def main(argv):
if len(argv) != 2:
print """\
usage: %s <argfoop>
where <argfoop> is a valid foop.""" % (
prog_name
)
sys.exit(1)
else:
print "argv 1 is " + argv[1]
if probe(dev0):
print "Device not Found".dev0
sys.exit(1)
patWrkNum = 5 # pattern gen
smaWrkNum = 6 # SMA
plaWrkNum = 7 # Platform
gbeWrkNum = 9 # GBE
adcWrkNum = 10 # IQADC
dp0WrkNum = 13 # dgdp dp0
workerList = [5, 6, 7, 9, 10, 13]
print "Reset cycling each worker..."
for w in workerList:
print "Worker: " + str(w)
print "reset"
wreset(dev0, w)
print "unreset"
wunreset(dev0, w)
print "f-value timeout"
wwctl(dev0, w, 0x8000000F)
print "Testing admin scratch regsiters..."
testAdminReg(dev0, 0x20)
testAdminReg(dev0, 0x24)
print "Probing Worker Control Status ahead of init..."
for w in workerList:
rwsr(dev0, w)
print "Initializing each worker..."
for w in workerList:
wop(dev0, w, "initialize")
print "Probing Worker Control Status after init..."
for w in workerList:
rwsr(dev0, w)
print "Testing scratch registers..."
testScratchReg(dev0, 5, 0)
testScratchReg(dev0, 6, 0)
testScratchReg(dev0, 9, 0)
testScratchReg(dev0, 13, 0xB8)
print "Done."
sys.exit(0)
def main(argv):
if len(argv) != 2:
print """\
usage: %s <argfoop>
where <argfoop> is a valid foop.""" % (prog_name)
sys.exit(1)
else:
print 'argv 1 is ' + argv[1]
if probe(dev0):
print 'Device not Found'. dev0
sys.exit(1)
patWrkNum = 5 # pattern gen
smaWrkNum = 6 # SMA
plaWrkNum = 7 # Platform
gbeWrkNum = 9 # GBE
adcWrkNum = 10 # IQADC
dp0WrkNum = 13 # dgdp dp0
dp1WrkNum = 14 # dgdp dp1
workerList = [5,6,7,9,10,13,14]
print 'Reset cycling each worker...'
for w in workerList:
print 'Worker: ' + str(w)
print 'reset'
wreset(dev0, w)
print 'unreset'
wunreset(dev0, w)
print 'f-value timeout'
wwctl(dev0, w, 0x8000000F)
print 'Testing admin scratch regsiters...'
testAdminReg(dev0, 0x20)
testAdminReg(dev0, 0x24)
print 'Probing Worker Control Status ahead of init...'
for w in workerList:
rwsr(dev0, w)
print 'Initializing each worker...'
for w in workerList:
wop(dev0, w, 'initialize')
print 'Probing Worker Control Status after init...'
for w in workerList:
rwsr(dev0, w)
print 'Testing scratch registers...'
testScratchReg(dev0, 5, 0)
testScratchReg(dev0, 6, 0)
testScratchReg(dev0, 9, 0)
testScratchReg(dev0, 13, 0xB8)
testScratchReg(dev0, 14, 0xB8)
print 'Done.'
sys.exit(0)
def main(argv):
if len(argv) != 2:
print """\
usage: %s <argfoop>
where <argfoop> is a valid foop.""" % (prog_name)
sys.exit(1)
else:
print 'argv 1 is ' + argv[1]
if probe(dev0):
print 'Device not Found'. dev0
sys.exit(1)
pat0WrkNum = 2 # Pattern
biasWrkNum = 3 # Bias
cap0WrkNum = 4 # Capture
workerList = [2,3,4]
print 'Reset cycling each worker...'
for w in workerList:
print 'Worker: ' + str(w)
print 'reset'
wreset(dev0, w)
print 'unreset'
wunreset(dev0, w)
# Modification for extended timeout...
#print 'f-value timeout'
#wwctl(dev0, w, 0x8000000F)
#print 'Testing admin scratch regsiters...'
#testAdminReg(dev0, 0x20)
#testAdminReg(dev0, 0x24)
wadmin(dev0, 0x20, 0xFEEDC0DE)
wadmin(dev0, 0x24, 0xBABECAFE)
print 'Probing Worker Control Status ahead of init...'
for w in workerList:
rwsr(dev0, w)
print 'Initializing each worker...'
for w in workerList:
wop(dev0, w, 'initialize')
wwrite(dev0, pat0WrkNum, 0x04, 0x00000001);
print 'Reading Config Prop status regs...'
wread(dev0, pat0WrkNum, 0x1C);
wread(dev0, cap0WrkNum, 0x0C);
print 'Starting each worker...'
for w in workerList:
wop(dev0, w, 'start')
print 'Write capture enable bit...'
wwrite(dev0, cap0WrkNum, 0x00, 0x00000001);
print 'Set Page Register to Metadata on Pattern Generator...'
wwpage(dev0, pat0WrkNum, 0x400);
print 'Write Metadata...'
wwrite(dev0, pat0WrkNum, 0x0000, 0x00000080); # 32*4=128
wwrite(dev0, pat0WrkNum, 0x0004, 0x00000002); # opcode 2
wwrite(dev0, pat0WrkNum, 0x0008, 0x00000042);
wwrite(dev0, pat0WrkNum, 0x000C, 0x00000043);
print 'Set Page Register to Data Region on Pattern Generator...'
wwpage(dev0, pat0WrkNum, 0x800);
print 'Write Data Region...'
#wwrite(dev0, pat0WrkNum, 0x0000, 0x03020100);
#wwrite(dev0, pat0WrkNum, 0x0004, 0x07060504);
#wwrite(dev0, pat0WrkNum, 0x0008, 0x0B0A0908);
#wwrite(dev0, pat0WrkNum, 0x000C, 0x0F0E0D0C);
#wwrite(dev0, pat0WrkNum, 0x0010, 0x13121110);
startWord = 0x03020100;
for i in range(32):
wwrite(dev0, pat0WrkNum, i*4, i);
print 'ReturnPage Register to 0 on Pattern Generator...'
wwpage(dev0, pat0WrkNum, 0x0); # Page 0
print 'Write Data Region...'
wwrite(dev0, pat0WrkNum, 0x0010, 0x00000003); # send 3 messages
wwrite(dev0, pat0WrkNum, 0x0000, 0x00000001); # Fire!
print 'Command Sequence complete and fired!'
#print 'Probing Worker Control Status after init...'
#for w in workerList:
# rwsr(dev0, w)
#print 'Testing scratch registers...'
#print 'sma0'
#testScratchReg(dev0, pat0WrkNum, 0)
#print 'bias'
#testScratchReg(dev0, biasWrkNum, 0x4)
#print 'sma1'
#testScratchReg(dev0, cap0WrkNum, 0)
print 'Done.'
sys.exit(0)
