripting SDK's
OnRecvAction event, except that all parameters are passed as strings and
the last two parameters are not present (the scripting SDK doesn't make
use of those at present, so you're not losing any information).
""")
receive_event = bus.add_event("activehome", "receive", """\
receive(mode, house, unit, address, command, sequence, timestamp, repeat)
Fired when the CM15A receives a powerline or RF signal. This event is more
high-level than receive_action.
mode is the mode, which will either be plc or rf.
house is the house code. unit is the unit code. address is the string
concatenation of the house and unit codes. For example, house, unit, and
address could be "d", "2", and "d2", respectively. All three parameters are
passed as strings.
command is the command that occurred. The ActiveHome Scripting SDK contains
a list of all valid commands, but some of the more common ones are On, Off,
AllLightsOn, AllUnitsOff, Bright, Dim, PanLeft, CamGoPosition1, and
DeviceStop (the latter of which occurs when the CM15A is unplugged from the
computer).
sequence is slightly command-specific, as follows:
If this is an RF command, sequence will be the sequence number, which
is 0 for the button being pressed down, 1 and upward for holding
the button down (fired roughly six times per second), and -1 for
letting go of the button. A word of warning: this doesn't seem to
be hugely reliable. For example, pushing an on button on a ScanPad
or PalmPad results in six events: three pairs of button press and button
release commands, despite the fact that the button was only pressed
once. Holding the button down just repeats these pairs further. If you want
a reliable indicator of whether or not a button press is a repeat, use the
repeat parameter passed to this event.
If this is a powerline command, sequence will be null unless the command is
Bright or Dim, in which case it will be the bright/dim level. When a
bright/dim button is held down on an RF controller, the result is a
repeated firing of Bright/Dim commands. When a bright/dim button is held
down on a powerline controller, the result is that no events are fired
until the button is let go, and then a single Bright/Dim command is fired
with the sequence parameter being set to the percent change in brightness
that would have resulted had the command been directed at an actual module.
The timestamp parameter is only present for RF commands. It specifies, as
a string, the date and time at which the command was received. This
generally won't be used since Autobus only incurs a few milliseconds'
latency, so the date could just be detected locally.
repeat is a boolean. It will be set to true if this event is most likely a
repeat of another event. For example, if an on button on a ScanPad
controller is pressed, the result is three pairs of button press and button
release commands. The first command will have its repeat parameter set to
false, and the remaining five commands will have their repeat parameters
set to true. Another example is a bug in the CM15A: If two units were
simultaneously turned on (for example, by A1 A2 A off going across the
powerline), and then an AllLightsOn received on the powerline for that
house code, the CM15A will report that as two events: A1 AllLightsOff and
A2 AllLightsOff. The latter will be detected as a repeat when this event
is fired. NOTE: There are currently problems with detecting RF
bright/dim repeats, so you should generally ignore this parameter for
RF bright/dim commands.
""")
bus.start_connecting()
try:
HTTPServer(("127.0.0.1", port), HTTPHandler).serve_forever()
except KeyboardInterrupt:
print "Interrupted, shutting down"
finally:
bus.shutdown()
def init(context):
global bus
bus = AutobusConnection("spiro.afn")
bus.start_connecting()
